Laminated Solid Timber Slab with Transverse Prestressing Using the Strategy of Interleaved Vertical Displacement of Lamellae

This article presents a study on the structural behavior of transversely prestressed laminated timber slabs,focusing on an innovative approach:vertically misaligned lamellae.This misalignment,achieved by sliding vertically the wooden lamellae rather than aligning them,enhances the slab’s cross-section moment of inertia,thereby improving load-bearing capacity and stiffness.Testing involved two groups of structural size specimens:one with vertically aligned lamellae(control group)and the other with misaligned lamellae(study group).Results showed the study group exhibited 42%superior stiffness and 10%less load capacity compared to the control.Failures typically occurred individually in the lamellae,particularly in those with defects or lower modulus of elasticity,concentrated in the middle third of the slabs’free span where tensile stresses peak.Despite a higher number of failed lamellae,the study group demonstrated promising performance.Analysis of prestressing bar indicated no damage at all in the thread,suggesting potential for reducing bar diameter.These findings offer crucial insights into applying these slabs in timber construction as well as to any kind of construction.

Three-dimensional Analysis of Prestressed Concrete Offshore Wind Turbine Structure Under Environmental and 5-MW Turbine Loads

A concrete gravity base structure may not be suitable for offshore weak soil because of its heavy weight. Therefore, a conceptual model for a concrete offshore wind turbine structure suitable for weak soils is proposed. The proposed model is composed of a prestressed concrete(PSC) supported by a pile foundation. For a three-dimensional analysis of the large concrete structure, wave pressures based on the diffraction wave theory are developed using a three-dimensional solid finite element method. Static and dynamic analyses were performed to achieve the conceptual model of a PSC structure subjected to ocean environmental loads and a 5-MW turbine load on southwest coast in Korea. From the analysis, the maximum displacement and stresses of the proposed model did not exceed the allowable values from design standard, and the first mode of natural frequency of the structure was in a safe range to avoid resonance. The proposed model has enough structural stability to withstand external loads, and it is expected to be used in locations suitable for concrete gravity structures.

Computing of the Anchor by the Method of Three-Dimension Point-Radiate Infinite Elements

On the basis of the one-dimension infinite element theory, the coordinate translation and shape function of 3D point-radiate 8-node and 4-node infinite elements are derived. They are coupled with 20-node and 8-node finite elements to compute the compression distortion of the prestressed anchorage segment. The results indicate that when the prestressed force acts on the anchorage head and segment, the stresses and the displacements in the rock around the anchorage head and segment concentrate on the zone center with the anchor axis, and they decrease with exponential forms. Therefore,the stresses and the displacement spindles are formed. The calculating results of the infinite element are close to the theoretical results. This indicates the method is right. This article introduces a new way to study the mechanism of prestressed anchors. The obtained results have an important role in the research of the anchor mechanism and engineering application.

Design of Large-Scale Prestressing Bucket Foundation for Offshore Wind Turbines

The key in the force transmission between the tower and the foundation for offshore wind turbines is to transfer the large moment and horizontal loads. The finite element model of a large-scale prestressing bucket founda- tion for offshore wind turbines is set up and the structural characteristics of the arc transition structure of the founda- tion are analyzed for 40-60 channels(20-30 rows) arranged with prestressing steel strand under the same ultimate load and boundary conditions. The mechanical characteristics of the key parts of the foundation structures are illus- trated by the peak of the principal tensile stress, the peak of the principal compressive stress and the distribution areas where the principal tensile stress is larger than 2.00 MPa. It can be concluded that the maximum principal tensile stress of the arc transition decreases with the increasing number of channels, and the amplitude does not change signifi- cantly; the maximum principal compressive stress increases with the increasing number of channels and the amplitude changes significantly; however, for the distribution areas where the principal tensile stress is larger than 2.00 MPa, with different channel numbers, the phenomenon is not obvious. Furthermore, the principal tensile stress at the top of the foundation beams fluctuantly increases with the increasing number of channels and for the top cover of the bucket, the principal tensile stress decreases with the increasing number of channels.

Three-dimensional Computational Fluid Dynamics Modeling of Two-phase Flow in a Structured Packing Column

Characterizing the complex two-phase hydrodynamics in structured packed columns requires a power- ful modeling tool. The traditional two-dimensional model exhibits limitations when one attempts to model the de- tailed two-phase flow inside the columns. The present paper presents a three-dimensional computational fluid dy- namics （CFD） model to simulate the two-phase flow in a representative unit of the column. The unit consists of an CFD calculations on column packed with Flexipak 1Y were implemented within the volume of fluid （VOF） mathe- matical framework. The CFD model was validated by comparing the calculated thickness of liquid film with the available experimental data. Special attention was given to quantitative analysis of the effects of gravity on the hy- drodynamics. Fluctuations in the liquid mass flow rate and the calculated pressure drop loss were found to be quali- tatively in agreement with the experimental observations.

Three-Dimensional Tidal Model and Its Application to Numerical Simulation of Water Quality in Coastal Waters

The turbulence mechanism plays an important part in the mixing process and momentum transfer of turbulence. A three-dimensional Prandtl mixing length tidal model has been developed to simulate tidal flows and water quality. The eddy viscosities and diffusivities are computed from the Prandtl mixing length model. In order to model the water quality of an estuary or coastal area many interdependent processes need to be simulated. These may be conveniently separated into three main groups: transport and mixing processes, biochemical interaction of water quality variables and the utilization and re-cycling of nutrients by living matter. The model simulates full oxygen and nutrient balance, primary productivity and the transport, reaction mechanism and fate of pollutants over tidal time-scales. The model is applied to numerical simulation of tidal flows and water quality in Dalian Bay. The model has been calibrated against a limited data set of historical water quality observations and in general demonstrates excellent agreement with all available data.

Three-Dimensional and Cross-sectional Characteristics of Normal Grain Growth Based on Monte Carlo Simulation

An appropriate Monte Carlo method was developed to simulate the three-dimensional normal grain growth more completely. Comparative investigation on the three-dimensional and the cross-sectional characteristics of normal grain growth was done. It was found that the time exponent of grain growth determined from cross-section exhibits the same rule of increasing slowly with time and approaching the theoretical value n = 0.5 of steadygrain growth as the three-dimensional (3-D) system. From change of the number of grains per unit area with timemeasured in cross-section, the state of 3-D normal grain growth may be predicted. The gtain size distribution incross-section is different from that in 3-D system and can not express the evolution characteristic of the 3-D distribution. Furthermore, there exists statistical connection between the topological parameters in cross-section and thosein three-dimensions.

Three-dimensional frequency-domain full waveform inversion based on the nearly-analytic discrete method

The nearly analytic discrete(NAD)method is a kind of finite difference method with advantages of high accuracy and stability.Previous studies have investigated the NAD method for simulating wave propagation in the time-domain.This study applies the NAD method to solving three-dimensional(3D)acoustic wave equations in the frequency-domain.This forward modeling approach is then used as the“engine”for implementing 3D frequency-domain full waveform inversion(FWI).In the numerical modeling experiments,synthetic examples are first given to show the superiority of the NAD method in forward modeling compared with traditional finite difference methods.Synthetic 3D frequency-domain FWI experiments are then carried out to examine the effectiveness of the proposed methods.The inversion results show that the NAD method is more suitable than traditional methods,in terms of computational cost and stability,for 3D frequency-domain FWI,and represents an effective approach for inversion of subsurface model structures.

Effects of Prestressing of the Ring Gear in Interference Fit on Flexural Fatigue Strength of Tooth Root

When the gearbox body interference is connected to the ring gear, prestressing occurs in the ring gear, which has a significant impact on the strength and life of the gear. Research on the prestressing of the inner ring gear is in the preliminary stage, and the distribution rule of the prestressing and the influence of each parameter on the interference prestressing have not been derived. In this paper, based on the method of calculating the prestressing of the thick cylinder in interference fit, the ring gear is found to be equivalent to a thick cylinder, and the distribution rule of prestressing of the ring gear in the interference fit is inferred. Then, by modeling and analyzing the gearbox body and ring gear in the interference fit using ABAQUS, the distribution rule of prestressing the ring gear in the interference fit is obtained through a numerical simulation. Finally, the prestressing of the ring gear in the interference fit is measured using X-ray di raction, and the distribution rule of prestressing of the ring gear in the interference fit is obtained through analysis. Compared with the distribution rule of prestressing in theory, numerical simulation, and experiment, the theoretical distribution rule of prestressing is amended through a statistical method, and a more accurate formula of prestressing is obtained. Through the calculation of the stress and bending moment in the dangerous section of the ring gear through prestressing, the formula for checking the tooth root flexural fatigue strength in the interference fit prestressing is inferred. This research proposes a tooth root bending strength conditional formula for the inner ring gear of the interference fit, which serves as a guide for the design and production of the actual interference joint inner ring gear.

The three-dimension model for the rock-breaking mechanism of disc cutter andanalysis of rock-breaking forces

To study the rock deformation with three- dimensional model under rolling forces of disc cutter, by car- rying out the circular-grooving test with disc cutter rolling around on the rock, the rock mechanical behavior under rolling disc cutter is studied, the mechanical model of disc cutter rolling around the groove is established, and the the- ory of single-point and double-angle variables is proposed. Based on this theory, the physics equations and geometric equations of rock mechanical behavior under disc cutters of tunnel boring machine （TBM） are studied, and then the bal- ance equations of interactive forces between disc cutter and rock are established. Accordingly, formulas about normal force, rolling force and side force of a disc cutter are de- rived, and their validity is studied by tests. Therefore, a new method and theory is proposed to study rock- breaking mech- anism of disc cutters.

Dynamic Characteristic Mechanism of Atrial Septal Defect Using Real-Time Three-Dimensional Echocardiography and Evaluation of Right Ventricular Functions

The dynamic characteristics of the area of the atrial septal defect（ASD） were evaluated using the technique of real-time three-dimensional echocardiography（RT 3DE）, the potential factors responsible for the dynamic characteristics of the area of ASD were observed, and the overall and local volume and functions of the patients with ASD were measured. RT 3DE was performed on the 27 normal controls and 28 patients with ASD. Based on the three-dimensional data workstations, the area of ASD was measured at P wave vertex, R wave vertex, T wave starting point, and T wave terminal point and in the T-P section. The right atrial volume in the same time phase of the cardiac cycle and the motion displacement distance of the tricuspid annulus in the corresponding period were measured. The measured value of the area of ASD was analyzed. The changes in the right atrial volume and the motion displacement distance of the tricuspid annulus in the normal control group and the ASD group were compared. The right ventricular ejection fractions in the normal control group and the ASD group were compared using the RT 3DE long-axis eight-plane（LA 8-plane） method. Real-time three-dimensional volume imaging was performed in the normal control group and ASD group（n=30）. The right ventricular inflow tract, outflow tract, cardiac apex muscular trabecula dilatation, end-systolic volume, overall dilatation, end-systolic volume, and appropriate local and overall ejection fractions in both two groups were measured with the four-dimensional right ventricular quantitative analysis method（4D RVQ） and compared. The overall right ventricular volume and the ejection fraction measured by the LA 8-plane method and 4D RVQ were subjected to a related analysis. Dynamic changes occurred to the area of ASD in the cardiac cycle. The rules for dynamic changes in the area of ASD and the rules for changes in the right atrial volume in the cardiac cycle were consistent. The maximum value of the changes in the right atrial volume occurred in the end-systolic period when the peak of the curve appeared. The minimum value of the changes occurred in the end-systolic period and was located at the lowest point of the volume variation curve. The area variation curve for ASD and the motion variation curve for the tricuspid annulus in the cardiac cycle were the same. The displacement of the tricuspid annulus exhibited directionality. The measured values of the area of ASD at P wave vertex, R wave vertex, T wave starting point, T wave terminal point and in the T-P section were properly correlated with the right atrial volume（P〈0.001）. The area of ASD and the motion displacement distance of the tricuspid annulus were negatively correlated（P〈0.05）. The right atrial volumes in the ASD group in the cardiac cycle in various time phases increased significantly as compared with those in the normal control group（P=0.0001）. The motion displacement distance of the tricuspid annulus decreased significantly in the ASD group as compared with that in the normal control group（P=0.043）. The right ventricular ejection fraction in the ASD group was lower than that in the normal control group（P=0.032）. The ejection fraction of the cardiac apex trabecula of the ASD patients was significantly lower than the ejection fractions of the right ventricular outflow tract and inflow tract and overall ejection fraction. The difference was statistically significant（P=0.005）. The right ventricular local and overall dilatation and end-systolic volumes in the ASD group increased significantly as compared with those in the normal control group（P=0.031）. The a RVEF and the overall ejection fraction decreased in the ASD group as compared with those in the normal control group（P=0.0005）. The dynamic changes in the area of ASD and the motion curves for the right atrial volume and tricuspid annulus have the same dynamic characteristics. RT 3DE can be used to accurately evaluate the local and overall volume and functions of the right ventricle. The local and overall volume loads of the right ventricle in the ASD patients increase significantly as compared with those of the normal people. The right ventricular cardiac apex and the overall systolic function decrease.

Clinical Value of Stereoscopic Three-dimensional Echocardiography in Assessment of Atrial Septal Defects: Feasibility and Efficiency

Stereoscopic three-dimensional echocardiography（S-3DE） is a novel displaying technol-ogy based on real-time 3-dimensional echocardiography （RT-3DE）. Our study was to evaluate the feasibility and efficiency of S-3DE in the diagnosis of atrial septal defect （ASD） and its use in the guidance for transcatheter ASD occlusion. Twelve patients with secundum ASD underwent RT-3DE examination and 9 of the 12 were subjected to transcatheter closure of ASD. Stereoscopic vision was generated with a high-performance volume renderer with red-green stereoscopic glasses. S-3DE was compared with standard RT-3D display for the assessment of the shape, size, and the surrounding tis-sues of ASD and for the guidance of ASD occlusion. The appearance rate of coronary sinus and the mean formation time of the IVC, SVC were compared. Our results showed that S-3DE could measure the diameter of ASD accurately and there was no significant difference in the measurements between S-3DE and standard 3D display （2.89±0.73 cm vs 2.85±0.72 cm, P〉0.05; r=0.96, P〈0.05）. The appearance of coronary sinus for S-3DE was higher as compared with the standard 3D display （93.3% vs 100%）. The mean time of the IVC, SVC for S-3DE monitor was slightly shorter than that of the standard 3D display （11.0±3.8 s vs 10.3±3.6 s, P〉0.05）. The mean completion time of interven-tional procedure was shortened with S-3DE display as compared with standard 3D display （17.3±3.1 min vs 23.0±3.9 min, P〈0.05）. Stereoscopic three-dimensional echocardiography could improve the visualization of three-dimensional echocardiography, facilitate the identification of the adjacent structures, decrease the time required for interventional manipulation. It may be a feasible, safe, and efficient tool for guiding transcatheter septal occlusion or the surgical interventions.

Three-Dimensional Measurement and Reconstruction of Fabric Drape Shape

This paper introduces a new method of measuring the three-dimensional drape shape of fabrics with structural light. First, we apply parallel annular structural light to form light and shade alternating contour stripes on the surface of fabrics. We then collect the images of contour stripes using Charge Coupled Device (CCD). Subsequently, we process the images to identify the contour stripes and edges of fabrics, and obtain the fabric contour lines of curved surfaces. Finally, we apply three-dimensional curved surface modeling method based on a network of polar coordinates, and reconstruct the three-dimensional drape shape of fabrics. Experiments show that our method is effective in testing and reconstructing three-dimensional drape shape of fabrics.

Inversion of source mechanism of 1989 Loma Prieta earthquake by three-dimensional FEM Green's function

Based on three-dimensional joint finite element, this paper discusses the theory and methodology about inversionof geodetic data. The FEM and inversion formula is given in detail; also a related code is developed. By use of theGreen's function about 3-D FEM, we invert geodetic measurementS of coseismic deformation of the 1989 Ms=7. 1Loma Prieta earthquake to datermine itS source mechanism. The result indicates that the slip on the fault plane isvery heterogeneous. The maximum slip and shear stress are located about 10 kin to northwest of the eathquakesource, the stress drop is about more than 1 MPa.

Three-Dimensional Bursting Phenomena in Meander Channel

Experiments were conducted in a U-shaped open-channel flume with the intention of investigating the bursting phenomena in the meander channel. The experimental results of the secondary flow fields and the Reynolds shear stress distributions show that the velocity and velocity fluctuation in the transverse direction are not negligible. Moreover, the bursting process is investigated using the three-dimensional quadrant analysis, which is more accurate than using the traditional two-dimensional quadrant analysis for the meandering channel. It is obtained from the experimental results that the internal group of events occurs more frequently than the external group, particularly the internal ejection and internal sweep events. In addition, the transition probabilities of the movements, which are defined as the changes of events from the current situation to the next situation in a time series, show that the stable organizations of events are the most possible movements, whereas the cross organizations of events have the least possible movements.

A three-dimensional digital visualization model of cervical nerves in a healthy person

Three-dimensional reconstruction nerve models are classically obtained from two-dimensional images of ＂visible human＂ frozen sections. However, because of the flexibility of nerve tissues and small color differences compared with surrounding tissues, the integrity and validity of nerve tissues can be impaired during milling. Thus, in the present study, we obtained two-dimensional data from a healthy volunteer based on continuous CT angiography and magnetic resonance myelography. Semi-automatic segmentation and reconstruction were then conducted at different thresholds in different tissues using Mimics software. Small anatomical structures such as muscles and cervical nerves were reconstructed using the medical computer aided design module. Three-dimensional digital models of the cervical nerves and their surrounding structures were successfully developed, which allowed visualization of the spatial relation of anatomical structures with a strong three-dimensional effect, distinct appearance, clear distribution, and good continuity, precision, and integrality. These results indicate the validity of a three-dimensional digital visualization model of healthy human cervical nerves, which overcomes the disadvantages of milling, avoids data loss, and exhibits a realistic appearance and three-dimensional image.

Multi-Quality Properties Capability Analysis for Prestressing Strand of Prestressed Concrete

Prestressed concrete structures are main conformati on for the construction of high way bridges. The quality of prestressed concrete s tructures is mainly affected by the tensile strength of prestressing strand. In order to attain the purpose of economic design and long life span of prestressin g strand, the less relaxation property of strand type is suitable for constructi on and usage. Thus, the research and development of prestressing strand is requi red to reach the goals of high tensile strength and low relaxation. To ensure th e required quality of prestressing strand, the strand pull test and long period relaxation test are two important items for the quality assurance. There are thr ee specific items of the tensile strength test are belong to larger-the-better quality type. The quality type of smaller-the-better is for the long period r elaxation test. However, many existing methods are able to measure process capab ility for product with single quality characteristic and cannot be applied to mo st products with multiple properties. Thus, the indices of C pu and C pl, for larger-the-better and smaller-the-better quality type respec tively proposed by Kane, are quoted and combined to propose a new index to evalu ate the quality of multiple characteristics of prestressing strand in this paper . Then, the principle of statistics is used to derive the one-to-one mathemati cal relationship of this new index and ratio of tallied. Finally, the procedure and criteria to evaluate the quality of prestressing strand is proposed. This in tegrated multi-quality property capability analysis model can be used to evalua te the multi-process capabilities and provide continuous improvement on manufac turing process of prestressing strand.

Experimental Study on the Wavelengths of Two-Dimensional and Three-Dimensional Freak Waves

Freak waves are commonly characterized by strong-nonlinearity, and the wave steepness, which is calculated from the wavelength, is a measure of the degree of the wave nonlinearity. Moreover, the wavelength can describe the locally spatial characteristics of freak waves. Generally, the wavelengths of freak waves are estimated from the dispersion relations of Stokes waves. This paper concerns whether this approach enables a consistent estimate of the wavelength of freak waves. The two-(unidirectional, long-crested) and three-dimensional(multidirectional, shortcrested) freak waves are simulated experimentally through the dispersive and directional focusing of component waves, and the wavelengths obtained from the surface elevations measured by the wave gauge array are compared with the results from the linear, 3rd-order and 5th-order Stokes wave theories. The comparison results suggest that the 3rd-order theory estimates the wavelengths of freak waves with higher accuracy than the linear and 5th-order theories. Furthermore, the results allow insights into the dominant factors. It is particularly noteworthy that the accuracy is likely to depend on the wave period, and that the wavelengths of longer period freak waves are overestimated but the wavelengths are underestimated for shorter period ones. In order to decrease the deviation, a modified formulation is presented to predict the wavelengths of two-and three-dimensional freak waves more accurately than the 3rd-order dispersion relation, by regression analysis. The normalized differences between the predicted and experimental results are over 50% smaller for the modified model suggested in this study compared with the 3rd-order dispersion relation.

A novel trilinear decomposition algorithm:Three-dimension non-negative matrix factorization

Non-negative matrix factorization （NMF） is a technique for dimensionality reduction by placing non-negativity constraints on the matrix. Based on the PARAFAC model, NMF was extended for three-dimension data decomposition. The three-dimension nonnegative matrix factorization （NMF3） algorithm, which was concise and easy to implement, was given in this paper. The NMF3 algorithm implementation was based on elements but not on vectors. It could decompose a data array directly without unfolding, which was not similar to that the traditional algorithms do, It has been applied to the simulated data array decomposition and obtained reasonable results. It showed that NMF3 could be introduced for curve resolution in chemometrics.

Neutron-induced single event upset simulation in Geant4 for three-dimensional die-stacked SRAM

Three-dimensional integrated circuits(3D ICs)have entered into the mainstream due to their high performance,high integration,and low power consumption.When used in atmospheric environments,3D ICs are irradiated inevitably by neutrons.In this paper,a 3D die-stacked SRAM device is constructed based on a real planar SRAM device.Then,the single event upsets(SEUs)caused by neutrons with different energies are studied by the Monte Carlo method.The SEU cross-sections for each die and for the whole three-layer die-stacked SRAM device is obtained for neutrons with energy ranging from 1 MeV to 1000 MeV.The results indicate that the variation trend of the SEU cross-section for every single die and for the entire die-stacked device is consistent,but the specific values are different.The SEU cross-section is shown to be dependent on the threshold of linear energy transfer(LETth)and thickness of the sensitive volume(Tsv).The secondary particle distribution and energy deposition are analyzed,and the internal mechanism that is responsible for this difference is illustrated.Besides,the ratio and patterns of multiple bit upset(MBU)caused by neutrons with different energies are also presented.This work is helpful for the aerospace IC designers to understand the SEU mechanism of 3D ICs caused by neutrons irradiation.