Experimental investigation into effects of the natural polymer and nanoclay particles on the EOR performance of chemical flooding in carbonate reservoirs

This paper aims to investigate the tragacanth gum potential as a natural polymer combined with natural clay mineral(montmorillonite,kaolinite,and illite)nanoparticles(NPs)to form NP-polymer suspension for enhanced oil recovery(EOR)in carbonate reservoirs.Thermal gravimetric analysis(TGA)tests were conducted initially in order to evaluate the properties of tragacanth gum.Subsequently,scanning electron microscopy(SEM)and energy-dispersive X-ray(EDX)tests were used to detect the structure of clay particles.In various scenarios,the effects of natural NPs and polymer on the wettability alteration,interfacial tension(IFT)reduction,viscosity improvement,and oil recovery were investigated through contact angle system,ring method,Anton Paar viscometer,and core flooding tests,respectively.The entire experiment was conducted at 25,50,and 75℃,respectively.According to the experimental results,the clay minerals alone did not have a significant effect on viscosity,but the addition of minerals to the polymer solution leads to the viscosity enhancement remarkably,resulting mobility ratio improvement.Among clay NPs,the combination of natural polymer and kaolinite results in increased viscosity at all temperatures.Considerable wettability alteration was also observed in the case of natural polymer and illite NPs.Illite in combination with natural polymer showed an ability in reducing IFT.Finally,the results of displacement experiments revealed that the combination of natural polymer and kaolinite could be the best option for EOR due to its substantial ability to improve the recovery factor.

Layered injection technology for chemical flooding of Class-Ⅲ oil reservoirs in the Daqing Oil Fields complex,Songliao Basin,Northeast China

The Class-Ⅲ oil reservoirs of Lasaxing oilfield in the Daqing Oil Fields complex have geological oil reserves of 1.86 billion tonnes,an oil recovery of 39%,with remaining reserves accounting for more than 45%of the total geological reserves of the oilfield.Therefore,they have considerable potential for future oil production.The current layered injection technologies fail to achieve effective control over the low single-layer injection rates since they can only produce low throttle differential pressure under low injection rates(5-20 m^(3)/d).In this study,a symmetrically-structured double-offset-hole injection allocator and a novel throttling component were developed.Their spatial layout was constructed and mechanical parameters were optimized using finite element analysis,which allows for expanding the flow rate range at low injection rates.According to experimental results,the throttle differential pressure increased from 0.2 MPa to 0.8 MPa at an injection rate of 5 m^(3)/d,and the range of the single-layer flow rates expanded from 20-70 m^(3)/d to 5-70 m3/d.The field test results show that the effective production of oil layers with medium and low permeability was achieved and that the ratio of producing oil layer thickness to the total reservoir thickness increased by 9.7%on average.Therefore,this study provides valuable technical support for the effective chemical-flooding-based development of Class-Ⅲ oil reservoirs.

Quantitative Description of the Effects of Sweep Efficiency and Displacement Efficiency during Chemical Flooding on a Heterogeneous Reservoir

The processes of flooding—water flooding, polymer flooding and ternary combination flooding—were simulated respectively on a 2-D positive rhythm profile geological model by using the ASP numerical modeling software developed by RIPED (Yuan, et al. 1995). The recovery coefficient, remaining oil saturation, sweep efficiency and displacement efficiency were calculated and correlated layer by layer. The results show that the sweep efficiency and displacement efficiency work different effects on different layers in the severely heterogeneous reservoir. The study shows that the displacement efficiency and sweep efficiency play different roles in different layers for severely heterogeneous reservoirs. The displacement efficiency contributes mainly to the high permeability zones, the sweep efficiency to the low permeability zones, both of which contribute to the middle permeable zones. To improve the sweep efficiency in the low permeability zones is of significance for enhancing the whole recovery of the reservoir. It is an important path for improving the effectiveness of chemical flooding in the severely heterogeneous reservoirs to inject ternary combination slug after profile control.

Effect of Processing and Cultivar on Thermo-Chemical Properties of Australian-Grown Hemp Hurd(Cannabis sativa L.)

This study explored the thermo-chemical properties of industrial hemp hurd with different provenances,maturity stages,and retting protocols.The findings were then compared to hemp hurd used in the fabrication of citric acid-bonded ultra-low-density hemp hurd particleboard.Pyrolysis-gas chromatography-mass spectrometry(Py-GC/MS),Fourier-transform infrared spectroscopy(FTIR),and thermogravimetric analysis(TGA)were employed to document the variability of the hurd and comprehend the potential impact on biobased composite applications.The choice of cultivar,maturity stage,and processing modality significantly influenced the chemical composition,presence of functional groups,and thermal stability of the hurd.Py-GC/MS revealed substantial variations in the lignin-to-carbohydrate(L/C)ratio,along with the absence of fatty acids in certain cultivars.While FTIR signals confirmed consistent functional groups,differences in peak intensities were indicative of carbohydrate variations associated with maturity and retting duration,impacting the availability of hydroxyl groups for,i.e.,interparticle bonding in citric acid-based bio-composites.Furthermore,it was observed that shorter retting durations initially enhanced the thermal resistance,but prolonged retting led to accelerated degradation,significantly reducing the hurd’s residual mass.The findings indicated notable differences among the samples,emphasizing the importance of investigating variables such as provenance/cultivar,maturity,and processing modality.This assessment is essential to ensure effective agronomic practices that align the raw material characteristics with the specific requirements of intended applications,such as the fabrication of biobased hemp hurd composites.

Dissipative particle dynamics simulation of wettability alternation phenomena in the chemical flooding process

Wettability alternation phenomena is considered one of the most important enhanced oil recovery （EOR） mechanisms in the chemical flooding process and induced by the adsorption of surfactant on the rock surface. These phenomena are studied by a mesoscopic method named as dissipative particle dynamics （DPD）. Both the alteration phenomena of water-wet to oil-wet and that of oil-wet to water-wet are simulated based on reasonable definition of interaction parameters between beads. The wetting hysteresis phenomenon and the process of oil-drops detachment from rock surfaces with different wettability are simulated by adding long-range external forces on the fluid particles. The simulation results show that, the oil drop is liable to spread on the oil-wetting surface and move in the form of liquid film flow, whereas it is likely to move as a whole on the waterwetting surface. There are the same phenomena occuring in wettability-alternated cases. The results also show that DPD method provides a feasible approach to the problems of seepage flow with physicochemical phenomena and can be used to study the mechanism of EOR of chemical flooding.

Numerical simulation of pore-scale flow in chemical flooding process

Chemical flooding is one of the effective technologies to increase oil recovery of petroleum reservoirs after water flooding.Above the scale of representative elementary volume(REV), phenomenological modeling and numerical simulations of chemical flooding have been reported in literatures,but the studies alike are rarely conducted at the pore-scale,at which the effects of physicochemical hydrodynamics are hardly resolved either by experimental observations or by traditional continuum-based simulations.In this paper,dissipative particle dynamics(DPD),one of mesoscopic fluid particle methods,is introduced to simulate the pore-scale flow in chemical flooding processes.The theoretical background,mathematical formulation and numerical approach of DPD are presented.The plane Poiseuille flow is used to illustrate the accuracy of the DPD simulation,and then the processes of polymer flooding through an oil-wet throat and a water-wet throat are studies, respectively.The selected parameters of those simulations are given in details.These preliminary results show the potential of this novel method for modeling the physicochemical hydrodynamics at the pore scale in the area of chemical enhanced oil recovery.

Treatment of Oil Field Wastewater after Chemical Flooding by Fenton Oxidation Combined with Biodegradation

Wastewater after chemical flooding is difficult to be treated by biological methods due to the residual chemicals in the wastewater. Fenton oxidation, which has been widely applied to detoxifying hazardous organic compounds and improving the biodegradability of these compounds, can solve this problem. So, in this paper, Fenton oxidation was used to enhance the biodegradability of the wastewater after chemical flooding. The op- timum operating conditions for the Fenton oxidation process were 2.5 g/L Fe2 ＋ , 600 mg/L H202 and 30 rain of treatment time. The wastewater pre- treated by Fenton oxidation was treated by aerobic activated sludge. It was found that a small amount of H202 can significantly increase both the biodegradation rate and extent of the wastewater. The effluent CODc, and HPAM contents were 260 and 94 mg/L respectively after the aerobic bio- logical process with the biodegradation time of 24 h. After Fenton oxidation combining with biodegradation, the total CODc, removal efficiency was up to 90%, and polymer and oil degrading efficiencies were 95% and 92% respectively.

PREPARATION,IDENTIFICATION AND INTERFACIAL ACTIVITIES OF PETROLEUM CARBOXYLATE AS SURFACTANT FOR CHEMICAL FLOODING

Petroleum carboxylate that may be suitable for tertiary oil recovery have been produced inexpensively from the fractions of Daqing crude oil by a two step process.The feed stock was first oxidized in the vapor phase,followed by reaction of the oxidized products with sodium hydroxide.Dilute solutions of sodium carboxylates were produced and show ultralow(10^(-2)mN/m)interfacial tensions(IFTs)against a variety of hydrocarbons with a wide range of ACN(Alkane Carbon Number).Infrared spectroscopy was used to identify the functional groups in the oxidized and the saponified products.

Technologies of enhancing oil recovery by chemical flooding in Daqing Oilfield, NE China

By tracking and analyzing the research and practices of chemical flooding carried out in the Daqing Oilfield, NE China since the 1970 s, the chemical flooding theory, technology adaptability and existing problems were systematically summarized, and directions and ideas of development in the future were proposed. In enhanced oil recovery by chemical flooding, the Daqing Oilfield developed theories related to compatibility between crude oil and surfactant that may form ultra-low interfacial tensions with low-acidity oil, and a series of surfactant products were developed independently. The key technologies for chemical flooding such as injection parameter optimization and numerical simulation were established. The technologies of separation injection, cleansing and anti-scaling, preparation and injection, and produced liquid processing were developed. The matching technologies of production engineering and surface facilities were formed. Through implementation of chemical flooding, the Daqing Oilfield achieved outstanding performances with enhanced recovery rate of 12% in polymer flooding and with enhanced recovery rate of 18% in ASP flooding. To further enhance the oil recovery of chemical flooding, three aspects need to be studied:(1) fine characterization of reservoirs;(2) smart and efficient recovery enhancement technologies;(3) environment friendly, high-efficiency and smart matching processes.

Feasibility Study on Chemical Flooding in Super High Porosity and Permeability Heavy Oil Reservoir

In this paper, the feasibility study of chemical flooding is carried out for ultra-high porosity and high permeability heavy oil field with permeability higher than 10 μm2 and porosity greater than 35%. The viscosity-concentration relationship of four kinds of oil flooding systems such as hydrolyzed polyacrylamide, structural polymer A, structural polymer B and gel was studied. The results showed that the viscosity of ordinary polymer and structural polymer B was lower compared with other two types of oil displacement agents, and the viscosity of structural polymer A was higher. The higher the concentration, the higher the viscosity retention rate. The gel system has the highest viscosity and best anti-shear ability. The resistance coefficient and residual resistance coefficient of structural polymer A and gel system were further studied. The results show that permeability, velocity and polymer concentration all affect the resistance coefficient and residual resistance coefficient. From the point of view of resistance establishment ability, it is considered that structural polymer A is not suitable for permeability formation above 10 μm2. Gel system has stronger ability to establish resistance coefficient than structural polymer A flooding system, and it is more feasible for formation system with permeability above 10 μm2.

Impact of solutal Marangoni convection on oil recovery during chemical flooding

In this study,the impacts of solutal Marangoni phenomenon on multiphase flow in static and micromodel geometries have experimentally been studied and the interactions between oil droplet and two different alkaline solutions(i.e.MgS04 and Na_2 CO_3) were investigated.The static tests revealed that the Marangoni convection exists in the presence of the alkaline and oil which should carefully be considered in porous media.In the micromodel experiments,observations showed that in the MgS04 flooding,the fluids stayed almost stationary,while in the Na2 C03 flooding,a spontaneous movement was detected.The changes in the distribution of fluids showed that the circular movement of fluids due to the Marangoni effects can be effective in draining of the unswept regions.The dimensional analysis for possible mechanisms showed that the viscous,gravity and diffusion forces were negligible and the other mechanisms such as capillary and Marangoni effects should be considered in the investigated experiments.The value of the new defined Marangoni/capillary dimensionless number for the Na2 C03 solution was orders of magnitude larger than the MgS04 flooding scenario which explains the differences between the two cases and also between different micromodel regions.In conclusion,the Marangoni convection is activated by creating an ultra-low IFT condition in multiphase flow problems that can be profoundly effective in increasing the phase mixing and microscopic efficiency.

Production calculation of the second and tertiary recovery combination reservoirs under chemical flooding

Based on the analysis of the production composition of reservoirs developed by the second&tertiary recovery combination(STRC),the relationship between the overall output of the STRC project and the production level during the blank water flooding stage is proposed.According to the basic principle of reservoir engineering that the“recovery factor is equal to sweeping coefficient multiplied by oil displacement efficiency”,the formula for calculating the ultimate oil recovery factor of chemical combination flooding reservoir was established.By dividing the reservoir into a series of grids according to differen-tial calculus thinking,the relationship between the ultimate recovery factor of a certain number of grids and the recovery de-gree of the reservoir was established,and then the variation law of oil production rate of the STRC reservoir was obtained.The concept of“oil rate enlargement factor of chemical combination flooding”was defined,and a production calculation method of reservoir developed by STRC was put forward based on practical oilfield development experience.The study shows that the oil production enhancing effect of STRC increases evenly with the in crease of the ratio of STRC displacement efficiency to water displacement efficiency,and increases rapidly with the increase of the ratio of recovery degree at flooding mode conversion to the water displacement efficiency.STRC is more effective in increasing oil production of reservoir with high recovery degree.Through practical tests of the alkali free binary flooding(polymer/surfactant)projects,the relative error of the oil production calculation method of STRC reservoir is about±10%,which meets the requirements of reservoir engineering.

Theory and Application of Numerical Simulation of Chemical Flooding in High Temperature and High Salt Reservoirs

Applications, theoretical analysis and numerical methods are introduced for the simulation of mechanical models and principles of the porous flow in high temperature, high salt, complicated geology and large-scale reservoirs in this paper. Considering petroleum geology, geochemistry, computational permeation fluid mechanics and computer technology, we state the models of permeation fluid mechanics and put forward a sequence of implicit upwind difference iteration schemes based on refined fractional steps of the upstream, which can compute the pressures, the saturation and the concentrations of different chemistry components. A type of software applicable in major industries has been completed and carried out in numerical analysis and simulations of oil extraction in Shengli Oil-field, which brings huge economic benefits and social benefits. This software gives many characters: spatial steps are taken as ten meters, the number of nodes is up to hundreds of thousands and simulation time period can be tens of years and the high-order accuracy can be promised in numerical data. Precise analysis is present for simplified models of this type and that provides a tool to solve the international famous problem.

Study of steam heat transfer enhanced by CO_(2) and chemical agents: In heavy oil production

Steam flooding with the assistance of carbon dioxide (CO_(2)) and chemicals is an effective approach for enhancing super heavy oil recovery. However, the promotion and application of CO_(2) and chemical agent-assisted steam flooding technology have been restricted by the current lack of research on the synergistic effect of CO_(2) and chemical agents on enhanced steam flooding heat transfer. The novel experiments on CO_(2)–chemicals cooperate affected steam condensation and seepage were conducted by adding CO_(2) and two chemicals (sodium dodecyl sulfate (SDS) and the betaine temperature-salt resistant foaming agent ZK-05200).According to the experimental findings, a “film” formed on the heat-transfer medium surface following the co-injection of CO_(2) and the chemical to impede the steam heat transfer, reducing the heat transfer efficiency of steam, heat flux and condensation heat transfer coefficient. The steam seepage experiment revealed that the temperature at the back end of the sandpack model was dramatically raised by 3.5–12.8 °C by adding CO_(2) and chemical agents, achieving the goal of driving deep-formation heavy oil. The combined effect of CO_(2) and SDS was the most effective for improving steam heat transfer, the steam heat loss was reduced by 6.2%, the steam condensation cycle was prolonged by 1.3 times, the condensation heat transfer coefficient was decreased by 15.5%, and the heavy oil recovery was enhanced by 9.82%. Theoretical recommendations are offered in this study for improving the CO_(2)–chemical-assisted steam flooding technique.

Influence of Thermophoresis and Brownian Motion of Nanoparticles on Radiative Chemically-Reacting MHD Hiemenz Flow over a Nonlinear Stretching Sheet with Heat Generation

In this study,a radiative MHD stagnation point flow over a nonlinear stretching sheet incorporating thermophoresis and Brownian motion is considered.Using a similarity method to reshape the underlying Partial differential equations into a set of ordinary differential equations(ODEs),the implications of heat generation,and chemical reaction on the flow field are described in detail.Moreover a Homotopy analysis method(HAM)is used to interpret the related mechanisms.It is found that an increase in the magnetic and velocity exponent parameters can damp the fluid velocity,while thermophoresis and Brownian motion promote specific thermal effects.The results also demonstrate that as the Brownian motion parameter is increased,the concentration values become smaller.

Chemical stability, thermal behavior, and shelf life assessment of extruded modified double-base propellants

Double base propellant suffers from lack of chemical stability; this could result in self ignition during storing. Modified double base(MDB) propellant based on stoichiometric binary mixture of oxidizermetal fuel(Ammonium perchlorate/Aluminum), and energetic nitramines(HMX) offered enhanced thrust as well as combustion characteristics. This study is devoted to evaluate the impact of such energetic additives on thermal behavior, chemical stability, and shelf life. Extruded MDB formulations were manufactured by extrusion process. Artificial aging at 80℃ for 28 days was conducted. Shelf life assessment was performed using Van't Hoff's equation. Quantification of evolved NOxgases with aging time was performed using quantitative stability tests. MDB formulation based on HMX demonstrated extended service life of 16 years compared with(AP/Al)-MDB which demonstrated 9 years. This finding was ascribed to the reactivity of AP with nitroglycerin with the formation of perchloric acid. Thermal behavior of aged MDB, exhibited an increase in heat released with time; this was ascribed to the autocatalytic thermal degradation during artificial aging. The increase in released heat by 31% was found to be equivalent to evolved NOx gases of 6.2 cm^3/5 g and 2.5 cm^3/1 g for Bergmann-Junk test, and Vacuum stability test respectively. This manuscript shaded the light on a novel approach to quantify evolved NOx gases to heat released with aging time. MDB based on HMX offered balanced ballistic performance,chemical stability, and service life.

Miscibility of light oil and flue gas under thermal action

The miscibility of flue gas and different types of light oils is investigated through slender-tube miscible displacement experiment at high temperature and high pressure.Under the conditions of high temperature and high pressure,the miscible displacement of flue gas and light oil is possible.At the same temperature,there is a linear relationship between oil displacement efficiency and pressure.At the same pressure,the oil displacement efficiency increases gently and then rapidly to more than 90% to achieve miscible displacement with the increase of temperature.The rapid increase of oil displacement efficiency is closely related to the process that the light components of oil transit in phase state due to distillation with the rise of temperature.Moreover,at the same pressure,the lighter the oil,the lower the minimum miscibility temperature between flue gas and oil,which allows easier miscibility and ultimately better performance of thermal miscible flooding by air injection.The miscibility between flue gas and light oil at high temperature and high pressure is more typically characterized by phase transition at high temperature in supercritical state,and it is different from the contact extraction miscibility of CO_(2) under conventional high pressure conditions.

Heat strain in chemical protective clothing in hot-humid environment:Effects of clothing thermal properties

Heat strain experienced by individuals wearing chemical protective clothing(CPC)is severe and dangerous especially in hot-humid environment.The development of material science and interdisciplinary studies including ergonomics,physiology and heat transfer is urgently required for the reduction of heat strain.The aim of this paper was to study the relationship among clothing thermal properties,physiological responses and environmental conditions.Three kinds of CPC were selected.Eight participants wore CPC and walked(4 km/h,two slopes with 5%and 10%)on a treadmill in an environment with(35±0.5)℃ and RH of(60±5)%.Core temperature,mean skin temperature,heart rate,heat storage and tolerance time were recorded and analyzed.Physiological responses were significantly affected by the clothing thermal properties and activity intensity in hot-humid environment.The obtained results can help further development of heat strain model.New materials with lower evaporative resistance and less weight are necessary to release the heat strain in hot-humid environments.

Investigation of feasibility of alkali-cosolvent flooding in heavy oil reservoirs

Cold production is a challenge in the case of heavy oil because of its high viscosity and poor fluidity in reservoir conditions.Alkali-cosolvent-polymer flooding is a type of microemulsion flooding with low costs and possible potential for heavy oil reservoirs.However,the addition of polymer may cause problems with injection in the case of highly viscous oil.Hence,in this study the feasibility of alkali-cosolvent(AC)flooding in heavy oil reservoirs was investigated via several groups of experiments.The interfacial tension between various AC formulations and heavy crude oil was measured to select appropriate formulations.Phase behavior tests were performed to determine the most appropriate formulation and conditions for the generation of a microemulsion.Sandpack flooding experiments were carried out to investigate the displacement efficiency of the selected Ac formulation.The results showed that the interfacial tension between an AC formulation and heavy oil could be reduced to below 1o-3 mN/m but differed greatly between different types of cosolvent.A butanol random polyether series displayed good performance in reducing the water-oil interfacial tension,which made it possible to form a Type Il microemulsion in reservoir conditions.According to the results of the phase behavior tests,the optimal salinity for different formulations with four cosolvent concentrations(0.5 wt%,1 wt%,2 wt%,and 3 wt%)was 4000,8000,14000,and 20000 ppm,respectively.The results of rheological measurements showed that Type Ill microemulsion had a viscosity that was ten times that of water.The results of sandpack flooding experiments showed that,in comparison with waterflooding,the injection of a certain Ac formulation slug could reduce the injection pressure.The pressure gradient during waterflooding and AC flooding was around 870 and 30-57 kPa/m,respectively.With the addition of an AC slug,the displacement efficiency was 30%-50%higher than in the case of waterflooding.

Oxidization characteristics and thermal miscible flooding of high pressure air injection in light oil reservoirs

Physical modeling,numerical simulation and field case analysis were carried out to find out the subsurface thermal oxidation state,thermal oxidation front characteristics and production dynamic characteristics of high pressure air injection thermal oxidation miscible flooding technology.The lighter the composition and the lower the viscosity of the crude oil,the lower the fuel consumption and the combustion temperature are.The thermal oxidation front of light oil and volatile oil can advance stably,and a medium-temperature thermal oxidation stable displacement state can be formed in the light oil reservoir under high pressure conditions.With strong thermal gasification and distillation,light oil and volatile oil are likely to form a single phase zone of gasification and distillation with thermal flue gas at the high-temperature and high-pressure heat front,finally,an air-injection thermal miscible front.In light oil reservoirs,the development process of high-pressure air-injection thermal miscible flooding can be divided into three stages:boosting pressure stage,low gas-oil ratio and high-efficiency stable production stage and high gas-oil ratio production stage.Approximately 70%of crude oil is produced during the boosting pressure stage and low gas-oil ratio high-efficiency and stable production stage.