北宋定窑茶叶末釉的微观结构与矿物形态学研究

茶叶末釉古瓷作为最早出现的结晶釉之一,开展深入研究可明确其矿物晶体特征、呈色机理以及古代烧制工艺,丰富古陶瓷数据库。目前相关研究多来源于二十世纪末,样本稀少且囊括的年代和窑口严重不足,所用科学仪器多已淘汰,亟需更多实验分析与数据支撑。本文采用光学显微镜(OM)、激光剥蚀电感耦合等离子体质谱(LA-ICP-MS)、扫描电镜-能谱(SEM-EDS)、激光共聚焦拉曼光谱(LRS)、飞行时间二次离子质谱(ToF-SIMS)等现代科学仪器对北宋定窑茶叶末釉样本中矿物晶体开展了分析和表征。结果表明,釉中主晶相与辽金龙泉务窑一致,为钙长石和辉石;釉面整体表现为酱-黑色釉基质富铁(Fe2O3含量均值9.73%)和矿物结晶富铁(Fe2O3含量均值11.33%),除α-Fe2O3和Fe3O4晶体等熔后重结晶矿物,还有铁镁尖晶石、残余高岭石等未融熔矿物,反演出制釉原料中有镁的加入以及烧成温度可能低于1200℃,异于前人高温烧制的观点。SIMS离子成像揭示了胎釉交界处为厚约20~80μm的钙长石晶体层,而非化妆土或玻璃态的致密反应层。研究揭示了茶叶末古瓷中Fe元素不均匀富集,部分区域过饱和而析出含铁矿物晶体,釉面颜色则主要由黄褐色的矿物晶体斑点和酱-黑色玻璃基质共同组成,同时ToF-SIMS在古瓷微区原位的形貌结构和元素分析上效果显著,能够辨别钙长石、碱性长石等微米级矿物。

The effect of single-horn glaze ice on the vortex structures in the wake of a horizontal axis wind turbine

The present study experimentally investigated the effect of a simulated single-horn glaze ice accreted on ro- tor blades on the vortex structures in the wake of a hori- zontal axis wind turbine by using the stereoscopic particle image velocimetry （Stereo-PIV） technique. During the ex- periments, four horizontal axis wind turbine models were tested, and both ＂free-run＂ and ＂phase-locked＂ Stereo-PIV measurements were carried out. Based on the ＂free-run＂ measurements, it was found that because of the simulated single-horn glaze ice, the shape, vorticity, and trajectory of tip vortices were changed significantly, and less kinetic en- ergy of the airflow could be harvested by the wind turbine. In addition, the ＂phase-locked＂ results indicated that the pres- ence of simulated single-horn glaze ice resulted in a dramatic reduction of the vorticity peak of the tip vortices. Moreover, as the length of the glaze ice increased, both root and tip vortex gaps were found to increase accordingly.

Investigation on surface figuration and microstructure of laser glazed nanostructure zirconia thermal barrier coatings

CO2 continuous wave laser beam had been applied to the laser glazing of plasma sprayed nanostructure zirconia thermal barrier coatings. The effects of laser glazing processing parameters on the surface figuration and microstructure change had been carried out, the microstructure and phase composition of the coatings had been evaluated by the scanning electron microscope （ SEM） and the X-ray diffraction （ XRD ）. SEM observation indicates that the microstructure of the as-glazed coating could be altered from singlecolumnar structure to a combination of the columnar grain and fine equiaxed grain with the different laser glazing conditions. XRD analysis illustrates that the predominance phase of the us-glazed coating is the metastable tetragonal phase, and the glazed coating with the single columnar structure has shown the clear orientation in （220） and （400） peaks while the other coatings do not show that.

Effect of Fly Ash on Drying Shrinkage of Thermal Insulation Mortar with Glazed Hollow Beads

Drying shrinkage of thermal insulation mortar with glazed hollow beads was measured by a vertical length comparator, and the influences of fly ash with different contents（0, 18%, 36%, and 54% were used） on the long-term drying shrinkage were discussed. The mass loss was measured by the weighting method and the pore structure was characterized using three different methods, including the light microscopy, the mercury intrusion porosimetry（MIP）, and the nitrogen adsorption/desorption（NAD） experiments, and the correlations among them were researched. The results show that drying shrinkage process of thermal insulation mortar includes three steps with increasing curing time： the acceleration period（before 7 d）, the deceleration period（7-365 d）, and the metastable period（after 365 d）. Drying shrinkage in the first stage（7 d before） increases quickly owing to the fast water loss, and its development in the last two stages is attributed to the increment of the pore volume of mortar with the radius below 50 nm, especially the increment of the pore volume fraction of the pore radius within the size range between 7.3 nm and 12.3 nm. There is no change in the drying shrinkage development trend of mortar with fly ash addition, and three steps in the service life, but fly ash addition in the mortar restrains its value. There is a linear relationship between the drying shrinkage and fly ash content, which means that drying shrinkage reduces with fly ash addition.

A Novel Infrared Radiant Glaze Exhibiting Antibacterial and Antifungal Functions

Infrared radiant powder was synthesized by conventional ceramic processing techniques by using Fe2 O3, MnO2, CuO, Co2 O3 and kaolin as raw materials. A novel infrared radant glaze was developed by introducing the infrared radiant powder into glazing as a functional additive. Infrared radiant characteristics of the powder and the glaze were investigated. The optimum content of infrared radiant powder in glazing was ascertained to be 5% . The infrared radiant glaze exhibits significant antibacterial and antifungal Junctions due to the thermal effect of infrared radiation. Antibacterial percentages of the glaze reach 91% - 100% when Escherichia coli, Staphylococcus aureus and Bacillus subtilis are used as model bacterium respectively, while antifungal percentage of the glaze exceeds 95% when Penicillum citrinum is used as model fungus.

Low Crosstalk Three-Color Infrared Detector by Controlling the Minority Carriers Type of InAs/GaSb Superlattices for Middle-Long and Very-Long Wavelength

We report a type-Ⅱ InAs/GaSb superlattice three-color infrared detector for mid-wave （MW）, long-wave （LW）, and very long-wave （VLW） detections. The detector structure consists of three contacts of NIPIN architecture for MW and LW detections, and hetero-junction NIP architecture for VLW detection. It is found that the spectral crosstalks can be significantly reduced by controlling the minority carriers transport via doping beryllium in the two active regions of NIPIN section. The crosstalk detection at MW, LW, and VLW signals are achieved by selecting the bias voltages on the device. At 77K, the cutoff wavelengths of the three-color detection are 5.3μm （at OmV）, 141μm （at 300mV） and 19μm （at -20mV） with the detectivities of 4.6xlO11 cm.Hzl/ZW-1, 2.3×10^10 cm.Hzl/2W-1, and 1.0×10^10cm.Hzl/2W-1 for MW, LW and VLW. The crosstalks of the MW channel, LW channel, and VLW channel are almost 0, 0.25, and 0.6, respectively.

Preparation of Lead-free Base Glaze Suitable for Pearlescent Pigments by Low-temperature Solid-phase Reaction with Alkali Waste

A lead-free base glaze suitable for pearlescent pigments was prepared by a low-temperature solid-phase reaction with alkali waste.Tests were performed to evaluate the effects of the sintering conditions and alkali waste composition on the prepared base glaze and pearlescent glaze.The experimental results show that partially replacing SiO_(2) with B_(2)O_(3) effectively reduced the sintering temperature and time to form a glass network,but the network structure becomes disconnected as the B_(2)O_(3) content increases.An amorphous base glaze was obtained when soda ash was replaced with a small amount of alkali waste,but increasing the addition of NaCl further was adverse to base glaze formation by resulting in crystallization of the base glaze and a decrease in the bridging oxygen content.The pearlescent pigment was thermally stable in the glaze at 750℃,while higher temperatures caused the crystalline phase of NaAlSiO_(4) to appear and adhere to the surface of pigment granules,which degraded the pearlescent effect of the glaze.

Application of cetylpyridinium chloride in dispersion of antibacterial ceramic glaze

The adsorption of cetylpyridinium chloride(CPC)onto a ceramic glaze mixture composed of limestone,feldspar,quartz,kaolin,and antibacterial agent was studied.Both adsorption isothermals and the average particle zeta potential were investigated in order to understand the suspension stability as a function of pH,ionic strength,and surfactant concentration.The results show that under the optimal conditions such as pH value of 7 or 9,0.01 mol/L of ionic strength and around critical micelle concentration(CMC)of surfactant,antibacterial ceramic glaze acquires fine dispersion stability.The adsorption of CPC on ceramic glaze particles is in accordance with Langmuir model in 0.01mol/L at pH=7 and pH=9.The adsorption of small amounts of cationic CPC onto the primarily negatively charged surfaces of the particles in the pH range of 7?9 produces strong attraction and flocculation due to hydrophobic interactions.High concentration of surfactant under 0.01 mol/L of salt provides high zeta potential,which produces a high stability.

A New Ceramic Substrate Glaze with High Resistance to Molten Aluminum

Corrosion resistance of ceramic substrate glazes to molten aluminum was studied in this paper. The glazes can spread slightly in aluminum alloy according to SEM examination of solidified interface between the glazes and aluminum alloy. The components of B2O3-P2O5 glazes were not detected with electron probe at the side of aluminum alloy near the interface, but the components of boron-free glaze were detected. It is shown that borophosphate glazes can resist the corrosion of molten aluminum.

Complex Impedance Spectra Analysis of SnO_2-glaze Composites

SnO2-glaze composites were prepared by Sb-doped SnO2 and SiO2-CaO-Al2O3-B2O3 glaze. The composites changed from an electrical insulator to a conductor as the SnO2 content increased from Owt% to 90 wt% . The complex impedance spectra of the fabricated composites were investigated in the frequency range of 100Hz-40 MHz and three kinds of typical shape of complex impedance spectra were recorded and analyzed. The ,spectrum is quite close to the model of conduction via nonohmic contactiug when the SnO2 content is relatively low, In high loading region, the spectrum shows the conduction pattern through ohmic contact chains . In the moderate loading region, the model is a mixture of the above two models. Equivalent circuit of the composite changes from resistor-capacitor circuit to resistor-inductor circuit as the content of SnO2 increases.

Influence of Rare Earth Composite Phosphate on Surface Free Energy of Ceramic Glaze

Rare earth composite phosphate (RECP) was doped into the ceramic glazes. The contact angle and surface free energy were characterized by the OCA-30 automatism contact angle test system. Through studied the influence of RECP on the surface free energy of ceramic glaze and movement modality of oil on the ceramic glaze in the water, the results show that the ceramic surface free energy increase obviously after dope RECP. Analysis and calculation show that the surface free energy increase mainly profited from the surface hydroxyl groups increase.

A Study of Ca-Mg Silicate Crystalline Glazes——An Analysis on Forms of Crystals

In the study on Ca-Mg silicate crystalline glazes, we found some disequilibrated crystallization phenomena, such as non-crystallographic small angle forking and spheroidal growth, parasitism and wedging-form of crystals, dendritic growth, secondary nucleation, etc. Those phenomena possibly resulted from two factors: (1) partial temperature gradient, which is caused by heat asymmetry in the electrical resistance furnace, when crystals crystalize from silicate melt; (2) constitutional supercooling near the surface of crystals. The disparity of disequilibrated crystallization phenomena in different main crystalline phases causes various morphological features of the crystal aggregates. At the same time, disequilibrated crystallization causes great stress retained in the crystals, which results in cracks in glazes when the temperature drops. According to the results, the authors analyzed those phenomena and displayed correlative figures and data.

Research on the Application in Glazed Tile Heating of the Low-Carbon Catalytic Combustion Furnace of Natural Gas

This experiment aims to summarize the regular pattern of low-carbon catalytic combustion furnace of natural gas used in glazed tile heating. The tiles used for decorating which are heated by catalytic combustion furnace are more fine and glossy than the conventional ones, moreover, pollutant emission produced in productive process is much less than before. This conclusion may provide a new way to glazed tile heating industry, and at the same time, provide a general method of using the catalytic combustion furnace.

Lime-Barium and Lime-Zinc Raw Glazes with Raw Materials from Tanzania and Cameroon

In the paper, the lime-barium and lime-zinc glazes used in Southern and Eastern Africa Mineral Center (SEAMIC) ceramic unit in Tanzania were investigated for the production of high temperature raw glazes in Cameroon. The base Seger formula used was 0.3KNaO, 0.3CaO, 0.4ZnO or BaO;xAl2O3 and ySiO2. Different Al2O3/SiO2 formula ratios for glossy and matt glazes were tested with raw materials from Cameroon and Tanzania. In the Cameroonian glazes, a local pegmatite (quartz, microcline, albite) with low coloured oxides replaced an albitic feldspar in the Tanzanian glazes. The other materials were kaolin, limestone, silica and barium carbonate or zinc oxide. The glazes were tested at Seger Cone 7 (1240℃) on stoneware slabs (made up of the same feldspathic glaze material: 18%, silica sand or quartz 27%, ball clay 40% and kaolin 15%) from both Tanzania and Cameroon materials. From results obtained, zinc oxide acted as a more vigorous flux than barium carbonate at cone 7, which is obvious in the glazes with pegmatite (with high quartz content). At a Seger formula of Al2O3/SiO21:10, transparent glazes were obtained. In these glazes the alumina content was lower and when increased to higher Seger ratios 1:4.7 - 8.7, the gloss was lowered to matt-luster due to fine crystal formation.

Isolated attosecond pulse generation from atom radiated by a three-color laser pulse

We theoretically investigate high-order harmonic and attosecond pulse generation from helium atom in a three-color laser field, which is synthesized by 10 fs/800 nm Ti-sapphire laser and a two-color field consisting of 30 fs/532 nm and 30 fs/1330 nm pulses. Compared with harmonic spectrum generated by a monochromatic field, the harmonics generated from the synthesized three-color field show a supercontinuum spectrum with a bandwidth of 235 eV, ranging from the 154th to the 306th order harmonic. This phenomenon can be attributed to the fact that the ionization of atoms as well as motion of ionized electron can be effectively controlled in the three-color field. Therefore, an isolated 46-as pulse can be generated by superposing supercontinuum from the 160th to the 210th order harmonics.

The Glazed Tile Techniques of the Seljuk and Beylik Periods

The word ＂tile＂ originates from Persian and means ＂China＂ or ＂Chinese work＂. In the Ottoman language, the word ＂tile＂ also means ＂Chinese work＂, or ＂belonging to China＂. The art of Turkish tiles occupies a place of prominence in the history of Islamic art. Its roots can be traced at least as far back as the Uygurs of the eighth and ninth centuries. Its subsequent development was influenced by the Karakhanids, the Ghaznavids, and （especially） Iranian Seljuk art. With the Seljuks＇ victory over the Byzantines at Malazgirt in 1071, the art followed them into Anatolia and embarked upon a new period of strong development fostered by the Anatolian Seljuk sultanate. The first major development in the art of tile-making occurred primarily in Anatolian Seljuk architecture. Various techniques have been used in the art of tiles which gave hundreds of samples for centuries. This study explores the glazed tile techniques used in the production of the S elj uk and Beylik periods.

Creating Matte and Opaque Stable Colored Glazes on Local Omani Earthenware Pottery: Testing White Zircon Borax Frit Glaze Recipes

The ability of Omani local pottery earthenware to accept low- and medium-temperature fired glazes can face technical difficulties. The impurities included in the clays extracted from local fields, especially iron oxide, are a noted weakness that affects painting the local pottery with shiny, opaque, or matte glazes. Previously published research conducted by the researcher on Omani earthenware clays focused on finding a special transparent, shiny, and stable glazing recipe, but few studies have provided matte and opaque glazing recipes that are technically suitable for local Omani clays. By using laboratory-based experimental methodology, this research will investigate the possibility of using White Zircon Borax Frit (WZBF) to develop matte and opaque stable glazes that are suitable with local Omani pottery clay bodies. In the end of this experimental research, the purpose of this project is to develop applicable glazing recipes to be used for painting pots made by Omani clays.

The Impact of Sun Radiation on the Thermal Comfort in Highly Glazed Buildings Equipped with Floor Heating Systems

Occupants of highly glazed buildings often suffer from thermal discomfort during the mid-seasons when no shadings are used in such buildings,especially when inertial heating systems are used.The present study is devoted to evaluating the impact of long solar beam exposure on the internal thermal discomfort in glazed spaces when heating is implemented through a floor system.A comprehensive experimental study is carried out using an experimental bi-climatic chamber which is fully monitored and controlled,allowing realistic simulations of the dynamic movement of the sun patch on a heated slab.The findings show that a period of discomfort as long as 8 h can occur,and persist far after the sunbeam exposure stops.During this period,the heating slab’s surface temperature,considered from an average point of view,can attain 34°C while the indoor temperature reaches 26°C.Simulations conducted using a previously developed model display a good fit with the measurements.

Comparison of Pfizer/BioNTech BNT162b2 COVID-19 (Comirnaty) Vaccination Effects in Aged Adults with Special Consideration for the Effectiveness of the Three-Color iSpot in Assessing Immune Response

Background: The roll-out of vaccines against severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) was certainly among the fastest in medical history. Vaccination campaigns around the world began a year after the outbreak in 2019. When Austria started vaccinating the population in 2020, we took the opportunity to collect data from the first sets of patients receiving the vaccine in our study region of East Tyrol. Purpose: Many studies have been conducted examining the immunogenicity of the new vaccines using classic serological test methods in combination with an IFN-γ ELISpot. Undeniable disadvantages of using IFN-γ to characterize the status of the cellular immunity are that 1) being an acute phase cytokine, IFN-γ loses signal strength in the long run and 2) IFN-γ does not provide information about the involvement of T helper 2 (Th2) cells in the immune process. This implies that it can affect false negative data about the cell-mediated immune status. Method: Therefore, in addition to a chemiluminescent immunoassay and the enzymatic IFN-γ ELISpot, this study included a fluorescent ELISpot assay using precoated human SARS-CoV-2-specific IFN-γ/IL-2/IL-5 ELISpot kits to show a more holistic overview on the involvement of T helper 1 (Th1) cells as signal senders of IL-2 and Th2 cells as senders of IL-5. Results and Conclusion: Our study confirms good immunogenicity of Pfizer/BioNTech BNT162b2 COVID-19 (Comirnaty) with strong Th1 and vanishingly small Th2 participation. The fluorescent three color iSpot can improve the diagnostic results’ significance for the individual, especially when the infection has been longer in the past and the IFN-γ signal diminishes.

Effect of heat treatment temperature of the glaze lager on the structure and the formaldehyde removal performance of an interior wall tile

With the improvement of people’s living standards,a large number of petroleum products,daily necessities and decorations that can produce volatile organic compounds are used in decoration,which seriously affects the indoor air quality.Interior decoration materials have become a research hotspot in recent years.The purpose of this paper is to develop a kind of interior wall material with good indoor formaldehyde removal effect,easily using,and low cost.In this paper,combining different heat treatment temperatures of the glaze layer,tourmaline/diatomite-based interior wall tiles were prepared by ultrafine grinding,solid sintering,and low temperature calcination.The glaze layer under different heat treatment temperatures was characterized by thermogravimetric-differential thermal analysis,X-ray diffraction,and scanning electron microscope.The influences of heat treatment temperature on the microscopic morphology and structure of the glaze layer were analyzed.Taking formaldehyde as the target degradation product,the effects of tourmaline/diatomite-based interior wall tiles on the removal of formaldehyde under different heat treatment temperatures of the glaze layer were investigated.The results showed that with the increase in heat treatment temperature,the original pores of diatomite decreased,the specific surface area decreased,and the structure of tourmaline changed.At 850℃,the surface structure of the material was slightly damaged,the strength was increased,and the removal effect of formaldehyde was better.In a 1 m^(3) environmental chamber,the formaldehyde removal rate reached 73.6%in 300 min.When the temperature was increased to 950℃ and above,diatomite and the structure of tourmaline were destroyed,and the ability of the material to adsorb and degrade formaldehyde decreased.