Study of three-dimensional spatial diffuse discharge in contact electrode structure applied to air purification

In this work,based on the role of pre-ionization of the non-uniform electric field and its effect of reducing the collisional ionization coefficient,a diffuse dielectric barrier discharge plasma is formed in the open space outside the electrode structure at a lower voltage by constructing a three-dimensional non-uniform spatial electric field using a contact electrode structure.The air purification study is also carried out.Firstly,a contact electrode structure is constructed using a three-dimensional wire electrode.The distribution characteristics of the spatial electric field formed by this electrode structure are analyzed,and the effects of the non-uniform electric field and the different angles of the vertical wire on the generation of three-dimensional spatial diffuse discharge are investigated.Secondly,the copper foam contact electrode structure is constructed using copper foam material,and the effects of different mesh sizes on the electric field distribution are analyzed.The results show that as the mesh size of the copper foam becomes larger,a strong electric field region exists not only on the surface of the insulating layer,but also on the surface of the vertical wires inside the copper foam,i.e.,the strong electric field region shows a three-dimensional distribution.Besides,as the mesh size increases,the area of the vertical strong electric field also increases.However,the electric field strength on the surface of the insulating layer gradually decreases.Therefore,the appropriate mesh size can effectively increase the discharge area,which is conducive to improving the air purification efficiency.Finally,a highly permeable stacked electrode structure of multilayer wire-copper foam is designed.In combination with an ozone treatment catalyst,an air purification device is fabricated,and the air purification experiment is carried out.

A novel coating technology for fast sealing of air leakage in underground coal mines

Air leakage in underground coal mines presents a serious hazard for coal production and the safety of miners.Coating technology is commonly used as an efficient means for preventing air leakage.To address existing problems with high dust concentrations in large operations involving complex processes and the high cost of traditional coating technology,a novel coating technology that ensures intrinsic safety by utilizing water pressure and wind pressure was developed.This new coating technology was designed to suction and spray,and the technical parameters of its spray performance was also studied.The experimental tests and evaluation indicated the optimum working range is 0.3–0.7 MPa of wind pressure,1.2–10.2 L/min of water quantity,and 1.0–3.5 m of spraying distance.Moreover,this novel coating technology was tested in the Dashuitou Coal Mine in Gansu Province of China.Compared with conventional counterparts,the proposed new technology is safe,efficient,and convenient to operate.During spraying,dust concentrations were kept at less than 10 mg/m3,and the average rebound ratio resilient rate of solid materials was below 13%.After spraying,the average leakage every 100 m was 4 m3/min,and the oxygen volume fraction in the adjacent goaf was approximately 4%,demonstrating excellent air leakage prevention.

Experimental research on inorganic solidified foam for sealing air leakage in coal mines

In order to efficiently seal air leakages and control spontaneous combustion of coal, solidified foam was developed by adding a certain compound additive to fly coal ash and cement as the main materials. It was prepared basing on the foaming characteristic through physical and mechanical system. We studied the effects of the different types of foaming agents, the mass ratio of cement to fly ash, and the mass ratio of solid to water and content of cellulose on the performance of solidified foam. The results show that when adding the composite protein, surfactant and cellulose foaming agents. The cement-fly ash ratio of 0.75:1, the water solid ratio as large as 2:1, and the solidified foam with high properties and density of only 516 kg/m 3 and compressive strength of up to 12.68 MPa were prepared. But the initial setting time, identity and compressive strength may be changed by varying the water solid ratio and/or the additives. We theoretically analyzed the influence mechanism of foam density, compressive strength and water solid ratio. The solidified foam is especially suitable for sealing surface leakage channels and filling the goaf with a wide application prospects.

Numerical simulation study of gob air leakage field and gas migration regularity in downlink ventilation

Aiming at the issue that mass of gas emission from mining gob and the gas exceeded in working face, gob air leakage field and gas migration regularity in downlink ventilation was studied. In consideration of the influence of natural wind pressure to analyze the stope face differential pressure, gob air leakage field distribution and gas migration regularity theoretically. Established a two-dimensional physical model with one source and one doab, and applied computational fluid dynamics analysis software Fluent to do numerical simulation, analyzed and contrasted to the areas of gob air leakage on size and gas emission from gob to working face on strength when using the downlink ventilation and uplink ventilation. When applied downward ventilation in stope face, the air leakage field of gob nearly working face, and the air leakage intensity were smaller than uplink, this can effectively reduce the gas emission from gob to working face; when used downlink ventilation, the air leakage airflow carry the lower amount of gas to doab than uplink ventilation, and more easily to mix the gas, reduced the possibility of gas accumulation in upper comer and the stratified flows, it can provide protection to mine with safe and effective production.

An improved lumped parameter model predicting attenuation of earmuff with air leakage

Since air leakage is inevitable when earmuffs are worn improperly or together with safety glasses in factory or military,it is required to be considered to accurately predict earmuff attenuation.Besides unwanted air leakage,under controlled air leakage is introduced to earmuff to achieve adjustable attenuations in different signal-to-noise ratios(SNRs)and balance between attenuation and speech intelligibility.This work is to develop an improved lumped parameter model(LPM)to predict earmuff attenuation with consideration of air leakage.Air leakage paths are introduced into conventional LPM without air leakage,and air leakage path impedance is analytically described by Maa’s microperforated tube impedance.Earmuff passive attenuation behavior can be analytically described and analyzed with the improved LPM.Finally,the validity of improved LPM is verified experimentally.The results indicate that the improved LPM can predict earmuff attenuation with air leakage,and air leakage deteriorates earmuff attenuation and turns resonance frequency higher.

Evaluation of the Air Leakage Flowrate in Sintering Processes

Iron ore sintering is a pre-treatment technology by which orefines are converted into porous and permeable sin-ters,which are the used in blast furnaces.This process can be adversely affected by air leakage phenomena of various types.As experimental measurements are relatively difficult and often scarcely reliable,here a theoretical model based on typicalfluid-dynamic concepts and relationships is elaborated.Through the analysis of two extreme cases,namely,those in which leakage is due to a small hole or a full rupture,a generalized hole-bed mod-el is introduced,which for thefirst time also includes a complete bed permeability equation and can deal with different leakage position conditions.The results show that the model can evaluate the influence of leakage on the system at one time and be used to calculate theflowrate and pressure drop.Notably,the obtained results are within a 15%deviation with respect to available experiment values,used for comparison.

Analysis of mine's air leakage based on pressure gradient matrix between nodes

Air leakage may significantly affect the effectiveness of mine ventilation by in- creasing the cost of ventilation and arousing problems for ventilation management.Fur- thermore,air leakage may accelerate the process of coal spontaneous combustion and cause gas explosion,thus greatly threatens the safety of coal production.The estimation of air leakage,therefore,have great practical significance.For any ventilation system of coal mines,there is a defined pattern of pressure gradient which drived the mine air to flow in the network,drives possible air leakage to go shortcut as well.Air leakage may occur through ventilation structures such as ventilation doors and fractures of the surroun- dig coal and rock of airways.A concept and the relevent calculation method of the pres- sure gradient matrix was put forward to assist the analysis of potential air leakage routes. A simplified example was used to introduce the application principle of'pressure gradient matrix in identifying all the potential air leaking routes,which offers a deeper understand- ing over the ventilation system and the prevention of coal spontaneous combustion.

Energy Saving Technology for Lowering Air Leakage of Sintering Pallets and Dust Collectors in Sinter Plant

The hot-wire type anemometers were used for measuring the velocity of effective air flowing through sinter bed in this study.Meanwhile,microphones were installed beside the pathway and close to the outer sidewall of travelling pallets for monitoring sound pressure generated by an abnormal air leakage.For identifying the passing pallet,a thermal-resistant type RFID technology was adopted.Based on the measured data via anemometers,the air leakage rate of sintering machine was calculated with the mass balance method,and pallets with the abnormal leakage can be detected and ranked in the severity of leakage from the measured sound pressure with the relevant criteria.In addition,for examining the leakage situation,this study set up a capillary type of differential pressure gauge to double cone valve(DCV)below the electrostatic precipitator(EP)in sintering plant for collecting the larger dust.The criteria of determining leaked DCV and the patterns for replacing the DCV were proposed to develop a detecting and predicting system on the air leakage into dust collectors of sinter machine.It offered field staff a basis of maintaining or renewing DCV via a warning reminding and reducing air leakage to increase EP efficiency for avoiding the dust emission from the stack.These technologies had been implemented in the sintering plants of China Steel Corporation,and they can effectively reduce the air leakage rate by5%at least and further decrease the electricity consumption of the suction fan and coke rate,increase the production for the sintering machine.

Pre-placement of adhesive tape around wound sites can prevent air leakage in negative pressure wound therapy procedures

The introduction of negative pressure wound therapy has revolutionized the management of complicated wounds.However,the maintenance of an effective negative pressure environment is difficult in some instances,such as wounds in close proximity to an intestinal stoma or wounds surrounded by external fixations.We found that adhesive tape adheres more easily to itself than to wet skin or uneven surfaces.Therefore,we placed adhesive tape around surgical wounds prior to covering them with foam and sealing them with more tape.As a result of the strong adhesive force between pieces of tape,this method could provide a better environmental seal,even in situations where space is limited.Pre-placed adhesive tape around the wound site prior to foam placement could provide sufficient adhesion to maintain a continuous negative pressure environment during treatment.

Cause Analysis and Treatment Measures for Leakage of Top Cover of 330kV GIS Equipment

Based on the experience of GIS equipment maintenance, the causes of air leakage defects of GIS equipment running in a 330 substation were analyzed. After the equipment was disassembled, the main causes of air leakage were found, and a series of improvement measures were taken to eliminate the GIS equipment leakage defect. And the effective and feasible advice was put forward for this type of air leakage problem. The results lay a foundation for the safe and stable operation of GIS equipment.

Evaluation of Micro Leakage of Two Direct Esthetic Restorations with Different Preparation Techniques

Objectives: In recent times, the term “minimal intervention dentistry” has coined to describe a new approach to the treatment of the disease of caries. This study was carried out to evaluate the marginal integrity of class V cavity in permanent posterior teeth prepared with different air abrasion parameters compared with classical rotary cavity preparation. Methods: A total number of 150 sound caries for free human posterior teeth were used in this study. Teeth were extracted for periodontal disease or orthodontic reasons and the average age of patients between 20 - 35 years. Teeth were divided according to the type of restoration into two main groups: Group I (n = 75) restored with low shrinkable posterior composite (P90) and Group II (n = 75) restored with Ketac nano ionomer (N100). Each main group was divided into five groups (n = 15), then each group was further subdivided into three subgroups (n = 5) according to the storage time (immediately, three months, and six months). All teeth would be tested at both occlusal and gingival margins of prepared class V cavity according to the method of cavity preparation. Results: A high significant difference was found in the mean ranks of micro-leakageat both occlusal enamel and gingival dentin walls among Groups 1 - 5 (p-value of Conclusion: Low shrinkable silorane based composite yielded better results of micro-leakage scores along the occlusal enamel and gingival dentin walls when the cavity of class V was prepared with air abrasion technique with large size alumina particles under high pressure at immediate storage time as compared with Ketac N100.

Flow and Leakage Characteristics in Sealing Chamber of a Variable Geometry Hypersonic Inlet

When the variable geometry hypersonic inlet is sealed with ceramic wafers,the cavity flows inside the sealing chamber can be affected by the boundary layer near the side wall.To study the influence of the boundary layer thickness near the side wall on the flow and leakage characteristics in sealing chamber,the numerical calculation of the cavity flow in the sealing chamber under different inflow boundary layer thicknesses is carried out.The results show that three-dimensional cavity flow structures are close to being asymmetric,and the entrance pressure of the leakage path can also be affected by asymmetry;with the increase of the thickness of the boundary layer,the pressure at the cavity floor and the seal entrance decreases.Finally,the existing leakage prediction model is modified according to the distribution rule of the cavity floor and the flow properties in the leakage path.

Numerical Experiments on Indoor Air Quality Considering Infiltration of Mould from Crawl Space

How the air quality of crawl space influences the indoor air quality is investigated using a simulation program “Fresh 2010”, air leakage network models, and the measurement results on the mould concentrations in crawl spaces of detached houses. The annual changes of indoor mould concentrations were calculated using building models (a common wooden post-and-beam structure, improved wooden post-and-beam structure, wooden stud structure). In every structure, the concentrations in the case of exhaust ventilation system are higher than those of exhaust and supply ventilation system. The results show that it is necessary to control the air quality of crawl spaces and the infiltration from crawl spaces in order to keep indoor air quality good.

The Study of the Auto Disk Brake Air Test

In the paper weakness of air leakage system in our company is discussed firstly. Secondly the improved scheme of air leakage system including auto-control is designed. Then, the tooling with role of location and recovery is developed. At last the application of design optimization is processed. The result reveals that the system of air leakage detection is very valuable and important to manufacture.

Air Tightness Control of Passenger Car Wheels

Since the tubeless tires and especially cast alloy wheels are used, the air tightness of wheels is an important factor of the automobiles quality. Based on specification of the car industry that up to 10% decrease of the prescribed nominal tire pressure during a time of six-month is allowed, the requirements presented in specifications and norms are treated and validated. The practical experience and influences on the wheel tightness control are discussed and the data presented in a report of a wheel manufacturer, concerning the replacements of wheels in service due to air leakage are evaluated. Summarizing the results of analyses, a proposal is made for the testing of the cast aluminum car wheels to meet the requirements for a reliable and economical air tightness control in modern test facilities.

内漏测量技术中浓度衰减法应用模拟研究

核电厂主控室作为核电厂运行的关键位置,在正常和应急情况下保证工作人员在主控室可居留性尤为重要。对核电厂主控室进行可居留性内漏评价能够判断主控室环境是否处于正常安全运行状态,并根据评价结果发现主控室存在的问题进而提出解决方案,是保障主控室正常安全运行的一种评价技术手段。主控室可居留性内漏评价采用示踪气体试验方法,通过浓度衰减法在简单区域进行内漏测量技术模拟研究,结果表明:示踪气体浓度在40 min内能够达到混合均匀,各采样点示踪气体浓度相对标准偏差为3.71%,示踪气体浓度随着时间推移混合均匀性不断提高,房间空气交换次数为0.3/h,内漏量为45 m^(3)/h,空气交换次数的不确定度为0.3/h。采用浓度衰减法进行内漏测量模拟研究,通过对示踪气体注入、采样点布置,气体搅拌装置分布及示踪气体取样分析等过程进行控制,能够实现示踪气体在简单区域内快速混合均匀达到平衡状态。

矿用喷涂堵漏风自修复材料性能研究及工程应用

喷涂堵漏风是防止煤自燃的有效手段之一。针对传统水泥基喷涂堵漏风材料脆性大、易开裂、堵漏风效果差的弊端,提出以微生物及结晶矿物为自愈合剂,研制出生物胶囊和矿物胶囊以及一种生物–矿物–纤维协同自修复材料。研究了不同养护湿度和养护时间对材料裂缝自修复能力的影响。结果表明:当养护湿度为100%相对湿度、养护时间为35 d时,研制的生物胶囊和矿物胶囊可以将裂缝完全修复,裂缝最大修复宽度为1260μm。采用扫描电子显微镜(SEM)和X射线能谱仪(EDS)探究了自修复材料裂缝区域修复产物的晶型及元素组成,发现裂缝处的修复产物为球碳镁石、花瓣状的水菱镁矿以及大量由细菌矿化产生的球形方解石,这些修复产物在一定程度上起到了密闭裂缝的作用;EDS能谱分析证实了修复产物为MgCO_(3)和CaCO_(3)。当养护湿度为100%时,材料具有最高的堵漏风率(97.15%),比同养护条件的对照组试样高出73.62%。最后将自修复材料用于沿空煤柱喷涂堵漏风,结果显示该材料在6个月内未发现明显裂隙,与传统水泥砂浆相比,该材料具有更长的使用寿命和更好的预防效果。

船舶空调通风系统风管漏风量标准分析

鉴于目前船舶空调通风领域还没有一个统一的限制风管漏风量的标准,通过分析研究船舶行业常用的EUROVENT 2/2标准,并比较了GB 50243—2016、DW144和SMACNA等相关标准,对于在船舶设计、建造过程中对于空调通风系统的漏风量提出了适合我国船舶空调通风系统风管漏风量标准的建议,在设计施工过程中可采取相应手段优化和减少风管漏风量的问题,供船舶设计人员参考。

马钢2×380m^(2)烧结机节能减排实践

为进一步适应烧结生产优质、降耗、减排的发展的需求,马钢2×380m^(2)烧结机采取了一系列提质降耗技术措施。通过持续优化厚料层烧结生产经济潜力;降低固体燃耗;点火炉升级改造、带冷机改环冷机、烧结机漏风治理、大型风机变频技术等多项节能新技术的应用以及创新管理,在烧结矿质量以及节能降耗方面取得了显著改善效果,工序能耗由55 kgce/t下降至47kgce/t水平。同时对当前2×380m^(2)烧结机烧结高效、低耗生产存在的问题提出了改进方向,以进一步促进节能减排工作的持续发展。

浅埋深综放工作面采空区“三带”分布研究

为研究浅埋深综放工作面采空区“三带”分布规律,在串草圪旦煤矿6101综放工作面采空区埋设束管,对采空区“三带”进行了现场实测。实测结果表明:由于煤层埋深浅、地表起伏大、进风侧存在地表漏风,进风侧采空区“三带”明显滞后于回风侧,进回风两侧氧化带宽度分别为87.8 m和61.4 m。利用FLUENT软件对实测条件下该工作面采空区“三带”进行了数值模拟,模拟结果和现场实测结果基本一致。同时模拟了不漏风条件下该工作面采空区“三带”分布,此时采空区散热带、氧化带范围大幅度减小,进风侧采空区氧化带稍大,而工作面中部和回风侧“三带”分布基本一致。