Development of a toroidal soft x-ray imaging system and application for investigating three-dimensional plasma on J-TEXT

A toroidal soft x-ray imaging(T-SXRI)system has been developed to investigate threedimensional(3D)plasma physics on J-TEXT.This T-SXRI system consists of three sets of SXR arrays.Two sets are newly developed and located on the vacuum chamber wall at toroidal positionsφof 126.4°and 272.6°,respectively,while one set was established previously atφ=65.50.Each set of SXR arrays consists of three arrays viewing the plasma poloidally,and hence can be used separately to obtain SXR images via the tomographic method.The sawtooth precursor oscillations are measured by T-SXRI,and the corresponding images of perturbative SXR signals are successfully reconstructed at these three toroidal positions,hence providing measurement of the 3D structure of precursor oscillations.The observed 3D structure is consistent with the helical structure of the m/n=1/1 mode.The experimental observation confirms that the T-SXRI system is able to observe 3D structures in the J-TEXT plasma.

Multi-objective strategy to optimize dithering technique for high-quality three-dimensional shape measurement

Dithering optimization techniques can be divided into the phase-optimized technique and the intensity-optimized technique. The problem with the former is the poor sensitivity to various defocusing amounts, and the problem with the latter is that it cannot enhance phase quality directly nor efficiently. In this paper, we present a multi-objective optimization framework for three-dimensional(3D) measurement by utilizing binary defocusing technique. Moreover, a binary patch optimization technique is used to solve the time-consuming issue of genetic algorithm. It is demonstrated that the presented technique consistently obtains significant phase performance improvement under various defocusing amounts.

Evaluating the contribution of satellite measurements to the reconstruction of three-dimensional ocean temperature fields in combination with Argo profiles

Assimilation systems absorb both satellite measurements and Argo observations.This assimilation is essential to diagnose and evaluate the contribution from each type of data to the reconstructed analysis,allowing for better configuration of assimilation parameters.To achieve this,two comparative reconstruction schemes were designed under the optimal interpolation framework.Using a static scheme,an in situ-only field of ocean temperature was derived by correcting climatology with only Argo profiles.Through a dynamic scheme,a synthetic field was first derived from only satellite sea surface height and sea surface temperature measurements through vertical projection,and then a combined field was reconstructed by correcting the synthetic field with in situ profiles.For both schemes,a diagnostic iterative method was performed to optimize the background and observation error covariance statics.The root mean square difference(RMSD)of the in situ-only field,synthetic field and combined field were analyzed toward assimilated observations and independent observations,respectively.The rationale behind the distribution of RMSD was discussed using the following diagnostics:(1)The synthetic field has a smaller RMSD within the global mixed layer and extratropical deep waters,as in the Northwest Pacific Ocean;this is controlled by the explained variance of the vertical surface-underwater regression that reflects the ocean upper mixing and interior baroclinicity.(2)The in situ-only field has a smaller RMSD in the tropical upper layer and at midlatitudes;this is determined by the actual noise-to-signal ratio of ocean temperature.(3)The satellite observations make a more significant contribution to the analysis toward independent observations in the extratropics;this is determined by both the geographical feature of the synthetic field RMSD(smaller at depth in the extratropics)and that of the covariance correlation scales(smaller in the extratropics).

A method for phase reconstruction in optical three-dimensional shape measurement

In optical three-dimensional shape measurement, a method of improving the measurement precision for phase reconstruction without phase unwrapping is analyzed in detail. Intensities of any five consecutive pixels that lie in the x-axis direction of the phase domain are given. Partial derivatives of the phase function in the x- and y-axis directions are obtained with a phase-shifting mechanism, the origin of which is analysed. Furthermore, to avoid phase unwrapping in the phase reconstruction, we derive the gradient of the phase function and perform a two-dimensional integral along the x- and y-axis directions. The reconstructed phase can be obtained directly by performing numerical integration, and thus it is of great convenience for phase reconstruction. Finally, the results of numerical simulations and practical experiments verify the correctness of the proposed method.

A fast and precise three-dimensional measurement system based on multiple parallel line lasers

This paper conducts a trade-off between efficiency and accuracy of three-dimensional(3 D)shape measurement based on the triangulation principle,and introduces a flying and precise 3 D shape measurement method based on multiple parallel line lasers.Firstly,we establish the measurement model of the multiple parallel line lasers system,and introduce the concept that multiple base planes can help to deduce the unified formula of the measurement system and are used in simplifying the process of the calibration.Then,the constraint of the line spatial frequency,which maximizes the measurement efficiency while ensuring accuracy,is determined according to the height distribution of the object.Secondly,the simulation analyzing the variation of the systemic resolution quantitatively under the circumstance of a set of specific parameters is performed,which provides a fundamental thesis for option of the four system parameters.Thirdly,for the application of the precision measurement in the industrial field,additional profiles are acquired to improve the lateral resolution by applying a motor to scan the 3 D surface.Finally,compared with the line laser,the experimental study shows that the present method of obtaining 41220 points per frame improves the measurement efficiency.Furthermore,the accuracy and the process of the calibration are advanced in comparison with the existing multiple-line laser and the structured light makes an accuracy better than 0.22 mm at a distance of 956.02 mm.

Three-Dimensional Velocity Distribution Measurement Using Ultrasonic Velocity Profiler with Developed Transducer

This study describes an ultrasonic velocity profiler that uses a new ultrasonic array transducer with unique 5-element configuration, with all five elements acting as transmitters and four elements as receivers. The receivers are designed to reduce the amount of uncertainty. As the fluid moves through this setup, four Doppler frequencies are obtained. The multi-dimensional velocity information along the measurement line can be reconstructed. The transducer has a compact geometry suitable for a wide range of applications, including narrow flow areas. The transducer’s basic frequency and sound pressure are selected and evaluated to be compatible with the application. First, to confirm the measurement ability, the measurement of the developed system in two-dimensional flow is validated by comparing it to the theoretical data. The uncertainty of measurement was within 15%. Second, the three-dimensional measurement in turbulent and swirling flow is proved experimentally to check the applicability of the proposed technique.

Digital measurement of bone tumor volume by CT three-dimensional reconstruction technology

Objective To discuss the measurement of bone tumor volume on the basis of three dimensional images segmentation technology. Methods Twenty patients with lacunar bone tumor from Tianjin Hospital and Tongji Hospital were included in the

Three-Dimensional Analytical Modeling of Axial-Flux Permanent Magnet Drivers

In this paper, the axial-flux permanent magnet driver is modeledand analyzed in a simple and novel way under three-dimensional cylindricalcoordinates. The inherent three-dimensional characteristics of the deviceare comprehensively considered, and the governing equations are solved bysimplifying the boundary conditions. The axial magnetization of the sectorshapedpermanent magnets is accurately described in an algebraic form bythe parameters, which makes the physical meaning more explicit than thepurely mathematical expression in general series forms. The parameters of theBessel function are determined simply and the magnetic field distribution ofpermanent magnets and the air-gap is solved. Furthermore, the field solutionsare completely analytical, which provides convenience and satisfactoryaccuracy for modeling a series of electromagnetic performance parameters,such as the axial electromagnetic force density, axial electromagnetic force,and electromagnetic torque. The correctness and accuracy of the analyticalmodels are fully verified by three-dimensional finite element simulations and a15 kW prototype and the results of calculations, simulations, and experimentsunder three methods are highly consistent. The influence of several designparameters on magnetic field distribution and performance is studied and discussed.The results indicate that the modeling method proposed in this papercan calculate the magnetic field distribution and performance accurately andrapidly, which affords an important reference for the design and optimizationof axial-flux permanent magnet drivers.

Diameters and form of skull base foramen ovale measured by three-dimensional spiral CT thin-slice scan in healthy adults

BACKGROUND： The accurate measurements of various data of the bone diameters of foramen ovale of living person can change the methods of puncturing trigeminal gasserian ganglion via foramen ovale for treating trifacial neuralgia from the experience of puncture operator only to puncture by taking the objective data of measurement as the evidence, which is good for improving the accuracy of puncturing trigeminal ganglion and reducing side effects. OBJECTIVE ： To observe the forms of foramen ovales in healthy adults displayed by volume rendering and multi-planar reconstruction after three-dimensional spiral CT thin-slice scan of skull base, and measure the longitudinal diameter and transverse diameter. DESIGN ： A repetitive observation and measurement SETTINGS ： Department of Neurosurgery and Department of Medical Imaging, Foshan Hospital of Traditional Chinese Medicine. PARTICIPANTS： Fifty healthy adults （100 sides）, who were examined with three-dimensional spiral CT scan, were randomly selected from the Department of Medical Imaging, Foshan Hospital of Traditional Chinese Medicine from January 2005 to January 2006, including 26 males and 24 females, aged 25-68 years with an average of 48 years old. They were all informed and agreed with the examination. METHODS ： The subjects were examined with the Philips 16-slice spiral CT-Mx 8000 IDT CT apparatus （Philips Company, Holland）, the scanning ranged from 2 cm below the canthomeatal line to the level of suprasellar cistem. The width of collimator was 0.75 mm, pitch was 0.663; tube current was 350 mA, voltage was 120 kV, resolution was 512×512 matrix; slice thickness of reconstruction was 1 mm, and interval was 0.5 mm. After the three-dimensional spiral CT thin-slice scan of skull base, the image post-processing techniques including volume rendering and multi-planar reconstruction were applied to observe the forms of foramen ovales, and measure the size, longitudinal diameter and transverse diameter of the foramen ovales. The figures of the foramen ovales were drawn with mouse along the boundary of bone porous margin and soft tissue. According to the indications, the diameters were measured with computer to observe the forms of foramen ovales. MAIN OUTCOME MEASURES ： The longitudinal diameter, transverse diameter and form of foramen ovales were observed. RESULTS： All the 50 healthy adults （100 sides） were involved in the analysis of results. （1） It was observed in the volume rendering images that foramen ovales had four forms of oval shape （77 sides）, kidney shape （12 sides）, round shape （7 sides）, ribbon shape （4 sides）. （2） The longitudinal diameters of left and right foramen ovales were （7.67±1.32） and （7.98±1.45） mm, and the transverse diameters were （4.04±0.83）, （4.09±1.07） mm; There was no obvious difference between left and right longitudinal diameters （t = 1.63, P = 0.11 ）, and left and right transverse diameters were close （t = 0.45, P= 0.65）. CONCLUSION ： The non-invasive techniques of volume rendering and multi-planar reconstruction after three-dimensional spiral CT thin-slice scan can clearly display the formand size of foramen ovale in healthy adults.

Development of an In-Situ Laser Machining System Using a Three-Dimensional Galvanometer Scanner

In this study, a three-dimensional (3D) in-situ laser machining system integrating laser measurement and machining was built using a 3D galvanometer scanner equipped with a side-axis industrial camera. A line structured light measurement model based on a galvanometer scanner was proposed to obtain the 3D information of the workpiece. A height calibration method was proposed to further ensure measurement accuracy, so as to achieve accurate laser focusing. In-situ machining software was developed to realize time-saving and labor-saving 3D laser processing. The feasibility and practicability of this in-situ laser machining system were verified using specific cases. In comparison with the conventional line structured light measurement method, the proposed methods do not require light plane calibration, and do not need additional motion axes for 3D reconstruction;thus they provide technical and cost advantages. The insitu laser machining system realizes a simple operation process by integrating measurement and machining,which greatly reduces labor and time costs.

A comparison of summer precipitation structures over the South China Sea and the East China Sea based on tropical rainfall measurement mission

The three-dimensional structures of summer precipitation over the South China Sea （SCS） and the East China Sea （ECS） are investigated based on tropical rainfall measurement mission （TRMM）. The primary results are as follows. First, both the convective and stratiform precipitation rates in the SCS are much higher than those of the ECS. The contribution of the convective cloud precipitation to the surface precipitation is primarily over the SCS and the ECS with a proportion of about 70%, but the contribution of convective cloud precipitation is slightly larger in the SCS than the ECS. The contribution of stratus precipitation is slightly larger in the ECS than that in the SCS. Second, the content of cloud particles and precipitation particles in the ECS in June was greater than that in the SCS, while in July and August, the content of cloud and precipitation particles in the ECS was less than that in the SCS. Third, the latent heat profile of the ECS is quite different from that of the SCS. In June, the peak values of evaporation and condensation latent heating rates in the ECS are greater than those in the SCS. In July and August, however, the peak values of evaporation and condensation latent heating rates in the ECS are about 0.05°/h less than those in the SCS.

EXPERIMENTAL INVESTIGATION FOR THE EFFECT OF ROTATION ON THREE-DIMENSIONAL FLOW FIELD IN FILM-COOLED TURBINE

An experimental investigation of three-dimensional flow field in a film-cooled turbine model is carried out by using particle image velocimeter （PIV） in a low-speed wind tunnel. The effects of different blowing ratios （M=1.5, 2） on the flow field are studied. The experimental results reveal the classical phenomena of the formation of kidney vortex pair and secondary flow in wake region behind the jet hole. And the changes of the kidney vortex pair and the wake at different locations away from the hole on the suction and pressure sides are also studied. Compared with the flow field in stationary cascade, there are centrifugal force and Coriolis force existing in the flow field of rotating turbine, and these forces bring the radial velocity in the jet flow. The effect of rotatien on the flow field of the pressure side is more distinct than that on the suction side from the measured flow fields in Y-Z plane and radial velocity contours. The increase of blowing ratio makes the kidney vortex pair and the secondary flow in the wake region stronger and makes the range of the wake region enlarged.

Three-Dimensional Thermo-Elastic-Plastic Finite Element Method Modeling for Predicting Weld-Induced Residual Stresses and Distortions in Steel Stiffened-Plate Structures

The objective of the present paper is to develop nonlinear finite element method models for predicting the weld-induced initial deflection and residual stress of plating in steel stiffened-plate structures. For this purpose, three-dimensional thermo-elastic-plastic finite element method computations are performed with varying plate thickness and weld bead length (leg length) in welded plate panels, the latter being associated with weld heat input. The finite element models are verified by a comparison with experimental database which was obtained by the authors in separate studies with full scale measurements. It is concluded that the nonlinear finite element method models developed in the present paper are very accurate in terms of predicting the weld-induced initial imperfections of steel stiffened plate structures. Details of the numerical computations together with test database are documented.

Multi-Schlieren CT Measurements of Supersonic Microjets from Circular and Square Micro Nozzles

Instantaneous three-dimensional (3D) density distributions of a shock-cell structure of perfectly and imperfectly expanded supersonic microjets escaping into an ambient space are measured. For the 3D observation of supersonic microjets, non-scanning 3D computerized tomography (CT) technique using a 20-directional quantitative schlieren optical system with flashlight source is employed for simultaneous schlieren photography. The 3D density distributions data of the microjets are obtained by 3D-CT reconstruction of the projection’s images using maximum likelihood-expectation maximization. Axisymmetric convergent-divergent (Laval) circular and square micro nozzles with operating nozzle pressure ratio 5.0, 4.5, 4.0, 3.67, and 3.5 have been studied. This study examines perfectly expanded, overexpanded, and underexpanded supersonic microjets issued from micro nozzles with fully expanded jet Mach numbers Mj ranging from 1.47 - 1.71, where the design Mach number is Md = 1.5. A complex phenomenon for free square microjets called axis switching is clearly observed with two types “upright” and “diagonal” of “cross-shaped”. The initial axis-switching is 45° within the first shock-cell range. In addition, from the symmetry and diagonal views of square microjets for the first shock-cells, two different patterns of shock waves are viewed. The shock-cell spacing and supersonic core length for all nozzle pressure ratios are investigated and reported.

宁晋超深盐穴储气库盐系地层地应力测定分析

地应力是盐穴储气库钻完井设计、运行压力设计等方面的重要基础数据,同时在储气库安全运行、经营管理等方面具有非常重要的意义。宁晋石盐田盐岩平均埋深超过2700 m,而国际上基于超深盐岩地应力的研究鲜有报道,这使宁晋盐穴储气库造腔层段地应力的测定面临很大的技术挑战。文章主要以水压致裂法(HF)和声发射试验(AE)两种测试方法为主,对比已有的区域构造应力测试结果,基于Z1资料井对研究区盐系地层地应力分布特征进行综合分析,研究表明:(1)Z1井盐系地层水平最大主应力方向总体表现为近东西向;(2)Z1井盐系地层地应力整体上随深度增大,水平最大主应力为51.9~60.0 MPa,水平最小主应力为43.2~53.7 MPa,垂向最大应力为65.7 MPa;(3)Z1井盐系地层地应结构总体表现为S_(V)>S_(H)>S_(h),垂向应力为最大主应力,区域应力状态属于正断层应力环境。

高地应力隧道岩爆施工风险评估及管控措施

依托某隧道项目,通过收集项目的设计文件、地勘报告,分析项目的地应力背景、岩体的物理力学特性、对岩爆进行了预测与综合评价。并建立了高地应力隧道岩爆施工风险评估指标体系,提出了相应的控制措施。

Precise 3D shape measurement of three-dimensional digital image correlation for complex surfaces

Three dimensional-digital image correlation(3 D-DIC) is a widely used optical metrology in the experimental mechanics community because of its reliability, practicality, and flexibility. Although the precision of digital image correlation(DIC) has been thoroughly studied theoretically and numerically, verification experiments have seldom been performed, especially for complex surfaces with a small field of view(FOV). In this work, the shape of a 1-yuan coin was measured using 3 D-DIC; the shape was complex due to the presence of many fine details, and the FOV was relatively small because the coin diameter was only 25 mm. During the experiment, a novel strategy for speckle production was developed: white paint was simply sprayed onto the surface. Black paint was not used; instead, taking advantage of the reflective nature of the coin surface, polarized light and a Polaroid filter were introduced, and the polarization direction was carefully adjusted, ensuring that the spray pattern was extremely thin and that high-quality speckle images with significant contrast were captured. The three-dimensional coin shape was also successfully determined for comparison using a stylus profiler. The results demonstrate that 3 D-DIC provides high precision in shape measurement even for complex surfaces with small FOV. The precision of 3 D-DIC can reach 1/7000 of the field of view, corresponding to about 6 μm in this experiment.

A modified moire interferometer for three-dimensional displacement measurement

This paper presents a new optical interferometric system, MMI-T/G, composed of a modified four-beam moire interferometer and a Twyman/Green interferometer. The MMI-T/G system can measure three-dimensional displacement fringe patterns with a single loading on the specimen, and the in-plane and out-of-plane displacement fields can be measured independently and defined clearly. The optical setup has the advantages of structural novelty, flexibility, and high fringe contrast. Moreover, the in-plane displacement sensitivity is twice of that of the normal moire interferometer. The measuring techniques to obtain the fringe patterns and displacement fields using the MMI-T/G system are described. The experimental results of thermal displacement of an electronic device are shown.

Three-dimensional measurement of bubble volume based on dual perspective imaging

This paper presents a new three-dimensional(3D) volume measurement approach of bubble in gas-liquid two-phase flow. According to the dual perspective imaging principle,bubble feature images can be captured from two different view angles. The least square ellipse fitting algorithm is used to figure out the feature parameters from the captured images. Then the 3D volume of bubble can be quantitatively measured. Compaerd with the traditional volume estimation methods based on single perspective imaging,it can effectively reduce the loss of bubble feature information. In the experiment,the 3D volume reconstruction of bubbles from dual perspective images is conducted,and the variation of bubble volume in the bubble rising process is studied. The results show that the measurement accuracy based on the proposed 3D method is higher than those based on traditional methods. The volume of rising bubble is periodically changed,which indicates that bubble achieves periodic rotation and deformation in the rising process.

Multi-frequency lateral shear interferometer system for simultaneous measurement of thickness and three-dimensional shape

This Letter demonstrates a novel lateral shear interferometer system for simultaneous measurement of three-dimensional （3D） shape and thickness of transparent objects. Multi-frequency fringe patterns can be created by tilting mirrors at different inclination angles. With a single camera, the multi-frequency fringes are recorded in one image. The phase-shift of the fringes can be generated synchronously only by moving a plane-parallel plate along an in-plane parallel direction. According to the feature of transparent materials, the thickness and 3D shape can be reconstructed simultaneously based on the relationship between the in-plane displacement and their characteristics. The experiment was conducted on a thin transparent film subjected to a shearing force, which verifies the feasibility of the proposed system.