Lightweight Design of Automobile Drive Shaft Based on the Characteristics of Low Amplitude Load Strengthening

There are two kinds of internationally recognized approaches in terms of lightweight design.One is based on fatigue accumulated damage theory to achieve better reliability by optimal structural design; another is to use high performance lightweight materials.The former method takes very few considerations on the structural strengthening effects caused by the massive small loads in service.In order to ensure safety,the design is usually conservative,but the strength potential of the component is not fully exerted.In the latter method,cost is the biggest obstacle to lightweight materials in automotive applications.For the purpose of light weighting design on a fuel cell vehicle,the new design method is applied on drive shafts.The method is based on the low amplitude load strengthening characteristics of the material,and allows the stress,corresponding to test load,to enter into the strengthened range of the material.Under this condition,the light weighting design should assure that the reliability of the shaft is not impaired,even maximizes the strength potential of machine part in order to achieve the weight reduction and eventually to reduce the cost.At last,the feasibility of the design is verified by means of strength analysis and modal analysis based on the CAD model of light weighted shaft.The design applies to the load case of half shaft in independent axle,also provides technological reference for the structural lightweight design of vehicles and other machineries.

Dynamic performance of angle-steel concrete columns under low cyclic loading-II:parametric study

Tests of nine angle-steel concrete column （ASCC） specimens under low cyclic loading are described in a companion paper （Zheng and Ji, 2008）. In this paper, the skeleton curves from the numerical simulation are presented, and show good agreement with the test results. Furthermore, parametric studies are conducted to explore the influence of factors such as the axial compression ratio, shear steel plate ratio, steel ratio, prismatic concrete compression strength, yield strength of angle steel and shear span ratio, etc., on the monotonic load-displacement curves of the ASCCs. Based on a statistical analysis of the calculated results, hysteretic models for load-displacement and moment-curvature are proposed, which agree well with the test results. Finally, some suggestions concerning the conformation of ASCCs are proposed, which could be useful in engineering practice.

Deformation properties of chloride saline soil under action of a low-temperature environment and different loads

To find the deformation properties of chloride saline soil under the influence of a low temperature environment and different loads,two types of chloride saline soil were selected and their deformation process was tested in the laboratory and analyzed during the cooling process in the sensitive cryogenic temperature range.The research results show that high-chloride-salt saline soil underwent little volume change under the no-load condition during the cooling process.Under staticload and dynamic-load conditions,different degrees of settlement deformation occurred;throughout the entire cooling process,another chloride saline soil with a high proportion of sulfate salt underwent volume expansion under no-load and static-load conditions.Under the no-load condition,a certain degree of settlement deformation occurred.Deformation properties were evaluated at different time points during the cooling process for two kinds of chloride saline soil.Finally,deformation characteristics of chloride saline soil were analyzed from the perspective of salt type and crystallization variation under the action of a low-temperature environment and different loads.

Effects of time lag and stress loading rate on permeability in low permeability reservoirs

In order to study the effect of time lag and stress loading rates on rock deformation,the conventional stepped stress loading mode was changed into a continuous mode to investigate the effect of effective pressure on permeability and porosity.The time lag effect of rock deformation illustrating the relationship between changes in permeability and steady time was studied.Permeability reduction ratios were measured under different stress loading rates which were achieved by different pump rate settings.The results show that permeability and porosity gradually decrease with increases in effective pressure.Permeability at high effective pressure attains stability quickly.Steady times at low effective pressure are very long.Reduction in permeability at lower stress loading rates is small,while,in contrast,it is large at high stress loading rates.

Four-week pegylated interferon a-2a monotherapy for chronic hepatitis C with genotype 2 and low viral load:A pilot,randomized study

AIM:To assess the efficacy and advantages of 4-wk pegylated interferon a-2a(peg-IFN-a2a) monotherapy for chronic hepatitis C patients with strong predictors of sustained virologic response(SVR).METHODS:Patients(n = 33) with genotype 2 and low viral load(< 100 KIU/mL),who became HCV RNA negative after 1 wk of IFN treatment,were randomly allocated to receive a 4-or 12-wk treatment course at a ratio of 2:1,respectively,with a subsequent 24-wk follow-up period.Peg-IFN-a2a was administered subcutaneously at a dose of 180 μg or 90 μg once weekly.SVR was defined as absence of serum HCV RNA at the end of the follow-up period.RESULTS:All patients completed the treatment schedule,and more than half were symptom-free during the treatment.In the 4-wk treatment group,20 of 22(91%) patients achieved SVR.Two patients relapsed,but achieved SVR following re-treatment with peg-IFN-a2a alone.In the 12-wk treatment group,11 of 11(100%) patients attained SVR.CONCLUSION:Our results show that a 4-wk course of peg-IFN-a2a monotherapy can achieve a high SVR rate in "IFN-sensitive" patients,without negatively affecting outcome.

Three-Phase Unbalance Prediction of Electric Power Based on Hierarchical Temporal Memory

The difference in electricity and power usage time leads to an unbalanced current among the three phases in the power grid.The three-phase unbalanced is closely related to power planning and load distribution.When the unbalance occurs,the safe operation of the electrical equipment will be seriously jeopardized.This paper proposes a Hierarchical Temporal Memory(HTM)-based three-phase unbalance prediction model consisted by the encoder for binary coding,the spatial pooler for frequency pattern learning,the temporal pooler for pattern sequence learning,and the sparse distributed representations classifier for unbalance prediction.Following the feasibility of spatial-temporal streaming data analysis,we adopted this brain-liked neural network to a real-time prediction for power load.We applied the model in five cities(Tangshan,Langfang,Qinhuangdao,Chengde,Zhangjiakou)of north China.We experimented with the proposed model and Long Short-term Memory(LSTM)model and analyzed the predict results and real currents.The results show that the predictions conform to the reality;compared to LSTM,the HTM-based prediction model shows enhanced accuracy and stability.The prediction model could serve for the overload warning and the load planning to provide high-quality power grid operation.

CoNi nanoparticles anchored inside carbon nanotube networks by transient heating:Low loading and high activity for oxygen reduction and evolution

Transitional metal alloy and compounds have been developed as the low cost and efficient bifunctional electrocatalysts for oxygen reduction reaction(ORR)and oxygen evolution reaction(OER).However,a high mass loading of these catalysts is commonly needed to achieve acceptable catalytic performance,which could cause such problems as battery weight gain,mass transport blocking,and catalyst loss.We report herein the preparation of fine CoNi nanoparticles(5-6 nm)anchored inside a nitrogendoped defective carbon nanotube network(CoNi@N-DCNT)by a transient Joule heating method.When utilized as an electrocatalyst for oxygen reduction and evolution in alkaline media,the CoNi@N-DCNT film catalyst with a very low mass loading of 0.06 mg cm^(-2) showed excellent bifunctional catalytic performance.For ORR,the onset potential(Eonset)and the half-wave potential(E_(1/2))were 0.92 V versus reversible hydrogen electrode(vs.RHE)and 0.83 V(vs.RHE),respectively.For OER,the potential at the current density(J)of 10 mA cm^(-2)(E_(10))was 1.53 V,resulting in an overpotential of 300 mV much lower than that of the commercial RuO_(2) catalyst(320 mV).The potential gap between E_(1/2) and E_(10) was as small as 0.7 V.Considering the low mass loading,the mass activity at E_(10) reached at 123.2 A g^(-1),much larger than that of the RuO_(2) catalyst and literature results of transitional metal-based bifunctional catalysts.Moreover,the CoNi@N-DCNT film catalyst showed very good long-term stability during the ORR and OER test.The excellent bifunctional catalytic performance could be attributed to the synergistic effect of the bimetal alloy.

1.0 V low voltage CMOS mixer based on voltage control load technique

A CMOS active mixer based on voltage control load technique which can operate at 1.0 V supply voltage was proposed, and its operation principle, noise and linearity analysis were also presented. Contrary to the conventional Gilbert-type mixer which is based on RF current-commutating, the load impedance in this proposed mixer is controlled by the LO signal, and it has only two stacked transistors at each branch which is suitable for low voltage applications. The mixer was designed and fabricated in 0.18 tam CMOS process for 2.4 GHz ISM band applications. With an input of 2.44 GHz RF signal and 2.442 GHz LO signal, the measurement specifications of the proposed mixer are： the conversion gain （Gc） is 5.3 dB, the input-referred third-order intercept point （PIIP3） is 4.6 dBm, the input-referred 1 dB compression point （P1dB） is --7.4 dBm, and the single-sideband noise figure （NFSSB） is 21.7 dB.

Platinum nanoparticles coated by graphene layers: A low-metal loading catalyst for methanol oxidation in alkaline media

Platinum catalysts play a major role in the large scale commercialization of direct methanol fuel cells(DMFC).Here,we present a procedure to create a nanostructural graphene-platinum(Gr Pt)composite containing a small amount(5.3 wt%)of platinum nanoparticles coated with at least four layers of graphene.The composite,as Gr Pt ink,was deposited on a glassy carbon electrode and its electrocatalytic activity in a methanol oxidation reaction(MOR)was evaluated in a 1 M CH3OH/1 M NaOH solution.The results indicated an enhanced catalytic performance of GrPt towards MOR in alkaline media compared with the Pt/C material.Electron energy-loss spectroscopy and X-ray photoelectron spectroscopy(recorded before and after the electrochemical assays)were employed to analyze the changes in the chemical composition of the nanomaterial and to explain the transformations that took place at the electrode surface.Our findings suggest that growing of graphene on platinum nanoparticles improve the catalytic performance of platinum-graphene composites towards MOR in alkaline media.

Process Adaption of a Small WWTP Operated at Low Loading Conditions for Substantial Energy Savings

The very long tradition of the activated sludge treatment model within the water industry has demonstrated very versatile possibilities to adopt the operation mode for different enhancements. By looking into other treatment models within the activated sludge family it is possible to find alternatives for the operation. This paper concentrates on the possibilities to improve even small WWTP with respect to energy savings. The small plant in Northern Sweden, called Rosvik WWTP, is given as an example. Some important findings related to the intermittent aeration mode may be summarized as follows: 1) An energy savings for the operation of the small WWTP with respect to aeration needs that resulted in a decrease of the energy power supply by more than 35%, as compared with the previous operation based on continuous aeration;2) The up to date effluent levels with respect to the main pollutants have remained at very good levels in 2020, P-level averages 0.16 mg P/l versus consent level < 0.5 mg P/l;COD-level 40 versus < 70 mg/l and BOD7 9 versus < 15 mg/l;3) Sometimes, also improved sludge settling characteristics have been observed, thus providing improved discharge figures;4) The potential to develop an enhanced biological phosphorus removal. There are however some needed conditions to accomplish these improvements: 1) Reliable on-line probes for both oxygen control, SS-concentration control and optionally also for nitrogen control;2) A flexible automation system that allows the needed process modifications to take place;3) And finally, very important dedicated and competent plant operators, with the needed curiosity for operation improvements.

Effect of Mild-calcined Coal Gangue Additionon Hot Strength and Refractoriness Under Loadof Ultra Low Cement Castablesin Al_2O_3-SiO_2 System

This work explored the way to improve hot modulus q/＇ rupture （HMOR） and refractoriness under load （RUL） by adding mild-calcined coal gangue （MCG） in Al2O3 -SiO2 ultra low cement （ULC） castables, making use of the in-situ effect of the MCG during heating-up. The influence of respective additions of 5%, 10% and 1.5% of the MCG powders calcined at 700℃ was investigated on HMOR at 1400 ℃ and RUL of the castables. With increased addition of the MCG, HMOR and RUL become significantly enhanced. At 10% of the MCG addition, HMOR reaches 3 MPa, as compared to 0. 3 MPa in the case of no MCG addition. RUL of the specimens dried at 110 ℃for 24 h can be increased by some 270 ℃ with 10% of the MCG addition. RUL 0.11 the specimens preheated at 1 500℃ for 3 h maintains the growth trend with the MCG addition increasing. The microstructure of the heated castable samples was investigated by means of SEM. The in-situ formed needle-like and interlaced mullite in the matrix is contributive to the tmprovement.

The Control Technology Research of the Z-source Three-phase Four-bridge Arm Inverter

Z-source inverter can boost the voltage of the DC-side, allow the two switches of the same bridge arm conducting at the same time and it has some other advantages. The zero-sequence current flows through the fourth leg of the three-phase four-leg inverter so the three-phase four-leg inverter can work with unbalanced load. This paper presents a Z-source three-phase four-leg inverter which combines a Z-source network with three-phase four-leg inverter. The circuit uses simple SPWM modulation technique and the fourth bridge arm uses fully compensated control method. The inverter can maintain a symmetrical output voltage when the proposed scheme under the unbalanced load.

High microwave absorption performances for single-walled carbon nanotube–epoxy composites with ultra-low loadings

Microwave-absorbing polymeric composites based on single-walled carbon nanotubes （SWNTs） are fabricated via a simple yet versatile method, and these SWNT-epoxy composites exhibit very impressive microwave absorption perfor- mances in a range of 2 GHz-18 GHz. For instance, a maximum absorbing value as high as 28 dB can be achieved for each of these SWNT-epoxy composites （1.3-mm thickness） with only 1 wt% loading of SWNTs, and about 4.8 GHz bandwidth, corresponding to a microwave absorption performance higher than 10 dB, is obtained. Furthermore, such low and appro- priate loadings of SWNTs also enhance the mechanical strength of the composite. It is suggested that these remarkable results are mainly attributable to the excellent intrinsic properties of SWNTs and their homogeneous dispersion state in the polymer matrix.

Ballistic Properties of Some Low Solid Loading Butalites Formulations

The ballistic properties of a low solid loading composite solid propellant family （Butalites） was studied experimentally by using propellant formulations based on hydroxy-terminated polybutadiene pre-polymer （HTPB） as fuel binder main backbone, mono and bi-modal system ammonium perchlorate oxidizer （AP）, copper chromite （CC） as burning rate accelerator and aluminum powder （A1） as metallic fuel. Higher pressures and AP contents as well as smaller AP particle size were found to increase burning rate. The same behavior verified with AI and CC addition. A significant increase of burning rate was recorded when CC added to the aluminized formulations compared with the non-aluminized of the same oxidizer solid loading and particle size.

Process Adaption and Modifications of a Nutrient Removing Wastewater Treatment Plant in Sri Lanka Operated at Low Loading Conditions

The Sri Lankan national water authority, that is The National Water Supply and Drainage Board (NWS&DB) has taken a new wastewater treatment plant into operation at Ja Ela, North of Colombo. The plant has been in operation since September 2011. In April 2012, it was concluded how a test of the aeration efficiency and a performance test should be carried out. The tests have been based on the actual loading of the plant and the analysis results from the daily process control. The evaluation of the aeration efficiency is not reported in this paper. The paper presents the overall performance of the water treatment part of the plant during start-up conditions, from fall 2011 through the first five months of 2012. The results from the operation are found in Table 1. An important circumstance at the plant is the current very low loading in comparison with the design load. This fact has resulted in an introduction of an intermittent mode of the aeration (nitrification) reactor. Based on operation figures, during more than a month (May 2012), it has been possible to give a realistic assessment of the overall performance. The most striking results are summarized as follows: 1) The intermittent operation has enabled an energy efficient operation of the plant. By the introduction of the intermittent aeration, the energy consumption has been reduced by around 75%, compared with the continuous operation mode;2) The plant performance during the intermittent operation has been improved with respect to virtually all important pollution variables. The most striking improvement is the discharge total P level, reflecting that a substantial enhanced biological phosphorus removal takes. The typical discharge levels found during May 2012, were compared with the earlier obtained values. It is important to underline that the loading on the plant has slightly increased during May as compared with the previous operation period.

Punching and Local Damages of Fiber and FRP Reinforced Concrete under Low-Velocity Impact Load

In recent years, the development and application of high performance fiber reinforced concrete or cementitious composites are increasing due to their high ductility and energy absorption characteristics. However, it is difficult to obtain the required properties of the FRCC by simply adding fiber to the concrete matrix. Many researchers are paying attention to fiber reinforced polymers (FRP) for the reinforcement of construction structures because of their significant advantages over high strain rates. However, the actual FRP products are skill-dependent, and the quality may not be uniform. Therefore, in this study, two-way punching tests were carried out to evaluate the performances of FRP strengthened and steel and polyvinyl alcohol (PVA) fiber reinforced concrete specimens for impact and static loads. The FRP reinforced normal concrete (NC), steel fiber reinforced concrete (SFRC), and PVA FRCC specimens showed twice the amount of enhanced dissipated energy (total energy) under impact loadings than the non-retrofitted specimens. In the low-velocity impact test of the two-way NC specimens strengthened by FRPs, the total dissipated energy increased by 4 to 5 times greater than the plain NC series. For the two-way specimens, the total energy increased by 217% between the non-retrofitted SFRC and NC specimens. The total dissipated energy of the CFRP retrofitted SFRC was twice greater than that of the plain SFRC series. The PVA FRCC specimens showed 4 times greater dissipated energy than for the energy of the plain NC specimens. For the penetration of two-way specimens with fibers, the Hughes formula considering the tensile strength of concrete was a better predictor than other empirical formulae.

基于Load重用的低功耗数据Cache设计

针对嵌入式处理器中数据Cache功耗显著的特点,提出了一种基于Load重用的低功耗数据Cache设计方法.通过保存Load指令从数据Cache中取回的数据,实现了随后Load指令对该数据的重新使用,从而减少了数据Cache的访问次数,有效降低了数据Cache的功耗.在SuperV_EF01DSP上的实验结果显示,采用该方法后,在处理器性能没有损失的情况下,数据Cache功耗平均降低29.48%,面积仅增加0.64%.

Low-e玻璃对空调负荷及建筑能耗的影响

分别根据6种传热系数和遮阳系数不同的窗玻璃对2栋建筑进行空调负荷和能耗模拟计算,结果表明,在深圳市,对空调负荷以及全年能耗影响最大的是玻璃的遮阳系数,其次是传热系数,Low-e中空玻璃与普通3mm白玻璃相比,空调负荷可以降低20%左右,全年空调能耗降低24%左右;在北京市,使用Low-e玻璃可以降低32%的空调能耗和20%的空调负荷,但是却增加了2%的供暖能耗。

低负荷血流限制和高强度抗阻运动对男性运动青年大腿微循环功能的影响

背景:微循环作为人体物质能量代谢交换的唯一场所,与人体运动能力密切相关。抗阻运动是提高微循环功能的有效方式,但也有研究指出血流限制训练也能提高微循环功能,且具有负荷小和安全性高等优点。目的:比较6周低负荷血流限制运动、高强度抗阻运动对运动型男性青年大腿微循环功能的影响,并从血管内皮功能角度探讨运动改善微循环功能的可能机制。方法:将湖北民族大学60名体育专业男性大学生按照随机数表法分为对照组、高强度抗阻运动组和低负荷血流限制运动组,每组20人。低负荷血流限制运动组进行6周(每周3次、每次90 min、运动强度为30%1RM)的低负荷血流限制运动;高强度抗阻运动组进行6周(每周3次、每次90 min、运动强度为70%1RM强度)的抗阻训练;对照组该时间段不进行任何形式的运动训练。分别在干预开始的前1 d以及6周干预结束后次日的晨起空腹状态下对3组受试者微血管血流灌注量、经皮氧分压、肌氧饱和度、一氧化氮、内皮型一氧化氮合酶、内皮素1、血管内皮细胞生长因子及大腿围、肌力等指标进行测试。结果与结论:①运动干预后,低负荷血流限制运动组和高强度抗阻运动组的微血管血流灌注量加热值、血细胞移动速度加热值与对照组及运动干预前相比有显著差异(P<0.05);低负荷血流限制运动组微血管血流灌注量加热值、血细胞移动速度加热值与高强度抗阻运动组相比有显著差异(P<0.05);经皮氧分压和肌氧饱和度与干预前相比有显著性差异(P<0.05)。②运动干预后,低负荷血流限制运动组和高强度抗阻运动组一氧化氮、内皮型一氧化氮合酶、内皮素1、血管内皮细胞生长因子与对照组及运动干预前相比有显著差异(P<0.05)。③运动干预后,低负荷血流限制运动组和高强度抗阻运动组大腿围和大腿肌肉力量与运动干预前相比有显著差异(P<0.05)。④上述结果证实,6周低负荷血流限制运动和高强度抗阻运动可能通过调节内皮型一氧化氮合酶、内皮素1、血管内皮细胞生长因子等血管因子的分泌,提高体育专业大学生大腿微循环功能,并增加大腿肌肉的收缩力量,且低负荷血流限制运动对微血管血流灌注量、血细胞移动速度的干预效果更佳,因此低负荷血流限制运动较高强度抗阻运动在提高微循环功能方面更具优势。

Experimental study of the mechanism of nanofluid in enhancing the oil recovery in low permeability reservoirs using microfluidics

Due to the low porosity and low permeability in unconventional reservoirs,a large amount of crude oil is trapped in micro-to nano-sized pores and throats,which leads to low oil recovery.Nanofluids have great potential to enhance oil recovery(EOR)in low permeability reservoirs.In this work,the regulating ability of a nanofluid at the oil/water/solid three-phase interface was explored.The results indicated that the nanofluid reduced the oil/water interfacial tension by two orders of magnitude,and the expansion modulus of oil/water interface was increased by 77% at equilibrium.In addition,the solid surface roughness was reduced by 50%,and the three-phase contact angle dropped from 135(oil-wet)to 48(water-wet).Combining the displacement experiments using a 2.5D reservoir micromodel and a microchannel model,the remaining oil mobilization and migration processes in micro-to nano-scale pores and throats were visualized.It was found that the nanofluid dispersed the remaining oil into small oil droplets and displaced them via multiple mechanisms in porous media.Moreover,the high strength interface film formed by the nanofluid inhibited the coalescence of oil droplets and improved the flowing ability.These results help to understand the EOR mechanisms of nanofluids in low permeability reservoirs from a visual perspective.