Influence of Hot Deformation and Subsequent Austempering on the Mechanical Properties of Hot Rolled Multiphase Steel

Influence of hot deformation and subsequent austempering on the mechanical properties of hot rolled multiphase steel was investigated. Thermo-mechanical control processing （TMCP） was conducted by using a laboratory hot rolling mill, where three different kinds of finishing rolling reduction, and austemperings with various isothermal holding duration were applied. The results have shown that a multiphase microstructure consisting of polygonal ferrite, granular bainite and larger amount of stabilized retained austenite can be obtained by controlled rolling processes. Mechanical properties increase with increasing the amount of deformation because of the stabilization of retained austenite. Ultimate tensile strength （σb）, total elongation （σ） and the product of ultimate tensile strength and total elongation （σb-σ） reach the maximum values （791 MPa, 36% and 28476 MPa%, respectively） at optimal processes.

Effects of Austempering after Hot Deformation on the Mechanical Properties of Hot Rolled Si-Mn TRIP Steel Sheets

Excellent mechanical properties are obtained by austempering after hot deformation without subsequent heat treatment in the present Si-Mn TRIP steel sheets. Isothermal holding time after finishing rolling has affected the mechanical properties of this steel. The results show that the sample exhibits a good combination of ultimate tensile strength and total elongation when it is held at the bainite transformation temperature after hot deformation. The stability of retained austenite increases with an increase of isothermal holding time, and a further increase in the holding duration results in a decrease of it. The tensile strength, total elongation and strength ductility reach the maximum values (774MPa, 33% and 25542MPa% respectively) for this sort of hot rolled Si-Mn TRIP steel using the optimal technology.

Stream Surface Strip Element Method and Simulation of Three-Dimensional Deformation of Continuous Hot Rolled Strip

A new method,the stream surface strip element method,for simulating the three-dimensional deformation of plate and strip rolling process was proposed.The rolling deformation zone was divided into a number of stream surface(curved surface)strip elements along metal flow traces,and the stream surface strip elements were mapped into the corresponding plane strip elements for analysis and computation.The longitudinal distributions of the lateral displacement and the altitudinal displacement of metal were respectively constructed to be a quartic curve and a quadratic curve,of which the lateral distributions were expressed as the third-power spline function,and the altitudinal distributions were fitted in the quadratic curve.From the flow theory of plastic mechanics,the mathematical models of the three-dimensional deformations and stresses of the deformation zone were constructed.Compared with the streamline strip element method proposed by the first author of this paper,the stream surface strip element method takes into account the uneven distributions of stresses and deformations along altitudinal direction,and realizes the precise three-dimensional analysis and computation.The simulation example of continuous hot rolled strip indicates that the method and the model accord with facts and provide a new reliable engineering-computation method for the three-dimensional mechanics simulation of plate and strip rolling process.

Model Building of Backup Roller Diameter Effect Rate in 4-High Mill

Software for calculating the strip profile in 4-high hot rolling mill was developed using influence coefficient method. Regularity of backup roller diameter effect rate was studied systematically using the software. The results show that backup roller diameter effect rates decrease versus the increase of strip width, increase significantly versus the increase of backup roller diameter and obscurely increase versus the increase of reduction. The difference between backup roller diameter effect rate and it is reference value increases versus strip width increasing. When backup rollers diameter is set to be 1.64 m and strip width is 1.85 m, the error of strip profile calculated using the model of backup roller diameter effect rate reference value will be 3.55μm. Based on the results, reference values of roller diameter effect rate and six power polynomial fitting coefficients of modification coefficients were determined considering coherent parameters. The high precision model of backup roller diameter effect rate was established. When the model is used to predict strip profile, the accuracy is less than 5.0 μm.

Effect of Deformation between Stands on the Strip Shape in Hot Rolling

A theoretical model about the secondary deformation is developed by the combination of analytical and experimental approaches. A system simulation based on the model is completed to predict the strip profile after the interstand deformation. On the other hand, comprehensive experiments and quantitative comparisons are made to calibrate the model for a wide variety of products. As a result, the correction of the model has been verified by the actual rolling data from production mill and it is helpful to improve the strip shape control.

Research on Single-Side Long Edge of Hot Rolled Strip Caused by Asymmetrical Stiffness of Mill Stand

To analyze and solve the problem of single-side long edge of hot rolled strip in certain domestic factory, the asymmetrical deformation of rolls and strip in asymmetrical stiffness mill stand based on slit beam model, the strip profile and rolling force distribution at the exit of asymmetric stiffness stand mill were calculated using influence function method. Considering the character of in-site equipment and technology, a scheme of adjusting load distribution in finishing mill was made and the experiment was applied. Comparison of strip profile between new load distribution and the old one shows that the method can solve single-side long edge problem well.

Deformation Stability of GH4033 Superalloy in the Hot Continuous Rolling Process Based on Dynamic Material Model and Finite Element Model

The flow stress behavior of GH4033 superalloy was determined by the hot compression tests at the temperatures of 1223-1473 K and the total strains of 0.6 with the strain rates of 0.001-30.0 s^(-1) by using cylindrical samples.The processing maps based on the dynamic material model(DMM)combined with the corresponding microstructure observations indicate the reasonable processing domain locating at the strain rates of 0.1-1.0 s^(-1) and the deformation temperature of 1273-1423 K.Meanwhile,the numerical simulation based on finite element model(FEM)described the variation of the effective strain,effective strain rate and the temperature for the core node,and unveiled the influence of the hot rolling parameters considering the initial temperature(T_(0))range of 1223-1473 K and the first-stand biting velocity(v_(0))range of 0.15-0.35 m·s^(-1).Furthermore,the deformation stability of GH4033 superalloy in the round rod hot continuous rolling(HCR)process is described and analyzed by coupling the three-dimensional(3-D)processing map,and the spatial trajectory lines were determined by the numerically simulated temperatures,the strains and the strain rates.Finally,the results show that the hot deformation stability of GH4033 can be achieved by the rolling process parameters located at T_(0)=1423 K and v_(0)=0.25 m·s^(-1).Additionally,the practical HCR processes as T_(0)=1423 K and v_(0)=0.15,0.25,0.35 m·s^(-1) were operated to verify the influence of the hot rolling parameters on the hot deformation stability by the microstructure observation of the final products.

Effect of hot rolling on microstructure and properties of the ZEK100 alloy

Attempts to expand manufacturing capabilities of magnesium-based sheet materials are described.The as-cast ZEK100(Mg-1.2Zn-0.35Zr-0.17Nd,in wt%)magnesium alloy was subjected to hot rolling at temperatures from 350℃to 450℃using the laboratory 50 ton reversible mill with preheated rolls to manufacture the 1.5-1.7 mm thick sheet.The rolling temperature affected the sheet properties and an increase in the rolling temperature from 250 to 450℃caused reduction of tensile strength from 257 to 228 MPa ac-companied by a reduction in tensile yield stress from 237 to 185 MPa.At the same time,the alloy elongation increased from 17 to 21%.For the same rolling temperature range,the compressive strength reduced from 418 to 351 MPa.The post-rolling annealing at 450℃led to reduction of both tensile and compressive properties with the largest changes corresponding to the rolling temperature of 350°C.The correlation between the alloy grain size after rolling and the sheet properties was established where a reduction in grain size was accompanied by an increase of both the tensile/compressive strength and yield stress.Based on Hall-Petch relationship and an average grain size the correlation developed in this study may be used as the prediction model for properties of the hot rolled magnesium sheet.The results are discussed in terms of recent developments in magnesium sheet alloys and the vital role played in this process by rare earth elements.

3D FE Analysis of Thermal Behavior of Billet in Rod and Wire Hot Continuous Rolling Process

An FE model was developed to study thermal behavior during the rod and wire hot continuous rolling process. The FE code MSC. Marc was used in the simulation using implicit static arithmetic. The whole rolling process of 30 passes was separated and simulated with several continuous 3D elastic-plastic FE models. A rigid pushing body and a data transfer technique were introduced into this model. The on-line experiments were conducted on 304 stainless steel and GCr15 steel hot continuous rolling process to prove the results of simulation by implicit static FEM. The results show that the temperature results of finite element simulations are in good agreement with experiments, which indicate that the FE model developed in this study is effective and efficient.

Hot deformation behavior of a Cr-containing low carbon steel in the ferrite range

A low carbon steel with Cr addition of 0.46wt% combined with trace elements of Mn and Ti was studied. The apparent activation energy of deformation and the hot deformation equation of the steel in the ferritic range were determined by means of single hot compression tests. The hot-rolled strip of 3 mm in thickness rolled in the ferritic range was obtained using a laboratory hot rolling mill. The mechanical properties show that the values of yield strength and ultimate tensile strength are 230 and 330 MPa, respectively, and the elongation is 33%. The average r-value is 1.1. Large polygonal ferrite recrystallization grains with about 40 grn in size and the strong { 111 } recrystallization texture can be obtained in the hot-rolled strip.

Thermo-mechanical coupled analysis of hot ring rolling process

A 3D rigid-plastic and coupled thermo-mechanical FE model for hot ring rolling(HRR) was developed based on DEFORM 3D software,then coupled heat transferring,material flow and temperature distribution of the ring in HRR were simulated and the effects of process parameters on them were analyzed.The results show that the deformation nonuniformity of ring blank increases with the increase of the rotational speed of driver roll and friction factor or the decrease of the feed rate of idle roll and initial temperature of ring blank.The temperature nonuniformity of ring blank decreases with the increase of the feed rate of idle roll or the decrease of initial temperature of ring blank and friction factor.There is an optimum rotational speed of driver roll under which the temperature distribution of ring blank is the most uniform.The results obtained can provide a guide for forming parameters optimization and quality control.

Microstructure and hot compression behavior of twin-roll-casting AZ41M magnesium alloy

The relationship of true stress and true strain of AZ41M magnesium alloy under twin-roll-cast （TRC） and hot compression was analyzed us- ing a Gleeble 1500 machine. Microstructural evolutions of the TRC magnesium alloy under different deformation conditions （strain, sWain rate and deformation temperature） were examined using optical microscopy and discussed. The relationship of true stress and true sWain pre- dicted that lower deformation temperature and higher sWain rate caused sharp strain hardening. Meanwhile, the flow stress curve turned into a steady state at high temperature and lower strain rate. The intermediate temperature and strain rate （623 K and 0.01 s^-1） is appropriate.

Transformation of low carbon steel during deformation at γ/α temperature based on online rolling data

Alloying elements, such as silicon and manganese, have a major impact on the phase transformation point of steel. Specifically, manganese is an element for the expansion and stability of the austenite region, while silicon can expand and stabilize the ferrite region. Phase transformation occurs during the hot rolling process for the steel with certain silicon content, which leads to great changes of the deformation resistance, thereby affecting the rolling stability. Consequently, a better understanding of phase transformation in the rolling process will contribute to the enhancement of product quality. In this paper ,the on-line rolling data were processed by means of the inverse calculation method. In this method, the steel deformation resistance with various silicon and manganese contents was obtained and analyzed to determine the deformation behavior of the steel, which can help improve the on-line control model and enhance the steel quality.

Strip shape control capability of hot wide strip rolling mills

The elasticity deformation of rolls was analyzed by means of two-dimensional finite element method （FEM） with variable thickness. Three typical mills were used as objects for analysis. A thorough study was done on the control capabilities of these mills on the strip shape. Then the strip shape control capabilities of the three mills was compared synthetically. 2008 University of Science and Technology Beijing. All rights reserved.

基于DEFORM的棒材热轧过程的数值模拟及缺陷分析

利用有限元软件DEFORM3D对某厂棒材热连轧过程中的第1道次进行了数值模拟,通过后处理数据的分析,模拟缺陷位置与实际缺陷位置较吻合;同时探讨了缺陷产生的原因,为工艺优化提供了依据。

基于DEFORM的钨板热轧的研究

钨板的热轧工艺是钨板制造过程中的首道工序,与钨板的加工质量直接相关。本文利用DEFORM软件,结合实际生产,提出三种工艺方案,并从应力应变、破坏情况等方面进行比较。结果表明:在1000℃-1500℃温度范围内,钨板热处理温度1250℃、变形率30%情况下,钨板轧制的综合条件较优。

基于Deform的热轧3003铝板带温度场的三维有限元模拟

采用三维有限元模拟方法研究了轧制速度、轧制界面热交换系数、轧件初始温度和压下率对热轧3003铝合金板带温度场的影响。结果表明:随着轧制速度增加,轧件温度升高,轧件的表面温差加大。因此,增加轧制速度需要加大乳化液喷射量。随着界面换热系数的变大,轧件的温度逐渐降低,轧件的表面温差减小。同时,大的界面换热系数可以减小乳化液喷射量。随着轧件初始温度的增加,轧件的表面温差减小。为了使得轧件温度分布更均匀,如果条件允许,可适度提高轧件的初始温度。随着压下率的增加,轧件在轧制区的平均温度随之升高,轧件的表面温度变化幅度加剧。因此,随着压下率的加大,需要增加乳化液的喷射量。

Deformation Behavior and Microstructure Evolution of Wrought Magnesium Alloys

There are many researches on the deformation behavior of wrought magnesium alloys, such as AZ31, AZ80, AZ91, and ZK60 magnesium alloys at different temperatures and strain rates, but few of them focuses on the deformation behavior of AZ41M and ZK60M alloys, especially under the twin-roll casting (TRC) state. Meanwhile, the existing researches only focus on the grain refinement law of the magnesium alloys under deformation conditions, the deformation mechanism has not been revealed yet. The hot compression behavior of AZ41M and ZK60M magnesium alloys under the temperature and strain rate ranges of 250-400 ℃ and 0.001-1 s-1 are studied by thermal simulation methods using Gleeble 1500 machine and virtual simulation using finite element analysis software. Simulation results show that sine hyperbolic law is the most suitable flow stress model for wider deformation conditions. The most reasonable selected deformation conditions of ZK60M alloy is 350 oC/0.1 s-1 for TRC and 350 oC/1 s-1 for conventional casting (CC), while AZ41M alloy is 300 oC/0.01 s-1 for TRC and 350 oC/0.1 s-1 for CC. Deformation behavior and dynamic recrystallization (DRX) mechanism of them are analyzed at the same deformation conditions. The microstructures of AZ41M and ZK60M alloys are observed at different deformed conditions by optical microscopy (OM) and electron back scatter diffraction (EBSD) and it reveals the flow behavior and deformation mechanism of them. Working harden and work soften contribute to the activation of basal, non-basal slip systems which promote DRX. The proposed research reveals the deformation behavior and mechanism of the AZ41M and ZK 60M magnesium alloys and concludes their optimized deformation parameters and processes and provides a theory basis for their manufacturing and application.

基于deform-3D的钼窄带轧制模拟研究

本文采用deform-3D软件,通过有限元分析方法分析了钼带轧制过程中轧制辊型变化和钼丝直径变化对产品的影响,研究了采用有限元方法分析钼带轧制过程的可行性。结果表明:采用钼的一般特性数据和经验数据通过有限元模拟计算可有效模拟钼带轧制过程,帮助正确选择轧制辊型和丝径等参数,精确度高、节省时间、降低试验成本。

基于DEFORM-3D的钢球热压成形工艺优化

基于钢球的三维模型,利用DEFORM-3D软件对钢球无环带热压过程进行仿真分析,实现在加工前对热压后钢球内部金属流线及应力分布、内部缺陷及环带尺寸情况的预测,通过正交试验研究热压钢球球坯垂直赤道截面的纤维组织流线特征,根据仿真分析设计无环带钢球模具尺寸,并对加工工艺参数进行优化。结果证明:该研究实现了对钢球环带尺寸的控制及内部金属流线的优化,避免了钢球高速运行状态下在金属流线断裂处形成表面裂纹,提高了钢球加工质量。