Three-Dimensional Simulations of RESET Operation in Phase-Change Random Access Memory with Blade-Type Like Phase Change Layer by Finite Element Modeling

An optimized device structure for reducing the RESET current of phase-change random access memory （PCRAM） with blade-type like （BTL） phase change layer is proposed. The electrical thermal analysis of the BTL cell and the blade heater contactor structure by three-dimensional finite element modeling are compared with each other during RESET operation. The simulation results show that the programming region of the phase change layer in the BTL cell is much smaller, and thermal electrical distributions of the BTL cell are more concentrated on the TiN/GST interface. The results indicate that the BTL cell has the superiorities of increasing the heating efficiency, decreasing the power consumption and reducing the RESET current from 0.67mA to 0.32mA. Therefore, the BTL cell will be appropriate for high performance PCRAM device with lower power consumption and lower RESET current.

Simulation-Based Construction of Three-Dimensional Process Model for Punching Cartridge Cases

A method of constructing three-dimensional process model for the punching cartridge cases is presented based on DEFORM simulation analysis. Using DEFORM software,the finite element simulation models for the punching and forming process of cartridge cases are established,and the corresponding simulation result model of each intermediate procedure is obtained by continuously performing the forming process simulation. The simulation model cannot annotate size and process information due to poor interface between DEFORM software and CAD software. Thus,a 3D annotation module is developed with secondary development technology of UG NX software. Consequently,the final process model with dimension and process information is obtained. Then,with the current 3D process management system,the 3D punching and forming process design of cartridge cases can be completed further. An example is also provided to illustrate that the relative error between the simulation process model and the physical model is less than 2%,which proves the validity and reliability of the proposed method in this study.

Three-Dimensional Cerebral Aneurysm Models for Surgical Simulation and Education—Development of Aneurysm Models with Perforating Arteries and for Application of Fenestrated Clips

We modified a three-dimensional cerebral aneurysm model for surgical simulation and educational demonstration. Novel models are made showing perforating arteries arising around the aneurysm. Information about perforating arteries is difficult to obtain from individual radiological data sets. Perforators are therefore reproduced based on previous anatomical knowledge instead of personal data. Due to their fragility, perforating arteries are attached to the model using hard materials. At the same time, hollow models are useful for practicing clip application. We made a model for practicing the application of fenestrated clips for paraclinoid internal carotid aneurysms. Situating aneurysm models in the fissure of a brain model simulates the real surgical field and is helpful for educational demonstrations.

A COUPLED MODEL FOR MUILTIPHASE FLUID FLOW AND SEDIMENTATION DEFORMATION IN OIL RESERVOIR AND ITS NUMERICAL SIMULATION

A mathematical model for coupled multiphase fluid flow and sedi- mentation deformation is developed based on fluid-solid interaction mechanism.A finite difference-finite element numerical approach is presented.The results of an example show that the fluid-solid coupled effect has great influence on multiphase fluid flow and reservoir recovery performances,and the coupled model has practical significance for oilfield development.

Application of Three-Dimensional Visual Simulation in Tidal Defense Engineering

Any tidal defense engineering involves the collection and analysis of massive information about engineering structures and their surrounding environment. Traditional method, which is carried out mainly by means of twodimensional drawings and textures, is not efficient and intuitive enough to analyze the whole project and reflect its spatial relationship. Three-dimensional visual simulation provides an advanced technical means of solving this problem. In this paper, triangular irregular network (TIN) model simplified by non-uniform rational B-splines (NURBS) technique was used to establish the digital terrain model (DTM) of a super large region. Simulation of dynamic water surface was realized by combining noise function with sine wave superposition method. Models of different objects were established with different modeling techniques according to their characteristics. Application of texture mapping technology remarkably improved the authenticity of the models. Taking the tidal defense engineering in the new coastal region of Tianjin as a case study, three-dimensional visual simulation and dynamic roaming of the study area were realized, providing visual analysis and visible demonstration method for the management and emergency decision-making associated with construction.

Runoff Simulation of Shitoukoumen Reservoir Basin Based on SWAT Model

[Objective] The study aimed to simulate the runoff of Shitoukoumen Reservoir basin by using SWAT model. [Method] Based on DEM elevation, land use type, soil type and hydrometeorological data, SWAT model, a distributed hydrological model was established to simulate the monthly runoff of Shitoukoumen Reservoir basin, and the years 2006 and 2010 were chosen as the calibration and validation period respectively. [Result] The simulation results indicated that SWAT model could be used to simulate the runoff of Shitoukoumen Reservoir basin, and the simulation effect was good. However, the response of the model to local rainstorm was not obvious, so that the actual runoff in June and July of 2010 was abnormally higher than the simulation value. [Conclusion] The research could provide theoretical references for the plan and management of water resources in Shitoukoumen Reservoir basin in future.

Simulation and Modelling of Water Injection for Reservoir Pressure Maintenance

Water injection has shown to be one of the most successful,efficient,and cost-effective reservoir management strategies.By re-injecting treated and filtered water into reservoirs,this approach can help maintain reservoir pressure,increase hydrocarbon output,and reduce the environmental effect.The goal of this project is to create a water injection model utilizing Eclipse reservoir simulation software to better understand water injection methods for reservoir pressure maintenance.A basic reservoir model is utilized in this investigation.For simulation designs,the reservoir length,breadth,and thickness may be changed to different levels.The water-oil contact was discovered at 7000 feet,and the reservoir pressure was recorded at 3000 pounds per square inch at a depth of 6900 feet.The aquifer chosen was of the Fetkovich type and was linked to the reservoir in the j+direction.The porosity was estimated to be varied,ranging from 9%to 16%.The residual oil saturation was set to 25%and the irreducible water saturation was set at 20%.The vertical permeability was set at 50 md as a constant.Pressure Volume Temperature(PVT)data was used to estimate the gas and water characteristics.

Simulation-optimization model of reservoir operation based on target storage curves

This paper proposes a new storage allocation rule based on target storage curves. Joint operating rules are also proposed to solve the operation problems of a multi-reservoir system with joint demands and water transfer-supply projects. The joint operating rules include a water diversion rule to determine the amount of diverted water in a period, a hedging rule based on an aggregated reservoir to determine the total release from the system, and a storage allocation rule to specify the release from each reservoir. A simulation-optimization model was established to optimize the key points of the water diversion curves, the hedging rule curves, and the target storage curves using the improved particle swarm optimization （IPSO） algorithm. The multi-reservoir water supply system located in Liaoning Province, China, including a water transfer-supply project, was employed as a case study to verify the effectiveness of the proposed join operating rules and target storage curves. The results indicate that the proposed operating rules are suitable for the complex system. The storage allocation rule based on target storage curves shows an improved performance with regard to system storage distribution.

The numerical simulation for a 3D two-phase anisotropic medium based on BISQ model

Biot-flow and squirt-flow are the two most important fluid flow mechanisms in porous media containing fluids. Based on the BISQ （Biot-Squirt） model where the two mechanisms are treated simultaneously, the elastic wave-field simulation in the porous medium is limited to two-dimensions and two-components （2D2C） or two-dimensions and three-components （2D3C）. There is no previous report on wave simulation in three- dimensions and three-components. Only through three dimensional numerical simulations can we have an overall understanding of wave field coupling relations and the spatial distribution characteristics between the solid and fluid phases in the dual-phase anisotropic medium. In this paper, based on the BISQ equation, we present elastic wave propagation in a three dimensional dual-phase anisotropic medium simulated by the staggered-grid high-order finite-difference method. We analyze the resulting wave fields and show that the results are an improvement.

Microscopic sand production simulation and visual sanding pattern description in weakly consolidated sandstone reservoirs

To visually describe the sanding pattern,this study constructs a new particle-scale microstructure model of weakly consolidated formation,and develop the corresponding methodology to simulate the sanding process and predict sand cavity shape.The microstructure model is a particle-objective model,which focuses on the random sedimentation of every sand grain.In the microstructure,every particle has its own size,sphericity and inclination angle.It is used to simulate the actual structure of cemented granular materials,which considers the heterogeneity and randomness of reservoir properties,provides the initial status for subsequent sanding simulation.With the particle detachment criteria,the microscopic simulation of sanding can be visually implemented to investigate the pattern and cavity shapes caused by sand production.The results indicate that sanding always starts initially from the borehole border,and then extends along the weakly consolidated plane,showing obvious characteristic of randomness.Three typical microscopic sanding patterns,concerning pore liquefaction,pseudo wormhole and continuous collapse,are proposed to illustrate the sanding mechanism in weakly consolidated reservoirs.The nonuniformity of sanding performance depends on the heterogeneous distribution of reservoir properties,such as rock strength and particle size.Finally,the three sanding patterns are verified by visually experimental work.The proposed integrated methodology is capable of predicting and describing the sanding cavity shape of an oil well after long-term sanding production,and providing the focus objective of future sand control measure.

A Three-Dimensional Water Quality Model and Its Application to Jiaozhou Bay, China

A three-dimensional coupled physical and water quality model was developed and applied to the Jiaozhou Bay to study water quality involving nutrients, biochemical oxygen demand, dissolved oxygen, and phytoplankton that are closely related to eutrophication process. The physical model is a modified ECOM-si version with inclusion of flooding/draining processes over the intertidal zone. The water quality model is based on WASP5 which quantifies processes governing internal nutrients cycling, dissolved oxygen balance and phytoplankton growth. The model was used to simulate the spatial distribution and the temporal variation of water quality in the Jiaozhou Bay for the period of May 2005 to May 2006. In addition, the effect of reduction of riverine nutrients load was simulated and evaluated. The simulated results show that under the influence of nutrients discharged from river, the concentrations of nutrients and phytoplankton were higher in the northwest and northeast of the bay, and decreased from the inner bay to the outer. Affected by strong tidal mixing, the concentrations of all state variables were vertically homogeneous except in the deeper regions where a small gradient was found. Obvious seasonal variation of phytoplankton biomass was found, which exhibited two peaks in March and July, respectively. The variation of riverine waste loads had remarkable impact on nutrients concentration in coastal areas, but slightly altered the distribution in the center of the bay.

Simulation of water temperature distribution in Fenhe Reservoir

In order to evaluate the need of controlling the temperature of water discharged from the Fenhe Reservoir, the reservoir water temperature distribution was examined. A three-dimensional mathematical model was used to simulate the in-plane and vertical distribution of water temperature. The parameters of the model were calibrated with field data of the temperature distribution in the Fenhe Reservoir. The simulated temperature of discharged water is consistent with the measured data. The difference in temperature between the discharged water and the natural river channel is less than 3 ℃ under the current operating conditions. This will not significantly impact the environment of downstream areas.

Three-dimensional tidal current numerical model of the Oujiang Estuary

The characteristics of three-dimensional （3-D） tidal current in the Oujiang Estuary are investigated according to in situ observations. The Oujiang Estuary has features of irregular coastline, complex topography, many islands, moveable boundary, and submerged dyke, therefore, σ 3-D numerical model oil an unstructured triangular grid has been degeloped. The σ coordinate transforination, the moveable boundary and submerged dyke treatment techniques were employed in the model so it is suitable for the tidal simulations in the Oujing Estuary with submerged dyke and moveable boundary problems. The model is evaluated with the in situ data, and the results show that the calculated water elevations at 19 stations and currents at 19 profiler stations are in good agreement with measured data both in magnitude and phase. This numerical model is applied to the 3-D tidal circulation simulations of experiments in stopping flow transport through the South Branch of the Oujiang Estuary, and the feasibility to cutoff the flow in the South Branch of the Oujiang Estuary is demonstrated by numerical simulation experiments. The developed numerical model simulated the 3-D tidal current circulations in complicated coastal and estuarine waters very well.

Nonlinear flow numerical simulation of low-permeability reservoir

A nonlinear flow reservoir mathematical model was established based on the flow characteristic of low-permeability reservoir.The well-grid equations were deduced and the dimensionless permeability coefficient was introduced to describe the permeability variation of nonlinear flow.The nonlinear flow numerical simulation program was compiled based on black-oil model.A quarter of five-spot well unit was simulated to study the effect of nonlinear flow on the exploitation of low-permeability reservoir.The comprehensive comparison and analysis of the simulation results of Darcy flow,quasi-linear flow and nonlinear flow were provided.The dimensionless permeability coefficient distribution was gained to describe the nonlinear flow degree.The result shows that compared with the results of Darcy flow,when considering nonlinear flow,the oil production is low,and production decline is rapid.The fluid flow in reservoir consumes more driving energy,which reduces the water flooding efficiency.Darcy flow model overstates the reservoir flow capability,and quasi-linear flow model overstates the reservoir flow resistance.The flow ability of the formation near the well and artificial fracture is strong while the flow ability of the formation far away from the main streamline is weak.The nonlinear flow area is much larger than that of quasi-linear flow during the fluid flow in low-permeability reservoir.The water propelling speed of nonlinear flow is greatly slower than that of Darcy flow in the vertical direction of artificial fracture,and the nonlinear flow should be taken into account in the well pattern arrangement of low-permeability reservoir.

NUMERICAL SIMULATION OF SOUTH CHINA SEA MONSOON ONSET BASED ON GRAPES MODEL AND EXPERIMENTS ON INITIAL MODEL FIELDS

The Global and Regional Assimilation and Prediction System (GRAPES), a limited-area regional model, was used to simulate the onset of South China Sea summer monsoon. In view of the relatively insufficient information about the initial field in simulation predictions, the Advanced Microwave Sounding Unit-B (AMSU-B) data from a NOAA satellite were introduced to improve the initial values. By directly using the 3-dimensional variational data assimilation system of GRAPES, two schemes for assimilation tests were designed. In the design, Test 1 (T1) assimilates both sounding and AMSU-B data, and Test 2 (T2) assimilates only the conventional sounding data, before applying the model in simulation forecasts. Comparative experiments showed that the model was very sensitive to initial fields and successful in reproducing the monsoon onset, allocation of high- and low-level wind fields during the pentad of onset, and the northward advancement of the monsoon and monsoon rain bands. The scheme, however, simulated rainfall and the location of the subtropical high with deviations from observations. The simulated location of the subtropical high was more westward and northward and the simulated rainfall for the South China Sea was larger and covered a broader area.

3D Modeling and Simulation of Fancy Fabrics in Weft Knitting

Weft knitted fancy fabrics are widely used in knitted garment design. Due to the complexity of the structures, their modeling and simulation needs to be solved in three-dimensional (3D) CAD developments. In this paper, 3D loop geometrical models of weft knitted fancy structures, including tuck stitch, jacquard stitch, transfer stitch and fleecy stitch, were developed based on an improved model of plain loop, and their central axes as some 3D space curves were achieved by using Non-Uniform Rational B-Splines (NURBS). The 3D visual simulation programme was written in C++ programming language using OpenGL, which was a function library of 3D graphics. Some examples of weft knitted fancy fabrics were generated and practical application of 3D simulation was discussed.

The 3D simulation and optimized management model of groundwater systems based on eco-environmental water demand

Through the study of mutual process between groundwater systems and eco-environmental water demand, the eco-environmental water demand is brought into groundwater systems model as the important water consumption item and unification of groundwater抯 economic, environmental and ecological functions were taken into account. Based on eco-environmental water demand at Da抋n in Jilin province, a three-dimensional simulation and optimized management model of groundwater systems was established. All water balance components of groundwater systems in 1998 and 1999 were simulated with this model and the best optimal exploitation scheme of groundwater systems in 2000 was determined, so that groundwater resource was efficiently utilized and good economic, ecologic and social benefits were obtained.

A Simulation Approach for Screening of EOR Scenarios in Naturally Fractured Reservoirs

Undoubtedly, plenty of hydrocarbon sources are located in carbonate rocks, particularly those which are naturally fractured that is still needed to study their characterization, because of their complex and unconventional behavior. Therefore, applying any processes that cause Enhancing Oil Recovery (EOR) from Naturally Fractured Reservoirs (NFR) seems necessary and useful. However, selecting the best developed scenario is always challenging. Screening criteria would determine the possibility of implementing an EOR process. While, utilizing trade marketing simulators can solve this problem. Moreover, simulation can evaluate other parameters such as water cut and gas-oil ratio. In this research, an aquifer-supported Iranian NFR with two parts that are separated to each other with a shale layer is considered in order to select the best EOR scenario. The fluid model is created using PVTi software. Various production scenarios included natural depletion, water flooding, miscible carbon dioxide injection, water-alternating-gas (WAG) injection, simultaneous water- alternating-gas (SWAG) injection, hybrid injection, and gas recycling are simulated in ECLIPSE Compositional (E300) and their recovery factor recorded as the target parameter. The developed scenarios are designed in a way that gives the optimized results, i.e. higher recovery factor, less water cut as well as the less gas-oil ratio. As a result, SWAG shows better conditions and is recommended for the further studies of the reservoir management plan in the future. Also, the role of the aquifer in the SWAG scenario is positive by creating a natural WAG in addition to the SWAG. Additionally, the average reservoir pressure through fractures reduces less in the SWAG than the other Scenarios, the oil and gas production rate reduce less in the SWAG and SWAG/ miscible gas respectively than the other scenarios. The maximum and the minimum water cut are related to the water flooding and SWAG, respectively.Finally, the simulation approach of EOR screening in NFR is better than other approaches, from the perspective of economic issues as well as the simplicity of the methods.

A New Method to Determine the Grid Directions in Reservoir Numerical Simulation

Grid direction selection and grid size design are two important elements that need to be considered in the grid direction design in reservoir numerical simulation. Reservoir engineers normally utilize geological data (such as the distribution of fractures, low permeability zones, faults and major stress) and simulation experiences to design the grid direction of simulation model qualitatively. The research of the paper indicates that the key to determine the grid direction is to determine the principal permeability direction. Under the circumstances of few static materials, a new grid direction determination method has been developed by using field data (well location map and inter-well permeability) on the bases of Darcy’s law and tensor analysis theory. The grid direction of WZ11-7 Oilfield simulation model has been determined using four production wells and two production zones (L1 and L3) in WZ11-7-2 well group, the results are in conformity with the geological studied major stress. Therefore, this method can give insights into the numerical simulation study.

Three-Dimensional Visual Analysis for Construction Layout of Reservoir Project

It is difficult to analyze the inter-relationship for the construction layout of a reservoir project scientifically and intuitively.According to the characteristics of broad field and huge information,the modeling methods of digital terrain and solid model as well as the techniques of texture mapping and scene navigation are adopted.The simulation system is developed by C program language,which includes the functions of the interactive navigation of 3D scene,the visual inquiry of project digital model information,the storage and management of project information.A certain reservoir is taken as a case.The 3D visual analysis for the construction layout and engineering information are obtained.The proposed system is of great advantages in dealing with large amount of information and the method provides a theoretical basis and technical support for the construction layout of a reservoir project.