Progress in preparation of AlN-reinforced magnesium matrix composites:A review

As a ceramic material,AlN has very good thermophysical and mechanical properties.In addition,AlN is an effective refining agent for Mg alloys because it has a lattice constant similar to that of Mg.Therefore,AlN is an ideal reinforcement for magnesium matrix composites(MMCs),and is attracting increasing attention.This review addresses the development of preparation technologies for AlN-reinforced Mg matrix composites.The mainstream preparation techniques include stir casting,melt infiltration,powder metallurgy,and in-situ methods.In addition,the advantages and disadvantages of these techniques are analyzed in depth,and it is pointed out that the next direction for the preparation of high-performance AlN-reinforced MMCs is less aluminization and multiple technologies integration.

Functional thermal fluids and their applications in battery thermal management:A comprehensive review

With the increasing requirements for fast charging and discharging,higher requirements have been put forward for the thermal management of power batteries.Therefore,there is an urgent need to develop efficient heat transfer fluids.As a new type of heat transfer fluids,functional thermal fluids mainly includ-ing nanofluids(NFs)and phase change fluids(PCFs),have the advantages of high heat carrying density,high heat transfer rate,and broad operational temperature range.However,challenges that hinder their practical applications remain.In this paper,we firstly overview the classification,thermophysical prop-erties,drawbacks,and corresponding modifications of functional thermal fluids.For NFs,the high ther-mal conductivity and high convective heat transfer performance were mainly elaborated,while the stability and viscosity issues were also analyzed.And then for PCFs,the high heat carrying density was mainly elaborated,while the problems of supercooling,stability,and viscosity were also analyzed.On this basis,the composite fluids combined NFs and PCFs technology,has been summarized.Furthermore,the thermal properties of traditional fluids,NFs,PCFs,and composite fluids are compared,which proves that functional thermal fluids are a good choice to replace traditional fluids as coolants.Then,battery thermal management system(BTMS)based on functional thermal fluids is summarized in detail,and the thermal management effects and pump consumption are compared with that of water-based BTMS.Finally,the current technical challenges that parameters optimization of functional thermal fluids and structures optimization of BTMS systematically are presented.In the future,it is necessary to pay more attention to using machine learning to predict thermophysical properties of functional thermal fluids and their applications for BTMS under actual vehicle conditions.

Production and Characterization of a Composite Based on Plaster and Juncus Maritimus Plant Fibers

Nowadays,materials with a limited impact on the environment are required in the construction sector.Considering the interesting properties of natural elements such as natural fibers,it seems advantageous to use them to reinforce materials while protecting the environment and guaranteeing economic gain.Along these lines,this research was devoted to studying the effect of untreated natural fibers extracted from the Juncus maritimus plant(from Southern Morocco)on plaster.First,the effect of the percentage of added fibers on the fluidity of the plaster was evaluated by means of the Marsh’s cone method,that is,by measuring the time taken by a known volume of plaster to flow from a cone through a short tube.Then,the highly porous microstructure of the plaster was observed using a scanning electron microscope(SEM).The diffractogram of Juncus maritimus fibers was built by means of a X-ray diffraction(XRD)method.The values obtained for the wet thermal conductivity of the composites decreased from 0.4853 W/m.K for the reference specimen to 0.4324 W/m K for a fiber volume content of 40%.The densities were calculated to determine the lightness of each composite.The mechanical strengths[flexural and compressive]were evaluated for different percentages of rush fibers.The addition of 20%volume fiber was found to improve the flexural strength to 3.63 MPa compared to the sample without fiber(3.36 MPa),thereby ensuring good toughness of the considered material.Nevertheless,a reduction in compressive strength was observed,due to the poor adhesion between the fibers and the plaster matrix.

Simultaneous Identification of Thermophysical Properties of Semitransparent Media Using a Hybrid Model Based on Artificial Neural Network and Evolutionary Algorithm

A hybrid identification model based on multilayer artificial neural networks(ANNs) and particle swarm optimization(PSO) algorithm is developed to improve the simultaneous identification efficiency of thermal conductivity and effective absorption coefficient of semitransparent materials.For the direct model,the spherical harmonic method and the finite volume method are used to solve the coupled conduction-radiation heat transfer problem in an absorbing,emitting,and non-scattering 2D axisymmetric gray medium in the background of laser flash method.For the identification part,firstly,the temperature field and the incident radiation field in different positions are chosen as observables.Then,a traditional identification model based on PSO algorithm is established.Finally,multilayer ANNs are built to fit and replace the direct model in the traditional identification model to speed up the identification process.The results show that compared with the traditional identification model,the time cost of the hybrid identification model is reduced by about 1 000 times.Besides,the hybrid identification model remains a high level of accuracy even with measurement errors.

Thermophysical Characterization of Local Materials from a Locality in Chad for Use in Eco-Building

With the aim of enhancing the value of local building materials, the subject of this paper is a thermophysical study of natural Chadian clay from the eastern region of Chad, “Abeche”. Samples were taken from a brickwork in Abeche from a depth of 1 m, then using a clay brick-making press, 4 × 5 × 8 cm3 clay test tubes were made with 2%, 4%, 6% and 8% cow dung, and a 100% clay sample was used as a control. These samples underwent thermophysical characterization using the hot-wire method with a hot-plane option, yielding results that could improve thermophysical performance. The thermal conductivity of the test sample is in the order of 0.715 to 0.420 W/m. K, at 8% for cow dung, so the addition of cow dung as a percentage in the clay matrix enabled us to obtain various satisfactory thermal parameters.

Influence of Temperature-Dependent Thermophysical Properties of TiO2-SiO2-ZnO-Fe2O3/PAO Tetra-Hybrid Nanofluid along a Vertical Porous Surface with Suction

The significance of the thermophysical properties of Tetra hybrid nanofluid in enhancing heat transmission in various applications like heat exchangers, automobiles, and solar storage cannot be overstated. These features can be tampered with when nanoparticles are been introduced into the base fluid to produce an improved heat carrier fluid for the system. This study investigates the impact of temperature-dependent properties on the movement of TiO2-SiO2-ZnO-Fe2O3/PAO Tetra hybrid nanofluid along a vertical porous surface with suction. The system of governing Partial Differential Equations (PDEs) was formulated and transformed into the system of coupled nonlinear third-order Ordinary Differential Equations (ODEs) by similarity techniques. The resulting ODEs were solved numerically using the shooting method and fourth order Runge-Kutta method with the aid of Maple 18.0 software. Using numerical and statistical methods, the study analyzes velocity, temperature profiles, skin friction coefficient, and Nusselt number. It was found that as the variable thermal conductivity parameter upsurges both the skin friction coefficient and Nusselt number intensify at the rate of 0.011697519 and 8.043581616 respectively. This study underscores the vital role of Tetra hybrid nanofluid’s thermophysical properties in improving heat transmission for diverse appli cations. By manipulating nanoparticles within the base fluid, the heat carrier fluid’s efficiency can be enhanced, critical for industries like automotive and enewable energy. These insights inform the design of more efficient heat exchange systems, advancing sustainability and performance in real-world scenarios.

Experimental Evaluation of Thermal Conductivity and Other Thermophysical Properties of Nanofluids Based on Functionalized (-OH) Mwcnt Nanoparticles Dispersed in Distilled Water

A possible way to increase thermal conductivity of working fluids, while keeping pressure drop at acceptable levels, is through nanofluids. Nanofluids are nano-sized particles dispersed in conventional working fluids. A great number of materials have potential to be used in nanoparticles production and then in nanofluids;one of them is Multi-Walled Carbon Nano Tubes (MWCNT). They have thermal conductivity around 3000 W/mK while other materials used as nanoparticles like CuO have thermal conductivity of 76.5 W/mK. Due to this fact, MWCNT nanoparticles have potential to be used in nanofluids production, aiming to increase heat transfer rate in energy systems. In this context, the main goal of this paper is to evaluate from the synthesis to the experimental measurement of thermal conductivity of nanofluid samples based on functionalized (-OH) MWCNT nanoparticles. They will be analyzed nanoparticles with different functionalization degrees (4% wt, 6% wt, and 9% wt). In addition, it will be quantified other thermophysical properties (dynamic viscosity, specific heat and specific mass) of the synthetized nanofluids. So, the present work can contribute with experimental data that will help researches in the study and development of MWCNT nanofluids. According to the results, the maximum increment obtained in thermal conductivity was 10.65% in relation to the base fluid (water).

Analysis on Velocity Characteristics of Cavitation Flow Around Hydrofoil

The time-averaged velocity distributions in flows around a hydronautics hydrofoil were measured by using a digital particle image velocimeter(DPIV) system.The results show that the velocity distribution in the whole flow field depends on the development of cavitation structures with the decreasing of cavitation number.The high-fluctuation region with lower velocity relates to the cavitation area.The lowest velocity distribution in the cavity core becomes more uniform,and its influence becomes smaller gradually as moving to downstream.The main-stream velocity distribution is even,then fluctuate and even at last.In the supercavitation stage,the fluid velocity in the cavitation region,corresponding to the front of the hydrofoil's suction surface,has a distribution close to the main stream,while the fluid velocity in other cavitation area is lower.

Calculation and Analysis for Temperature Field of Tank Track and Wheels

To know the temperature status of track and wheels on tank,the finite element calculation of temperature field was implemented with ANSYS software.The detailed temperature distributions for road wheel,drive wheel,idle wheel and track loop were obtained.The effect of factors,such as tank speed,environment temperature,sun radiant energy,ground deformation resistant and tank load,on the temperature of road wheel was studied.The sensitivity analysis shows that the effect of tank load on the temperature is the most,and the effect of ground deformation resistant is the least.The temperature testing device for road wheel on tank was developed to perform the experiments in real time.The calculated temperatures are in accord well with the experimental values.

About Thermophysical Properties of the Hollow Cathode

One of the problems specifying erosion of the cathode is to establish the conditions giving rise to a diffuse or contracted arc-cathode interaction independent of its type and construction. In various works transition from one interaction mode to another was related to the value of a critical current, a pressure range etc. A criterion related to a thermal state of the cathode has greater generality, since it essentially varies with the arc-cathode contacts. First of all it relates to emission cooling relationship with the other components of the cathode heat flux. It is established that in the contracted sport the emission cooling exceeds the radiation one by a factor of 50 to 100. For a diffuse contact the emission and radiation components of the cathode heat loss become comparable. A cathode thermal state is the effect of the arc confined head load. Under these conditions temperature in the arc-cathode contact area depends on the geometrical dimensions of the electrode. The effect of electrode thickness on temperature is indefinite and depends on the thermophysical properties of the electrode, i.e. thermal conductance and its surface blackness.

Study on Graphene Oxide Modified Inorganic Phase Change Materials and Their Packaging Behavior

We prepared the nano-inorganic phase-change ＂alloy＂ materials through the modification of Na2SO4·10H2O using Na2HPO4·12H2O and GO nano-nucleating agent, and further investigated their thermophysical properties such as melting/solidification temperatures and enthalpies via differential scanning calorimetry. When the weight ratio of Na2SO4·10H2O and Na2HPO4·12H2O was 8：2 and the weight ratio of graphene oxide was 0.5% of phase change material, the phase change ＂alloy＂ material showed excellent performances, specifically, the melting temperature and latent heat were found to be 22 ℃ and 190 J/g with a degree of subcooling decreased from 8.6℃ to 2.1℃. In order to extend the application of the phase change ＂alloy＂ material to building energy saving field, it was adsorbed on expanded glass beads under vacuum and further covered with diatomite. When the adsorption rate of EGB（volume） and PCAM（weight） was 2.5：1, the particle size of diatomaceous earth was found to be 3.6μm, while the best packaging result was obtained with the melting temperature and latent heat being 21℃ and 135 J/g, and no leakage was observed.

Present Terrestrial Heat Flow Measurements of the Geothermal Fields in the Chagan Sag of the YingenEjinaqi Basin,Inner Mongolia,China

Owing to the lack o f terrestrial heat flow data, studying lithospheric thermal structure and geodynamics of the Yingen-Ejinaqi Basin in Inner Mongolia is limited. In this paper, the terrestrial heat flow o f the Chagan sag in the YingenEjinaqi Basin were calculated by 193 system steady-state temperature measurements of 4 wells, and newly measuring 62 rock thermal conductivity and 20 heat production rate data on basis o f the original 107 rock thermal conductivity and 70 heat production data. The results show that the average thermal conductivity and heat production rate are 2.11 ±0.28 W/(m.K) and2.42±0.25 nW/m^3 in the Lower Cretaceous o f the Chagan sag. The average geothermal gradient from the Lower Suhongtu 2 Formation to the Suhongtu 1 Fonnation is 37.6 °C/km, and that o f the Bayingebi 2 Formation is 27.4 °C/km. Meanwhile, the average terrestrial heat flow in the Chagan sag is 70.6 mW/m^2. On the above results, it is clear that there is an obvious negative correlation between the thermal conductivity o f the stratum and its geothermal gradient. Moreover, it reveals that there is a geothermal state between tectonically stable and active areas. This work may provide geothermal parameters for further research o f lithospheric thermal structure and geodynamics in the Chagan sag.

Thermophysical properties of the Ni-based alloy Nimonic 80A up to 2400 K

Nimonic 80A is a nickel-chromium alloy which is strengthened by additions of titanium and aluminium. The alloy is used for high temperature, high strength applications. Wire shaped Nimonic 80A samples are resistively volume heated as part of a fast capacitor discharge circuit. Time resolved measurements with sub-μs resolution of current through the specimen are performed with a Pearson probe, voltage drop across the specimen is measured with knife-edge contacts and ohmic voltage dividers and the radiance temperature of the sample with a pyrometer. These measurements allow to determine heat of fusion as well as heat capacity and electrical resistivity at initial geometry of Nimonic 80A as a function of temperature in the solid and in the liquid phase up to 2400 K.

Structural and thermophysical properties characterization of continuously reinforced cast Al matrix composite

In this work the process of manufacturing a continuously reinforced cast Al matrix composite and its properties are presented. The described technology permits obtaining a structural material of competitive properties compared to either heat treatable aluminum alloys or polymer composites for several types of applications. The examined thermophysical properties and structural characterization, including material anisotropy, coupled with the results of previous measurements of the mechanical properties of both Al2O3 reinforcing filaments and metallic prepregs have proven the high quality of this material and the possibility of its operation under special loading modes and environmental conditions. Microscopic examinations (LM, SEM) were carried out to reveal the range of morphological homogeneity of the microstructure, the anisotropy of the filament band distribution, and simultaneously the adhesive behavior of the metal/fbier interface. The 3D morphology of the chosen microstructure components was revealed by computed tomography. The obtained results indicate that special properties of the examined prepreg materials have been strongly influenced, on the one hand, by the geometry of its internal microstructure, i.e. spatial distribution and volume fraction of the Al2O3 reinforcing filaments and, on the other hand, by a very good compatibility obtained between the individual metal prepreg components.

Study on the influencing factors of rock-soil thermophysical parameters in shallow geothermal energy

Thermophysical parameters are the main parameters affecting the utilization efficiency of shallow geothermal energy. Based on the research and evaluation data of shallow geothermal energy in capital cities of China, this paper analyzes the differences between two testing methods and finds that data measured in in-situ thermal conductivity test is closer to the actual utilization. This paper analyzes the influencing factors of thermophysical parameters from lithology, density, moisture content and porosity: The thermal conductivity coefficient of bedrock is generally higher than Quaternary system loose bed soil; as for the coefficient of bedrock, dolomite, shale and granite are higher while gabbro, sandstone and mudstone are lower; as for the coefficient of loose bed, pebble and gravel are higher while clay and silt are lower. As the particle size of sand decreases, the thermal conductivity coefficient declines accordingly. The thermal conductivity coefficient increases linearly with growing density and decreases in logarithm with growing moisture content as well as porosity; specific heat capacity decreases in logarithm with growing density, increases in power exponent with growing moisture content and decreases linearly with growing porosity. The thermal conductivity coefficient is high when hydrodynamic condition is good and vice versa. The conclusions of this paper have guiding significance for the research, evaluation and development of shallow geothermal energy in other areas.

Effect of thermophysical property and coating thickness on microstructure and characteristics of a casting

A new improved investment casting technology （IC） has been presented and compared with the existing IC technology such as lost foam casting （LFC）. The effect of thermophysical property and coating thickness on casting solidification temperature field, microstructure and hardness has been investigated. The results show that the solidification rate decreases inversely with the coating thickness when the coating contains silica sol, zircon powder, mullite powder and defoaming agent. In contrast, the solid cooling rate increases as the coating thickness increases. However, the solidification rate and solid cooling rate of the casting produced by the existing IC and the improved IC are very similar when the coating thickness is 5 mm, so the microstructure and hardness of a container corner fitting produced by the improved IC and the existing IC are similar. The linear regression equation for the grain size （d） and cooling rate （v） of the castings is d= -0.41v＋206.1. The linear regression equation for the content of pearlite （w） and solid cooling rate （t） is w=1.79t ＋ 6.71. The new improved IC can greatly simplify the process and decrease the cost of production compared with the existing IC. Contrasting with LI=C, container corner fittings produced by the new improved IC have fewer defects and better properties. It was also found that the desired microstructure and properties can be obtained by changing the thermophysical property and thickness of the coating.

Development of thermophysical calculator for stainless steel casting alloys by using CALPHAD approach

The calculation of thermophysical properties of stainless steel castings and its application to casting simulation is discussed. It is considered that accurate thermophysical properties of the casting alloys are necessary for the valid simulation of the casting processes. Although previous thermophysical calculation software requires a specific knowledge of thermodynamics, the calculation method proposed in the present study does not require any special knowledge of thermodynamics, but only the information of compositions of the alloy. The proposed calculator is based on the CALPHAD approach for modeling of multi-component alloys, especially in stainless steels. The calculator proposed in the present study can calculate thermophysical properties of eight-component systems on an iron base alloy(Fe-C-Si-Cr-Mn-Ni-Cu-Mo), and several Korean standard stainless steel alloys were calculated and discussed. The calculator can evaluate the thermophysical properties of the alloys such as density, heat capacity, enthalpy, latent heat, etc, based on full Gibbs energy for each phase. It is expected the proposed method can help casting experts to devise the casting design and its process easily in the field of not only stainless steels but also other alloy systems such as aluminum, copper, zinc, etc.

Al_(2)O_(3) andγAl_(2)O_(3) Nanomaterials Based Nanofluid Models with Surface Diffusion:Applications for Thermal Performance in Multiple Engineering Systems and Industries

Thermal transport investigation in colloidal suspensions is taking a significant research direction.The applications of these fluids are found in various industries,engineering,aerodynamics,mechanical engineering and medical sciences etc.A huge amount of thermal transport is essential in the operation of various industrial production processes.It is a fact that conventional liquids have lower thermal transport characteristics as compared to colloidal suspensions.The colloidal suspensions have high thermal performance due to the thermophysical attributes of the nanoparticles and the host liquid.Therefore,researchers focused on the analysis of the heat transport in nanofluids under diverse circumstances.As such,the colloidal analysis of H_(2)O composed byγAl_(2)O_(3)and Al_(2)O_(3)is conducted over an elastic cylinder.The governing flow models ofγAl_(2)O_(3)/H_(2)O and Al_(2)O_(3)/H_(2)O is reduced in the dimensionless form by adopting the described similarity transforms.The colloidal models are handled by implementing the suitable numerical technique and provided the results for the velocity,temperature and local thermal performance rate against the multiple flow parameters.From the presented results,it is shown that the velocity of Al_(2)O_(3)–H_(2)O increases promptly against a high Reynolds number and it decreases for high-volume fraction.The significant contribution of the volumetric fraction is examined for thermal enhancement of nanofluids.The temperature of Al_(2)O_(3)–H_(2)O andγAl_(2)O_(3)–H_(2)O significantly increases against a higherϕ.Most importantly,the analysis shows thatγAl_(2)O_(3)–H_(2)O has a high local thermal performance rate compared to Al_(2)O_(3)–H_(2)O.Therefore,it is concluded thatγAl_(2)O_(3)–H_(2)O is a better heat transfer fluid and is suitable for industrial and technological uses.

Second Law Analysis of Magneto Radiative GO-MoS_(2)/H_(2)O–(CH_(2)OH)_(2) Hybrid Nanofluid

Entropy Generation Optimization(EGO)attained huge interest of scientists and researchers due to its numerous applications comprised in mechanical engineering,air conditioners,heat engines,thermal machines,heat exchange,refrigerators,heat pumps and substance mixing etc.Therefore,the study of radiative hybrid nanofluid(GO-MoS_(2)/C_(2)H_(6)O_(2)–H_(2)O)and the conventional nanofluid(MoS_(2)/C_(2)H_(6)O_(2)–H_(2)O)is conducted in the presence of Lorentz forces.The flow configuration is modeled between the parallel rotating plates in which the lower plate is permeable.The models which govern the flow in rotating system are solved numerically over the domain of interest and furnished the results for the temperature,entropy generation and thermophysical characteristics of the hybrid as well as conventional nanofluids,respectively.It is examined that the thermal profile intensifies against stronger thermal radiations and magnetic field.The surface of the plate is heated due to the imposed thermal radiations and magnetic field which cause the increment in the temperature.It is also observed that the temperature declines against more rotating plates.Further,the entropy production increases for more dissipative effects and declines against more magnetized fluid.Thermal conductivities of the hybrid nanofluid enhances promptly in comparison with regular liquid therefore,under consideration hybrid nanofluid is reliable for the heat transfer.Moreover,dominating thermal transport is perceived for the hybrid nanofluid which showed that hybrid suspension GO-MoS_(2)/C_(2)H_(6)O_(2)–H_(2)O is better for industrial,engineering and technological uses.

Measurement of Thermophysical Property of Energy Storage System (CaCl₂&#46NH₃System)

In order to measure the thermophysical properties of ammoniated salt (CaCl2.mNH3: m = 4, 8) as an energy storage system utilizing natural resources, the measurement unit was developed, and the thermophysical properties (effective thermal conductivity and thermal diffusivity) of CaCl2.mNH3 and CaCl2.mNH3 with heat transfer media (Ti: titanium) were measured by the any heating method. The effective thermal conductivities of CaCl2.4NH3 + Ti and CaCl2.8NH3 + Ti were 0.14 - 0.17 and 0.18 - 0.20 W/(m.K) in the measuring temperature range of 290 - 350 K, respectively, and these values were approximately 1.5 - 2.2 times larger than those of CaCl2.4NH3 and CaCl2.8NH3. The effective thermal diffusivities were 0.22 - 0.24 × 10-6 and 0.18 - 0.19 × 10-6 m2/sin the measuring temperature range of 290 - 350 K, respectively, and these values were approximately 1.3 - 1.5 times larger than those of CaCl2.4NH3 and CaCl2.8NH3. The obtained results show that the thermophysical properties have a dependence on the bulk densities and specific heats of CaCl2.mNH3 and CaCl2.mNH3 + Ti. It reveals that the thermophysical properties in this measurement would be the valuable design factors to develop energy and H2 storage systems utilizing natural resources such as solar energy.