Thermodynamic optimization for a quantum thermoacoustic refrigeration micro-cycle

A model of quantum thermoacoustic refrigeration micro-cycle(QTARMC)is established in which heat leakage is considered.A single particle contained in a one-dimensional harmonic potential well is studied,and the system consists of countless replicas.Each particle is confined in its own potential well,whose occupation probabilities can be expressed by the thermal equilibrium Gibbs distributions.Based on the Schrodinger equation,the expressions of coefficient of performance(COP)and cooling rate for the refrigerator are obtained.Effects of heat leakage on the optimal performance are discussed.The optimal performance region of the refrigeration cycle is obtained by the using ofΩobjective function.The results obtained can enrich the thermoacoustic theory and expand the application of quantum thermodynamics.

The Performance of the First Pilot Thermoacoustic Refrigerator

The simple goal of this work is constructing a cheap, demonstrative model of a thermoacoustic refrigerator. To this end, the author succeeded in designing, building and testing the first pilot thermoacoustic refrigeration in Jordan basing on the theory of using sound waves as a coolant. The pilot thermoacoustic refrigerator was built from inexpensive and readily available parts in Mutah University, Jordan. The thermoacoustic refrigerator was operated for several hours. Consequentially, this experiment proved that thermoacoustic refrigerators were technically possible. Additionally, this experiment did yield some findings regarding the efficiency of thermoacoustic refrigeration. On other hand, solid flow CFD software was used to simulate the performance of thermoacoustic refrigerator especially the temperature and velocity inside the refrigerator. In general, very good agreement was deduced.

Performance Analysis of Thermoacoustic Refrigerator of 10 W Cooling Power Made up of Poly-Vinyl-Chloride for Different Parallel Plate Stacks by Using Helium as a Working Fluid

Refrigerants are usually provided in the conventional refrigeration system although the refrigerants produce Chlorofluorocarbons(CFCs)and Hydro-chlorofluorocarbons(HCFCs),which are hazardous to the environment.However,these disadvantages can be overcome by using air or inert gas in the thermoacoustic refrigeration system.In the present experimental work,helium is used as a working gas with an operating pressure range of 0.2 MPa to 1.0 MPa in order to study the performance of thermoacoustic refrigerator(TAR)which is fabricated using Poly-Vinyl-Chloride(PVC).The parallel plate stacks with different porosity ratios have been considered to study the performance of TAR.The temperature difference between the hot and cold heat exchanger and acoustic dynamic pressure were recorded by using Bruel and Kjaer data acquisition system under different operating conditions.The effect of different operating parameters such as operating frequency(200 Hz to 600 Hz),cooling load(2 W to 10 W)and drive ratio(0.6%to 1.6%)have also been considered to study the performance of TAR.The TAR also modeled in DeltaEC software and the results are compared with the experimental outcomes and found to be in good agreement.The experimental results show that-2.1℃is the lowest temperature measured at cold heat exchanger by achieving the highest temperature difference of about 32.9℃.An improvement is around 36%as compared to that of previous experiments that used aluminium TAR.The highest Coefficient of Performance(COP)and the Relative Coefficient of Performance(COPR)are found to be 2.024 and 0.217,respectively.

Optimization of thermoacoustic refrigerator using response surface methodology

Thermoacoustic refrigerator （TAR） converts acoustic waves into heat without any moving parts. The study presented here aims to optimize the parameters like frequency, stack position, stack length, and plate spacing involving in designing TAR using the Response Surface Methodology （RSM）. A mathematical model is developed using the RSM based on the results obtained from DeltaEC software. For desired temperature difference of 40 K, optimized parameters suggested by the RSM are the frequency 254 Hz, stack position 0.108 m, stack length 0.08 m, and plate spacing 0.0005 m. The experiments were conducted with optimized parameters and simulations were performed using the Design Environment for Low-amplitude ThermoAcoustic Energy Conversion （DeltaEC） which showed similar results.