Stability analysis of longwall top-coal caving face in extra-thick coal seams based on an innovative numerical hydraulic support model

The relationship between support and surrounding rock is of great significance to the control of surrounding rock in mining process.In view of the fact that most of the existing numerical simulation methods construct virtual elements and stress servo control to approximately replace the hydraulic support problem,this paper establishes a new numerical model of hydraulic support with the same working characteristics as the actual hydraulic support by integrating numerical simulation software Rhino,Griddle and FLAC3D,which can realize the simulation of different working conditions.Based on this model,the influence mechanism of the supporting strength of hydraulic support on surrounding rock stress regulation and coal stability in front of the top coal caving face in extra thick coal seam were researched.Firstly,under different support intensity,the abutment pressure of the bearing coal and the coal in front of it presents the “three-stage”evolution characteristics.The influence range of support intensity is 15%–30%.Secondly,1.5 MPa is the upper limit of impact that the support strength can have on the front coal failure area.Thirdly,within a displacement range of 2.76 m from the coal wall,a support strength of1.5 MPa provides optimal control of the horizontal displacement of the coal.

Effects of caving–mining ratio on the coal and waste rocks gangue flows and the amount of cyclically caved coal in fully mechanized mining of super-thick coal seams

Aimed at determining the appropriate caving–mining ratio for fully mechanized mining of 20 m thick coal seam, this research investigated the effects of caving–mining ratio on the flow fields of coal and waste rocks, amount of cyclically caved coal and top coal loss by means of numerical modeling. The research was based on the geological conditions of panel 8102 in Tashan coal mine. The results indicated the loose coal and waste rocks formed an elliptical zone around the drawpoint. The ellipse enlarged with decreasing caving–mining ratio. And its long axis inclined to the gob gradually became vertical and facilitating the caving and recovery of top coal. The top coal loss showed a cyclical variation; and the loss cycle was shortened with the decreasing in caving–mining ratio. Moreover, the mean squared error(MSE) of the amount of cyclically caved coal went up with increasing caving–mining ratio, indicating a growing imbalance of amount of cyclically caved coal, which could impede the coordinated mining and caving operations. Finally it was found that a caving–mining ratio of 1:2.51 should be reasonable for the conditions.

A review of cavability evaluation in longwall top coal caving

Longwall Top Coal Caving has been considered as one of the most effective technologies for the extraction of underground thick coal seams. A large number of studies on the applicability of Longwall Top Coal Caving into new mine sites have linked the success of its application to the geo mechanical understanding of the cavability of the top coal. The paper aims to improve the knowledge of the top coal cavability evaluation. A range of parameters that affect the top coal cavability were first identified. Afterward, a number of cavability assessment methods and classifications were reviewed. The result is important in that it assists researchers in developing an advanced and reliable tool for the top coal cavability evaluation.

Structure and deformation measurements of shallow overburden during top coal caving longwall mining

Mining induced pressures are strong and overburden failure areas are large in top coal caving longwall mining, which constrains high production and safety mining. By employing the combination of the full view borehole photography technique and the seismic CT scanner technique, the deformation and failure of overlying strata of fully mechanized caving face in shallow coal seam were studied and the failure development of overburden was determined. Results show that the full view borehole photography can reveal the characteristics of strata, and the seismic CT scanner can reflect the characteristics of strata between the boreholes. The combined measurement technique can effectively determine the height of fractured and caved zones. The top end of the caved zone in Yangwangou coal mine employing the top coal caving longwall mining was at the depth of 171 m and fractured zone was at the depth of 106-110 m. The results provide a theoretic foundation for controlling the overburden strata in the shallow buried top coal caving panel.

Key technologies and equipment for a fully mechanized top-coal caving operation with a large mining height at ultra-thick coal seams

Thick and ultra-thick coal seams are main coal seams for high production rate and high efficiency in Chinese coal mines, which accounts for 44 % of the total minable coal reserve. A fully mechanized top-coal caving mining method is a main underground coal extraction method for ultra-thick coal seams. The coal extraction technologies for coal seams less than 14 m thick were extensively used in China. However, for coal seams with thickness greater than 14 m, there have been no reported cases in the world for underground mechanical extraction with safe performance, high efficiency and high coal recovery ratio. To deal with this case, China Coal Technology ＆ Engineering Group, Datong Coal Mine Group, and other 15 organizations in China launched a fundamental and big project to develop coal mining technologies and equipment for coal seams with thicknesses greater than 14 m. After the completion of the project, a coal extraction method was developed for top-coal caving with a large mining height, as well as a ground control theory for ultra-thick coal seams. In addition, the mining technology for top-coal caving with a large mining height, the ground support technology for roadway in coal seams with a large cross-section, and the prevention and control technology for gas and fire hazards were developed and applied. Furthermore, a hydraulic support with a mining height of 5.2 m, a shearer with high reliability, and auxiliary equipment were developed and manufactured. Practical implication on the technologies and equipment developed was successfully completed at the No. 8105 coal face in the Tashan coal mine, Datong, China. The major achievements of the project are summarized as follows： 1. A top-coal caving method for ultra-thick coal seams is proposed with a cutting height of 5 m and a top-coal caving height of 15 m. A structural mechanical model of overlying strata called cantilever beam-articulated rock beam is established. Based on the model, the load resistance of the hydraulic support with a large mining height for top-coal caving method is determined. With the analysis, the movement characteristics of the top coal and above strata are evaluated during top-coal caving operation at the coal face with a large mining height. Furthermore, there is successful development of comprehensive technologies for preventing and controlling spalling of the coal wall, and the top-coal caving technology with high efficiency and high recovery at the top-coal caving face with a large mining height. This means that the technologies developed have overcome the difficulties in strata control, top-coal caving with high efficiency and high coal recovery, and enabled to achieve a production rate of more than 10 Mtpa at a single top-coal caving face with a large mining height in ultra-thick coal seams; 2. A hydraulic support with 5.2 m supporting height and anti-rockburst capacity, a shearer with high reliability, a scraper conveyor with a large power at the back of face, and a large load and long distance headgate belt conveyor have been successfully developed for a top-coal caving face with large mining height. The study has developed the key technologies for improving the reliability of equipment at the coal face and has overcome the challenges in equipping the top-coal caving face with a large mining height in ultra-thick coal seams; 3. The deformation characteristics of a large cross-section roadway in ultra-thick coal seams are discovered. Based on the findings above, a series of bolt materials with a high yielding strength of 500-830 MPa and a high extension ratio, and cable bolt material with a 1 × 19 structure, large tonnage and high extension ratio are developed. In addition, in order to achieve a safe roadway and a fast face advance, installation equipment for high pre-tension bolt is developed to solve the problems with the support of roadway in coal seams for top-coal caving operation with a large mining height; 4. The characteristics of gas distribution and uneven emission at top-coal caving face with large mining height in ultra-thick coal seams are evaluated. With the application of the technologies of gas drainage in the roof, the difficulties in gas control for high intensive top-coal caving mining operations, known as ＂low gas content, high gas emission＂, are solved. In addition, large flow-rate underground mobile equipment for making nitrogen are developed to solve the problems with fire prevention and safe mining at a top-coal caving face with large mining height and production rate of more than 10 Mtpa. A case study to apply the developed technologies has been conducted at the No. 8105 face, the Tashan coal mine in Datong, China. The case study demonstrates that the three units of equipment, i.e., the support, shearer and scraper conveyor, are rationally equipped. Average equipment usage at the coal face is 92.1%. The coal recovery ratio at the coal face is up to 88.9 %. In 2011, the coal production at the No. 8105 face reached 10.849 Mtpa, exceeding the target of 10 Mtpa for a topcoal caving operation with large mining height performed by Chinese-made mining equipment. The technologies and equipment developed provide a way for extracting ultra-thick coal seams. Currently, the technologies and equipment are used in 13 mining areas in China including Datong, Pingshuo, Shendong and Xinjiang. With the exploitation of coal resources in Western China, there is great potential for the application of the technologies and equipment developed.

Simulation of recovery of upper remnant coal pillar while mining the ultra-close lower panel using longwall top coal caving

With the depletion of easily minable coal seams,less favorable reserves under adverse conditions have to be mined out to meet the market demand.Due to some historical reasons,large amount of remnant coal was left unrecovered.One such case history occurred with the remnant rectangular stripe coal pillars using partial extraction method at Guandi Mine,Shanxi Province,China.The challenge that the coal mine was facing was that there is an ultra-close coal seam right under it with an only 0.8–1.5 m sandstone dirt band in between.The simulation study was carried out to investigate the simultaneous recovery of upper remnant coal pillars while mining the ultra-close lower panel using longwall top coal caving(LTCC).The remnant coal pillar was induced to cave in as top coal in LTCC system.Physical modelling shows that the coal pillars are the abutments of the stress arch structure formed within the overburden strata.The stability of overhanging roof strata highly depends on the stability of the remnant coal pillars.And the gob development(roof strata cave-in)is intermittent with the cave-in of these coal pillars and the sandstone dirt band.FLAC3D numerical modelling shows that the multi-seam interaction has a significant influence on mining-induced stress environment for mining of lower panels.The pattern of the stress evolution on the coal pillars with the advance of the lower working face was found.It is demonstrated that the stress relief of a remnant coal pillar enhances the caveability of the pillars and sandstone dirt band below.

Technical parameters of drawing and coal-gangue field movements of a fully mechanized large mining height top coal caving working face

Under fully mechanized, large mining height top coal caving conditions, the shield beam slope angle of the support increases due to the enlargement of the top coal breaking and caving space. This results in a change of the caving window location and dimensions and, therefore, the granular coal-gangue movement and flows provide new characteristics during top coal caving. The main inferences we draw are as follows. Firstly, after shifting the supports, the caved top coal layer line and the coal gangue boundary line become steeper and are clearly larger than those under common mining heights. Secondly, during the top coal caving procedure, the speed of the coal-gangue flow increases and at the same drawing interval, the distance between the coal-gangue boundary line and the top beam end is reduced. Thirdly, affected by the drawing ratio, the slope angle of the shield beam and the dimensions of the caving window, it is easy to mix the gangue. A rational drawing interval will cause the coal-gangue boundary line to be slightly behind the down tail boom lower boundary. This rational drawing interval under conditions of large mining heights has been analyzed and determined.

Top coal caving mining technique in thick coal seam beneath the earth dam

It is important to study the mining technology under structures for raising the coal resources recovery ratio. Based on the geological and mining conditions, the top coal caving harmonic mining technique in thick coal seam beneath the earth dam was put forward and studied. The 5 factors such as the panel mining direction, panel size, panel location, panel mining sequence and panel advance velocity were taken into account in this technique. The dam movement and deformation were predicted after the thick coal seam mining and the effects of mining on the dam were studied. By setting up the surveying stations on the dam, the movement and deformation of the dam were observed during mining. By taking some protective measures on the dam, the top coal caving mining technique in thick coal seam beneath the earth dam was carried out successfully. The study demonstrates that harmonic mining in thick coal seam is feasible under the dam. The safety of the earth dam after mining was ensured and the coal resources recovery ratio was improved.

Theoretical description of drawing body shape in an inclined seam with longwall top coal caving mining

Understanding the characteristics of drawing body shape is essential for optimization of drawing parameters in longwall top coal caving mining.In this study,both physical experiments and theoretical analysis are employed to investigate these characteristics and derive a theoretical equation for the drawing body shape along the working face in an inclined seam.By analyzing the initial positions of drawn marked particles,the characteristics of the drawing body shape for different seam dip angles are obtained.It is shown that the drawing body of the top coal exhibits a shape-difference and volume-symmetry characteristic,on taking a vertical line through the center of support opening as the axis of symmetry,the shapes of the drawing body on the two sides of this axis are clearly different,but their volumes are equal.By establishing theoretical models of the drawing body in the initial drawing stage and the normal drawing stage,a theoretical equation for the drawing body in an inclined seam is proposed,which can accurately describe the characteristics of the drawing body shape.The shape characteristics and volume symmetry of the drawing body are further analyzed by comparing the results of theoretical calculations and numerical simulations.It is shown that one side of the drawing body is divided into two parts by an inflection point,with the lower part being a variation development area.This variation development area increases gradually with increasing seam dip angle,resulting in an asymmetry of the drawing body shape.However,the volume symmetry coefficient fluctuates around 1 for all values of the seam dip angle variation,and the volumes of the drawing body on the two sides are more or less equal as the variation development volume is more or less equal to the cut volume.Both theoretical calculations and numerical simulations confirm that the drawing body of the top coal exhibits the shape-difference and volume-symmetry characteristic.

Drawing mechanisms for top coal in longwall top coal caving(LTCC):A review of two decades of literature

This review details the state of the art in research on top coal drawing mechanisms in Longwall top coal caving(LTCC)by examining the relevant literature over the last two decades.It startswith an introduction of the brief history and basic procedures of LTCC.The framework of research on the drawing mechanism,basic concepts,and some theoretical models of LTCC are detailed in sect.research framework of top coal drawingmechanism.The authors note that theTop coal drawbody(TCD),Top coal boundary(TCB)and Top coal recovery ratio(TCRR)are key factors in the drawingmechanism.TheBody-boundary-ratio(BBR)research system has been the classic framework for research over the last 20 years.The modified Bergmark-Roos model,which considers the effects of the supporting rear canopy,flowing velocity of top coal,and its shape factor,is optimal for characterizing the TCD.A 3Dmodel to describe the TCB that considers the thicknesses of the coal seam and roof strata is reviewed.In sect.physical testing and numerical simulation,the physical tests and numerical simulations in the literature are classified for ease of bibliographical review,and classic conclusions regarding the drawing mechanism of top coal are presented and discussedwith elaborate illustrations and descriptions.The deflection of the TCDis noted,and is caused by the shape of the rear canopy.The inclined coal seam always induces a largerTCD,and a deflection in theTCDhas also been observed in it.The effects of the drawing sequence and drawing interval on the TCRR are reviewed,where a long drawing interval is found to lead to significant loss of top coal.Its flowing behavior and velocity distribution are also presented.Sect.practical applications of drawingmechanisms forLTCCmines 4 summarizes over 10 cases where the TCRRof LTCCmines improved due to the guidance of the drawing mechanism.The final section provides a summary of the work here and some open questions.Prospective investigations are highlighted to give researchers guidance on promising issues in future research on LTCC.

Analysis and key control technologies to prevent spontaneous coal combustion occurring at a fully mechanized caving face with large obliquity in deep mines

In order to prevent spontaneous coal combustion occurring at a fully mechanized caving face with large obliquity in deep mines in China, we have analyzed the characteristics of spontaneous coal combustion and explain theoretically the factors affecting spontaneous coal combustion, such as rock bursts, high temperatures, high ventilation resistance, slow advancing speed and large obliquity mining. Key technologies to prevent spontaneous combustion occurring in sharply inclined seams in deep mines are pro- posed; these include pouring water, stopping leakage in upper and lower comers of the working face, choking off the goaf and cov- eting the coal. CO concentrations were controlled within two years to less than 15×10^-6 at the upper comer by applying these tech- nologies at the 1410 working face of the Huafeng coal mine. Our method has significant theoretical value and is of practical impor- tance in controlling spontaneous coal combustion occurring at a fully mechanized caving face with large obliquity in deep mines.

Investigation on the stress field characteristic of top coal at FMTC faces under the influence of caving thickness

In the background of the technology condition and the geological condition of the 1151（3） fully mechanized top-coal caving face （FMTC face）, and by means of taking nonlinear 3D numerical simulation, the stress redistribution rules of top coal with different thick coal seam were obtained by investigation on the numerical simulation of the redistributions of the stress with different coal seam＇s thickness. The research showes that there exists a certain difference on the stress distributions of the top coal at face, the maximum principal stress is located near to the tailentry＇s corner. The vertical stress＇s peak of the top coal decreases and the distance ahead of face position increases as the once mining thickness of the coal seam increases. At the same coal seam, the vertical stresses＇ peak of top coal gradually decreases from the top to the bottom, the peak＇s position is basically the same and its changes are gradually obvious with the thickness of coal seam increas- ing. The vertical stress of top coal places in a low stress state at a certain range ahead of face and over the face, which reveals the essence that the support loads are generally low under the condition of FMTC. The study supplies the theoretical foundation for the support design and selection, the theory of top coal＇s fragmentation, the movement rules of top coal and improving the recovery of top coal.

Development of 3D top coal caving angle model for fully mechanized extra-thick coal seam mining

During high-intensity,fully mechanized mining of extra-thick coal seam,the top coal would cave to a certain 3D form.Based on the data collected during drilling,a 3D model of top coal caving surface space was established to determine the relationship between the location of the stope roof and the caving surface,enabling the mathematical computation of the top caving angle(φ).The drilling method was employed to measure the top caving angle on two extra-thick fully mechanized coal caving faces under the conditions of three geological structures,namely,no geological structure,igneous rock structure,and fault structure.The results show that the value of top caving angle could be accurately estimated on-site with the 9-parameter 3D top coal caving surface model built with the drilling method.This method is a novel on-site measurement that can be easily applied.Our findings reveal that the characteristics of the coal-rock in the two mining faces are different;yet their caving angles follow the ruleφ_(igneous rock structure)<φ_(no geological structure)<φ_(fault structure).Finally,through the data fitting with two indexes(the top coal uniaxial compressive strength and the top caving angle),it is found that the relationship between the two indexes satisfies an exponential decay function.

Characteristics of Gas Emission at Super-Length Fully-Mechanized Top Coal Caving Face

Characteristics of gas emission at the K8206 working face in the Third mine of the Yangquan Coal Group were investigated. The effects of strata movement,advancing velocity of working face,production capacity of working face and gas extraction capability of strike high-level entry on gas emission at K8206 working face were analyzed. A regression equation,reflecting the relationship between relative gas emission rate and the production capacity of work-ing faces,was established. Another regression equation showing the relationship between the gas emission rate from adjacent layers when the working face was advancing for one metre and advancing velocity was derived. It can be con-cluded that,1) the amount of gas emitted at the K8206 working face is far greater than that of ordinary top coal caving faces with a dip length of 180-190 m; 2) the dynamic process of gas emission from adjacent layers during the initial mining stage is controlled by the movement of key strata; 3) the amount of gas emitted that needs to be forced out by air is greatly affected by the capability of gas extraction; 4) when the advancing velocity is between 3.5-5.5 m/d or when the output is up to 8-12 kt/d,the gas emission from adjacent layers is almost constant.

Analysis of the dialectical relation between top coal caving and coal-gas outbtu rst

According to the different engineering mechanical states of top coal caving andnormal stoping of gaseous loose thick coal seams,the dialectical relation between thiscaving method and dynamic disasters was analyzed by simulating the change of stressstates in the process of top coal initial caving with different mining and caving ratios basedon the ANSYS10.0.The variation of elastic energy and methane expansion energy duringfirst top coal caving was analyzed by first weighting and periodic weighting and combiningwith coal stress and deformation distribution of top coal normal stoping as well as positiveand negative examples in top coal caving of outburst coal seam.The research shows thatthe outburst risk increases along with the increase of the caving ratio in the initial miningstage.In the period of normal stoping,when the mining and caving ratio is smaller than1:3 and hard and massive overlying strata do not exist (periodic weighting is not obvious),it is beneficial to control ground stress leading type outburst.Thus,it is unreasonable toprohibit top coal caving in dangerous and outburst prone areas.

Deformation mechanism of surrounding rocks and key control technology for a roadway driven along goaf in fully mechanized top-coal caving face

The variation of the stress in the bolted surrounding rocks structure of the roadway driven along goaf in a fully mechanized top coal caving face with moderate stable conditions are studied by using numerical calculation. The essential deformation characteristics of the surrounding rocks in this kind of roadway are obtained and the key technology of bolting support used under these conditions is put forward.

Numerical investigation on the caving mechanism with different standard deviations of top coal block size in LTCC

The size distribution of the broken top coal blocks is an important factor,affecting the recovery ratio and the efficiency of drawing top coal in longwall top coal caving(LTCC)mining panel.The standard deviation of top coal block size(dt)is one of the main parameters to reflect the size distribution of top coal.To find the effect of dt on the caving mechanism,this study simulates experiments with 9 different dt by using discrete element software PFC.The dt is divided into two stages:uniform distribution stage(UDS)whose dt is less than 0.1(Schemes 1–5),and nonuniform distribution stage(NDS)whose dt is more than 0.1(Schemes 6–9).This research mainly investigates the variation of recovery ratio,drawing body shape,boundary of top coal,and contact force between particles in the two stages,respectively.The results showed that with the increasing dt,the recovery ratio of the panel increases first and then decreases in UDS.It is the largest in Scheme 3,which mainly increases the drawing volume at the side of starting drawing end.However,the recovery ratio decreases first and then increases quickly in NDS,and it is the largest in Scheme 9,where the drawing volume at the side of finishing drawing end are relatively higher.In UDS,the major size of top coal is basically medium,while in NDS,the size varies from medium to small,and then to large,with a distinct difference in shape and volume of the drawing body.When the major size of top coal is medium and small,the cross-section width of the initial boundary of top coal at each height is relatively small.Conversely,when the top coal size is large,the initial boundary of top coal has a larger opening range,the rotating angle of lower boundary is relatively small in the normal drawing stage,which is conducive to the development of drawing body and reduces the residual top coal,and the maximum particle velocity and the particles movement angle are both larger.This study lays a foundation for the prediction of recovery ratio,and suggests that the uniform top coal is more manageable and has a larger recovery ratio.

Study on destressing technology for a roadway driven along goaf in a fully mechanized top-coal caving face

Based on the deformation characteristics of the roadways driven along goaf in fully mechanized top coal caving faces, the author considers that it is the key to ensure the stability of surrounding rocks of roadway driven along goaf to control the deformation during the period affected by mining. Considering the characteristics of the roadway layout in fully mechanized top coal caving faces, a technical scheme of destressing is put forward and the destressing effect is analyzed by using the software of Universal Distinct Element Code 3 0(UDEC 3 0).

Mechanisms and Kinematics of Hydraulic Support for Top-Coal Caving

The structure and characteristic of new type of hydraulic support for top coal caving were discussed. The mechanism and kinematics of the hydraulic support were analyzed. The formulas were deduced to calculate the velocity and acceleration of top beam, shield beam, front and back legs, which give the solution to the design and research for hydraulic support.

Hydraulic support stability control of fully mechanized top coal caving face with steep coal seams based on instable critical angle

Analyzed the support instable mode of sliding,tripping,and so on,and believed the key point of the support stability control of fully mechanized coal caving face with steep coal seams was to maintain that the seam true angle was less than the hydraulic support instability critical angle.Through the layout of oblique face,the improvement of support setting load,the control of mining height and nonskid platform,the group support system of end face,the advance optimization of conveyor and support,and the other control tech- nical measures,the true angle of the seam is reduced and the instable critical angle of the support is increased,the hydraulic support stability of fully mechanized coal caving face with steep coal seams is effectively controlled.