Die Casting Mold Design of the Thin-walled Aluminum Case by Computational Solidification Simulation

Recently, demand for the lightweight alloy in electric/electronic housings has been greatly increased. However, among the lightweight alloys, aluminum alloy thin-walled die casting is problematic because it is quite difficult to achieve sufficient fluidity and feedability to fill the thin cavity as the wall thickness becomes less than 1mm. Therefore, in this study, thin-walled die casting of aluminum （Al-Si-Cu alloy： ALDC 12） in size of notebook computer housing and thickness of 0.8 mm was investigated by solidification simulation （MAGMA soft） and actual casting experiment （Buhler Evolution B 53D）. Three different types of gating design, finger, tangential and split type with 6 vertical runners, were simulated and the results showed that sound thin-walled die casting was possible with tangential and split type gating design because those gates allowed aluminum melt to flow into the thin cavity uniformly and split type gating system was preferable gating design comparing to tangential type gating system at the point of view of soundness of casting and distortion generated after solidification. Also, the solidification simulation agreed well with the actual die-casting and the casting showed no casting defects and distortion.

Thin-Wall Aluminum Die-Casting Technology for Development of Notebook Computer Housing

Silicon-based aluminum casting alloys are known to be one of the most widely used alloy systems mainly due to their superior casting characteristics and unique combination of mechanical and physical properties. However,manufacturing of thin-walled aluminum die-casting components,less than 1.0 mm in thickness,is generally known to be very difficult task to achieve aluminum casting alloys with high fluidity.Therefore,in this study,the optimal die-casting conditions for producing 297 mm×210 mm×0.7 mm thin-walled aluminum component was examined experimentally by using 2 different gating systems,tangential and split type,and vent design.Furthermore,computational solidification simulation was also conducted.The results showed that split type gating system was preferable gating design than tangential type gating system at the point of view of soundness of casting and distortion generated after solidification.It was also found that proper vent design was one of the most important factors for producing thin-wall casting components because it was important for the fulfillment of the thin-wall cavity and the minimization of the casting distortion.

Feasibility of semi-solid die casting of ADC12 aluminum alloy

The feasibility of semi-solid die casting of ADC12 aluminum alloy was studied. The effects of plunger speed, gate thickness, and solid fraction of the slurry on the defects were determined. The defects investigated are gas and shrinkage porosity. In the experiments, semi-solid slurry was prepared by the gas-induced semi-solid （GISS） technique. Then, the slurry was transferred to the shot sleeve and injected into the die. The die and shot sleeve temperatures were kept at 180 ℃ and 250 ℃, respectively. The results show that the samples produced by the GISS die casting give little porosity, no blister and uniform microstructure. From all the results, it can be concluded that the GISS process is feasible to apply in the ADC12 aluminum die casting process. In addition, the GISS process can give improved properties such as decreased porosity and increased microstructure uniformity.

Characterization of A390 aluminum alloy produced at different slow shot speeds using vacuum assisted high pressure die casting

The effects of vacuum assistance on the microstructure and mechanical properties of high pressure die cast A390alloy at different slow shot speeds were evaluated.Plate-shaped specimens of hypereutectic A390aluminum alloy were produced on a TOYO BD?350V5cold chamber die casting machine incorporated with a self-improved TOYO vacuum system.According to the results,the vacuum pressure inside the die cavity increased linearly with the increasing slow shot speed at the beginning of mold filling.Meanwhile,tensile properties of vacuum die castings were deteriorated by the porosity content.In addition,the average primary silicon size decreased from23to14μm when the slow shot speed increased from0.05to0.2m/s,which has a binary functional relationship with the slow shot speed.After heat treatment,microstructural morphologies revealed that needle-shaped and thin-flaked eutectic silicon particles became rounded while Al2Cu dissolved intoα(Al)matrix.Furthermore,the fractography revealed that the fracture mechanism has evolved from brittle transgranular fracture to a fracture mode with many dimples after heat treatment.

Mechanism of die soldering during aluminum die casting

Soldering is a unique casting defect associated with die casting or metal mold casting of aluminum al oys. It occurs when molten aluminum sticks or solders the surface of the die steel and remains there after the ejection of the casting, causing a surface defect and dimensional inaccuracy of the castings and increased machine downtime. Soldering occurs easily when a bare die steel mold is used for die casting of aluminum al oys. When molten aluminum comes in contact with the die steel at a temperature higher than a critical temperature, the iron and aluminum atoms diffuse into each other, forming a series of intermetallic phases and a liquid aluminum-rich fcc phase. This liquid phase exists between intermetal ic phases. On cooling, the liquid fcc phase solidiifes on the intermetal ic phases and grows into the casting, resulting in soldering. The critical temperature is the eutectic temperature near the aluminum corner of the phase diagram. If the die is protected using a nonreactive ceramic coating, soldering starts at locations where local coating failure occurs. Molten aluminum comes into contact with die steel through the coating failure locations and eats into the steel matrix, forming smal pits. As these smal pits grow, the coating is gradual y removed and soldering becomes more severe. Details of die soldering step on a bare steel die and on a coated die material are discussed.

Strengthening technology and mechanism for semi-solid die casting of aluminum alloy

Combined with theoretical evaluation, an optimized strengthening process for the semi-solid die castings of A356 aluminum alloy was obtained by studying the mechanical properties of castings solution treated and aged under different conditions in detail, then, the semi-solid die castings and liquid die castings were heat treated with the optimized process. The results show that the mechanical properties of semi-solid die castings of aluminum alloy are superior to those of the liquid die castings, especially the strengthening degree of heat treated semi-solid die castings is much greater than that of liquid die castings with the tensile strength more than 330 MPa and the elongation more than 10%, and this is mainly contributed to the non-dendritic and more compact microstructure of semi-solid die castings. The strengthening mechanism of heat treatment for the semi-solid die castings of A356 aluminum alloy is due to the dispersive precipitation of the second phase（Mg2Si） and formation of GP Zone.

Mould filling ability and microstructure of aluminum alloy under electromagnetic die casting

In order to solve the mould filling problem of large thin walled aluminum alloy castings effectively, a new casting technology called electromagnetic die casting has been developed. Emphasis has laid on studying the mould filling ability and microstructure under the mentioned method. The results show that the mould filling ability of A357 is increasing continually with the increasing of the input voltage, that is, the magnetic induction intensity. The pressure head of the molten metal increases from the lowest one at the input of the mould to the highest one at the end of the mould while in a conventional mould the pressure head depends invariably on the sprue height. Under electromagnetic die casting, the grains of A357 alloy are refined, and the pattern of eutectic silicon of alloy changes from rough plate to smooth strip.

Extrusion force analysis of aluminum pipe fabricated by CASTEX using expansion combination die

To determine the extrusion force of pipe fabricated by continuous casting and extrusion (CASTEX) using an expansion combination die, the metallic expansion combination die was divided into diversion zone, expansion zone, flow dividing zone, welding chamber, and sizing zone, and the corresponding stress formulae in various zones were established using the slab method. The deformation zones of CASTEX groove were divided into liquid and semisolid zone, solid primary gripping zone, and solid gripping zone, and the formulae of pipe extrusion forces were established. Experiments were carried out on the self-designed CASTEX machine to obtain the aluminum pipe and measure its extrusion force using the expansion combination die. The experimental results of radial extrusion force for aluminum pipe are in good agreement with the calculated ones.

Finite element analysis for die casting parameters in high-pressure die casting process

The gating system and the overflow system were designed according to the casting structure during high pressure die casting(HPDC) process. The simulation was carried out by ProCAST software to visualize the injection chamber pre-crystallization and the flow of molten metal. The main work is to research four die casting process parameters, i.e. injection temperature, low-pressure velocity, high-and low-pressure velocity’s switching position, and high-pressure velocity. Experimental results show that the higher injection temperature and lowpressure velocity can mitigate the pre-crystallization of the injection chamber. However, when the low-pressure velocity exceeds 0.2 m·s-1, the air entrapment in the chamber occurs. Besides, when the high-pressure velocity is greater than 2.5 m·s-1, the overflow channel at the final filling position is covered by the liquid metal too early. Finally, the injection temperature of 650 °C, the low-pressure velocity of 0.2 m·s-1, the high-and low-pressure velocity’s switching position of 320 mm and the high-pressure velocity of 2 m·s-1 are obtained as the optimal parameters by the software simulation, which has been verified by actual production.

Semi-solid near-net shape rheocasting of heat treatable wrought aluminum alloys

Flexibility of the CSIR-RCS, induction stirring with simultaneous air cooling process, in combination with high pressure die casting is successfully demonstrated by semi-solid rheocasting of plates performed on commercial 2024, 6082 and 7075 wrought aluminum alloys. Tensile properties were measured for the above mentioned rheocast wrought aluminum alloys in the T6 condition. The results showed that tensile properties were close to or even in some cases exceeded the minimum specifications. The yield strength and elongation of rheocast 2024-T6 exceeded the minimum requirements of the wrought alloy in the T6 condition but the ultimate tensile strength achieved only 90% of the specification because the Mg content of the starting alloy was below the commercial alloy specification. The strengths of rheocast 6082-T6 exceeded all of the wrought alloy T6 strength targets but the elongation only managed 36% of the required minimum due to porosity, caused by incipient melting during solution heat treatment, and the presence of fine intermetallie needles in the eutectic. The yield strength of rheocast 7075 exceeded the required one and the ultimate tensile strength also managed 97% of the specification; while the elongation only reached 46% of the minimum requirement also due to incipient melting porosity caused during the solution heat treatment process.

Influence of samarium content on microstructure and mechanical properties of recycled die-cast YL112 aluminum alloys

The influence of Sm （Samarium） content on microstructure and mechanical properties of recycled die-cast YLl12 aluminum alloys was investigated. The results show that many small Sm-rich particles form in the recycled die-cast YLl12 alloys with Sm addition. At the same time, the secondary dendrite arm spacing in the YLl12 alloys modified with Sm is smaller than that of the unmodified alloy. The eutectic Si of recycled die- cast YL112-xSm alloys transforms from coarse acicular morphology to fine fibres. Mechanical properties of the investigated recycled die-cast YLl12 aluminum alloys are enhanced with Sm addition, and a maximal ultimate tensile strength value （276 MPa） and elongation （3.76%） are achieved at a Sm content of 0.6wt.%. Due to the modification of eutectic Si by Sm, numerous tearing ridges and tiny dimples on the fractures of tensile samples are observed.

Application of Photon-Counting X-ray Computed Tomography to Aluminum-Casting Inspection

One of the issues in the aluminum-alloy die casting industry is the space occurring inside the casting, and the improvement of the verification technology is expected. The purpose of this research is to seal holes inside the aluminum metal by resin and verify them by photon-counting X-ray computed tomography (CT) using an energy-discrimination 64-channel cadmium-telluride (CdTe) line detector. Moreover, it is important to estimate the image of the effective atomic number and the electronic density by the energy mapping of the attenuation coefficient utilizing photon-counting X-ray CTto distinguish both the aluminum metal and the resin filler in the aluminum hole. As a result, the energy discrimination of the resin filler in the space of aluminum casting has been attained. We could observe the atomic number image utilizing dual-energyX-ray CTmethod with the 64-channel CdTe photon-counting detector.

Machining studies of die cast aluminum alloy-silicon carbide composites

Metal matrix composites （MMCs） with high specific stiffness, high strength, improved wear resistance, and thermal properties are being increasingly used in advanced structural, aerospace, automotive, electronics, and wear applications. Aluminum alloy-silicon carbide composites were developed using a new combination of the vortex method and the pressure die-casting technique in the present work. Machining studies were conducted on the aluminum alloy-silicon carbide （SiC） composite work pieces using high speed steel （HSS） end-mill tools in a milling machine at different speeds and feeds. The quantitative studies on the machined work piece show that the surface finish is better for higher speeds and lower feeds. The surface roughness of the plain aluminum alloy is better than that of the aluminum alloy-silicon carbide composites. The studies on tool wear show that flank wear increases with speed and feed. The end-mill tool wear is higher on machining the aluminum alloy-silicon carbide composites than on machining the plain aluminum alloy.

Comparative Analysis of the Effects of Pressure on the Mechanical Properties and Microstructure of Die Cast Aluminum Alloys

A study of the effects of pressure on the microstructure and mechanical properties of two aluminum alloys (A1350 and A380) was carried out and subsequent analysis made. Pressure was regulated at various levels in the die cast machine. Samples of both alloys were cast under varying regulated applied pressure. The mechanical properties of both alloy casts were tested and microstructure analysis done and the results compared for both alloys. The results obtained show that hardness, tensile strength, yield strength and impact strengths for both alloy cast samples followed similar pattern in the casting process. The hardness values increased with applied pressure but not too significantly in both alloy casts as pressure rose in the casting process. The yield strength of both alloy casts also increased with applied pressure. The impact strength and elongations also increased with applied pressure in both alloy casts. Also the microstructure analysis carried out on both alloy casts showed similar pattern of structural changes in the morphologies of both alloy casts as grains became fine as pressure rose from 350 to 1400 kg/cm2. Models were developed for the results and for all the models developed, a close relationship with the experimental results were underlying in view of the small errors generated by them and can be used to predict the experimental values.

Advanced casting technologies for lightweight automotive applications

This paper provides an overview of alloy and process developments in aluminum and magnesium castings for lightweight automotive applications. Wear-resistant aluminum alloys, creep-resistant and high strength/ductility magnesium alloys have been developed for automotive applications. On the process front, vacuumassisted die casting and high vacuum die casting technologies have been developed for high-integrity body and chassis applications. Thin-wall and hollow casting components are being produced by low-pressure die casting processes for structural applications. Overcasting technology is gaining traction and has enabled mixed material designs for automotive sub-systems such as engine cradles and instrument panel beams. Simulation tools developed to predict the interfacial interactions of the dissimilar components and the structural integrity of the overcast systems are being validated in the casting trials.

Cross-sectional distortion behaviors of thin-walled rectangular tube in rotary-draw bending process

The cross-sectional distortion usually appears during rotary-draw bending process of thin-walled rectangular tube with small bending radius.To study the cross-sectional distortion of the tube,a three-dimensional finite-element model of the process was developed based on ABAQUS/Explicit code and its reliability was validated by experiment.Then,the cross-sectional distortion behaviors of the tube were investigated.The results show that a zone of larger circumferential stress appears on the tube when bending angle reaches 30°.And in the larger circumferential stress zone,the sagging phenomenon is produced obviously.The maximum cross-sectional distortion is located in the larger circumferential stress zone and the angle between the plane of maximum cross-sectional distortion and the bending reference plane is about 50°.The position of the maximum cross-sectional distortion keeps almost unchanged with the variation of the clearances between dies and tube.

Effect of depressurizing speed on mold filling behavior and entrainment of oxide film in vacuum suction casting of A356 alloy

The effect of depressurizing speed on mold filling behavior and entrainment of oxide film of A356 alloy was studied. Themold filling behavior and velocity fields were recorded by water simulation with particle image velocimetry. The results show thatthe gate velocity first increased dramatically, then changed with the depressurizing speed: the gate velocity increased slowly atrelatively high depressurizing speed; at reasonable depressurizing speed, the gate velocity kept unchanged; while at lowerdepressurizing speed, the gate velocity decreased firstly and then kept unchanged. High gate velocity results in melt falling backunder gravity at higher speed. The falling velocity is the main factor of oxide film entrainment in vacuum suction casting. The designcriterion of depressurizing rate was deduced, and the A356 alloy castings were poured to test the formula. The four-point bend testand Weibull probability plots were applied to assessing the fracture mechanisms of the as-cast A356 alloy. The results illuminate amethod on designing suitable depressurizing speed for mold filling in vacuum suction casting.

基于ProCAST的一模多腔YL112铝合金压铸件数值模拟及工艺优化

针对YL112压铸铝合金一模多铸产品的组织性能均一性需求,采用ProCAST软件对典型一模多铸工艺进行模拟,比较了两种不同充型顺序的压铸方案。结果表明:基于顺序凝固一模多腔压铸件由于充型与凝固过程的温度场分布不均,导致近浇口端铸件出现明显缩松缩孔缺陷,造成铸件性能均一性差。后续采用等流程浇注系统,实现一模多腔铸件同时充型凝固过程,改善了铸件温度场分布,减少了工艺缺陷。经过实际生产验证,获得了组织性能均一性好的压铸件。

Low-cycle fatigue behavior of permanent mold cast and die-cast Al-Si-Cu-Mg alloys

Fatigue failure is one of the main failure forms of Al-Si-Cu-Mg aluminum alloys. To feature their mechanical aspect of fatigue behavior, the low-cycle fatigue behavior of permanent mold cast and die-cast AI-Si- Cu-Mg alloys at room temperature was investigated. The experimental results show that both permanent mold cast and die-cast AI-Si-Cu-Mg alloys mainly exhibit cyclic strain hardening. At the same total strain amplitude, the diecast AI-Si-Cu-Mg alloy shows higher cyclic deformation resistance and longer fatigue life than does the permanent mold cast AI-Si-Cu-Mg alloy. The relationship between both elastic and plastic strain amplitudes with reversals to failure shows a monotonic linear behavior, and can be described by the Basquin and Coffin-Manson equations, respectively.

AnyCasting模拟软件在摩托车铝合金轮毂模具设计中的应用

AnyCasting模拟软件,在重力金属模具设计中,通过后处理模块,能直观模拟出铸造生产过程中气孔、缩松、缩孔等缺陷的分布,以对铸造缺陷准确预测,有利于模具设计和铸造工艺的改进,避免了无谓的模具修改,提高了试模的成功率,大大缩短了新品开发周期,降低了试模费用,产品质量得到了保障。