Optimization Control of Multi-Mode Coupling All-Wheel Drive System for Hybrid Vehicle

The all-wheel drive(AWD)hybrid system is a research focus on high-performance new energy vehicles that can meet the demands of dynamic performance and passing ability.Simultaneous optimization of the power and economy of hybrid vehicles becomes an issue.A unique multi-mode coupling(MMC)AWD hybrid system is presented to realize the distributed and centralized driving of the front and rear axles to achieve vectored distribution and full utilization of the system power between the axles of vehicles.Based on the parameters of the benchmarking model of a hybrid vehicle,the best model-predictive control-based energy management strategy is proposed.First,the drive system model was built after the analysis of the MMC-AWD’s drive modes.Next,three fundamental strategies were established to address power distribution adjustment and battery SOC maintenance when the SOC changed,which was followed by the design of a road driving force observer.Then,the energy consumption rate in the average time domain was processed before designing the minimum fuel consumption controller based on the equivalent fuel consumption coefficient.Finally,the advantage of the MMC-AWD was confirmed by comparison with the dynamic performance and economy of the BYD Song PLUS DMI-AWD.The findings indicate that,in comparison to the comparative hybrid system at road adhesion coefficients of 0.8 and 0.6,the MMC-AWD’s capacity to accelerate increases by 5.26%and 7.92%,respectively.When the road adhesion coefficient is 0.8,0.6,and 0.4,the maximum climbing ability increases by 14.22%,12.88%,and 4.55%,respectively.As a result,the dynamic performance is greatly enhanced,and the fuel savings rate per 100 km of mileage reaches 12.06%,which is also very economical.The proposed control strategies for the new hybrid AWD vehicle can optimize the power and economy simultaneously.

Research on the quasi-isentropic driving model of aluminized explosives in the detonation wave propagation direction

Taking CL-20(Hexanitrohexaazaisowurtzitane)-based aluminized explosives with high gurney energy as the research object, this research experimentally investigates the work capability of different aluminized explosive formulations when driving metal flyer plates in the denotation wave propagation direction.The research results showed that the formulations with 43 μm aluminum(Al) powder particles(The particle sizes of Al powder were in the range of 2~43 μm) exhibited the optimal performance in driving flyer plates along the denotation wave propagation direction. Compared to the formulations with Al powder 13 μm, the formulations with Al powder 2 μm delivered better performance in accelerating metal flyer plates in the early stage, which, however, turned to be poor in the later stage. The CL-20-based explosives containing 25% Al far under-performed those containing 15% Al. Based on the proposed quasi-isentropic hypothesis, relevant isentropy theories, and the functional relationship between detonation parameters and entropy as well as Al reaction degree, the characteristic lines of aluminized explosives in accelerating flyer plates were theoretically studied, a quasi-isentropic theoretical model for the aluminized explosive driving the flyer plate was built and the calculation methods for the variations of flyer plate velocity, Al reaction degree, and detonation product parameters with time and axial positions were developed. The theoretical model built is verified by the experimental results of the CL-20-based aluminized explosive driving flyer plate. It was found that the model built could accurately calculate the variations of flyer plate velocity and Al reaction degree over time. In addition, how physical parameters including detonation product pressure and temperature varied with time and axial positions was identified. The action time of the positive pressure after the detonation of aluminized explosives was found prolonged and the downtrend of the temperature was slowed down and even reversed to a slight rise due to the aftereffect reaction between the Al powder and the detonation products.

A Loss-model-based Efficiency Optimization Control Method for Induction Traction System of High-speed Train under Emergency Self-propelled Mode

Increasing attention has been paid to the efficiency improvement of the induction traction system of high-speed trains due to the high demand for energy saving. In emergency self-propelled mode, however, the dc-link voltage and the traction power of the motor are significantly reduced, resulting in decreased traction efficiency due to the low load and low speed operations. Aiming to tackle this problem, a novel efficiency improved control method is introduced to the emergency mode of high-speed train traction system in this paper. In the proposed method, a total loss model of induction motor considering the behaviors of both iron and copper loss is established. An improved iterative algorithm with decreased computational burden is then introduced, resulting in a fast solving of the optimal flux reference for loss minimization at each control period. In addition, considering the parameter variation problem due to the low load and low speed operations, a parameter estimation method is integrated to improve the controller's robustness. The effectiveness of the proposed method on efficiency improvement at low voltage and low load conditions is demonstrated by simulated and experimental results.

The three-layer model of the thermohaline structure in the shallow seas

A three-layer model of the thermohaline structure is developed on the basis of the two -layer model of thermocline. The model is able to simulate the depth,thickness and intensity of both thermocline and halocline, and the temperature and salinity of both upper layer and lower layer in the shallow seas.Camparison of simulation with data is favorable.Detailed analysis is made on a variety of factors affecting the intensity of the thermocline.

A three-layer model for the thermal structure in the Huanghai Sea

A one-dimentional three-layer model for the thermal structure in the Huanghai Sea is presented in this study, me model consists of the upper mixed layer caused by heating and wind mixing, the lower mixed layer driven by tidal mixing, and the thermocline with certain thickness. The entrainment velocities of the upper and lower layers are obtained respectively. The results show that the model is capable of describing the development and decline processes of the seasonal thermocline in the Huanghai Sea, simulating successfully the Huanghai Sea Cold Water Mass, the nearshore front and surface cold water off North Jiangsu and explaining reasonably their formation mechanisms as well as the strong thermocline off Qingdao. It is suggested that the tidal mixing plays key role in the formation of the nearshore front off North Jiangsu and the strong thermocline off Qingdao. The wind mixing and the tidal mixing make the lower layer water with high nutrients go up to the upper layer. This physical process may be significant for biological plant production.

Analysis to the Driving Force Model and Drives Factor on the Utilized Changes of Cultivated Land in Qinghai Lake Area

Using path analysis, correlation analysis, partial correlation analysis and system dynamics method to study the driving force of cultivated land in Qinghai Lake Area, and using gradually regression analysis to establish the driving force model of utilized change of cultivated land. Driving factors, action mechanism and process of utilized change of cultivated land were analyzed, and the differences during all factors were compared. The study provides some decision basis for sustainable utilization and management of land resources in Qinghai Lake Area.

Nonlinear Mathematical Modeling and Sensitivity Analysis of Hydraulic Drive Unit

The previous sensitivity analysis researches are not accurate enough and also have the limited reference value, because those mathematical models are relatively simple and the change of the load and the initial displacement changes of the piston are ignored, even experiment verification is not conducted. Therefore, in view of deficiencies above, a nonlinear mathematical model is established in this paper, including dynamic characteristics of servo valve, nonlinear characteristics of pressure-flow, initial displacement of servo cylinder piston and friction nonlinearity. The transfer function block diagram is built for the hydraulic drive unit closed loop position control, as well as the state equations. Through deriving the time-varying coefficient items matrix and time-varying free items matrix of sensitivity equations respectively, the expression of sensitivity equations based on the nonlinear mathematical model are obtained. According to structure parameters of hydraulic drive unit, working parameters, fluid transmission characteristics and measured friction-velocity curves, the simulation analysis of hydraulic drive unit is completed on the MATLAB/Simulink simulation platform with the displacement step 2 mm, 5 mm and 10 mm, respectively. The simulation results indicate that the developed nonlinear mathematical model is sufficient by comparing the characteristic curves of experimental step response and simulation step response under different constant load. Then, the sensitivity function time-history curves of seventeen parameters are obtained, basing on each state vector time-history curve of step response characteristic. The maximum value of displacement variation percentage and the sum of displacement variation absolute values in the sampling time are both taken as sensitivity indexes. The sensitivity indexes values above are calculated and shown visually in histograms under different working conditions, and change rules are analyzed. Then the sensitivity indexes values of four measurable parameters, such as supply pressure, proportional gain, initial position of servo cylinder piston and load force, are verified experimentally on test platform of hydraulic drive unit, and the experimental research shows that the sensitivity analysis results obtained through simulation are approximate to the test results. This research indicates each parameter sensitivity characteristics of hydraulic drive unit, the performance-affected main parameters and secondary parameters are got under different working conditions, which will provide the theoretical foundation for the control compensation and structure optimization of hydraulic drive unit.

Modelling of a Human Driver’s Interaction with Vehicle Automated Steering Using Cooperative Game Theory

The introduction of automated driving systems raised questions about how the human driver interacts with the automated system. Non-cooperative game theory is increasingly used for modelling and understanding such interaction, while its counterpart, cooperative game theory is rarely discussed for similar applications despite it may be potentially more suitable. This paper describes the modelling of a human driver’s steering interaction with an automated steering system using cooperative game theory. The distributed Model Predictive Control approach is adopted to derive the driver’s and the automated steering system’s strategies in a Pareto equilibrium sense, namely their cooperative Pareto steering strategies. Two separate numerical studies are carried out to study the influence of strategy parameters, and the influence of strategy types on the driver’s and the automated system’s steering performance. It is found that when a driver interacts with an automated steering system using a cooperative Pareto steering strategy, the driver can improve his/her performance in following a target path through increasing his/her effort in pursuing his/her own interest under the driver-automation cooperative control goal. It is also found that a driver’s adoption of cooperative Pareto steering strategy leads to a reinforcement in the driver’s steering angle control, compared to the driver’s adoption of non-cooperative Nash strategy. This in turn enables the vehicle to return from a lane-change maneuver to straight-line driving swifter.

Two-vector Dimensionless Model Predictive Control of PMSM Drives Based on Fuzzy Decision Making

Model predictive controls(MPCs) with the merits of non-linear multi-variable control can achieve better performance than other commonly used control methods for permanent magnet synchronous motor(PMSM) drives.However,the conventional MPCs have various issues,including unsatisfactory steady-state performance,variable switching frequency,and difficult selection of appropriate weighting factors.This paper proposes two different improved MPC methods to deal with these issues.One method is the two-vector dimensionless model predictive torque control(MPTC).Two cost functions(torque and flux) and fuzzy decision-making are used to eliminate the weighting factor and select the first optimum vector.The torque cost function selects a second vector whose duty cycle is determined based on the torque error.The other method is the two-vector dimensionless model predictive current control(MPCC).The first vector is selected the same as in the conventional MPC method.Two separate current cost functions and fuzzy decision-making are used to select the second vector whose duty cycle is determined based on the current error.Both proposed methods utilize the space vector PWM modulator to regulate the switching frequency.Numerical simulation results show that the proposed methods have better steady-state and transient performances than the conventional MPCs and other existing improved MPCs.

Simulation on model predictive control for PMSM drive system based on double extended state observer

A novel double extended state observer(DESO)based on model predictive torque control(MPTC)strategy is developed for three-phase permanent magnet synchronous motor(PMSM)drive system without current sensor.In general,to achieve high-precision control,two-phase current sensors are necessary for successful implementation of MPTC.For this purpose,two ESOs are used to estimate q-axis current and stator resistance respectively,and then based on this,d-axis current is estimated.Moreover,to reduce torque and flux ripple and to improve the performance of the torque and speed,MPTC strategy is designed.The simulation results validate the feasibility and effectiveness of the proposed scheme.

Controller design based on viscoelasticity dynamics model and experiment for flexible drive unit

In order to ensure that the system has the advantage of light weight and vibration absorption, the steel rope is used as a flexible transmission part. A flexible drive unit(FDU) is developed, whose features are guided by steel rope, increasing force by the movable pulley group, modular, convenient and flexible. Dynamics model for controller is deduced based on the constitutive equation of viscoelasticity. Controller is designed for position control and is based on the viscoelasticity dynamics model compensation control strategy proposed. The control system is based on the TURBO PMAC multi-axis motion control card.Prototype loading experiments and velocity experiments results show that the FDU can reach 2 Hz with no load and the max speed of 30(°)/s. The FDU has the capability of the load torque 11.2 N·m and the speed of 24(°)/s simultaneously, and the frequency response is 1.3 Hz. The FDU can be used to be the pitch joint of hip for biped robot whose walking speed is 0.144 km/h theoretically.

Modeling of large scale solar cell handling robot with belt-driven flexible arms

To increase the competition of the solar energy collection system, the size of the solar panel module during the manufacturing process is being increased continuously. As the size of the solar panel increases, the size of the robot to handle the panel increased also. The change in scale of the robot inevitably results ill the amplification of the adverse effect of tile flexure. The main source of the flexure in the large scale solar cell panel handling system is the long and thin fork fingers of the [land and the solar cell panel. In addition, tile belt-driven actuator system used by most of the large scale panel handling robot is another significant source of the vibration. In this paper, the flexible multi body dynamic model of a large scale solar cell panel handling robot, which is being designed and constructed with the help of Kyung Hee University, is developed. The belt-driven system in the robot is also modeled as flexible system and included ill the robot to represent the actual vibration characteristics of the actuator system. C 2013 The Chinese Society of Theoretical and Applied Mechanics. [doi： 10.1063/2.1301310]

Modeling and Analysis of Pumping Motor Drives in Hardware-in-the-Loop Environment

In the proposed paper, the new experimental results are described obtained from the laboratory stand and the model developed by the authors. A method of acquiring characteristics of a pump motor drive using a hardware-in-the-loop simulation approach is explained. To explore the centrifugal pumps manufactured by ABB, their own control system is used whereas an industrial pump is replaced with the specially designed simulator. To clarify the model topology and parameters, a double-machine assembly was designed and used as universal pump prototype. A library of reference and disturbance signals used in pumping was applied as a modeling tool. In this way, the advantages of mathematical and physical simulations have been combined with optimal interaction of both approaches.

A simple analytical model of laser direct-drive thin shell target implosion

A high-neutron yield platform imploded by a thin shell target is generally built to probe nuclear science problems,and it has the advantages of high neutron yield,ultrashort fusion time,micro fusion zone,isotropic and monoenergetic neutron.Some analytical models have been proposed to interpret exploding-pusher target implosion driven by a long wavelength laser,whereas they are imperfect for a 0.35 μm laser implosion experiment.When using the 0.35 μm laser,the shell is ablated and accelerated to high implosion velocity governed by Newton’s law,ablation acceleration and quasi-adiabatic compression models are suitable to explain the implosion of a laser direct-drive thin shell target.The new analytical model scales bang time,ion temperature and neutron yield for large variations in laser power,target radius,shell thickness,and fuel pressure.The predicted results of the analytical model are in agreement with experimental data on the ShenguangIII prototype laser facility,100 kJ laser facility,Omega,and NIF,it demonstrates that the analytical model benefits the understanding of experiment performance and optimizing the target design of high neutron yield implosion.

Evaluation of Driver Distraction with Changes in Gaze Direction Based on a Vestibulo-Ocular Reflex Model

With the aim of improving parameter identification and, eventually, evaluating driver distraction with changes in gaze direction, we applied a genetic algorithm (GA) method to identify parameters for an existing vestibulo-ocular reflex (VOR) model. By changing the initial inputs to the GA and fixing two parameters pertaining to the horizontal direction, we achieved improved parameter identification with a lower mean-square error. The influence of driver distraction on eye movement with changes in gaze direction was evaluated from the difference between the predicted and observed VOR in the vertical axis. When a driver was given an additional mental workload, the mean-square error between the measured and simulated values was bigger than that in the absence of the mental workload. This confirmed the relationship between driver distraction and eye movement in the vertical direction. We hope that this method can be applied in evaluating driver distraction.

Dynamic Characteristic Study of Ball Screw Feed Drive Systems Based on Multi-flexible Body Model

A new ball screw dynamic model was developed under the adequate consideration of the interaction in the screw-nut assembly (not only the mutual-coupling factors but also the self-coupling factors) . Based on this model,the multi-flexible body (MFB)dynamic model of ball screw feed drive system was then founded in order to take full account of the influencing factor of system flexibility and study the dynamic behaviors of the whole mechanical transmissions. Moreover,the MFB based state space modeling was proposed by modal state space method, which extraced the eigenmodes of more dominant modes and applied them into an MFB state space model,and realized the integrated model of servo drives and MFB mechanical transmissions more effectively and efficiently. In conclusion,the comparisons between simulations and experimental results show: the stiffness formulation of the ball screw assembly derived above is a suitable method for achieving accurate MFB models of ball screw mechanical transmission systems,this proposed MFB model is valid,and the integrated model of ball screw feed drive system is accurate and reliable. All these provide the important approaches and guidelines for dynamic characteristic study and selection of control parameters in the machine tool design period.

Effective way of alleviating poverty against poverty control: Based on the model of "Three Drives, Four Joints" in Zhen'an County

Based on the survey research of poverty controlling model of "Three Drives, Four Joints" in Zhen'an County, its forming motives, implementing mechanism, and constraint factors have been explored to testify its enlightenment and applicability, establishing a promotable, applicable, and effective poverty alleviation model. "Three Drives, Four Joints" model is linked to the poor who lacks ability of self-development. Relying on the drives from key leading companies, the capable and the rich, a community with shared interests by the poor and the subjects of the "three drives" could be formed through "Joint Production, Joint Resources, Joint Community of Stock, and Joint Operation". The linked poverty alleviation development model of "the influential and the rich bring along the poor" and "A rich household would help the others" come into being. It is found out that the model of "Three Drives, Four Joints" is in essence a poverty alleviation method focusing on the increase of the income and diversified ways of increasing the earnings. Problems of poverty alleviation carrier and joint mechanism have been solved in the poverty alleviation process. The model is innovative in activating the resource elements, helping to move the poor out of poverty. A referential, copyable, and applicable model is offered to advance the poverty alleviation in mountainous areas in China.

Study on Modeling and Control Strategy for Electric Drive Motor of Tracked Vehicles

Aimed at the requirements for electric transmission system of a military tracked vehicle, the motor's design indexes were analysed and calculated. A model based on saturate inductance parameter of interior permanent magnet (IPM) synchronous motor was brought forward by using finite element analysis. And its control strategy based on the largest running capability was studied also. The experiment results for a scale model show that the modelling method improves the model's accuracy, and the motor's control strategy is effective.

3D Object Detection with Attention:Shell-Based Modeling

LIDAR point cloud-based 3D object detection aims to sense the surrounding environment by anchoring objects with the Bounding Box(BBox).However,under the three-dimensional space of autonomous driving scenes,the previous object detection methods,due to the pre-processing of the original LIDAR point cloud into voxels or pillars,lose the coordinate information of the original point cloud,slow detection speed,and gain inaccurate bounding box positioning.To address the issues above,this study proposes a new two-stage network structure to extract point cloud features directly by PointNet++,which effectively preserves the original point cloud coordinate information.To improve the detection accuracy,a shell-based modeling method is proposed.It roughly determines which spherical shell the coordinates belong to.Then,the results are refined to ground truth,thereby narrowing the localization range and improving the detection accuracy.To improve the recall of 3D object detection with bounding boxes,this paper designs a self-attention module for 3D object detection with a skip connection structure.Some of these features are highlighted by weighting them on the feature dimensions.After training,it makes the feature weights that are favorable for object detection get larger.Thus,the extracted features are more adapted to the object detection task.Extensive comparison experiments and ablation experiments conducted on the KITTI dataset verify the effectiveness of our proposed method in improving recall and precision.

Load Torque Compensator for Model Predictive Direct Current Control in High Power PMSM Drive Systems

The widely used cascade speed and torque controllers have a limited control performance in most high power applications due to the low switching frequency of power electronic converters and the convenience to avoid speed overshoots and oscillations for lifetime considerations. Model Predictive Direct Current Control （MPDCC） leads to an increase of torque control performance taking into account the discrete nature of inverters but temporary offsets and poor responses to load torque variations are still issues in speed control. A load torque estimator is proposed in this paper in order to further improve dynamic behavior. It compensates the load torque influence on the speed control setting a feed forward torque reference value. The benefits are twice; the speed controller reaches the speed reference value without offsets which would need to be compensated by an integrator and a better response to load torque variations is obtained since they are detected and compensated leading to small speed variations. Moreover, the influence of pararneter errors and disturbances has been analyzed and limited so that they play a minor role in operation.