Three-Dimensional Rotational Angiography in Congenital Heart Disease:Estimation of Radiation Exposure

Objectives: There is an increasing use of three-dimensional rotational angiography (3D-RA) during catheterization of congenital heart disease. Dose-area-product (DAP) measured by the angiography system and computed-tomography dose index (CTDI) do not appear practical for dose assessment. Hence, we performed real dose measurements in anthropomorphic phantoms. Methods: Three different anthropomorphic phantoms (10 kg, 19 kg and 73 kg bodyweight) equipped with thermoluminescent dosimeters (TLD) were used. We used a typical standard diagnostic program and a low-dose program. The effective dose (ED) was calculated according to the International Commission on Radiological Protection (ICRP) 103. The 3D distribution of radiation in the body was assessed. Results: ED for the male 10 kg phantom was 0.192 mSv in the diagnostic program and 0.050 mSv (male) in the low-dose program. The 19 kg phantom received an ED of 0.205 mSv (male) in the diagnostic program. In the low-dose program the ED reached 0.058 mSv (male). The male adult 73 kg phantom was exposed with an ED of 0.730 mSv in the diagnostic program and 0.282 mSv in the low-dose program. ED for the female phantoms was slightly higher for both acquisition-programs. Dose distribution was inhomogeneous with a dose maximum in the esophageal region behind the heart, whereas in the brain, intestine and gonads we found nearly no radiation. Conclusions: 3D-RA imaging in the interventional catheter laboratory is possible with an effective dose lower than 1 mSv. With its potential to reduce fluoroscopic time and the number of control angiographies in catheterization and intervention in complex anatomy, it can decrease the radiation dose.

Preoperative diagnosis and operative effect of intracranial aneurysm with three-dimensional computed tomography angiography

BACKGROUND ： Digital subtraction angiography （DSA） is always regarded as the golden standard for diagnosis of intracranial aneurysm; however, the procedure is complex, traumatic, expensive and easy to induce vascular complication. Three-dimensional computed tomography angiography （3D-CTA） can make up deficiencies of DSA; therefore, it is used in clinical therapy wider and wider. OBJECTIVE ： To evaluate the clinical effect of 3D-CTA on disruption and hemorrhage of intracranial aneurysm pre- and post-operation and compare with the effect of DSA. DESIGN ： Auto-control contrast observation SETTING ： Department of Neurosurgery, Shengjing Hospital of China Medical University PARTICIPANTS ： A number of 106 patients with disruption and hemorrhage of intracranial aneurysm were selected from the Department of Neurosurgery, Shengjing Hospital of China Medical University from January 2003 to April 2006. All patients were diagnosed with cranial operation and consent. There were 47 males and 59 females aged from 3-76 years with the mean age of （47±13） years. Among them, 82 patients had extensive subarachnoid hemorrhage （SAH）, 7 had hemorrhage at longitudinal fissure, and 17 had hemorrhage at ambiens cistema and lateral fissure. Moreover, intraventricular hematocele was accompanied on 13 patients and hematom on 9 patients. METHODS： （1） 3D-CTA examination： Siemens SOMATOM Sensation 64 CT was used in this study. The thickness was 1 mm and interval of reconstruction was 0.8 mm. Localizing section was plainly scanned as the standard of canthus line. Scan ranged from 30 mm below sella to 50 mm above sella. Non-ion contrast medium of Omnipaque 350 （concentration of iodine was 350 g/L） was inserted into anterior vein of elbow with 18G trochar retained with high-pressured injectoc pum. The speed was 4.5 mL/s and the total volume was 80-100 mL with the means of 90 mL. Scan started at 10-20 s after injection of contrast medium. Original image was dealt with Leonardo workstation and retreated with Syngo software. Volume rendering and maximum intensity projection were used to reconstructed images, （2） All 106 patients suffered from occlusion of aneurysm clamp. Before operation, 3D-CTA was undertaken and DSA was followed. After operation, patients were rechecked with 3D-CTA. MAIN OUTCOME MEASURES： Comparisons between 3D-CTA and DSA. RESULTS ： All 106 patients were involved in the final analysis. （1） Examination of 3D-CTA and DSA： Among 118 patients with aneurysm, 110 were checked with 3D-CTA and the detected rate was 93.2% （110/118）. Among other 8 cases, 3 were negative and checked again with DSA; 1 had pericallosal aneurysm, 1 ophthalmic aneurysm, and 1 anterior choroidal artery of aneurysm. 3D-CTA results of other 5 cases were suspicious, and then, they were regarded as having aneurysm with DSA. Before operation, correlation among site, body, neck of aneurysm and peripheral anatomic structure were shown sufficiently. After operation, 82 patients were rechecked with 3D-CTA, which was complete occlusion, precise, unobvious constriction, emphraxis or remains as compared with 3D-CTA those pre-operation. （2） Characteristics of 3D-CTA： With multiple vessels and angles, 3D-CTA observed the relationship between aneurysm neck and carried artery and showed thrombosis in cavity of aneurysm, calcification of aneurysm wall and peripheral structure of vessel at the same time. However, DSA could not detect the reactions mentioned above. It could delete image of cranium, simulate image of operative route, eliminate artifact induced by metal, but not distinguish blood stream direction. Meanwhile, posterior communicating artery was always poor during circle of Willis artery showing. CONCLUSION： （1） 3D-CTA is characterized by simple operation and non-invasive showing vascular stereo structure and correlation. Therefore, it is significant for diagnosis and designing plan of operative approach and focal location pre-operation and evaluating effect post-operation. （2） 3D-CTA does not completely replace DSA on the diagnosis of intracranial aneurysm.

Thoracoscopic segmentectomy assisted by three-dimensional computed tomography bronchography and angiography for lung cancer in a patient living with situs inversus totalis: A case report

BACKGROUND Situs inversus totalis(SIT)is a rare congenital condition that is characterized by a complete mirror image of the typical arrangement of the thoracic and abdominal viscera.Performing thoracoscopic segmentectomy for a patient with lung cancer and SIT is an extremely skilled and challenging surgical procedure.CASE SUMMARY A 41-year old woman with a medical history of dextrocardia since childhood was admitted to our hospital with a mixed ground-glass opacity(mGGO)in her left lung field,discovered by computed tomography during her health checkup.In order to facilitate surgical orientation,three-dimensional computed tomography bronchography and angiography(3D-CTBA)was preoperatively carried out.The result of 3D-CTBA was consistent with the diagnosis of SIT and an mGGO in the posterior segment of the left upper lobe(LS2).Surgery was conducted in accordance with preoperative 3D-CTBA and designed surgical procedure,combined with intraoperative navigation.Final pathological examination revealed in situ adenocarcinoma.The patient’s postoperative condition was uneventful and no complications were observed.CONCLUSION We present the first case of lung cancer in a patient with SIT who successfully underwent thoracoscopic segmentectomy assisted by 3D-CTBA.This is a new technique that covers precise confirmation and dissection of targeted structures and intersegmental demarcation,and can help achieve a meticulous anatomical segmentectomy.

Reflection of three-dimensional plane waves at the free surface of a rotating triclinic half-space under the context of generalized thermoelasticity

The reflection of three-dimensional(3D) plane waves in a highly anisotropic(triclinic) medium under the context of generalized thermoelasticity is studied. The thermoelastic nature of the 3D plane waves in an anisotropic medium is investigated in the perspective of the three-phase-lag(TPL), dual-phase-lag(DPL), Green-Naghdi-III(GNIII), Lord-Shulman(LS), and classical coupled(CL) theories. The reflection coefficients and energy ratios for all the reflected waves are obtained in a mathematical form. The rotational effects on the reflection characteristics of the 3D waves are discussed under the context of generalized thermoelasticity. Comparative analyses for the reflection coefficients of the waves among these generalized thermoelastic theories are performed. The energy ratios for each of the reflected waves establish the energy conservation law in the reflection phenomena of the plane waves. The highly anisotropic materials along with the rotation may have a significant role in the phenomenon of the reflection behavior of the 3D waves. Numerical computations are performed for the graphical representation of the study.

Three-dimensional time-of-flight magnetic resonance angiography combined with high resolution T2-weighted imaging in preoperative evaluation of microvascular decompression

BACKGROUND Neurovascular compression(NVC) is the main cause of primary trigeminal neuralgia(TN) and hemifacial spasm(HFS). Microvascular decompression(MVD) is an effective surgical method for the treatment of TN and HFS caused by NVC. The judgement of NVC is a critical step in the preoperative evaluation of MVD, which is related to the effect of MVD treatment. Magnetic resonance imaging(MRI) technology has been used to detect NVC prior to MVD for several years. Among many MRI sequences, three-dimensional time-of-flight magnetic resonance angiography(3D TOF MRA) is the most widely used. However, 3D TOF MRA has some shortcomings in detecting NVC. Therefore, 3D TOF MRA combined with high resolution T2-weighted imaging(HR T2WI) is considered to be a more effective method to detect NVC.AIM To determine the value of 3D TOF MRA combined with HR T2WI in the judgment of NVC, and thus to assess its value in the preoperative evaluation of MVD.METHODS Related studies published from inception to September 2022 based on PubMed, Embase, Web of Science, and the Cochrane Library were retrieved. Studies that investigated 3D TOF MRA combined with HR T2WI to judge NVC in patients with TN or HFS were included according to the inclusion criteria. Studies without complete data or not relevant to the research topics were excluded. The Quality Assessment of Diagnostic Accuracy Studies checklist was used to assess the quality of included studies. The publication bias of the included literature was examined by Deeks’ test. An exact binomial rendition of the bivariate mixed-effects regression model was used to synthesize data. Data analysis was performed using the MIDAS module of statistical software Stata 16.0. Two independent investigators extracted patient and study characteristics, and discrepancies were resolved by consensus. Individual and pooled sensitivities and specificities were calculated. The I_(2) statistic and Q test were used to test heterogeneity. The study was registered on the website of PROSERO(registration No. CRD42022357158).RESULTS Our search identified 595 articles, of which 12(including 855 patients) fulfilled the inclusion criteria. Bivariate analysis showed that the pooled sensitivity and specificity of 3D TOF MRA combined with HR T2WI for detecting NVC were 0.96 [95% confidence interval(CI): 0.92-0.98] and 0.92(95%CI: 0.74-0.98), respectively. The pooled positive likelihood ratio was 12.4(95%CI: 3.2-47.8), pooled negative likelihood ratio was 0.04(95%CI: 0.02-0.09), and pooled diagnostic odds ratio was 283(95%CI: 50-1620). The area under the receiver operating characteristic curve was 0.98(95%CI: 0.97-0.99). The studies showed no substantial heterogeneity(I2 = 0, Q = 0.001 P = 0.50).CONCLUSION Our results suggest that 3D TOF MRA combined with HR T2WI has excellent sensitivity and specificity for judging NVC in patients with TN or HFS. This method can be used as an effective tool for preoperative evaluation of MVD.

Giant Asymmetric Transmission and Optical Rotation of a Three-Dimensional Metamaterial

We show that giant asymmetric transmission and optical rotation for linear polarizations can be achieved by a chiral three-dimensional metamaterial composed of L-shaped and C-shaped metallic particles. Numerical calcu- lations on the electric field distributions indicate that the coupling between the electric dipolar and quadrupolar resonances in the L- and C-shaped metallic particles contributes to these effects.

Three-dimensional channel flow of second grade fluid in rotating frame

An analysis is performed for the hydromagnetic second grade fluid flow between two horizontal plates in a rotating system in the presence of a magnetic field. The lower sheet is considered to be a stretching sheet, and the upper sheet is a porous solid plate. By suitable transformations, the equations of conservation of mass and momentum are reduced to a system of coupled non-linear ordinary differential equations. A series of solutions to this coupled non-linear system are obtained by a powerful analytic technique, i.e., the homotopy analysis method （HAM）. The results are presented with graphs. The effects of non-dimensional parameters R, A, M2, a, and K2 on the velocity field are discussed in detail.

The value of three-dimensional computed tomographic angiography in the early diagnosis and treatment of spontaneous subarachnoid hemorrhage (616 cases report)

Objective To evaluate the clinical value of three dimensional computerized tomography angiography in the diagnosis and treatment of spontaneous subarachnoid hemorrhage. Methods 616 cases were diagnosed as suspected intracranial aneurysms in 3D CTA system. Computed tomographic scans and CTA studies were

Three-dimensional Imaging of Multi-slice Spiral CT in Bronchial Artery Correlative Study on Blood Supply of Central Lung Cancer and Its Clinical Significance

Objective: To evaluate three-dimensional bronchial artery imaging charactersin central lung cancer and applied values with multi-slice spiral CT (MSCT) to provide theoreticalevidence on blood supply and intervention therapy. Methods: Eighteen patients with central lungcancer underwent MSCT with real time helical thin-slice CT scanning. Three-dimensional bronchialartery reconstruction was done at the console work-station. The space anatomical characters ofbronchial artery were observed through different rotations. Results: For 6 cases, thethree-dimensional images of bronchial artery (33.33%) could exactly show the origins, the routes(lung inner segment and mediatism segment) and the diameters of bronchial arteries. Vision rate ofbronchial arteries was the highest in pulmonary artery stricture and truncation groups, and thevessels' diameter became larger apparently. These characters demonstrated blood supply of this kindof central lung cancer come from bronchial artery. Volume rendering images were the best ones amongthree-dimensional images. Conclusion: Three-dimensional imaging with MSCT in bronchial artery canreveal the anatomical characters of bronchial artery and provide theoretical evidence on bloodsupply and intervention therapy of central lung cancer.

Three-dimensional analysis of slopes reinforced with piles

Based on the upper bound of limit analysis, the plane-strain analysis of the slopes reinforced with a row of piles to the 3D case was extended. A 3D rotational failure mechanism was adopted to yield the upper bound of the factor of safety. Parametric studies were carried out to explore the end effects of the slope failures and the effects of the pile location and diameter on the safety of the reinforced slopes. The results demonstrate that the end effects nearly have no effects on the most suitable location of the installed piles but have significant influence on the safety of the slopes. For a slope constrained to a narrow width, the slope becomes more stable owing to the contribution of the end effects. When the slope is reinforced with a row of piles in small space between piles, the effects of group piles are significant for evaluating the safety of slopes. The presented method is more appropriate for assessing the stability of slopes reinforced with piles and can be also utilized in the design of plies stabilizing the unstable slopes.

Aggressive plaque modification with rotational atherectomy and cutting balloon for optimal stent expansion in calcified lesions

Objective To evaluate the factors affecting optimal stentt expansion in calcified lesions treated by aggressive plaque modification with rotational atherectomy （RA） and a cutting balloon （CB）. Methods From January 2014 to May 2015, 92 patients with moderate to severe coronary calcified lesions underwent rotational atherectomy and intravascular ultrasound imaging at Chinese PLA General Hospital （Beijing, China） were included in this study, They were divided into a rotational artherectomy combined with cutting balloon （RACB） group （46 patients treated with RA followed by CB angioplasty） and an RA group （46 patients treated with RA followed by plain balloon angioplasty）. Another 40 patients with similar severity of their calcified lesions treated with plain old balloon angioplasty （POBA） were de- mographically matched to the other groups and defined as the POBA group. All patients received a drug-eluting stent after plaque prepara- tion. Lumen diameter and lumen diameter stenosis （LDS） were measured by quantitative coronary angiography at baseline, after RA, after dilatation, and after stenting. Optimal stent expansion was defined as the final LDS 〈 10%. Results The initial and post-RA LDS values were similar among the three groups. However, after dilatation, the LDS significantly decreased in the RACB group （from 54.5% ± 8.9% to 36.1%＋ 7.1%） but only moderately decreased （from 55.7% ± 7.8% to 46.9% ± 9.4%） in the RA group （time × group, P 〈 0.001）. After stenting, there was a higher rate of optimal stent expansion in the RACB group （71.7% in the RACB group, 54.5% in the RA group, and 15% in the POBA group, P 〈 0.001）, and the final LDS was significantly diminished in the RACB group compared to the other two groups （6.0% ± 2.3%, 10.8% ± 3.3%, 12.7% ± 2.1%, P 〈 0.001）. Moreover, an LDS 〈 40% after plaque preparation （OR = 2.994, 95% CI： 1.297-6.911） was associated with optimal stent expansion, which also had a positive correlation with the appearance of a calcified ring split （r = 0,581, P 〈 0.001）. Conclusions Aggressive plaque modification with RA and CB achieve more optimal stent expansion. An LDS ≤ 40% after plaque modification was a predictive factor for optimal stent expansion in calcified lesions. This parameter was also associated with the presence of calcified ring split.

全脑血管造影术后即刻采用轴线翻身法的临床效果

目的 探讨全脑血管造影术后即刻采用轴线翻身法对患者穿刺点出血情况、腰背部疼痛及满意度的影响。方法 选取2021年6月至2022年6月解放军总医院第一医学中心神经内科医学部收治的236例行全脑血管造影术患者为研究对象,按照随机数字表法将其分为对照组和观察组,每组118例。对照组术后采用常规护理,平卧6 h后进行轴线翻身;观察组术后即刻采用轴线翻身法翻身。比较两组穿刺点出血情况、腰背部疼痛程度及满意度。结果 两组穿刺点皮下血肿、少量渗血、明显出血发生率比较,差异无统计学意义(P>0.05)。观察组腰背部视觉模拟评分法评分低于对照组,满意度高于对照组,差异有统计学意义(P<0.05)。结论 全脑血管造影术后即刻采用轴线翻身法,可降低患者腰背部疼痛程度,改善术后舒适度,提高满意度,且即刻轴线翻身法并不增加穿刺点出血发生率。

3D-DSA与Dyna-CT在颅内支架置入术中的临床应用研究

目的探讨三维DSA血管成像(3D-DSA)及数字平板造影机的C臂旋转并断层重建技术(DynaCT)在颅内支架置入术患者中的临床应用。方法选择2019年1月-2020年6月厦门大学附属中山医院收治92例颅内动脉狭窄患者,所有患者均行颅内支架置入术治疗,分为对照组(n=38例)和观察组(n=54例)。对照组采用3D-DSA引导,观察组采用DynaCT引导,术后进行12个月门诊随访,比较两组改良Rankin量表(mRS)评分、手术成功率、并发症、支架再狭窄及斑块检出率。结果观察组术后4个月、8个月及12个月mRS评分、支架成形术耗时低于对照组(P<0.05);观察组Dyna-CT的术前规划、观察到支架表面图像与术中所见吻合,手术成功率为83.33%,高于对照组63.16%(P<0.05);两组围术期并发症发生率无统计意义(P>0.05);观察组手术后进行12个月门诊随访,患者支架再狭窄、血管狭窄部位斑块检出率低于对照组(P<0.05)。结论DynaCT用于颅内支架置入术中能改善患者症状,缩短支架成形术耗时,有助于提高手术成功率,未增加并发症发生率,能降低血管狭窄部位斑块检出率,值得推广应用。

分时相低对比剂注射方案在颅内动脉瘤三维-数字减影血管造影成像的应用

目的 探讨分时相低剂量低流率对比剂注射方案在颅内动脉瘤三维(three-dimensional,3D)-数字减影血管造影(digital subtraction angiography,DSA)成像的临床应用价值。方法 前瞻性连续收集经计算机断层扫描血管成像(CTA)/磁共振血管造影(MRA)检查疑似或确诊颅内动脉瘤患者共69例,按照交替序贯将患者分实验组35例,常规组34例,统计分析两组患者动脉瘤成像评分、旋转造影辐射剂量及栓塞效果。结果 实验组与常规组三维重建成像对颅内动脉瘤的细节显示比较,差异无统计学意义(P=0.633)。两组间患者辐射剂量空气比释动能(air kerma,AK)、剂量-面积乘积(dose-area product,DAP)比较,差异均无统计学意义(P=0.176,P=0.765)。两组患者间栓塞效果比较,差异无统计学意义(P=0.111)。实验组患者行3D-DSA使用对比剂剂量显著少于常规组,差异有统计学意义[(9.29±0.86)mL vs.(18.00±0.00)mL,P<0.01]。结论 分时相低对比剂注射方案在颅内动脉瘤患者3D-DSA成像安全有效,应用该方案能显著减少患者的对比剂使用剂量。

旋转DSA、DSA在原发性肝癌早期诊断和TACE介入治疗中的应用价值

目的研究旋转数字减影血管造影(DSA)、DSA在原发性肝癌早期诊断和经皮动脉化疗栓塞术(TACE)介入治疗中的应用价值。方法选取2022年1月至2023年10月我院收治的100例疑似原发性肝癌患者为研究对象,均给予常规DSA、旋转DSA检查,并以病理检查结果为金标准,比较旋转DSA、DSA在原发性肝癌中的检出结果、诊断效能、病灶检出率、临床检测情况及图像质量。76例原发性肝癌患者接受TACE介入治疗,均于术后3个月给予常规DSA、旋转DSA检查,比较2种检查方式对术后残留或复发病灶的检出率。结果以病理检查结果为金标准,旋转DSA对原发性肝癌诊断敏感度、准确度、阴性预测值高于DSA(P<0.05)。旋转DSA病灶检出率高于DSA(97.79%比87.50%,P<0.05),且旋转DSA对<1 cm的病灶检出率高于DSA(91.43%比68.57%,P<0.05)。旋转DSA造影剂剂量、辐射剂量、成像次数低于DSA(P<0.05)。旋转DSA甲级片占比高于DSA(86.00%比70.00%,P<0.05)。旋转DSA介入术后残留或复发病灶检出率高于DSA(98.55%比84.06%,P<0.05)。结论旋转DSA在微小隐匿病灶和TACE介入术后残留或复发病灶检出方面优于常规DSA,在原发性肝癌早期诊断和TACE术后疗效评估中具有重要临床价值。

Thoracoscopic segmentectomy and lobectomy assisted by threedimensional computed-tomography bronchography and angiography for the treatment of primary lung cancer

BACKGROUND Anatomical segmentectomy has been proposed as a substitution for lobectomy for early-stage lung cancer.However,it requires technical meticulousness due to the complex anatomical variations of segmental vessels and bronchi.AIM To assess the safety and feasibility of three-dimensional computed-tomography bronchography and angiography(3D-CTBA)in performing video-assisted thoracoscopic surgery(VATS)for lung cancers.METHODS In this study,we enrolled 123 patients who consented to undergo thoracoscopic segmentectomy and lobectomy assisted by 3D-CTBA between May 2017 and June 2019.The image data of enhanced computed tomography(CT)scans was reconstructed three-dimensionally by the Mimics software.The results of preoperative 3D-CTBA,in combination with intraoperative navigation,guided the surgery.RESULTS A total of 59 women and 64 men were enrolled,of whom 57(46.3%)underwent segmentectomy and 66(53.7%)underwent lobectomy.The majority of tumor appearance on CT was part-solid ground-glass nodule(pGGN;55.3%).The mean duration of chest tube placement was 3.5±1.6 d,and the average length of postoperative hospital stay was 6.8±1.8 d.Surgical complications included one case of pneumonia and four cases of prolonged air leak lasting>5 d.Notably,there was no intraoperative massive hemorrhage,postoperative intensive-care unit stay,or 30-d mortality.Preoperative 3D-CTBA images can display clearly and vividly the targeted structure and the variations of vessels and bronchi.To reduce the risk of locoregional recurrence,the application of 3D-CTBA with a virtual 3D surgical margin help the VATS surgeon determine accurate distances and positional relations among the tumor,bronchial trees,and the intersegmental vessels.Three-dimensional navigation was performed to confirm the segmental structure,precisely cut off the targeted segment,and avoid intersegmental veins injury.CONCLUSION VATS and 3D-CTBA worked in harmony in our study.This combination also provided a new pattern of transition from lesion-directed location of tumors to computer-aided surgery for the management of early lung cancer.

Multislice spiral CT angiography in evaluation of liver transplantation candidates

BACKGROUND: Orthotopic liver transplantation has be- come the treatment of choice for patients with end-stage liver disease. This study was designed to study whether multislice spiral CT angiography (MSCTA) could be used for preoperative evaluation for orthotopic liver transplanta- tion candidates. METHODS: Eighty consecutive potential candidates for liver transplantation were evaluated with dual-phase three-di- mensional CT angiography (3DCTA). The arterial-phase was used to create vascular maps of the celiac axis (inclu- ding the origin of the hepatic common artery, left gastric artery and splenic artery) and origin of the superior mesen- teric artery. The portal venous-phase was used to analyze portal vein thrombosis and collateral vascularization of the portal vein. Statistical analyses were made using the chi- square test for differences between hepatic arterial anatomy of 80 patients and Michel's anatomy of 200 patients. Appearance of MSCTA and operative results of 16 patients were analyzed. RESULTS; Sixty-two patients (77.5%) showed conven- tional and 18 (22.5%) nonconventional hepatic arterial anatomy. A significant difference was found between the two groups in anatomy of the hepatic artery (P <0.05). Celiac axis stenosis was observed in 6 patients, SA aneu- rysm in 2, small-caliber hepatic arterial vessels in 2, and portal vein thrombosis in 15. Vascular structures of 16 ope- rative patients were well defined. CONCLUSION: As a noninvasive examination, MSCTA can provide a comprehensive preoperative vascular evalua- tion for liver transplantation candidates.

Cerebral blood flow volume measurements of the carotid artery and ipsilateral branches using two-dimensional phase-contrast magnetic resonance angiography

The optimal velocity encoding of phase-contrast magnetic resonance angiography （PC MRA） in measuring cerebral blood flow volume （BFV） ranges from 60 to 80 cm/s. To verify the accuracy of two-dimensional （2D） PC MRA, the present study localized the region of interest at blood vessels of the neck using PC MRA based on three-dimensional time-of-flight sequences, and the velocity encoding was set to 80 cm/s. Results of the measurements showed that the error rate was 7.0±6.0% in the estimation of BFV in the internal carotid artery, the external carotid artery and the ipsilateral common carotid artery. There was no significant difference, and a significant correlation in BFV between internal carotid artery ＋ external carotid artery and ipsilateral common carotid artery. In addition, the BFV of the common carotid artery was correlated with that of the ipsilateral internal carotid artery. The main error was attributed to the external carotid artery and its branches. Therefore, after selecting the appropriate scanning parameters and protocols, 2D PC MRA is more accurate in the determination of BFV in the carotid arteries.

Three‑Dimensional Numerical Study on the Metal Rotating Spray Transfer Process of High‑Current GMAW

A three-dimensional numerical model based on the volume-of-fluid(VOF)method is typically preferred for studying high-current gas metal arc welding(GMAW)metal transfer mechanism and then controlling it.It is informed that the rotating spray transfer is extremely complicated,and some researchers have focused on simplified models without considering the energy conservation to make analysis manageable for the unstable metal transfer process.Using our created numerical model,the metal transfer of high-current GMAW with shielding gas of different conductivities has been studied by analyzing acting forces and fluid flows in the metal liquid column,especially for the contributions of the self-induced electromagnetic force,equivalent volume force of the capillary pressure of the surface tension(Named surface tension force in this work),static arc pressure.It is found that the unbalanced electromagnetic force greatly promotes the metal rotating motion in 500 A metal inert gas(MIG)welding with pure argon shielding gas and it pushes the metal liquid column to rotate.Considering the arc constricting effect in active shielding gas by simply changing the arc conductivity,it is found that the metal liquid column no longer rotates,it turns to swing since the unbalanced electromagnetic force is large enough to break the rotating motion.The calculated results of the metal liquid column deflected angle and rotating/swing frequency agree well with the experiment of high-speed camera observations.

Two and Three Dimensions of Generalized Thermoelastic Medium without Energy Dissipation under the Effect of Rotation

The purpose of this paper is to study the effect of rotation on the general three-dimensional model of the equations of the generalized thermoelasticity for a homogeneous isotropic elastic half-space solid. The problem is studied in the context of the Green-Naghdi theory of type II (without energy dissipation). The normal mode analysis is used to obtain the expressions for the temperature, thermal stress, strain and displacement. The distributions of variables considered are represented graphically.