High frequency shock load is often generated during pyrotechnic device working, which is detrimental to spacecraft structures and electric devices. Therefore, it is valuable to reduce the shock load in pyrotechnic dev...High frequency shock load is often generated during pyrotechnic device working, which is detrimental to spacecraft structures and electric devices. Therefore, it is valuable to reduce the shock load in pyrotechnic device design. Actually, there are several ways to decrease pyroshock loads, such as reduction of powder,installation of buffering structure, insulation of damageable devices, and so on. Considered assuring the function of pyrotechnic device and minimum of structure modification, shock absorbing structure is more propitious to be introduced in pyrotechnic device. In this paper, based on the method of thinwalled metal tube diameter-expanding, a thin-walled tube shock buffering structure was designed on a separate bolt. Built on the simplified structure of a separate bolt, the model of cone piston impacting thin-walled tube absorber was established, and the thin-walled tube shock absorbing characteristics and the relation between cone angles and absorber performance were analyzed. The results showed that the change of buffering force of thin-walled tube could be divided into four phases, and each phase was correspondent to the cone piston structure. In addition, as the cone angle increases, the max shock acceleration changes in the style of decrease-increase-decrease-increase, which is the result of coupled effects of cone piston max enter depth, buffering force and energy loss. In short, these results could establish the relationships between thin-walled tube absorbing performance and its structure, which is of significance to develop low-shock pyrotechnic device.展开更多
Sheet-bulk metal forming(SBMF)is a promising process for manufacturing complex sheet components with functional elements.In this study,the entire forming process for a typical thin-walled component with external geari...Sheet-bulk metal forming(SBMF)is a promising process for manufacturing complex sheet components with functional elements.In this study,the entire forming process for a typical thin-walled component with external gearing is investigated,including sheet forming and bulk forming processes.Deep drawn cups are prepared during sheet forming;subsequently,upsetting is performed on the sidewall to form external gearing.The upsetting method performed is known as upsetting with a controllable deformation zone(U-CDZ).Compared with the conventional upsetting method,a floating counter punch with a counter force is used in the U-CDZ method such that the forming mechanism is changed into the accumulation of the deformation zone instead of deformation throughout the entire sidewall.The effects of the counter force and material flow are investigated to understand the mechanism.The forming quality,i.e.,the formfilling and effective strain distribution,improved,whereas a high forming load is avoided.In addition,a punch with a lock bead is used to prevent folding at the inner corner during the experiment.展开更多
Metal droplet deposition is a kind of additive manufacturing(3D Printing)technique that fabricates near-net part through droplets deposition with lower cost and higher efficiency.This paper proposed a solution to prob...Metal droplet deposition is a kind of additive manufacturing(3D Printing)technique that fabricates near-net part through droplets deposition with lower cost and higher efficiency.This paper proposed a solution to problems of electric power fittings that large inventories,high procurement costs,low manufacturing efficiency and transportation cost.Using additive Manufacturing technique-metal droplet deposition,electric power fittings fabricated on power construction site.This paper describes the manufacturing process of typical thin-walled samples(the structure optimized based on additive manufacturing principle)and ball head rings of electric power fittings.Aiming at the integral AM forming for ball and ball socket electric power fitting workpiece,a novel easy removal forming support material(ceramics and gypsum mixed with UV cured resin)have been developed.Here this support material was used to fabricate nested integral workpieces.Dimensional accuracy and microstructure of the test pieces were analyzed.The error of the height and width of the forming workpiece is within 5%.No obvious overlap trace(such as overlap line and cracks)observed,and the internal microstructure is equiaxial crystal.The average density of the component is 99.51%,which measured by drainage method and 13.39%higher than the cast raw material.展开更多
文摘High frequency shock load is often generated during pyrotechnic device working, which is detrimental to spacecraft structures and electric devices. Therefore, it is valuable to reduce the shock load in pyrotechnic device design. Actually, there are several ways to decrease pyroshock loads, such as reduction of powder,installation of buffering structure, insulation of damageable devices, and so on. Considered assuring the function of pyrotechnic device and minimum of structure modification, shock absorbing structure is more propitious to be introduced in pyrotechnic device. In this paper, based on the method of thinwalled metal tube diameter-expanding, a thin-walled tube shock buffering structure was designed on a separate bolt. Built on the simplified structure of a separate bolt, the model of cone piston impacting thin-walled tube absorber was established, and the thin-walled tube shock absorbing characteristics and the relation between cone angles and absorber performance were analyzed. The results showed that the change of buffering force of thin-walled tube could be divided into four phases, and each phase was correspondent to the cone piston structure. In addition, as the cone angle increases, the max shock acceleration changes in the style of decrease-increase-decrease-increase, which is the result of coupled effects of cone piston max enter depth, buffering force and energy loss. In short, these results could establish the relationships between thin-walled tube absorbing performance and its structure, which is of significance to develop low-shock pyrotechnic device.
基金Supported by National Natural Science Foundation of China(Grant Nos.51875351,51475296).
文摘Sheet-bulk metal forming(SBMF)is a promising process for manufacturing complex sheet components with functional elements.In this study,the entire forming process for a typical thin-walled component with external gearing is investigated,including sheet forming and bulk forming processes.Deep drawn cups are prepared during sheet forming;subsequently,upsetting is performed on the sidewall to form external gearing.The upsetting method performed is known as upsetting with a controllable deformation zone(U-CDZ).Compared with the conventional upsetting method,a floating counter punch with a counter force is used in the U-CDZ method such that the forming mechanism is changed into the accumulation of the deformation zone instead of deformation throughout the entire sidewall.The effects of the counter force and material flow are investigated to understand the mechanism.The forming quality,i.e.,the formfilling and effective strain distribution,improved,whereas a high forming load is avoided.In addition,a punch with a lock bead is used to prevent folding at the inner corner during the experiment.
基金This research was funded by National Natural Science Foundation of China under grant number 51575313 and 51775420.This paper got help from Du Jun and Wang Xin of Xi’an Jiaotong University.
文摘Metal droplet deposition is a kind of additive manufacturing(3D Printing)technique that fabricates near-net part through droplets deposition with lower cost and higher efficiency.This paper proposed a solution to problems of electric power fittings that large inventories,high procurement costs,low manufacturing efficiency and transportation cost.Using additive Manufacturing technique-metal droplet deposition,electric power fittings fabricated on power construction site.This paper describes the manufacturing process of typical thin-walled samples(the structure optimized based on additive manufacturing principle)and ball head rings of electric power fittings.Aiming at the integral AM forming for ball and ball socket electric power fitting workpiece,a novel easy removal forming support material(ceramics and gypsum mixed with UV cured resin)have been developed.Here this support material was used to fabricate nested integral workpieces.Dimensional accuracy and microstructure of the test pieces were analyzed.The error of the height and width of the forming workpiece is within 5%.No obvious overlap trace(such as overlap line and cracks)observed,and the internal microstructure is equiaxial crystal.The average density of the component is 99.51%,which measured by drainage method and 13.39%higher than the cast raw material.
