Chang'e 5 Undergoing Thermal Test

Chang’e 5 probe has entered its critical phase of AIT.Units,except the lander,are undergoing thermal test.The flight model of Chang’e 5 is composed of an orbiter,a return capsule,a lander and an ascent unit.The thermal tests on the ascent unit,the lander-as-

Thermal Performance Analysis of Plaster Reinforced with Raffia Vinifera Particles for Use as Insulating Materials in Building

The present study focuses on the formulation of new composite consisting of plaster and raffia vinifera particle (RVP) with the purpose to reducing energy consumption. The aim of this study is to test this new compound as an insulating eco-material in building in a tropical climate. The composites samples were developed by mixing plaster with raffia vinifera particles (RVP) using three different sizes (1.6 mm, 2.5 mm and 4 mm). The effects of four different RVP incorporations rates (i.e., 0wt%, 5wt%;10wt%;15wt%) on physical, thermal, mechanicals properties of the composites were investigated. In addition, the use of the raffia vinifera particles and plaster based composite material as building envelopes thermal insulation material is studied by the habitable cell thermal behavior instrumentation. The results indicate that the incorporation of raffia vinifera particle leads to improve the new composite physical, mechanical and thermal properties. And the parametric analysis reveals that the sampling rate and the size of raffia vinifera particles are the most decisive factor to impact these properties, and to decreases in the thermal conductivity which leads to an improvement to the thermal resistance and energy savings. The best improvement of plaster composite was obtained at the raffia vinifera particles size between 2.5 and 4.0 mm loading of 5wt% (C95P5R) with a good ratio of thermo-physical-mechanical properties. Additionally, the habitable cell experimental thermal behavior, with the new raffia vinifera particles and plaster-based composite as thermal insulating material for building walls, gives an average damping of 4°C and 5.8°C in the insulated house interior environment respectively for cold and hot cases compared to the outside environment and the uninsulated house interior environment. The current study highlights that this mixture gives the new composite thermal insulation properties applicable in the eco-construction of habitats in tropical environments.

Development of Morus alba Reinforced Poly-Lactic Acid with Elevated Mechanical and Thermal Properties

This research investigates the mechanical and thermal properties of Morus alba combined with polylactic acid in comparison with other natural fibers. The study uses three different fiber and PLA compositions - 20%, 30%, and 40% respectively - to produce composite materials. In addition, another composite with the same fiber volume is treated with a 4% NaOH solution to improve mechanical properties. The composites are processed by twin-screw extrusion, granulation, and injection molding. Tensile strength measurements of raw fibers and NaOH-treated fibers were carried out using a single-fiber tensile test with a gauge length of 40 mm. It was observed that the NaOH surface treatment increases the resistance against tensile loading and exhibited improved properties for raw fiber strands. The diameter of the fibers was measured using optical microscopy. During this research, flexural tests, impact tests, differential scanning calorimetry (DSC), and heat deflection temperature measurements (HDT) were conducted to evaluate the mechanical and thermal properties of the developed composite samples. The results indicate that the mechanical properties of NaOH-treated Morus alba-reinforced polylactic acid outperform both virgin PLA samples and untreated Morus alba samples.

A novel intelligent adaptive control of laser-based ground thermal test

Laser heating technology is a type of potential and attractive space heat flux simulation technology, which is characterized by high heating rate, controlled spatial intensity distribution and rapid response. However, the controlled plant is nonlinear, time-varying and uncertainty when implementing the laser-based heat flux simulation. In this paper, a novel intelligent adaptive controller based on proportion-integration-differentiation (PID) type fuzzy logic is proposed to improve the performance of laser-based ground thermal test. The temperature range of thermal cycles is more than 200 K in many instances. In order to improve the adaptability of controller, output scaling factors are real time adjusted while the thermal test is underway. The initial values of scaling factors are optimized using a stochastic hybrid particle swarm optimization (H-PSO) algorithm. A validating system has been established in the laboratory. The performance of the proposed controller is evaluated through extensive experiments under different operating conditions (reference and load disturbance). The results show that the proposed adaptive controller performs remarkably better compared to the conventional PID (PID) controller and the conventional PID type fuzzy (F-PID) controller considering performance indicators of overshoot, settling time and steady state error for laser-based ground thermal test. It is a reliable tool for effective temperature control of laser-based ground thermal test. (C) 2016 Chinese Society of Aeronautics and Astronautics. Production and hosting by Elsevier Ltd. This is an open access article under the CC BY-NC-ND license.

Thermal test and numerical simulation of cooling stave with internal ribbed tube

A new type of cooling stave with internal ribbed tube was proposed,and the heat transfer performance of the stave was studied by means of thermal test and numerical simulation.The temperature of cooling stave was monitored in the conditions of furnace gas temperature of 200-700 C and cooling water velocity of 0.2-1.0 m/s.The thermal test results show that the internal rib structure can form swirl in the water pipe and improve the cooling capacity of the cooling stave.The higher the furnace temperature or the lower the cooling water flow rate,the more obvious the advantage of the cooling stave with internal ribbed tube.The mathematical model of the cooling stave with internal ribbed tube was established by FLUENT software,and the influence of the internal rib structure parameters on the heat transfer performance of the cooling stave was discussed.It is suggested that the parameters of the internal ribbed tube should be 4 ribs,1 mm in height,5-7 mm in width,and 20-30 mm in lead.In the same common working conditions of the cooling stave,the maximum temperature of the newly designed cooling stave with internal ribbed tube is reduced by 5.6%compared with that of common cooling stave with round tube.The water flow rate in the internal ribbed tube only needs 0.9 m/s to reach the cooling effect of 2 m/s in the common tube cooling stave,which can save 55%of water.In case of water shortage accident of cooling stave,the maximum temperature of the cooling stave with internal ribbed tube is decreased by 22.4%compared with that of common round tube,which can effectively reduce the harm of water shortage and protect the cooling stave.

Investigation on the test method of rupture forces of thermal bonding seams in nonwovens shopping bags

超声波热黏合的非织造布接缝不同于普通机织物和针织物等的车缝接缝。运用正交试验设计方法，对纺粘法PP非织造布购物袋热黏合接缝断裂强力测试中的试样宽度、拉伸速率和隔距三个因素进行优化。试验结果表明，试样宽度对纺粘法PP非织造布热黏合接缝断裂强力的测试结果影响最大，并且接缝的断裂强力随着试样宽度的增加而增加。选用试样宽度为200mm、拉伸速率为50mm／min、隔距为100mm的组合所得出的测试结果能比较真实地反映实际的接缝断裂强力。

Thermal fatigue behaviors of SiC power module by Ag sinter joining under harsh thermal shock test

The excellent properties of SiC bring new challenges for the device packaging.In this study,the bonding strength,fracture behaviors and microstructural evolution of micron-porous Ag joint were elevated during thermal cycling(–50 ℃–250 ℃) in SiC/DBC(direct bonding copper) die attachment structure for different time.During harsh thermal shock test,the strength of sintered joint deceased gradually with the increase of cycling number,and the value just was half of the value of as-sintered after 1 000 cycles.Coarsening of Ag grains was observed in micron-porous joint with the structure inhomogeneity and defects increasing,which were the reasons of the strength decease.In addition,it was also found that the fracture behavior of sintered joints was changed from ductile deformation of Ag grain to brittle fracture of crack propagation after 1 000 cycles.This study will add the understanding in the mechanical properties of Ag sinter joining and its applications at high temperature.

Characterization of Failure Mechanisms of Duplex and Graded Thermal Barrier Coatings Exposed to Thermal Shock Test

The beginning of failure of a (ZrO2-7%Y2O3)/(Ni-22%Co-17%Cr-12.5%Al-0.6%Y) duplex andgraded coating systems on lnconel 617 and IN738LC in burner rig tests has been characterized.The test conditions are 40 s heating up to 75O℃ substrate temperature followed by 80 s aircooling. Failure is considered at the appearance of the first bright spot during heating period.Stresses due to thermal expansion mismatch strains on cooling are the probable cause of life-limiting in this conditions of testing.

Thermal Response Test by Improved Test Rig with Heating or Cooling Soil

An improved test rig providing both the heat and cold source was used to perform thermal response test(TRT), and the line source model was used for data analysis. The principle of determining the temperature difference between the inlet and outlet of test well can keep the heating or cooling rate constant, along with a reduced size of test rig. Among the influencial factors of the line source model, the temperature difference was determined as the most important, which agreed with the test results. When the gravel was taken as the backfill material, the soil thermal conductivities of heating and cooling at the test place were 1.883 W/(m·K) and 1.754 W/(m·K), respectively, and the deviation of TRT between heating and cooling soil was 6.8%. In the case of fine sand, the thermal conductivities of heating and cooling were 1.541 W/(m·K) and 1.486 W/(m·K), respectively, and the corresponding deviation was 6%. It was also concluded that different velocities of water had less influence on TRT than the temperature difference.

A test method for evaluating the thermal environment of underground coal mine refuge alternatives

Since 2009,the Mine Safety and Health Administration(MSHA)has required mines to install refuge alternatives(RAs)in underground coal mines.One of the biggest concerns with occupied RAs is the possible severity of the resulting thermal environment.In 30 CFR 7.504,the maximum allowable apparent temperature(AT)for an occupied RA is specified as 35℃(95°F).Manufacturers must conduct heat/humidity tests to demonstrate that their RAs meet the 35℃(95°F)AT limit.For these tests,heat input devices are used to input the metabolic heat of actual miners.A wide variety of test methods,sensors,and heat input devices could be used when conducting such tests.Since 2012,the National Institute for Occupational Safety and Health(NIOSH)has conducted over thirty 96-hour heat/humidity tests on four different RAs.This paper discusses the test equipment and procedures used during these investigations.This information is useful for RA manufacturers conducting RA heat/humidity tests,for other researchers investigating RA heat/humidity buildup,and for those who need to assess the thermal environment of any confined space where people may be trapped or are seeking refuge.

Extended application of the tension test in thermal simulator Thermecmastor-Z

With the redesigned jigs for the Thermecmastor-Z thermal simulator,the feasibility of using 3 kinds of Gleeble specimens in the Thermecmastor-Z simulator was investigated. Results show that Gleeble specimens can be used in the Thermecmastor-Z simulator. The tension tests in the Gleeble and Thermecmastor-Z simulators produced results with the same trend,which proves that the high temperature ductility of Gleeble specimens can be reflected by the Thermecmastor- Z simulator. In addition,as the Thermecmastor-Z simulator offers a wider heating zone,better cross-section shrinkage and elongation of specimens can be achieved under the same test conditions.

Thermal analysis and tests of W/Cu brazing for primary collimator scraper in CSNS/RCS

To the transverse beam collimation system in a rapid cycling synchrotron,an important component is the primary collimator,which improves emittance of the beam halo particles such that the particles outside the predefined trajectory can be absorbed by the secondary collimators.Given the material properties and power deposition distribution,the beam scraper of the primary collimator is a0.17 mm tungsten foil on a double face-wedged copper block of 121.5 mm x 20 mm.The heat is transferred to the outside by a φ34 mm copper rod.In this paper,for minimizing brazing thermal stress,we report our theoretical analysis and tests on brazing the tungsten and copper materials which differ greatly in size.We show that the thermal stress effect can be controlled effectively by creating stress relief grooves on the copper block and inserting a tungsten transition layer into the copper block.This innovation contributes to the successful R&D of the primary collimator.And this study may be of help for working out a brazing plan of similar structures.

Determination of the Thermal Expansion Coefficient of Concrete at Early Ages by Using Temperature-stress Testing Machine

By using the uptodate temperatuer-stress testing machine, the thermal expansion coefficient of concrete at early ages was studied and indicative conclusions were achieved ： temperature rising due to hydration heat is not directly correlated with cracking, but the temperature and stress evolation process should be taken into consideration in the same time. Proper chemical admixtures and mineral cornpasitions can improve the mechanical properties of concrete such as thermal expansion coefficient, which is very indicative in practice.

Interface fracture toughness and fracture mechanisms of thermal barrier coatings investigated by indentation test and acoustic emission technique

Interface fracture toughness and fracture mechanisms of plasma-/sprayed thermal barrier coatings （TBCs） were investigated by interfacial indentation test （ HT） in combination with acoustic emission （ AE ） measurement. Critical load and AE energy were employed to calculate interface fracture toughness. The critical point at which crack appears at the interface was determined by the HT. AE signals produced during total indentation test not only are used to investigate the interface cracking behavior by Fast Fourier Transform （FFT） and wavelet transforms but also supply the mechanical information. The result shows that the AE signals associated with coating plastic deformation during indentation are of a more continuous type with a lower characteristic frequency content （30 -60 kHz） , whereas the instantaneous relaxation associated with interface crack initiation produces burst type AE signals with a characteristic frequency in the range 70 - 200 kHz. The AE signals energy is concentrated on different scales for the coating plastic deformation, interface crack initiation and interface crack propagation. Interface fracture toughness calculated by AE energy was 1. 19 MPam1/2 close to 1.58 MPam1/2 calculated by critical load. It indicates that the acoustic emission energy is suitable to reflect the interface fracture toughness.

复杂石墨阵列快速时变热耦合控制方法

为了在高超声速飞行器结构热试验中准确模拟真实服役热环境,用快速时变热耦合控制方法对复杂石墨阵列进行控制.采用热耦合控制方法将瞬态热损失与瞬态黑体辐射量代入控制方程,实时获取试验件的真实热响应状态;研究了结构热试验热载荷典型历程及石墨阵列控制响应特性,设计了基于结构热试验的专家PID控制策略,给出了复杂石墨阵列全历程分段控制参数;研究了石墨阵列的电特性,设计了时变限伏控制策略,提高了石墨阵列的可靠性;设计了一种多温区耦合补偿控制方法,减小了温区间的耦合干扰.结果表明:试验得到的温度曲线与理论计算曲线在快速升温段的最大误差为4.8%,平稳段的最大误差为1.4%,下降段的最大误差为2.3%;有效减小了控制系统的超调量,提高了系统响应速度;使用快速时变热耦合控制方法在某试验中对复杂石墨阵列进行控制,控制误差小于1.2%.

高超声速飞行器热-结构试验若干关键技术

热-结构试验是高超声速飞行器研制过程中不可或缺的环节。本文在给出热-结构试验内涵与特征的基础上,结合热-结构试验典型科目介绍,呈现了热-结构试验体系总体架构,为全面了解热-结构试验提供参考;其次重点分析了当前热-结构试验中亟待突破的时变超高温热载实现、局部热载大梯度模拟以及时/频域载荷协同等7大关键技术。

基于组合热流模拟策略的遥感卫星热平衡试验设计与验证

针对某型遥感卫星的不同区域对高精度热流模拟的需求,文章提出一种组合热流模拟策略:以红外加热笼来实现卫星舱板表面的外热流模拟,用薄膜电加热器实现卫星外露复杂表面外热流模拟。试验结果表明,在文述参试卫星状态及所采取的热设计措施下,该方法可对卫星低温初期、高温末期和高温热真空工况下的外热流进行精准模拟,并可有效考核遥感卫星的热控设计。该热流模拟策略可为卫星瞬态功耗散热设计的优化提供参考依据,为我国未来光学遥感卫星的热平衡试验及验证提供技术支撑。

泄压孔对聚能传爆管的影响

以炸药在点燃瞬间的压力均衡为前提条件,计算聚能传爆管点火后只产生燃烧反应的最小泄压孔面积,以此为基础,对含不同尺寸泄压结构的聚能传爆管在慢速烤燃和快速烤燃环境下的响应特性进行分析,在建立三维轴对称烤燃计算模型的基础上,采用Fluent对不同大小泄压孔的慢速烤燃响应特性进行数值模拟。为研究含泄压孔聚能传爆管对起爆威力性能的影响,对3种不同大小泄压孔的聚能传爆管进行了起爆实验。结果表明,该型聚能传爆管的泄压孔设计单孔直径7 mm为最优,研究结果对水雷不敏感引信的结构设计有一定的指导意义。