Three-dimensional(3D)printing technology is increasingly used in experimental research of geotechnical engineering.Compared to other materials,3D layer-by-layer printing specimens are extremely similar to the inherent...Three-dimensional(3D)printing technology is increasingly used in experimental research of geotechnical engineering.Compared to other materials,3D layer-by-layer printing specimens are extremely similar to the inherent properties of natural layered rock masses.In this paper,soft-hard interbedded rock masses with different dip angles were prepared based on 3D printing(3DP)sand core technology.Uniaxial compression creep tests were conducted to investigate its anisotropic creep behavior based on digital imaging correlation(DIC)technology.The results show that the anisotropic creep behavior of the 3DP soft-hard interbedded rock mass is mainly affected by the dip angles of the weak interlayer when the stress is at low levels.As the stress level increases,the effect of creep stress on its creep anisotropy increases significantly,and the dip angle is no longer the main factor.The minimum value of the long-term strength and creep failure strength always appears in the weak interlayer within 30°–60°,which explains why the failure of the layered rock mass is controlled by the weak interlayer and generally emerges at 45°.The tests results are verified by comparing with theoretical and other published studies.The feasibility of the 3DP soft-hard interbedded rock mass provides broad prospects and application values for 3DP technology in future experimental research.展开更多
Three dimensional-digital image correlation （3D-DIC） is a widely used optical metrology in the experimental mechanics community because of its reliability, practicality, and flexibility. Although the precision of di...Three dimensional-digital image correlation （3D-DIC） is a widely used optical metrology in the experimental mechanics community because of its reliability, practicality, and flexibility. Although the precision of digital image correlation （DIC） has been thoroughly studied theoretically and numerically, verification experiments have seldom been performed, especially fbr complex surfaces with a small field of view （FOV）. In this work, the shape of a 1-yuan coin was measured using 3D-DIC; the shape was complex due to the presence of many fine details, and the FOV was relatively small because the coin diameter was only 25 mm. During the experiment, a novel strategy for speckle production was developed： white paint was simply sprayed onto the surface. Black paint was not used; instead, taking advantage of the reflective nature of the coin surface, polarized light and a Polaroid filter were introduced, and the polarization direction was carefully adjusted, ensuring that the spray pattern was extremely thin and that high-quality speckle images with significant contrast were captured. The three-dimensional coin shape was also successfully determined for comparison using a stylus profiler. The results demonstrate that 3D-DIC provides high precision in shape measurement even for complex surfaces with small FOV. The precision of 3D-DIC can reach 1/7000 of the field of view, corresponding to about 6 ~tm in this experiment.展开更多
In this paper,the occurrence and development mechanism of strain on the cross-section during the wood drying is explored.Therefore,strain regularity on the cross-section of 50 mm thickness elm(Ulmus rubra)board at the...In this paper,the occurrence and development mechanism of strain on the cross-section during the wood drying is explored.Therefore,strain regularity on the cross-section of 50 mm thickness elm(Ulmus rubra)board at the temperature of 40℃and 80℃is detected via digital image correlation technology.Hence,the difference between tangential and radial strain at surface and core layers was denoted.The results showed that strain distribution in the width direction of the board is uneven.Moreover,a large drying shrinkage strain occurs at the near-core layer,while the maximum strain difference reaches 4.08%.Hence,the surface of the board is cracked along the thickness direction.The radial strain of the board is higher than the tangential strain in the early stage of drying,while these strains are reversed in the later stage of drying.The temperature is related to the difference between the tangential and radial strains of the elm board.These differences at the core layer are larger than those of the surface layer.The conducted research results provide a theoretical basis for process optimization.展开更多
BACKGROUND Percutaneous sclerotherapy can be used to successfully treat venous malformations(VMs)of the head,neck,and limbs.However,the standard curative effect of sclerotherapy has rarely been analyzed,and there is c...BACKGROUND Percutaneous sclerotherapy can be used to successfully treat venous malformations(VMs)of the head,neck,and limbs.However,the standard curative effect of sclerotherapy has rarely been analyzed,and there is currently no accurate statistical method to measure the volume of VMs after sclerotherapy.Here,we propose a novel threedimensional(3D)reconstruction method to evaluate this effect.OBJECTIVE To test the feasibility of 3D software(MIMICS 19.0)to evaluate the treatment effect of sclerotherapy.METHODS This retrospective study included patients with VMs on the head,neck,and limbs who were treated with ethanol sclerotherapy or foam sclerotherapy every 8 weeks.MIMICS 19.0 was used to calculate the performance of the lesion after treatment and measure the VM volumes before and after the treatment.The effect of the clinical treatment dose on the lesion was evaluated,and the treatment effect of each patient was recorded.The relationship between the number of treatments and the reduced volume of VMs was analyzed.RESULTS Based on the MIMICS-calculated regions of interest(ROI),we found that 1 mL of ethanol reduced the lesion by 473 mm3 and that one dosage of foam(1 mL of polidocanol and 4 mL air content)reduced the lesion by 2138 mm3,demonstrating that the foam sclerosing agent exhibited greater efficacy in this study.CONCLUSIONS The MIMICS 3D volume reconstruction method can effectively and safely evaluate the efficacy of sclerotherapy and provide a preoperative evaluation.This method is simple,accurate,and feasible.展开更多
Stress measurement plays a crucial role in geomechanics and rock engineering,especially for the design and construction of large-scale rock projects.This paper presents a novel method,based on the traditional stress r...Stress measurement plays a crucial role in geomechanics and rock engineering,especially for the design and construction of large-scale rock projects.This paper presents a novel method,based on the traditional stress relief approach,for indirectly measuring rock stress using optical techniques.The proposed method allows for the acquisition of full-field strain evolution on the borehole’s inner wall before and after disturbance,facilitating the determination of three-dimensional(3D)stress information at multiple points within a single borehole.The study focuses on presenting the method’s theoretical framework,laboratory validation results,and equipment design conception.The theoretical framework comprises three key components:the optical imaging method of the borehole wall,the digital image correlation(DIC)method,and the stress calculation procedure.Laboratory validation tests investigate strain field distribution on the borehole wall under varying stress conditions,with stress results derived from DIC strain data.Remarkably,the optical method demonstrates better measurement accuracy during the unloading stage compared to conventional strain gauge methods.At relatively high stress levels,the optical method demonstrates a relative error of less than 7%and an absolute error within 0.5 MPa.Furthermore,a comparative analysis between the optical method and the conventional contact resistance strain gauge method highlights the optical method’s enhanced accuracy and stability,particularly during the unloading stage.The proposed optical stress measurement device represents a pioneering effort in the application of DIC technology to rock engineering,highlighting its potential to advance stress measurement techniques in the field.展开更多
基金the support of the National Natural Science Foundation of China(Grant Nos.42207199,52179113,42272333)Zhejiang Postdoctoral Scientific Research Project(Grant Nos.ZJ2022155,ZJ2022156)。
文摘Three-dimensional(3D)printing technology is increasingly used in experimental research of geotechnical engineering.Compared to other materials,3D layer-by-layer printing specimens are extremely similar to the inherent properties of natural layered rock masses.In this paper,soft-hard interbedded rock masses with different dip angles were prepared based on 3D printing(3DP)sand core technology.Uniaxial compression creep tests were conducted to investigate its anisotropic creep behavior based on digital imaging correlation(DIC)technology.The results show that the anisotropic creep behavior of the 3DP soft-hard interbedded rock mass is mainly affected by the dip angles of the weak interlayer when the stress is at low levels.As the stress level increases,the effect of creep stress on its creep anisotropy increases significantly,and the dip angle is no longer the main factor.The minimum value of the long-term strength and creep failure strength always appears in the weak interlayer within 30°–60°,which explains why the failure of the layered rock mass is controlled by the weak interlayer and generally emerges at 45°.The tests results are verified by comparing with theoretical and other published studies.The feasibility of the 3DP soft-hard interbedded rock mass provides broad prospects and application values for 3DP technology in future experimental research.
基金supported by the National Natural Science Foundation of China(Grant Nos.11332010,51271174,11372300,11127201,11472266&11428206)
文摘Three dimensional-digital image correlation （3D-DIC） is a widely used optical metrology in the experimental mechanics community because of its reliability, practicality, and flexibility. Although the precision of digital image correlation （DIC） has been thoroughly studied theoretically and numerically, verification experiments have seldom been performed, especially fbr complex surfaces with a small field of view （FOV）. In this work, the shape of a 1-yuan coin was measured using 3D-DIC; the shape was complex due to the presence of many fine details, and the FOV was relatively small because the coin diameter was only 25 mm. During the experiment, a novel strategy for speckle production was developed： white paint was simply sprayed onto the surface. Black paint was not used; instead, taking advantage of the reflective nature of the coin surface, polarized light and a Polaroid filter were introduced, and the polarization direction was carefully adjusted, ensuring that the spray pattern was extremely thin and that high-quality speckle images with significant contrast were captured. The three-dimensional coin shape was also successfully determined for comparison using a stylus profiler. The results demonstrate that 3D-DIC provides high precision in shape measurement even for complex surfaces with small FOV. The precision of 3D-DIC can reach 1/7000 of the field of view, corresponding to about 6 ~tm in this experiment.
基金supported by the National Natural Science Foundation of China(No.31901242)Heilongjiang Science Foundation Project(No.LH2020C038)National Undergraduate Training Programs for Innovations(No.202110225074)。
文摘In this paper,the occurrence and development mechanism of strain on the cross-section during the wood drying is explored.Therefore,strain regularity on the cross-section of 50 mm thickness elm(Ulmus rubra)board at the temperature of 40℃and 80℃is detected via digital image correlation technology.Hence,the difference between tangential and radial strain at surface and core layers was denoted.The results showed that strain distribution in the width direction of the board is uneven.Moreover,a large drying shrinkage strain occurs at the near-core layer,while the maximum strain difference reaches 4.08%.Hence,the surface of the board is cracked along the thickness direction.The radial strain of the board is higher than the tangential strain in the early stage of drying,while these strains are reversed in the later stage of drying.The temperature is related to the difference between the tangential and radial strains of the elm board.These differences at the core layer are larger than those of the surface layer.The conducted research results provide a theoretical basis for process optimization.
文摘BACKGROUND Percutaneous sclerotherapy can be used to successfully treat venous malformations(VMs)of the head,neck,and limbs.However,the standard curative effect of sclerotherapy has rarely been analyzed,and there is currently no accurate statistical method to measure the volume of VMs after sclerotherapy.Here,we propose a novel threedimensional(3D)reconstruction method to evaluate this effect.OBJECTIVE To test the feasibility of 3D software(MIMICS 19.0)to evaluate the treatment effect of sclerotherapy.METHODS This retrospective study included patients with VMs on the head,neck,and limbs who were treated with ethanol sclerotherapy or foam sclerotherapy every 8 weeks.MIMICS 19.0 was used to calculate the performance of the lesion after treatment and measure the VM volumes before and after the treatment.The effect of the clinical treatment dose on the lesion was evaluated,and the treatment effect of each patient was recorded.The relationship between the number of treatments and the reduced volume of VMs was analyzed.RESULTS Based on the MIMICS-calculated regions of interest(ROI),we found that 1 mL of ethanol reduced the lesion by 473 mm3 and that one dosage of foam(1 mL of polidocanol and 4 mL air content)reduced the lesion by 2138 mm3,demonstrating that the foam sclerosing agent exhibited greater efficacy in this study.CONCLUSIONS The MIMICS 3D volume reconstruction method can effectively and safely evaluate the efficacy of sclerotherapy and provide a preoperative evaluation.This method is simple,accurate,and feasible.
基金funding support from the National Natural Science Foundation of China(Grant Nos.52125903 and 52209149).
文摘Stress measurement plays a crucial role in geomechanics and rock engineering,especially for the design and construction of large-scale rock projects.This paper presents a novel method,based on the traditional stress relief approach,for indirectly measuring rock stress using optical techniques.The proposed method allows for the acquisition of full-field strain evolution on the borehole’s inner wall before and after disturbance,facilitating the determination of three-dimensional(3D)stress information at multiple points within a single borehole.The study focuses on presenting the method’s theoretical framework,laboratory validation results,and equipment design conception.The theoretical framework comprises three key components:the optical imaging method of the borehole wall,the digital image correlation(DIC)method,and the stress calculation procedure.Laboratory validation tests investigate strain field distribution on the borehole wall under varying stress conditions,with stress results derived from DIC strain data.Remarkably,the optical method demonstrates better measurement accuracy during the unloading stage compared to conventional strain gauge methods.At relatively high stress levels,the optical method demonstrates a relative error of less than 7%and an absolute error within 0.5 MPa.Furthermore,a comparative analysis between the optical method and the conventional contact resistance strain gauge method highlights the optical method’s enhanced accuracy and stability,particularly during the unloading stage.The proposed optical stress measurement device represents a pioneering effort in the application of DIC technology to rock engineering,highlighting its potential to advance stress measurement techniques in the field.
