Numerical simulation of flow field deposition and erosion characteristics around bridge-road transition section

Wind-sand flow generates erosion and deposition around obstacles such as bridges and roadbeds, resulting in sand damage and endangering railway systems in sandy regions. Previous studies have mainly focused on the flow field around roadbeds, overlooking detailed examinations of sand particle erosion and deposition patterns near bridges and roadbeds. This study employs numerical simulations to analyze the influence of varying heights and wind speeds on sand deposition and erosion characteristics at different locations: the bridge-road transition section(side piers), middle piers, and roadbeds. The results show that the side piers, experience greater accumulation than the middle piers. Similarly, the leeward side of the roadbed witnesses more deposition compared to the windward side. Another finding reveals a reduced sand deposition length as the vertical profile, in alignment with the wind direction, moves further from the bridge abutments at the same clearance height. As wind speeds rise, there’s a decline in sand deposition and a marked increase in erosion around the side piers, middle piers and roadbeds. In conclusion, a bridge clearance that’s too low can cause intense sand damage near the side piers, while an extremely high roadbed may lead to extensive surface sand deposition. Hence, railway bridges in areas prone to sandy winds should strike a balance in clearance height. This research provides valuable guidelines for determining the most suitable bridge and roadbed heights in regions affected by wind and sand.

Flow field, sedimentation, and erosion characteristics around folded linear HDPE sheet sand fence: Numerical simulation study

Wind and sand hazards are serious in the Milan Gobi area of the Xinjiang section of the Korla Railway. In order to ensure the safe operation of railroads, there is a need for wind and sand protection in heavily sandy areas. The wind and sand flow in the region is notably bi-directional. To shield railroads from sand, a unique sand fence made of folded linear high-density polyethylene(HDPE) is used, aligning with the principle that the dominant wind direction is perpendicular to the fence. This study employed field observations and numerical simulations to investigate the effectiveness of these HDPE sand fences in altering flow field distribution and offering protection. It also explored how these fences affect the deposition and erosion of sand particles. Findings revealed a significant reduction in wind speed near the fence corner;the minimum horizontal wind speed on the leeward side of the first sand fence(LSF) decreased dramatically from 3 m/s to 0.64 m/s. The vortex area on the LSF markedly impacted horizontal wind speeds. Within the LSF, sand deposition was a primary occurrence. As wind speeds increased, the deposition zone shrank, whereas the positive erosion zone expanded. Close to the folded corners of the HDPE sand fence, there was a notable shift from the positive erosion zone to a deposition zone. Field tests and numerical simulations confirmed the high windproof efficiency(WE) and sand resistance efficiency(SE) in the HDPE sand fence. Folded linear HDPE sheet sand fence can effectively slow down the incoming flow and reduce the sand content, thus achieving good wind and sand protection. This study provides essential theoretical guidance for the design and improvement of wind and sand protection systems in railroad engineering.

Bulking factor of the strata overlying the gob and a three-dimensional numerical simulation of the air leakage flow field

现在的学习检验与在家和国外执行的嘴 bulking 因素有关的研究的结果。一个三维的嘴 bulking 因素的数学功能基于一个三维的嘴模型被描述。为空隙和渗透比率拿价值的方法也被建议。充分使机械化的最高的煤的空气漏的法律在这研究被研究。结果证明上面、更低的 crossheadings 附近的空气流动的速度在在从工作的脸的一样的距离的嘴的中央节比那高。当在工作的脸的空气的数量超过批评数量时，在上面、更低的 crossheadings 的自燃地区的宽度在中央节也比那大。处于这种状况，钥匙正在阻止从 self-igniting 在上面、更低的 crossheadings 离开的煤。在工作的脸减少空气的数量能减少自燃地区的宽度，特别上面、更低的 crossheadings 附近的宽度。这也在工作的脸的方向移动自燃地区。它能由在惰性的 crossheadings 使煤左并且由有效地在工作的脸控制空气的数量在嘴阻止煤 self-igniting。

Numerical simulation study on multiphase flow pattern of hydrate slurry

The research on the multiphase flow characteristics of hydrate slurry is the key to implementing the risk prevention and control technology of hydrate slurry in deep-water oil and gas mixed transportation system.This paper established a geometric model based on the high-pressure hydrate slurry experimental loop.The model was used to carry out simulation research on the flow characteristics of gas-liquid-solid three-phase flow.The specific research is as follows:Firstly,the effects of factors such as slurry flow velocity,hydrate particle density,hydrate particle size,and hydrate volume fraction on the stratified smooth flow were specifically studied.Orthogonal test obtained particle size has the most influence on the particle concentration distribution.The slurry flow velocity is gradually increased based on stratified smooth flow.Various flow patterns were observed and their characteristics were analyzed.Secondly,increasing the slurry velocity to 2 m/s could achieve the slurry flow pattern of partial hydrate in the pipeline transition from stratified smooth flow to wavy flow.When the flow rate increases to 3 m/s,a violent wave forms throughout the entire loop.Based on wave flow,as the velocity increased to 4 m/s,and the flow pattern changed to slug flow.When the particle concentration was below 10%,the increase of the concentration would aggravate the slug flow trend;if the particle concentration was above 10%,the increase of the concentration would weaken the slug flow trend,the increase of particle density and liquid viscosity would weaken the tendency of slug flow.The relationship between the pressure drop gradients of several different flow patterns is:slug flow>wave flow>stratified smooth flow.

Research on numerical simulation of flow field in shallow-bath dense-medium separator

介绍了浅槽重介分选机的结构、工作原理和技术特点，并采用Fluent软件，对浅槽重介分选机内部的流场进行了分析和研究，得出了各主要位置的速度和速度变化规律。揭示了浅槽重介分选机在分选过程中的悬浮液体流场形态及运动规律，以为其结构设计和改进提供理论依据。

Numerical Simulation of High Speed Rotating Waterjet Flow Field in a Semi Enclosed Vacuum Chamber

In this paper,a three dimension model is built according to real surface cleaner in airport runway rubber mark cleaning vehicle and numerical simulation of this model is carried out using Ansys Fluent software.After comparison and analysis of the flow fields between high speed rotating waterjet and static waterjet formerly studied by other researchers,the influences of different standoff distances from nozzle outlet to runway surface and rotation speeds on rubber mark cleaning effect are simulated and analyzed.Results show the optimal operation parameters for the simulated model and quantitative advices are given for design,manufacture and operation of the airport runway rubber mark cleaning vehicle.

Numerical Simulation of Coupled Molten Steel Flow and Temperature Fields in Compact Strip Production Casting

Based on the casting manufacture practice of steel slabs by CSP technology, the flow and the temperature fields of the funnel mould and the secondary cooling segment were simulated using the commercial code, CFX4. Compared with other physical investigations, the correlative data of the present simulation results are in good agreement with them. Therefore, a more comprehensive survey for metallurgy characteristic of the flow and the temperature fields in CSP continuous casting process can be achieved.

The mesoscale numerical simulation of the flow field of the Hainan Island and the Leizhou Peninsula

The flow field over Hainan Island and the Leizhou Peninsula in summer and winter is discussed with three-dimensional mesoscale model developed in the University of Virginia and using the representative meteorological data of January and July.Simulation results indicate that the local weather characteristics over the Hainan Island are distinctly influenced by theWuzhi Mountain terrain. The cloudy or rainfall weather over the northeast of the Wuzhi Mountain occurs easily, under proper large-scale conditions of flow, temperature and humidity. while west wind prevails. The overcast or rainfall weather is often induced by strong convection in the afternoon over west of the Hainan Island under easterly prevailing wind.

Numerical Simulation of the Air Jet Flow Field in the Melt Blowing Process

The theoretical model of the flow field of the dual slot die in melt blowing process is founded. The model is solved numerically with finite difference method. The distributions of the air velocity component in x direction along x-axis and y-axis and the air temperature distributions along x-axis and y-axis are obtained via numerical computation. The computation results coincide with the experimental data given by Harpham and Shambaugh. The distributions of the air velocity and air temperature are introduced into the air drag model of melt blowing. The model prediction of the fiber diameter agrees with the experimental data well.

NUMERICAL SIMULATION ANALYSIS OF EXTERNAL FLOW FIELD OF WAGON-SHAPED CAR AT THE MOMENT OF PASSING

In the course of studying on aerodynamic change and its effect on steering stability and controllability of an automobile in passing, because of multi interaction streams, it is difficult to use traditional methods, such as wind tunnel test and road test. If the passing process of an automobile is divided into many time segments, so as to avoid the use of moving mesh which takes large calculation resource and CPU processing time in calculating, the segments are simulated with computational fluid dynamics （CFD） method, then the approximate computational results about external flow field will be obtained. On the basis of the idea, the change of external flow field of wagon-shaped car at the moment of passing is simulated through solving three-dimensional, steady and uncompressible N-S equations with finite volume method. Numerical simulation analysis of side force coefficient, stream lines, body surface pressure distribution of wagon-shaped car are presented and a preliminary discussion of aerodynamic characteristics of correlative situations is obtained. Finally, the C3 -x/l curve of side force coefficient（C3） of car following relative distance （x/l） between cars is obtained. By comparison, the curve is coincident well with the experimental data, which shows creditability of numerical simulation methods presented.

Numerical simulation of electro-magnetic and flow fields of TiAl melt under electric field

This article aims at building an electromagnetic and fluid model, based on the Maxwell equations and Navier-Stokes equations, in TiAl melt under two electric fields.FEM (Finite Element Method) and APDL (ANSYS Parametric Design Language) were employed to perform the simulation, model setup, loading and problem solving.The melt in molds of same cross section area with different flakiness ratio (i.e.width/depth) under the load of sinusoidal current or pulse current was analyzed to obtain the distribution of electromagnetic field and flow field.The results show that the induced magnetic field occupies sufficiently the domain of the melt in the mold with a flakiness ratio of 5:1.The melt is driven bipolarly from the center in each electric field.It is also found that the pulse electric field actuates the TiAl melt to flow stronger than what the sinusoidal electric field does.

Mathematical Modeling,Field Calibration and Numerical Simulation of Low-Speed Mixed Traffic Flow in Cities

Ｗｉｔｈｔｈｅｒａｐｉｄｄｅｖｅｌｏｐｍｅｎｔｏｆｔｒａｎｓｐｏｒｔａｔｉｏｎａｎｄａｕｔｏｍｏｂｉｌｅｉｎｄｕｓｔｒｙ，ｔｈｅｃｏｎｆｌｉｃｔｂｅｔｗｅｅｎｍｏｔｏｒｍａｎｕｆａｃｔｕｒｅａｎｄｈｉｇｈｗａｙｃｏｎｓｔｒｕｃｔｉｏｎｂｅｃｏｍｅｓｓ...

INFLUENCE OF EXTERNAL MAGNETIC FIELD ON THE FLOW FIELD IN MOLTEN SEMICONDUCTOR OF CZOCHRALSKI CRYSTAL GROWTH——A NUMERICAL SIMULATION

Numerical results show that an external magnetic field may influence significantly the flow pattern in the molten semiconductor of Czochralski crystal growth. The melt flow could be pronouncedly damped by a magnet. ic field with the intensity of several thousands Gauss, while the temperature field is affected only in a less extent by the magnetic field.

Numerical simulation on turbulent flow field in convergentdiveroent nozzle

Because of the complication of turbulence's mechanism and law as well as thejet pressure in nozzle is difficult to test by experiment, five turbulent models were appliedto numerically simulate the turbulent flow field in convergent-divergent nozzle. Theoryanalysis and experiment results of mass flow rates conclude that the RNG к-з model is themost suitable model. The pressure distribution in the convergent-divergent nozzle was revealed by computational fluid dynamic (CFD) simulating on the turbulent flow field underdifferent pressure conditions. The growing conditions of cavitation bubbles were shown;meanwhile, the phenomena in the experiment could be explained. The differential pressure between the upstream and downstream in nozzle throat section can improve thecavitating effect of cavitation water jet.

NUMERICAL SIMULATION OF THE FLOW FIELD IN A THERMAL PLASMA REACTOR

A numerical simulation is presented for a thermal plasma reactor with particle-trajectory model in this paper. Turbulance is considered by using simple SGS model. The governing equations are solved by means of the algorithm of SIMPLER. The calculated results give the velocity and the temperature fields within plasma reactor, and the trajectories of the injected particles.

Numerical Simulation of Tripolar Vortex in Dusty Plasma with Sheared Flow and Sheared Magnetic Field

This article presents a study we have made of one class of coherent structures of the tripolar vortex. Considering the sheared flow and sheared magnetic field which are common in the thermonuclear plasma and space plasma, we have simulated the dynamics of the tripolar vortex. The results show that the tripolar vortex is largely stable in most cases, but a strongly sheared magnetic field will make the structure less stable, and lead it to decays into single vortices with the large space scale. These results are consistent with findings from former research about the dipolar vortex.

Study on optimal design of vertical-shaft mechanical mixer based on numerical simulation of flow field

In the paper the three-dimensional flow fields are numerically simulated in the vertical-shaft mechanical mix tank of a water treatment plant by means of FLUENT software based on the method of Computational Fluid Dynamics (CFD). The influences of design parameters on flow fields and the mixing effect are analyzed. Firstly,the prediction capability of the turbulence model adopted in simulations is evaluated. And then,the mesh independence is checked up. Finally,the flow fields in various dimensionless blade diameters and dimensionless shaft spans are numerically simulated respectively. The results have shown that the numerical simulation method based on CFD is a feasible assistance for the optimal designs of mixers. Moreover,the optimal design of the blade diameter should take into account both the flow field and the power consumption. The optimization of the shaft span is to achieve a relatively even distribution of the flow field without any rupture. With the consideration of an optimal design,the dimensionless blade diameter and dimensionless shaft span should be 0.45 and 0.57 respectively in the case.

Numerical simulation of the dynamic characteristics of flow fields under ice

Atmospheric and oceanic drag are the main environmental forces controlling sea ice drift. Oceanic drag includes the form drag generated by water pressure gradients on the side of ice floes or on ice ridges, and the skin friction generated by viscous flow on the bottom of ice floes. In this study, we carried out a two-dimensional numerical simulation using FLUENT software to investigate the characteristics of dynamic flow under ice with a smooth undersurface. We studied water drag and flow field distribution below the ice under different conditions of ice draft and flow velocity, and the results agreed well with data from laboratory-based physical modeling tests, demonstrating the ability of the numerical model to reproduce the dynamic interactions between sea ice and the flow field. The degree of distortion in the flow field caused by ice increased as the ice draft increased. Vortexes occurred in the wake field of the floe, and the centers of the vortexes moved away from the ice with increasing ice draft. The simulated drag of water on ice showed a clear linear relationship with the square of the flow velocity.

Numerical simulation on flow field,wind erosion and sand sedimentation patterns over railway subgrades

The railway subgrades in the sandy areas act as an obstacle interfering wind-blown sand,causing sand erosion and sedimentation,which can disrupt the safe and stable operation of the railway system.Most previous studies mainly focus on the flow field around railway subgrades,however,the real erosion and sedimentation patterns are rarely studied.This study aims to analyze the erosion and sand sedimentation patterns of wind-blown sand over the subgrades with different heights and steel rails using the ratio of the wall shear stress to the critical value of erosion shear stress.Results show that wind erosion near the top of the upwind slope of the embankment and the shoulder on the upwind side are more severe,and the severity increases with an increase in the height of the embankment.With the increase of wind velocity,sand sedimentation both on the windward and leeside of the subgrade decreases and wind erosion by reverse flow occur.This study indicates that railways in sandy areas should be constructed with a moderate subgrade height(4 m).

Research on Numerical Simulation for Flow Field in a Jigger

Jigger is the main equipment in coal processing industry in China, which is developed towards large-scale device. By using the homemade device LTX-35 jigger as a model employing mesh division with non-orthogonal mesh for different kinds of through-flow passage, and completing the numerical simulation with the computational fluid dynamics (CDF) software-PHOENICS, the velocity distribution in different flow fields resulting from guide plates of varied structures are obtained. The results from the simulation show that 1 ) the degree of velocity uniformity of the flow field can be improved if a flat guide plate is replaced by a curved one in the jigger; 2) the best result can be achieved by using a semicircular guide plate.