Analytical Solutions for Testing of Baroclinic and Wind-Driven Three-Dimensional Hydrodynamic Models

It is always a challenge for a model developer to verify a three-dimensional hydrodynamic model, especially for the baroclinic term over variable topography, due to a lack of observational data sets or suitable analytical solutions. In this paper, exact solutions for the periodic forcing by surface heat flux and wind stress are given by solving the linearized equations of motion neglecting the rotation, advection and horizontal diffusion terms. The temperature at the bottom is set to a prescribed periodic value and a slip condition on flow is enforced at the bottom. The geometry of the quarter annulus, which has been extensively studied for two- and three-dimensional analytical solutions of unstratified water bodies, is used with a general power law variation of the bottom slope in the radial direction and is constant in the azimuthal direction. The analytical solutions are derived in a cylindrical coordinate system, which describes the three-dimensional fluid field in a Cartesian coordinate system. The results presented in this paper should provide a foundation for studying and verifying the baroclinic term over a varied topography in a three-dimensional numerical model.

Oxygen tension modulates cell function in an in vitro three-dimensional glioblastoma tumor model

Hypoxia is a typical feature of the tumor microenvironment,one of the most critical factors affecting cell behavior and tumor progression.However,the lack of tumor models able to precisely emulate natural brain tumor tissue has impeded the study of the effects of hypoxia on the progression and growth of tumor cells.This study reports a three-dimensional(3D)brain tumor model obtained by encapsulating U87MG(U87)cells in a hydrogel containing type I collagen.It also documents the effect of various oxygen concentrations(1%,7%,and 21%)in the culture environment on U87 cell morphology,proliferation,viability,cell cycle,apoptosis rate,and migration.Finally,it compares two-dimensional(2D)and 3D cultures.For comparison purposes,cells cultured in flat culture dishes were used as the control(2D model).Cells cultured in the 3D model proliferated more slowly but had a higher apoptosis rate and proportion of cells in the resting phase(G0 phase)/gap I phase(G1 phase)than those cultured in the 2D model.Besides,the two models yielded significantly different cell morphologies.Finally,hypoxia(e.g.,1%O2)affected cell morphology,slowed cell growth,reduced cell viability,and increased the apoptosis rate in the 3D model.These results indicate that the constructed 3D model is effective for investigating the effects of biological and chemical factors on cell morphology and function,and can be more representative of the tumor microenvironment than 2D culture systems.The developed 3D glioblastoma tumor model is equally applicable to other studies in pharmacology and pathology.

Three-dimensional structural models,evolution and petroleum geological significances of transtensional faults in the Ziyang area,central Sichuan Basin,SW China

With drilling and seismic data of Transtensional(strike-slip)Fault System in the Ziyang area of the central Sichuan Basin,SW China plane-section integrated structural interpretation,3-D fault framework model building,fault throw analyzing,and balanced profile restoration,it is pointed out that the transtensional fault system in the Ziyang 3-D seismic survey consists of the northeast-trending F_(I)19 and F_(I)20 fault zones dominated by extensional deformation,as well as 3 sets of northwest-trending en echelon normal faults experienced dextral shear deformation.Among them,the F_(I)19 and F_(I)20 fault zones cut through the Neoproterozoic to Lower Triassic Jialingjiang Formation,presenting a 3-D structure of an“S”-shaped ribbon.And before Permian and during the Early Triassic,the F_(I)19 and F_(I)20 fault zones underwent at least two periods of structural superimposition.Besides,the 3 sets of northwest-trending en echelon normal faults are composed of small normal faults arranged in pairs,with opposite dip directions and partially left-stepped arrangement.And before Permian,they had formed almost,restricting the eastward growth and propagation of the F_(I)19 fault zone.The F_(I)19 and F_(I)20 fault zones communicate multiple sets of source rocks and reservoirs from deep to shallow,and the timing of fault activity matches well with oil and gas generation peaks.If there were favorable Cambrian-Triassic sedimentary facies and reservoirs developing on the local anticlinal belts of both sides of the F_(I)19 and F_(I)20 fault zones,the major reservoirs in this area are expected to achieve breakthroughs in oil and gas exploration.

Atlantic blocking events in a simplified nonlinear baroclinic model for local finite-amplitude wave activity

为研究北大西洋阻高的形成机制,本文在局部有限振幅波活动(LWA)框架下进行了一系列数值实验.采用的数值模型能显式地描绘出两种重要的大气内部动力过程,即非线性纬向位涡通量和Rossby波包传播.模拟结果显示,这两种动力学过程均是形成大西洋阻高的重要机理.具体地,非线性纬向位涡通量和Rossby波包传播,分别是大西洋阻高南部和北部LWA形成的主导因子.因此,本研究综合了前人关于大西洋阻高的研究成果,为其形成机理提供了新的认识.

Three Dimensional Baroclinic Numerical Model for Simulating Fresh and Salt Water Mixing in the Yangtze Estuary

For simulating fresh and salt water mixing in estuaries, a three dimensional nonlinear baroclinic numerical model is developed, in which the gradients of horizontal pressure contain die gradient of barotropic pressure arising from the gradient of tidal level and the gradient of baroclinic pressure due to the gradient of salinity. The Eulerian-Lagrangian method is employed to descretize both the momentum equations of tidal motion and the equation of salt water diffusion so as to improve the computational stability and accuracy. The methods to provide the boundary conditions and the initial conditions are proposed, and the criterion for computational stability of the salinity fields is presented. The present model is used for modeling fresh and salt water mixing in the Yangtze Estuary. Computations show that the salinity distribution has the characteristics of partial mixing pattern, and that the present model is suitable for simulation of fresh and salt water mixing in the Yangtze Estuary.

DEVELOPMENT OF A HYBRID MODEL FOR THREE-DIMENSIONAL GIS

This paper presents a hybrid model for three-dimensional Geographical Information Systems which is an integration of surface- and volume-based models. The Triangulated Irregular Network (TIN) and octree models are integrated in this hybrid models. The TIN model works as a surface-based model which mainly serves for surface presentation and visualization. On the other hand, the octree encoding supports volumetric analysis. The designed data structure brings a major advantage in the three-dimensional selective retrieval. This technique increases the efficiency of three-dimensional data operation.

A three-dimensional semi-implicit unstructured grid finite volume ocean model

A new three-dimensional semi-implicit finite-volume ocean model has been developed for simulating the coastal ocean circulation, which is based on the staggered C-unstructured non-orthogonal grid in the hor- izontal direction and z-level grid in the vertical direction. The three-dimensional model is discretized by the semi-implicit finite-volume method, in that the free-surface and the vertical diffusion are semi-implicit, thereby removing stability limitations associated with the surface gravity wave and vertical diffusion terms. The remaining terms in the momentum equations are discretized explicitly by an integral method. The partial cell method is used for resolving topography, which enables the model to better represent irregular topography. The model has been tested against analytical cases for wind and tidal oscillation circulation, and is applied to simulating the tidal flow in the Bohal Sea. The results are in good agreement both with the analytical solutions and measurement results.

Three-dimensional numerical modeling of gravity anomalies based on Poisson equation in spacewavenumber mixed domain

In gravity-anomaly-based prospecting, the computational and memory requirements for practical numerical modeling are potentially enormous. Achieving an efficient and precise inversion for gravity anomaly imaging over large-scale and complex terrain requires additional methods. To this end, we have proposed a new topography-capable By performing a two-dimensional Fourier transform in the horizontal directions, threedimensional partial differential equations in the spatial domain were transformed into a group of independent, one-dimensional differential equations engaged with different wave numbers. These independent differential equations are highly parallel across different wave numbers. differential equations with different wave numbers, and the efficiency of solving fixedbandwidth linear equations was further improved by a chasing method. In a synthetic test, a prism model was used to verify the accuracy and reliability of the proposed algorithm by comparing the numerical solution with the analytical solution. We studied the computational precision and efficiency with and without topography using different Fourier transform methods. The results showed that the Guass-FFT method has higher numerical precision, while the standard FFT method is superior, in terms of computation time, for inversion and quantitative interpretation under complicated terrain.

Nonlinear Saturation of Baroclinic Instability in the Phillips Model: The Case of Energy

A conservation law for the Phillips model is derived. Using this law, the nonlinear saturation of purely baroclinic instability caused by the vertical velocity shear of the basic flow in the Phillips model—the case of energy—is studied within the context of Arnold’s second stability theorem. Analytic upper bounds on the energy of wavy disturbances are obtained. For one unstable region in the parameter plane, the result here is a second-order correction in ε to Shepherd’s; For another unstable region, the analytic upper bound on the energy of wavy disturbances offers an effective constraint on wavy (nonzonal) disturbances Φ′ i at any time.

Three-dimensional cell culture systems as an in vitro platform for cancer and stem cell modeling

Three-dimensional(3D)culture systems are becoming increasingly popular due to their ability to mimic tissue-like structures more effectively than the monolayer cultures.In cancer and stem cell research,the natural cell characteristics and architectures are closely mimicked by the 3D cell models.Thus,the 3D cell cultures are promising and suitable systems for various proposes,ranging from disease modeling to drug target identification as well as potential therapeutic substances that may transform our lives.This review provides a comprehensive compendium of recent advancements in culturing cells,in particular cancer and stem cells,using 3D culture techniques.The major approaches highlighted here include cell spheroids,hydrogel embedding,bioreactors,scaffolds,and bioprinting.In addition,the progress of employing 3D cell culture systems as a platform for cancer and stem cell research was addressed,and the prominent studies of 3D cell culture systems were discussed.

Three-Dimensional Tidal Model and Its Application to Numerical Simulation of Water Quality in Coastal Waters

The turbulence mechanism plays an important part in the mixing process and momentum transfer of turbulence. A three-dimensional Prandtl mixing length tidal model has been developed to simulate tidal flows and water quality. The eddy viscosities and diffusivities are computed from the Prandtl mixing length model. In order to model the water quality of an estuary or coastal area many interdependent processes need to be simulated. These may be conveniently separated into three main groups: transport and mixing processes, biochemical interaction of water quality variables and the utilization and re-cycling of nutrients by living matter. The model simulates full oxygen and nutrient balance, primary productivity and the transport, reaction mechanism and fate of pollutants over tidal time-scales. The model is applied to numerical simulation of tidal flows and water quality in Dalian Bay. The model has been calibrated against a limited data set of historical water quality observations and in general demonstrates excellent agreement with all available data.

A 3-DIMENSIONAL BAROCLINIC CIRCULATION MODEL OF THE TROPICAL AND NORTHERN PACIFIC

A primitive equation 3-dimensional baroclinic ocean model without the rigid-lid approximation is described.The horizontal resolution is 2.5°×2°and the vertical variations of the velocity components are resolved by 6 layers. In order to increase the allowable integration time step which is constrained by stability requirements, the vertically integrated continuity equation is linearized and both the pressure gradient terms and the Coriolis terms in the momentum equations are finite-differenced semi-implicitly.The model is applied to simulate the circulation as well as the free surface elevation and temperature patterns in the tropical and northern Pacific Ocean in both summer and winter using the wind and temperature data at the 1000 mb pressure level as input to the .model. The computed results are in general consistent with observed patterns. In particular, it is shown that the positions of the meandering axis of the Kuroshio in summer and winter are markedly different.

Charney’s Model—the Renowned Prototype of Baroclinic Instability—Is Barotropically Unstable As Well

The Charney model is reexamined using a new mathematical tool, the multiscale window transform(MWT), and the MWT-based localized multiscale energetics analysis developed by Liang and Robinson to deal with realistic geophysical fluid flow processes. Traditionally, though this model has been taken as a prototype of baroclinic instability, it actually undergoes a mixed one. While baroclinic instability explains the bottom-trapped feature of the perturbation, the second extreme center in the perturbation field can only be explained by a new barotropic instability when the Charney–Green number γ 1, which takes place throughout the fluid column, and is maximized at a height where its baroclinic counterpart stops functioning.The giving way of the baroclinic instability to a barotropic one at this height corresponds well to the rectification of the tilting found on the maps of perturbation velocity and pressure. Also established in this study is the relative importance of barotropic instability to baroclinic instability in terms of γ. When γ 1, barotropic instability is negligible and hence the system can be viewed as purely baroclinic;when γ 1, however, barotropic and baroclinic instabilities are of the same order;in fact, barotropic instability can be even stronger. The implication of these results has been discussed in linking them to real atmospheric processes.

Three-dimensional land FD-CSEM forward modeling using edge finite-element method

A modeling tool for simulating three-dimensional land frequency-domain controlled-source electromagnetic surveys,based on a finite-element discretization of the Helmholtz equation for the electric fields,has been developed.The main difference between our modeling method and those previous works is edge finite-element approach applied to solving the three-dimensional land frequency-domain electromagnetic responses generated by horizontal electric dipole source.Firstly,the edge finite-element equation is formulated through the Galerkin method based on Helmholtz equation of the electric fields.Secondly,in order to check the validity of the modeling code,the numerical results are compared with the analytical solutions for a homogeneous half-space model.Finally,other three models are simulated with three-dimensional electromagnetic responses.The results indicate that the method can be applied for solving three-dimensional electromagnetic responses.The algorithm has been demonstrated,which can be effective to modeling the complex geo-electrical structures.This efficient algorithm will help to study the distribution laws of3-D land frequency-domain controlled-source electromagnetic responses and to setup basis for research of three-dimensional inversion.

The study on three-dimensional numerical model and fronts of the Jiulong Estuary and the Xiamen Bay

Applying the methods of on-site observation and dynamic model, the research on the fronts at the Jiulong Estuary has been carried out, during which spatial and temporal distribution, dynamic characteristics and formation mechanism of salinity fronts are analyzed and discussed. The research shows that the estuarine fronts mainly lie in the area from the Jiyu Islet to the Haimen Island, outside of Yuweizai to Hulishan cross-section, the near coast of Yuweizai and the south of the Songyu-Gulangyu Channel. The fronts in the former two regions are formed directly by plume, while the one near the coast of Yuweizai is a tidal intrusion front caused by flood current and the one at the south of the Songyu-Gulangyu Channel is the result of current shear transformation. Under normal circumstances, fresh water of the Jiulong River mainly influences the inside of the Xiamen Bay, and when it is in typhoon seasons, plume front can affect the Taiwan Strait and has an effect on the biogeochemical Drocesses in the strait.

Microstructure modeling and virtual test of asphalt mixture based on three-dimensional discrete element method

The objective of this work is to model the microstructure of asphalt mixture and build virtual test for asphalt mixture by using Particle Flow Code in three dimensions(PFC^(3D))based on three-dimensional discrete element method.A randomly generating algorithm was proposed to capture the three-dimensional irregular shape of coarse aggregate.And then,modeling algorithm and method for graded aggregates were built.Based on the combination of modeling of coarse aggregates,asphalt mastic and air voids,three-dimensional virtual sample of asphalt mixture was modeled by using PFC^(3D).Virtual tests for penetration test of aggregate and uniaxial creep test of asphalt mixture were built and conducted by using PFC^(3D).By comparison of the testing results between virtual tests and actual laboratory tests,the validity of the microstructure modeling and virtual test built in this study was verified.Additionally,compared with laboratory test,the virtual test is easier to conduct and has less variability.It is proved that microstructure modeling and virtual test based on three-dimensional discrete element method is a promising way to conduct research of asphalt mixture.

Three-dimensional forward modeling for magnetotelluric sounding by finite element method

A finite element algorithm combined with divergence condition was presented for computing three-dimensional(3D) magnetotelluric forward modeling. The finite element equation of three-dimensional magnetotelluric forward modeling was derived from Maxwell's equations using general variation principle. The divergence condition was added forcedly to the electric field boundary value problem, which made the solution correct. The system of equation of the finite element algorithm was a large sparse, banded, symmetric, ill-conditioned, non-Hermitian complex matrix equation, which can be solved using the Bi-CGSTAB method. In order to prove correctness of the three-dimensional magnetotelluric forward algorithm, the computed results and analytic results of one-dimensional geo-electrical model were compared. In addition, the three-dimensional magnetotelluric forward algorithm is given a further evaluation by computing COMMEMI model. The forward modeling results show that the algorithm is very efficient, and it has a lot of advantages, such as the high precision, the canonical process of solving problem, meeting the internal boundary condition automatically and adapting to all kinds of distribution of multi-substances.

A Novel Three-Dimensional Mouse Embryonic Implantation Model In Vitro

To regenerate three-dimensional endometrium in vitro as a novel model for studying the mechanism of implantation of embryos, the luminal epithelial cells and stromal cells of the rabbit uterus were separated and cultured in vitro. The type Ⅰ mouse tail collagen was used as scaffolding material. The stromal cells were inoculated in the type I mouse tail collagen, and the luminal epithelial cells were inoculated on the type i mouse tall collagen to regenerate the endometrium in vitro. The regenerated endometrium was cultured in DMEM-F/12 media containing 100 nmol L^-1 progesterone, 10 nM β-estradiol, and 10% fetal bovine serum （FBS） for 3 d. The media were then replaced with CZB containing 100 nM progesterone, 10 nmol L-1 β-estradiol, and 10% FBS, and the mouse blastulas were co-cultured with it. The results of scanning electronic micrography showed that the epithelial cells on the surface of the reconstructed endometrium were covered with numerous slender microvilli and some epithelial cells protruded pinopodes. After culturing for 12 h with the mouse blastula, the shedding, attachment, and implantation of the blastula were observed. The blastula can escape from zona pellucida and attach to the three-dimensional endometrium and is then implanted into it. This study showed that the reconstructed three-dimensional endometrium can serve as a robust embryo implantation model in vitro.

A Three-Dimensional Water Quality Model and Its Application to Jiaozhou Bay, China

A three-dimensional coupled physical and water quality model was developed and applied to the Jiaozhou Bay to study water quality involving nutrients, biochemical oxygen demand, dissolved oxygen, and phytoplankton that are closely related to eutrophication process. The physical model is a modified ECOM-si version with inclusion of flooding/draining processes over the intertidal zone. The water quality model is based on WASP5 which quantifies processes governing internal nutrients cycling, dissolved oxygen balance and phytoplankton growth. The model was used to simulate the spatial distribution and the temporal variation of water quality in the Jiaozhou Bay for the period of May 2005 to May 2006. In addition, the effect of reduction of riverine nutrients load was simulated and evaluated. The simulated results show that under the influence of nutrients discharged from river, the concentrations of nutrients and phytoplankton were higher in the northwest and northeast of the bay, and decreased from the inner bay to the outer. Affected by strong tidal mixing, the concentrations of all state variables were vertically homogeneous except in the deeper regions where a small gradient was found. Obvious seasonal variation of phytoplankton biomass was found, which exhibited two peaks in March and July, respectively. The variation of riverine waste loads had remarkable impact on nutrients concentration in coastal areas, but slightly altered the distribution in the center of the bay.

Science Letters:Dynamic concision for three-dimensional reconstruction of human organ built with virtual reality modelling language (VRML)

This research studies the process of 3D reconstruction and dynamic concision based on 2D medical digital images using virtual reality modelling language (VRML) and JavaScript language, with a focus on how to realize the dynamic concision of 3D medical model with script node and sensor node in VRML. The 3D reconstruction and concision of body internal organs can be built with such high quality that they are better than those obtained from the traditional methods. With the function of dynamic concision, the VRML browser can offer better windows for man-computer interaction in real-time environment than ever before. 3D reconstruction and dynamic concision with VRML can be used to meet the requirement for the medical observation of 3D reconstruction and have a promising prospect in the fields of medical imaging.