Inner damage identification and residual strength assessment of a 3D printed tunnel with marble-like cementitious materials using piezoelectric transducers

Quantitative damage identification of surrounding rock is important to assess the current condition and residual strength of underground tunnels.In this work,an underground tunnel model with marble-like cementitious materials was first fabricated using the three-dimensional(3D)printing technique and then loaded to simulate its failure mode in the laboratory.Lead zirconate titanate piezoelectric(PZT)transducers were embedded in the surrounding rock around the tunnel in the process of 3D printing.A 3D monitoring network was formed to locate damage areas and evaluate damage extent during loading.Results show that as the load increased,main cracks firstly appeared above the tunnel roof and below the floor,and then they coalesced into the tunnel boundary.Finally,the tunnel model was broken into several parts.The resonant frequency and the peak of the conductance signature firstly shifted rightwards with loading due to the sealing of microcracks,and then shifted backwards after new cracks appeared.An overall increase in the root-mean-square deviation(RMSD)calculated from conductance signatures of all the PZT transducers was observed as the load(damage)increased.Damage-dependent equivalent stiffness parameters(ESPs)were calculated from the real and imaginary signatures of each PZT at different damage states.Satisfactory agreement between equivalent and experimental ESP values was achieved.Also,the relationship between the change of the ESP and the residual strength was obtained.The method paves the way for damage identification and residual strength estimation of other 3D printed structures in civil engineering.

Novel Traveling Wave Sandwich Piezoelectric Transducer with Single Phase Drive:Theoretical Modeling,Experimental Validation,and Application Investigation

Most of traditional traveling wave piezoelectric transducers are driven by two phase different excitation signals,leading to a complex control system and seriously limiting their applications in industry.To overcome these issues,a novel traveling wave sandwich piezoelectric transducer with a single-phase drive is proposed in this study.Traveling waves are produced in two driving rings of the transducer while the longitudinal vibration is excited in its sandwich composite beam,due to the coupling property of the combined structure.This results in the production of elliptical motions in the two driving rings to achieve the drive function.An analytical model is firstly developed using the transfer matrix method to analyze the dynamic behavior of the proposed transducer.Its vibration characteristics are measured and compared with computational results to validate the effectiveness of the proposed analytical model.Besides,the driving concept of the transducer is investigated by computing the motion trajectory of surface points of the driving ring and the quality of traveling wave of the driving ring.Additionally,application example investigations on the driving effect of the proposed transducer are carried out by constructing and assembling a tracked mobile system.Experimental results indicated that 1)the assembled tracked mobile system moved in the driving frequency of 19410 Hz corresponding to its maximum mean velocity through frequency sensitivity experiments;2)motion characteristic and traction performance measurements of the system prototype presented its maximum mean velocity with 59 mm/s and its maximum stalling traction force with 1.65 N,at the excitation voltage of 500 V_(RMS).These experimental results demonstrate the feasibility of the proposed traveling wave sandwich piezoelectric transducer.

Fluid Pump Using a Bar-shaped Piezoelectric Transducer

There are two kinds of piezoelectric pumps:check valve pumps and valve-less pumps.Whether to use a check valve or not depends upon the application occasion.To achieve large backpressure for higher flow rates,the pump with check valve is desirable.However,adding check valves implies more complex structure and higher probability of valve blocking,etc.In order to solve the problem,effective driving and transport mechanics with compact construction and reliable service are being sought.In this paper,using the second-order longitudinal vibration mode of a bar-shaped piezoelectric vibrator for driving fluid,a piezoelectric pump is successfully made.The proposed piezoelectric pump consists of coaxial cylindrical shells and a bar-shaped piezoelectric vibrator,which has a disk part and a cone part.The lead zirconium titanate ceramic rings fixed in the vibrator are polarized along the thickness direction.When the second-order longitudinal vibration of the vibrator along its axis is excited,the disk part of the vibrator changes periodically the volume of the chamber and the cone part acts as a pin valve,driving the fluid from the inlet port to the outlet port.Finite elements analysis on the proposed pump model is carried out to verify its operation principle and design by the commercial FEM software ANSYS.Components of the piezoelectric pump were manufactured,assembled,and tested for flow rate and backpressure to validate the concepts of the proposed pump and confirm the simulation results of modal and harmonic analyses.The test results show that the performance of the proposed piezoelectric pump is about 910 mL/min in flow rate with a highest pressure level of 1.5 kPa under 400 V peak-to-peak voltage and 51.7 kHz operating frequency.It is confirmed that this bar-shaped piezoelectric transducer can be effectively applied in fluid transferring mechanism of pump through this research.

Study on Enhancement Effect of Cavitation Caused by HIFU Piezoelectricity Transducer

An orthogonal ultrasonic irradiation system consisting of HIFU with frequency at 1.05 MHz combined with ultrasound with frequency at 28 kHz was applied in this paper.Effect of cavitation was detected by pH-value measurement and conductance measurement.The result shows that the effect of cavitation caused by ultrasound with frequency at 28 kHz is greatly enhanced by HIFU piezoelectricity transducer with frequency at 1.05 MHz.

DYNAMIC CHARACTERISTICS OF AXIALLY-SYMMETRICAL ANNULAR CORRUGATED SHELL PIEZOELECTRIC TRANSDUCERS

The coupled extensional and flexural vibrations of an annular corrugated shell piezoelectric transducer consisting of multiple circularly-annular surfaces smoothly connected along the interfaces were investigated in the paper. Only a time-harmonic voltage is applied across two electrodes of the piezoelectric shell as the external loading. A theoretical solution was obtained using the classical shell theory. Based on the solution, basic vibration characteristics of resonant frequencies, mode shapes were calculated and examined.

A unidirectional SH wave transducer based on phase-controlled antiparallel thickness-shear(d15)piezoelectric strips

In recent years,shear horizontal(SH)waves are being paid more and more attention to in structural health monitoring as it has only one displacement component.In this paper,a unidirectional SH wave transducer based on phase-controlled antiparallel thickness-shear(d15)piezoelectric strips(APS)is proposed.Here two pairs of identical APS were used each of which is a bidirectional SH wave transducer.By setting the interval between the two pairs of APS as 1/4 wavelength and the excitation delay between them as 1/4 period of the central operating frequency,unidirectional SH waves can be excited.Both finite element simulations and experiments were performed to validate the proposed design.Results show that SH0 waves were successfully excited only along one direction and those along the unwanted directions were suppressed very well.The proposed unidirectional SH wave transducer is very helpful to study the fundamentals and applications of SH waves.

Voltage Generated Characteristics of Piezoelectric Ceramics Cymbal Transducer

In this study the relation between the generated open circuit output voltages of the piezoelectric ceramics Cymbal transducers with applied impact mechanical energy is studied. The output voltages of piezoelectric ceramics Cymbal transducers are increased with the increasing of the applied mechanical energy. Under the same impact mechanical energy, the generated open circuit output voltages of the piezoelectric ceramics Cymbal transducer is much higher than that of uncapped piezoelectric ceramics disk alone. The generated open circuit output voltages of the piezoelectric ceramics Cymbal transducer depend on the geometry parameters and the metal thickness of end-cap. The generated open circuit voltage of piezoelectric ceramics Cymbal transducer with thick metal thickness is small than that with thin metal thickness.

Analysis of Vibration Frequencies of Piezoelectric Ceramic Rings as Ultrasonic Transducers in Welding of Facial Mask Production

The explosive demands for facial masks as vital personal protection equipment(PPE)in the wake of Covid-19 have challenged many industries and enterprises in technology and capacity,and the piezoelectric ceramic(PZT)transducers for the production of facial masks in the welding process are in heavy demand.In the earlier days of the epidemic,the supply of ceramic transducers cannot meet its increasing demands,and efforts in materials,development,and production are mobilized to provide the transducers to mask producers for quick production.The simplest solution is presented with the employment of Rayleigh-Ritz method for the vibration analysis,then different materials can be selected to achieve the required frequency and energy standards.The fully tailored method and results can be utilized by the engineers for quick development of the PZT transducers to perform precise function in welding.

New Three Dimension Piezoelectric Transducer

Abstract: A new type of piezoelectric transducer with compression/shear sense is developed and was successfully tested for measuring three dimension accelerations in shock and vibration experiment.

Design and analysis of longitudinal–flexural hybrid transducer for ultrasonic peen forming

Ultrasonic peen forming(UPF)is an emerging technology that exhibits great superiority in both its flexible operating modes and the deep residual stress that it produces compared with conventional plastic forming methods.Although ultrasonic transducers with longitudinal vibration have been widely studied,they have seldom been incorporated into UPF devices for machining in confined spaces.To meet the requirements of this type of machining,a sandwich-type piezoelectric transducer with coupled longitudinal-flexural vibrational modes is proposed.The basic structure of the transducer is designed to obtain large vibrational amplitudes in both modes.Experimental results obtained with a prototype device demonstrate the feasibility of the proposed transducer.The measured vibrational amplitude for the working face in the longitudinal vibrational mode is 1.0μm,and electrical matching increases this amplitude by 40%.The flexural vibration characteristics of the same prototype transducer are also tested and are found to be slightly smaller than those of longitudinal mode.The resultant working strokes of the UPF impact pins reach 1.7 mm and 1.2 mm in the longitudinal and flexural modes,respectively.The forming capability of the prototype has been evaluated via 15-min machining on standard 2024-T351 aluminum plates.After UPF,an improved surface morphology with lower surface roughness is obtained.The aluminum plate test piece has an apparent upper deformation with an arc height of 0.64 mm.The measured peak value of the compressive residual stress is around 250 MPa,appearing at a depth of 100μm.The proposed longitudinal-flexural hybrid transducer thus provides a high-performance tool for plate peen forming in confined spaces.

Analysis on Output Power for Multi-direction Piezoelectric Vibration Energy Harvester

To predict the performance of multi-direction piezoelectric vibration energy harvester,an equation for calculating its output power is obtained based on elastic mechanics theory and piezoelectricity theory.Experiments are performed to verify theoretical analysis.When the excitation direction is along Y direction,a maximal output power about 0.139 mW can be harvested at a resistive load of 65kΩ and an excitation frequency of 136 Hz.Theoretical analysis agrees well with experimental results.Furthermore,the performance of multi-direction vibration energy harvester is experimentally tested.The results show that the multi-direction vibration energy harvester can harvest perfect energy as the excitation direction changes in XY plane,YZ plane,XZ plane and body diagonal plane of the harvester.

Structure of Pb(Zr,Ti)O3(PZT)for Power Ultrasonic Transducer

To improve the performance of ultrasonic transducer, the samples of PZT were improved by doping. The doped PZT was observed and analyzed from the following aspects： the crystal phase structures, the surface morphologies and the dielectric constant. According to the transducer parameter requirements for ultrasonic machining, there are also requirements for the parameters of piezoelectric ceramics. The high performance PZT was prepared by doping the elements of Ga, Ba, Nb, Sn, and Sr in PZT. The doped PZT is suitable for power ultrasonic machining at 20 kHz through analysis using X-ray diffraction（XPD）, a scanning electron microscope（SEM） and LCR meter. Therefore, the excellent performance of transducer for power ultrasonic machining is guaranteed.

HIGH-FREQUENCY VIBRATIONS OF CORRUGATED CYLINDRICAL PIEZOELECTRIC SHELLS

Coupled extensional and flexural cylindrical vibrations of a corrugated cylindrical piezoelectric shell consisting of multiple pieces of circular cylindrical surfaces smoothly connected along their generatrix are studied. To validate the results for the case of relatively thick shells or equivalently high-frequency modes with short wavelengths, existing analysis is extended by considering shear deformation and rotatory inertia. An analytical solution is obtained. Based on the solution, resonant frequencies and mode shapes are calculated.

Recent Advancements in Ultrasound Transducer:From Material Strategies to Biomedical Applications

Ultrasound is extensively studied for biomedical engineering applications.As the core part of the ultrasonic system,the ultrasound transducer plays a significant role.For the purpose of meeting the requirement of precision medicine,the main challenge for the development of ultrasound transducer is to further enhance its performance.In this article,an overview of recent developments in ultrasound transducer technologies that use a variety of material strategies and device designs based on both the piezoelectric and photoacoustic mechanisms is provided.Practical applications are also presented,including ultrasound imaging,ultrasound therapy,particle/cell manipulation,drug delivery,and nerve stimulation.Finally,perspectives and opportunities are also highlighted.

Design of Sandwich Transducer Based on the Equivalent Length Algorithm

The sandwich transducer structure is comprised of threecomponents along its main axis: the back metal cap, piezoelectricceramic stack and the horn. The purpose of this work is topresent a simplified method, referred as the equivalent lengthalgorithm, to design the actuator parameters including eachsegment length and the resonance frequency fs. The actuatorlength L and the propagation wavelength λ along its main axissatisfy the standing wave theory. So, define an equivalent lengthcoefficient for each part of the actuator, and then the sandwichstructure is regarded as a single material cylindrical rod withequivalent length L′. According to the standing wave theory, theequivalent length L′ of the actuator can be determined with thegiven resonance frequency fs, or vice versa. The phase length ofeach part of the actuator in the standing wave is optimized freelyin the design procedure. The actual length of each part of theactuator is determined by the equivalent length coefficient.Finally, the resonance frequencies of three given actuators arecalculated with this method. They are compared with thoseobtained through Ansys simulation and those measured by animpedance analyzer. The results show agreement.

Analysis of Vibrational Performance of A Piezoelectric Micropump with Diffuse/Nozzle Microchannel

Piezoelectric transducers of different external diameters are designed and fabricated and incorporated into micropumps. Through finite element analysis, it is shown that the volume efficiency of the micropump reaches its maximum value for the first mode of vibration. The variation of maximum displacement with frequency is determined under free and forced vibration. Results demonstrate that this variation shows the same trend for different driving waves at the same driving voltage. The maximum displacement under forced vibration is less than that under free vibration. The displacement increases with decreasing distance from the center of the transducer. The maximum displacement is inversely proportional to the diameter of the transducer and proportional to the driving voltage under both free and forced vibrations. Finally, the micropump flow rate and pressure are measured and are found to manifest the same trend as the maximum displacement under the same driving conditions. For a piezoelectric transducer of 12 mm external diameter, the maximum flow rate and pressure value are 150 μL/min and 346 Pa, respectively, under sine-wave driving at 100 Vpp driving voltage.

ELECTRIC FIELD MICROSENSOR BASED ON THE STRUCTURE OF PIEZOELECTRIC INTERDIGITATED CANTILEVER BEAMS

This paper presents the design, fabrication, and preliminary experimental result of an electric field microsensor based on the structure of piezoelectric interdigitated cantilevers with staggered vertical vibration mode. The working principle of this electric field microsensor is demonstrated, and the induced charges and structural parameters of this microsensor are simulated by the finite element method. The electric field microsensor was fabricated by Micro-Electro Mechanical Systems(MEMS) technique. Each cantilever is a multilayer compound structure(Al/Si3N4/ Pt/PZT/Pt/ Ti/SiO 2/Si), and Piezoelectric, PieZ oelectric ceramic Transducer(PZT)(PbZ rxTi(1–x)O3) layer, prepared by sol-gel method, is used as the piezoelectric material to drive the cantilevers vibrating. This electric field microsensor was tested under the DC electric field with the field intensity from 0 to 5×104 V/m. The output voltage signal of the electric field microsensor has a good linear relationship to the intensity of applied electric field. The performance could be improved with the optimized design of structure, and reformative fabrication processes of PZT material.

Modification of Pb(Zr,Ti)O3 by Doping Mo based on High Power Ultrasonic Transducer

In view of the special requirements of transducers for power ultrasonic processing,the piezoelectric ceramic material Pb(Zr,Ti)O3 was modified by adding other effective elements.The piezoelectric ceramic piece has a good crystal phase structure,a stable piezoelectric constant,a higher dielectric constant,and a lower dielectric loss by adding a small amount of Sr^2+,Ba^2+,Ga^2+,Sn^4+,Nb^5+,etc.These properties are well suited to requirements of power ultrasonic transducer more than 1 000 W.The crystal phase structure and surface morphology of the modified piezoelectric ceramic chips were analyzed by X-ray and scanning electron microscopy (SEM) to prove that the piezoelectric ceramic chips have good crystal structure and density.The dielectric constant of the polarized piezoelectric ceramic chips was measured using an LCR meter.Finally,the piezoelectric ceramic chips were used to design the ultrasonic transducer,and the transducer was analyzed and measured by the impedance analyzer.The measurement results show that the performance of the piezoelectric ceramic chips is reasonable and feasible.

Development of Optical Voltage Transducer Based on Dual-Mode Highly Elliptical-Core Polarization Maintenance Fiber

This paper describes an optical voltage transducer （OVT） for the 35 kV electric power system based on modular interference in dual-mode highly elliptical-core polarization maintenance fiber （E-Core PMF）. The temperature and environmental perturb- bation can be compensated automatically. In the scheme, a quartz crystal cylinder wrapped with highly elliptical-core fiber plays the role of voltage sensor head. The two interference output lobes＇ intensity from the E-core PMF is modulated with the converse piezoelectric effect of quartz crystal. A PZT wrapped with E-core PMF at ground potential serves as the static modular phase difference control and temperature compensation unit. The experiment results indicate that the OVT designed in this paper has satisfying performance and could successfully rejects the temperature perturbation.