Thermal-mechanical properties of short carbon fiber reinforced geopolymer matrix composites subjected to thermal load

Short carbon fiber preform reinforced geopolymer composites containing different contents of α-Al2O3 filler （Cr（a-Al2O3）/geopolymer composites） were fabricated, and the effects of heat treatment temperatures up to 1 200 ℃ on the thermal-mechanical properties were studied. The results show that the thermal shrinkage in the direction perpendicular to the lamination of the composites gradually increases with the increase of the heat treatment temperatures from room temperature （25 ℃ ） to 1000 ℃. However, the composites in the direction parallel to the lamination show an expansion behavior. Beyond 1 000℃, in the two directions the composites exhibit a larger degree of shrinkage due to the densification and crystallization. The mechanical properties of the composites show the minimum values in the temperature range from 600 to 800 ℃ as the hydration water of geopolymer matrix is lost. The addition of α-Al2O3 particle filler into the composites clearly increases the onset crystalline temperature of leucite （KAlSi2O6） from the amorphous geopolymer matrix. In addition, the addition of α-Al2O3 particles into the composites can not only help to keep volume stable at high temperatures but also effectively improve the mechanical properties of the composites subjected to thermal load to a certain extent. The main toughening mechanisms of the composites subjected to thermal load are attributed to fiber pulling-out.

Preparation and thermal-mechanical property evaluation of cellulose insulation paper with differing nano-SiC contents

Cellulose insulation paper is the main component of oil-paper insulation systems in oilimmersed transformers.However,the poor thermal conductivity and thermal stability of the cellulose can lead to thermal ageing.It is critical to address this issue by improving the performance of cellulose,nano-SiC-modified cellulose models were established by molecular simulation,while nano-SiC composite papersheets were prepared based on the simulation results,and the effects of different contents of nano-SiC on the papersheets were investigated.Macroscopically,doping nano-SiC particles can enhance the thermal stability of cellulose;compared with the unmodified papersheet,the thermal conductivity and tensile strength of the modified papersheets are increased by 44.3%and 42.8%,respectively.The degree of polymerisation of the modified papersheet decreased more slowly than that of the unmodified papersheet under accelerated thermal ageing,showing that the modified papersheet has better anti-ageing properties.Microscopically,with the addition of nano-SiC,the simulations showed that the mean square displacement of the cellulose decreases dramatically and the distribution of the free volume becomes difficult to disperse,which corresponds to the decrease in porosity in the experiments.As a result,this research provides a way for improving the thermal-mechanical properties of cellulose that has practical application significance.

Effect of Ti Additions on Mechanical and Thermodynamic Properties of W-Ti Alloys: A First-principles Study

The mechanical and thermodynamic properties of W-Ti alloys(including W_(15)Ti_(1),W_(14)Ti_(2),W_(12)Ti_(4) and W_(8)Ti_(8) alloys)were investigated by the first-principles approach based on density functional theory.The results indicate that W-Ti alloys except W_(8)Ti_(8) are thermodynamically stable.The modulus and hardness of W-Ti alloys are smaller than those of pure tungsten and gradually decrease with increasing Ti concentration.However,their B/G ratios and Poisson's ratios exceed those of pure tungsten,suggesting that the introduction of Ti decreases the mechanical strength while enhancing the ductility of W-Ti alloys.The thermal expansion coefficients for W-Ti alloys all surpass those of pure tungsten,indicating that the introduction of titanium exacerbates the thermal expansion behavior of W-Ti alloys.Nevertheless,elevated pressure has the capacity to suppress the thermal expansion tendencies in titanium-doped tungsten alloys.This study offers theoretical insights for the design of nuclear materials by exploring the mechanical and thermodynamic properties of W-Ti alloys.

Effect of a Carbon Fibre-steel Fibre-graphite Conductive Filler on the Electrothermal Properties of Cementitious Materials

Carbon fibre,steel fibre and graphite were used as conductive fillers to prepare cementitious materials with excellent electrothermal properties.The electrically conductive cementitious materials with different volume dosages were analysed through compressive and flexural strength,electrochemical impedance spectroscopy and temperature rise tests.An equivalent circuit model was established to study the electrically conductive heat generation mechanism in the electrically conductive cementitious composites.The results indicate that the mechanical properties of cementitious composite materials with a ternary conductive phase are better than those of pristine cementitious materials because the fibrous filler improves their mechanical properties.However,the incorporation of graphite in the material reduces its strength.Introducing fibrous and point-like conductive phase materials into the cementitious material enhances the overall conductive pathway and considerably reduces the electrical resistance of the cementitious material,enhancing its conductive properties.The volume ratios of carbon fibre,steel fibre and graphite that achieve an optimal complex doping in the cementitious material were 0.35%,0.6%and 6%,respectively.This was determined using the mutation point of each circuit element parameter as the percolation threshold.In addition,at a certain safety voltage,there is a uniform change between the internal and surface temperatures of the conductive cementitious material,and the heating effect in this materialis is considerably better than that in the pristine cementitious material.

Poly(lactic acid)/Poly(butylene adipate-co-terephthalate)films with simultaneous high oxygen barrier and fast degradation properties

Although poly(lactic acid)(PLA)is a good environmentally-friendly bio-degradable polymer which is used to substitute traditional petrochemical-based polymer packaging films,the barrier properties of PLA films are still insufficient for high-barrier packaging applications.In this study,oxygen scavenger hydroxyl-terminated polybutadiene(HTPB)and cobalt salt catalyst were incorporated into the PLA/poly(butylene adipate-co-terephthalate)(PLA/PBAT),followed by melting extrusion and three-layer co-extrusion blown film process to prepare the composite films.The oxygen permeability coefficient of the composite film combined with 6 wt%oxygen scavenger and 0.4 wt%catalyst was decreased significantly from 377.00 cc·mil·m^(-2)·day^(-1)·0.1 MPa^(-1) to 0.98 cc·mil·m^(-2)·day^(-1)·0.1 MPa^(-1),showing a remarkable enhancement of 384.69 times compared with the PLA/PBAT composite film.Meanwhile,the degradation behavior of the composite film was also accelerated,exhibiting a mass loss of nearly 60%of the original mass after seven days of degradation in an alkaline environment,whereas PLA/PBAT composite film only showed a mass loss of 32%.This work has successfully prepared PLA/PBAT composite films with simultaneously improved oxygen barrier property and degradation behavior,which has great potential for high-demanding green chemistry packaging industries,including food,agricultural,and military packaging.

Mechanical Properties of Railway High-strength Manufactured Sand Concrete: Typical Lithology, Stone Powder Content and Strength Grade

In order to achieve the large-scale application of manufactured sand in railway high-strength concrete structure,a series of high-strength manufactured sand concrete(HMC)are prepared by taking the manufactured sand lithology(tuff,limestone,basalt,granite),stone powder content(0,5%,10%,15%)and concrete strength grade(C60,C80,C100)as variables.The evolution of mechanical properties of HMC and the correlation between cubic compressive strength and other mechanical properties are studied.Compared to river sand,manufactured sand enhances the cubic compressive strength,axial compressive strength and elastic modulus of concrete,while its potential microcracks weaken the flexural strength and splitting tensile strength of concrete.Stone powder content displays both positive and negative effects on mechanical properties of HMC,and the stone powder content is suggested to be less than 10%.The empirical formulas between cubic compressive strength and other mechanical properties are proposed.

Molecular simulation study of the microstructures and properties of pyridinium ionic liquid[HPy][BF_(4)]mixed with acetonitrile

The microstructures and thermodynamic properties of mixed systems comprising pyridinium ionic liquid[HPy][BF_(4)]and acetonitrile at different mole fractions were studied using molecular dynamics simulation in this work.The following properties were determined:density,self-diffusion coefficient,excess molar volume,and radial distribution function.The results show that with an increase in the mole fraction of[HPy][BF_(4)],the self-diffusion coefficient decreases.Additionally,the excess molar volume initially decreases,reaches a minimum,and then increases.The rules of radial distribution functions(RDFs)of characteristic atoms are different.With increasing the mole fraction of[HPy][BF_(4)],the first peak of the RDFs of HA1-F decreases,while that of CT6-CT6 rises at first and then decreases.This indicates that the solvent molecules affect the polar and non-polar regions of[HPy][BF_(4)]differently.

Research on the Construction of Intellectual Property System and Optimization of Business Environment in China

With the rapid development of globalization and information technology,intellectual property has been one of the key drivers of economic growth,and the construction of intellectual property system has become an important criterion for measuring the quality of business environment.This article is intended to explore the current status of intellectual property system construction in China,the challenges,and its relationship with the business environment,to propose the corresponding countermeasures and suggestions.The study finds that the legal system of intellectual property in China is gradually improving,and judicial and administrative protection are continuously strengthened.However,the challenges still remain such as frequent infringements,rights hard to protect and insufficient international cooperation.These issues not only affect the legitimate rights and interests of innovation entities,but also for the market fairness and the level of the business environment.Therefore,this article proposes that strengthening the perfection of the intellectual property legal system,enhancing intellectual property services and support capabilities,strengthening international cooperation and exchanges,and accelerating the cultivation of composite talents.It aims to provide theoretical references for the construction of intellectual property system and the optimization of the business environment,promote the high-quality development of economy and enhance the global competitiveness of the country.

Effects of aggregate size distribution and carbon nanotubes on the mechanical properties of cemented gangue backfill samples under true triaxial compression

The mechanical behavior of cemented gangue backfill materials(CGBMs)is closely related to particle size distribution(PSD)of aggregates and properties of cementitious materials.Consequently,the true triaxial compression tests,CT scanning,SEM,and EDS tests were conducted on cemented gangue backfill samples(CGBSs)with various carbon nanotube concentrations(P_(CNT))that satisfied fractal theory for the PSD of aggregates.The mechanical properties,energy dissipations,and failure mechanisms of the CGBSs under true triaxial compression were systematically analyzed.The results indicate that appropriate carbon nanotubes(CNTs)effectively enhance the mechanical properties and energy dissipations of CGBSs through micropore filling and microcrack bridging,and the optimal effect appears at P_(CNT)of 0.08wt%.Taking PSD fractal dimension(D)of 2.500 as an example,compared to that of CGBS without CNT,the peak strength(σ_(p)),axial peak strain(ε_(1,p)),elastic strain energy(Ue),and dissipated energy(U_(d))increased by 12.76%,29.60%,19.05%,and90.39%,respectively.However,excessive CNTs can reduce the mechanical properties of CGBSs due to CNT agglomeration,manifesting a decrease inρ_(p),ε_(1,p),and the volumetric strain increment(Δε_(v))when P_(CNT)increases from 0.08wt%to 0.12wt%.Moreover,the addition of CNTs improved the integrity of CGBS after macroscopic failure,and crack extension in CGBSs appeared in two modes:detour and pass through the aggregates.Theσ_(p)and U_(d)firstly increase and then decrease with increasing D,and porosity shows the opposite trend.Theε_(1,p)andΔε_(v)are negatively correlated with D,and CGBS with D=2.150 has the maximum deformation parameters(ε_(1,p)=0.05079,Δε_(v)=0.01990)due to the frictional slip effect caused by coarse aggregates.With increasing D,the failure modes of CGBSs are sequentially manifested as oblique shear failure,"Y-shaped"shear failure,and conjugate shear failure.

Processing,microstructure,and mechanical properties of wire arc additively-manufactured AZ91 magnesium alloy using cold arc process

Thin walls of an AZ91 magnesium alloy with fine equiaxed grains were fabricated via cold arc-based wire arc additive manufacturing(CA-WAAM),and the droplet transfer behaviours,microstructures,and mechanical properties were investigated.The results showed that the cold arc process reduced splashing at the moment of liquid bridge breakage and effectively shortened the droplet transfer period.The microstructures of the deposited samples exhibited layered characteristics with alternating distributions of coarse and fine grains.During layer-by-layer deposition,the β-phase precipitated and grew preferentially along grain boundaries,while the fineη-Al_(8)Mn_(5)phase was dispersed in the α-Mg matrix.The mechanical properties of the CA-WAAM deposited sample showed isotropic characteristics.The ultimate tensile strength and elongation in the building direction(BD)were 282.7 MPa and 14.2%,respectively.The microhardness values of the deposited parts were relatively uniform,with an average value of HV 69.6.

Synthesis,structure,and magnetic property of a cobalt(Ⅱ)complex based on pyridyl⁃substituted imino nitroxide radical

A new cobalt(Ⅱ)-radical complex:[Co(im4-py)_(2)(PNB)_(2)](im4-py=2-(4'-pyridyl)-4,4,5,5-tetramethylimidazole-1-oxyl,HPNB=p-nitrobenzoic acid)has been synthesized and characterized by X-ray diffraction analysis,elemental analysis,IR,and magnetic properties.X-ray diffraction analysis shows that the complex exists as mononuclear molecules and Co(Ⅱ)ion is four-coordinated with two radicals and two PNB-ligands.The magnetic susceptibility study indicates the complex exhibits weak ferromagnetic interactions between cobalt(Ⅱ)and im4-py radical.The magnetic property is explained by the magnetic and structure exchange mechanism.CCDC:976028.

Characterization and correlation of engineering properties with microstructure in peanuts:A microscopic to macroscopic analysis

Peanut varieties are diverse globally,with their characters and nutrition determining the product quality.However,the comparative analysis and statistical analysis of key quality indicators for peanut kernels across the world remains relatively limited,impeding the comprehensive evaluation of peanut quality and hindering the industry development on a global scale.This study aimed to compare and analyze the apparent morphology,microstructure,single-cell structure,engineering and mechanical properties,as well as major nutrient contents of peanut kernels from 10 different cultivars representing major peanut-producing countries.The surface and cross-section microstructure of the peanut kernels exhibited a dense“blocky”appearance with a distinct cellular structure.The lipid droplets were predominantly spherical with a regular distribution within the cells.The single-cell structure of the kernels from these 10 peanut cultivars demonstrated varying morphologies and dimensions,which exhibited correlations with their mechanical and engineering properties.Furthermore,the mass loss versus temperature profiles of the peanut kernels revealed five distinct stages,corresponding to moisture loss,volatile loss,protein denaturation,and the degradation of various biomacromolecules.Variations were also observed in the lipid,protein,and sucrose contents,texture,bulk density,true density,porosity,geometric mean diameter,and sphericity among the diferent peanut varieties.This study establishes relationships and correlations among microstructure,engineering properties,and nutritional composition of commonly grown peanut varieties in major peanut-processing countries.The findings provide valuable insights into peanut quality evaluation,empowering the peanut industry to enhance their processing and product development efforts.

Corrosion resistance and antibacterial properties of Ti−3Cu alloy prepared by selective laser melting

The corrosion resistance and antibacterial properties of Ti−3Cu alloy prepared by selective laser melting were evaluated using electrochemical experiments and a variety of antibacterial characterization.It is found that the charge transfer resistance of Ti−3Cu alloy was 4.89×10^(5)Ω∙cm^(2),which was doubled the data obtained by CP-Ti alloy.The antibacterial rates of Ti−3Cu alloy against S.mutans and P.gingivalis were 45.0%and 54.5%.And the antibacterial rates increased with the prolongation of cultivation time,reaching up to 62.8%and 68.6%,respectively.The in-situ nano Ti_(2)Cu precipitates were homogeneously distributed in the matrix of the Ti−3Cu alloy,which was the key reason of increasing the corrosion resistance.Additionally,the microscale electric fields between theα-Ti matrix and the Ti_(2)Cu was responsible for the enhancement of the antibacterial properties.

Innovative dispersion techniques of graphene nanoplatelets(GNPs)through mechanical stirring and ultrasonication:Impact on morphological,mechanical,and thermal properties of epoxy nanocomposites

Graphene nanoplatelets(GNPs)have attracted tremendous interest due to their unique properties and bonding capabilities.This study focuses on the effect of GNP dispersion on the mechanical,thermal,and morphological behavior of GNP/epoxy nanocomposites.This study aims to understand how the dispersion of GNPs affects the properties of epoxy nanocomposite and to identify the best dispersion approach for improving mechanical performance.A solvent mixing technique that includes mechanical stirring and ultrasonication was used for producing the nanocomposites.Fourier transform infrared spectroscopy was used to investigate the interaction between GNPs and the epoxy matrix.The measurements of density and moisture content were used to confirm that GNPs were successfully incorporated into the nanocomposite.The findings showed that GNPs are successfully dispersed in the epoxy matrix by combining mechanical stirring and ultrasonication in a single step,producing well-dispersed nanocomposites with improved mechanical properties.Particularly,the nanocomposites at a low GNP loading of 0.1 wt%,demonstrate superior mechanical strength,as shown by increased tensile properties,including improved Young's modulus(1.86 GPa),strength(57.31 MPa),and elongation at break(4.98).The nanocomposite with 0.25 wt%GNP loading performs better,according to the viscoelastic analysis and flexural properties(113.18 MPa).Except for the nanocomposite with a 0.5 wt%GNP loading,which has a higher thermal breakdown temperature,the thermal characteristics do not significantly alter.The effective dispersion of GNPs in the epoxy matrix and low agglomeration is confirmed by the morphological characterization.The findings help with filler selection and identifying the best dispersion approach,which improves mechanical performance.The effective integration of GNPs and their interaction with the epoxy matrix provides the doorway for additional investigation and the development of sophisticated nanocomposites.In fields like aerospace,automotive,and electronics where higher mechanical performance and functionality are required,GNPs'improved mechanical properties and successful dispersion present exciting potential.

Stable structures and properties of Ru_(2)Al_(5)

Novel ordered intermetallic compounds have stimulated much interest.Ru–Al alloys are a prominent class of hightemperature structural materials,but the experimentally reported crystal structure of the intermetallic Ru_(2)Al_(5) phase remains elusive and debatable.To resolve this controversy,we extensively explored the crystal structures of Ru_(2)Al_(5) using first-principles calculations combined with crystal structure prediction technique.Among the calculated x-ray diffraction patterns and lattice parameters of five candidate Ru2Al5structures,those of the orthorhombic Pmmn structure best aligned with recent experimental results.The structural stabilities of the five Ru_(2)Al_(5)structures were confirmed through formation energy,elastic constants,and phonon spectrum calculations.We also comprehensively analyzed the mechanical and electronic properties of the five candidates.This work can guide the exploration of novel ordered intermetallic compounds in Ru–Al alloys.

Modeling Thermophysical Properties of Hybrid Nanofluids:Foundational Research for Future Photovoltaic Thermal Applications

The primary objective of this study is to develop an innovative theoretical model to accurately predict the thermophysicalproperties of hybrid nanofluids designed to enhance cooling in solar panel applications.This researchlays the groundwork for our future studies,which will focus on photovoltaic thermal applications.These nanofluidsconsist of water and nanoparticles of alumina(Al_(2)O_(3)),titanium dioxide(TiO_(2)),and copper(Cu),exploringvolumetric concentrations ranging from 0%to 4%for each type of nanoparticle,and up to 10%for total mixtures.The developed model accounts for complex interactions between the nanoparticles and the base fluid,as well assynergistic effects resulting from the coexistence of different nanoparticles.Detailed simulations have shownexceptional agreement with experimental results,reinforcing the credibility of our approach in accurately capturingthe thermophysical behavior of these hybrid nanofluids.Based on these results,our study proposes significantadvancements in the design and optimization of nanofluids for cooling applications in solar panels.These developmentsare crucial for improving the efficiency of solar installations by mitigating overheating effects,providinga solid foundation for practical applications in this rapidly evolving field.

Mechanical properties and flow stress constitutive relationship of Ti–6Al–4V alloy with equiaxed microstructure at cryogenic temperatures

This paper investigates the uniaxial tensile mechanical properties and flow behavior of Ti-6Al-4V alloys with equiaxed microstructure at cryogenic temperatures ranging from 77 K to298 K and strain rates from 10^(-4)/s to 10^(-2)/s.Scanning electron microscopy is utilized to analyze the fracture morphology,aiming to reveal the fracture behavior at various temperatures.The applicability of the Zener-Hollomon parameter and the Johnson-Cook model in describing the flow stress of Ti-6Al-4V at cryogenic temperatures is analyzed.Moreover,a constitutive relationship modeling method based on the variational recurrent networks is proposed.Mechanical test results show a significant increase in the strength of equiaxed Ti-6Al-4V alloy under cryogenic conditions while the plastic deformation process is shortened.However,the fracture analysis indicates that even at 77 K,the fracture process is still dominated by ductile fracture,and brittle fracture does not occur within the range of 77 K to 298 K.The fitting results validate the performance of the Zener-Hollomon parameter and the Johnson-Cook model in describing the deformation flow stress of Ti-6Al-4V alloy at cryogenic temperatures.The results also indicate that the proposed constitutive relationship modeling method based on the variational recurrent network performs better,making it a potential method for widespread applications.

Achieving further refinement of grain structure and improvement of mechanical properties in Al-12Si-4Cu-2Ni-1Mg alloy by Al-Ti-C-B master alloy addition and deep cryogenic treatment

Near-eutectic Al-Si alloys are widely used in automotive manufacturing due to their superior wear resistance and high temperature performance.Because of high Si content,the grain refinement of near-eutectic Al-Si alloy has been a problem for many years.In this study,the effect of deep cryogenic treatment(DCT)on the microstructure and mechanical properties of Al-12Si-4Cu-2Ni-Mg alloy with addition of Al-Ti-C-B master alloy was fully investigated.Results show that the average grain size of the alloy is greatly reduced from 0.92 mm to 0.50 mm,and the eutectic Si and Al7Cu4Ni precipitates are spheroidized and refined in Al-12Si-4Cu-2Ni-Mg after DCT for 24 h and aging treatment.Thereby these changes of microstructures result in a significant increment of about 22.5%in elongation and a slight enhancement of about 6.8%in tensile strength.Moreover,the refinement of microstructure also significantly improves the fatigue life of the alloy.

Positive effect of Mo on mechanical properties of a Ni-42W-10Co-xMo medium heavy alloy

In this study,a novel Ni-W-Co-Mo medium heavy alloy(MHA)was designed to improve its mechanical strength via Mo doping.In the Ni-42W-10Co-x Mo alloy series,where x represents the weight percent of Mo and varies between 0,1,2,5,and 10,the microstructure transitions from a dendritic structure to a hypo-eutectic structure as the Mo content increases from 0 to 5wt.%.Moreover,as the Mo content increases from 0 to 10wt.%,the distribution of theμ-phase shifts from being individually dispersed to forming aggregates,and its volume fraction rises from 0.5%to 7.9%.Notably,theμ-phase evolves into an eutectic microstructure,which helps in minimizing the segregation of elements.This change is accompanied by a substantial enhancement in mechanical properties;specifically,the compressive yield strength at room temperature increases from 350 MPa to 646 MPa,indicating a significant 85%increase.Similarly,the microhardness increases from 230 HV to 304 HV.Molecular dynamics simulations further reveal that the strengthening mechanism of Ni-42W-10Co-x Mo alloys is Mo-induced solid solution strengthening and precipitation strengthening.

Obtaining Electromagnetic Properties of Multi-Type Media in Realistic Environments:State-of-the-Art and Prospects

To meet the requirements of electromagnetic(EM)theory and applied physics,this study presents an overview of the state-of-the-art research on obtaining the EM properties of media and points out potential solutions that can break through the bottlenecks of current methods.Firstly,based on the survey of three mainstream approaches for acquiring EM properties of media,we identify the difficulties when implementing them in realistic environments.With a focus on addressing these problems and challenges,we propose a novel paradigm for obtaining the EM properties of multi-type media in realistic environments.Particularly,within this paradigm,we describe the implementation approach of the key technology,namely“multipath extraction using heterogeneous wave propagation data in multi-spectrum cases”.Finally,the latest measurement and simulation results show that the EM properties of multi-type media in realistic environments can be precisely and efficiently acquired by the methodology proposed in this study.