Stability and accuracy of central difference method for real-time dynamic substructure testing considering mass participation coefficient

For real-time dynamic substructure testing(RTDST),the influence of the inertia force of fluid specimens on the stability and accuracy of the integration algorithms has never been investigated.Therefore,this study proposes to investigate the stability and accuracy of the central difference method(CDM)for RTDST considering the specimen mass participation coefficient.First,the theory of the CDM for RTDST is presented.Next,the stability and accuracy of the CDM for RTDST considering the specimen mass participation coefficient are investigated.Finally,numerical simulations and experimental tests are conducted for verifying the effectiveness of the method.The study indicates that the stability of the algorithm is affected by the mass participation coefficient of the specimen,and the stability limit first increases and then decreases as the mass participation coefficient increases.In most cases,the mass participation coefficient will increase the stability limit of the algorithm,but in specific circumstances,the algorithm may lose its stability.The stability and accuracy of the CDM considering the mass participation coefficient are verified by numerical simulations and experimental tests on a three-story frame structure with a tuned liquid damper.

Testing method of rock structural plane using digital drilling

The rock mass consists of rock blocks and structural planes,which can reduce its integrity and strength.Therefore,accurately obtaining the characteristics of the rock mass structural plane is a prerequisite for evaluating stability and designing supports in underground engineering.Currently,there are no effective testing methods for the characteristic parameters of the rock mass structural plane in underground engineering.The paper presents the digital drilling technology as a new testing method of rock mass structural planes.Flawed rock specimens with cracks of varying widths and angles were used to simulate the rock mass structural planes,and the multifunctional rock mass digital drilling test system was employed to carry out the digital drilling tests.The analysis focuses on the variation laws of drilling parameters,such as drilling pressure and drilling torque,affected by the characteristics of prefabricated cracks,and clarifies the degradation mechanism of rock equivalent compressive strength.Additionally,an identification model for the characteristic parameters of rock mass structural planes during drilling is established.The test results indicate that the average difference of the characteristics of prefabricated cracks identified by the equivalent compressive strength is 2.45°and 0.82 mm,respectively.The identification model while drilling is verified to be correct due to the high identification accuracy.Based on this,a method for testing the characteristic parameters of the surrounding rock structural plane while drilling is proposed.The research offers a theoretical and methodological foundation for precise in situ identification of structural planes of the surrounding rock in underground engineering.

Establishment of Microbial Limit Test Methods for Two Hospital Preparations

[Objectives] This study was conducted to establish microbial limit test methods for traditional Chinese medicine preparations Yunpi Granules and Bupi Qiangli Paste. [Methods] According to General Rules of Part IV of Chinese Pharmacopoeia, applicability tests were conducted on microbial limit test methods for the above two traditional Chinese medicine preparations by the plate method. [Results] The established methods showed recovery values in the range of 0.5-2.0 for both experimental strains, and the control bacteria could be detected in the experimental group, but not in the negative control group. [Conclusions] The microbial limit test methods were reliable for the two traditional Chinese medicine preparations and could be used for quality control.

Application of the extended Fourier amplitude sensitivity testing(FAST)method to inflated,axial stretched,and residually stressed cylinders

This paper is dedicated to applying the Fourier amplitude sensitivity test(FAST)method to the problem of mixed extension and inflation of a circular cylindrical tube in the presence of residual stresses.The metafunctions and the Ishigami function are considered in the sensitivity analysis(SA).The effects of the input variables on the output variables are investigated,and the most important parameters of the system under the applied pressure and axial force such as the axial stretch and the azimuthal stretch are determined.

Applicability of Microbial Limit Test Method for Qingyan Zhisou Powder

[Objectives]This study was conducted to establish a microbial limit test method for Qingyan Zhisou Powder.[Methods]Applicability tests were carried out according to Microbial Limit Tests of Non-sterile Products,General Rules 1105-1107 of Part IV of Chinese Pharmacopoeia,2020.[Results]Qingyan Zhisou Powder had a strong bacteriostatic effect on Pseudomonas aeruginosa.After increasing the dilution ratio(1:40),the bacteriostatic effect was obviously eliminated.When the total number of aerobic microbes was determined by the test liquid dilution method(1:40),the recovery values were in the range of 50%-200%;and when using the test liquid(1:10)to determine the total number of mold and yeasts,the recovery ranged from 50%to 200%.Escherichia coli,Salmonella and bile-tolerant Gram-negative bacteria were detected by both the routine method and dilution method in experimental groups.[Conclusions]The microbial limit test of Qingyan Zhisou Powder adopted the test liquid dilution method,and the routine method could be used for the test of Escherichia coli,Salmonella and bile-tolerant Gram-negative bacteria.The applicability test of the method is feasible,with scientific and accurate results,and the method can effectively control the quality of the preparation and is recommended for popularization.

Model test of negative Poisson’s ratio cable for supporting super-largespan tunnel using excavation compensation method

In recent years,there is a scenario in urban tunnel constructions to build super-large-span tunnels for traffic diversion and route optimization purposes.However,the increased size makes tunnel support more difficult.Unfortunately,there are few studies on the failure and support mechanism of the surrounding rocks in the excavation of supported tunnel,while most model tests of super-large-span tunnels focus on the failure characteristics of surrounding rocks in tunnel excavation without supports.Based on excavation compensation method(ECM),model tests of a super-large-span tunnel excavation by different anchor cable support methods in the initial support stage were carried out.The results indicate that during excavation of super-large-span tunnel,the stress and displacement of the shallow surrounding rocks decrease,following a step-shape pattern,and the tunnel failure is mainly concentrated on the vault and spandrel areas.Compared with conventional anchor cable supports,the NPR(negative Poisson’s ratio)anchor cable support is more suitable for the initial support stage of the super-large-span tunnels.The tunnel support theory,model test materials,methods,and the results obtained in this study could provide references for study of similar super-large-span tunnels。

Mobility and dynamic erosion process of granular flow:insights from numerical investigation using material point method

In order to understand the dynamics of granular flow on an erodible base soil,in this paper,a series of material point method-based granular column collapse tests were conducted to investigate numerically the mobility and dynamic erosion process of granular flow subjected to the complex settings,i.e.,the aspect ratio,granular mass,friction and dilatancy resistance,gravity and presence of water.A set of power scaling laws were proposed to describe the final deposit characteristics of granular flow by the relations of the normalized run-out distance and the normalized final height of granular flow against the aspect ratio,being greatly affected by the complex geological settings,e.g.,granular mass,the friction and dilatancy resistance of granular soil,and presence of water in granular flow.An index of the coefficient of friction of granular soil was defined as a ratio of the target coefficient of friction over the initial coefficient of friction to quantify the scaling extent of friction change(i.e.,friction strengthening or weakening).There is a characteristic aspect ratio of granular column corresponding to the maximum mobility of granular flow with the minimum index of the apparent coefficient of friction.The index of the repose coefficient of friction of granular flow decreased gradually with the increase in aspect ratio because higher potential energy of granular column at a larger aspect ratio causes a larger kinetic energy of granular soil to weaken the friction of granular soil as a kind of velocity-related friction weakening.An increase in granular mass reduces gradually the indexes of the apparent and repose coefficients of friction of granular soil to enhance the mobility of granular flow.The mobility of granular flow increases gradually with the decrease in friction angle or increase in dilatancy angle of granular soil.However,the increase of gravity accelerates granular flow but showing the same final deposit profile without any dependence on gravity.The mobility of granular flow increases gradually by lowering the indexes of the apparent and repose coefficients of friction of granular flow while changing the surroundings,in turn,the dry soil,submerged soil and saturated soil,implying a gradually increased excessive mobility of granular flow with the friction weakening of granular soil.Presence of water in granular flow may be a potential catalyzer to yield a long run-out granular flow,as revealed in comparison of water-absent and water-present granular flows.In addition,the dynamic erosion and entrainment of based soil induced by granular flow subjected to the complex geological settings,i.e.,the aspect ratio,granular mass,gravity,friction and dilatancy resistance,and presence of water,were comprehensively investigated as well.

Seismic effectiveness evaluation and optimized design of tie up method for securing museum collections

To quantify the seismic effectiveness of the most commonly used fishing line tie up method for securing museum collections and optimize fixed strategies for exhibitions,shaking table tests of the seismic systems used for typical museum collection replicas have been carried out.The influence of body shape and fixed measure parameters on the seismic responses of replicas and the interaction behavior between replicas and fixed measures have been explored.Based on the results,seismic effectiveness evaluation indexes of the tie up method are proposed.Reasonable suggestions for fixed strategies are given,which provide a basis for the exhibition of delicate museum collections considering the principle of minimizing seismic responses and intervention.The analysis results show that a larger ratio of height of mass center to bottom diameter led to more intense rocking responses.Increasing the initial pretension of fishing lines was conducive to reducing the seismic responses and stress variation of the lines.Through comprehensive consideration of the interaction forces and effective securement,it is recommended to apply 20%of breaking stress as the initial pretension.For specific museum collections that cannot be effectively protected by the independent tie up method,an optimized strategy of a combination of fishing lines and fasteners is recommended.

Determination of Material Parameters of EVA Foam under Uniaxial Compressive Testing Using Hyperelastic Models

The objective of this research was to determine the mechanical parameter from EVA foam and also investigate its behavior by using Blatz-Ko,Neo-Hookean,Mooney model and experimental test.The physical characteristic of EVA foam was also evaluated by scanning electron microscopy(SEM).The results show that Blatz-Ko and Neo-Hookean model can fit the curve at 5%and 8%strain,respectively.The Mooney model can fit the curve at 50%strain.The modulus of rigidity evaluated from Mooney model is 0.0814±0.0027 MPa.The structure of EVA foam from SEM image shows that EVA structure is a closed cell with homogeneous porous structure.From the result,it is found that Mooney model can adjust the data better than other models.This model can be applied for mechanical response prediction of EVA foam and also for reference value in engineering application.

基于Aquifertest计算大海则矿井水文地质参数及涌水量

抽水试验是一种在水文地质勘查中最为常用的水文地质试验,以榆林市大海则井田相关资料为依据,通过抽水试验,利用Aquifertest软件中的纽曼模型和博尔顿模型分别对水文地质参数进行确定,最终得出了相应的导水系数值为0.200 m^(2) /min、给水度值0.024、贮水系数值0.000177、渗透系数值4.434 m/d,并采用水平廊道法计算矿坑涌水量为大海则煤矿的涌水量为5169.351 m^(3) /d。此方法误差较小结果可靠,为快速高效地进行水文地质参数计算和涌水量预测提供一种有效方法,同时为后续矿床开采及施工建设提供参考依据。

Virtual rutting test of asphalt mixture using discrete element method

In order to investigate the permanent deformation behavior of asphalt mixtures from discontinuity, the virtual rutting test of asphalt mixtures is developed by the discrete element method （DEM）. A digital specimen generation procedure considering aggregate gradation and irregular shape is developed based on the probability theory and the Monte Carlo method. The virtual rutting test is then conducted based on the generated digital specimen. In addition, on the basis of the time-temperature superposition （TTS） principle, a calculation method is used to reduce the computation time of the virtual rutting test. The simulation results are compared with the laboratory measurements. The results show that the calculation method based on the TFS principle in the discrete element （DE） viscoelastic model can significantly reduce the computation time. The deformation law of asphalt mixtures in the virtual rutting test is similar to the laboratory measurements, and the deformation and the dynamic stability of the virtual rutting test are slightly greater than the laboratory measurements. The two-dimensional virtual rutting test can predict the permanent deformation performance of asphalt mixtures.

Virtual fracture test of asphalt mixture based on discrete element method

In order to study fracture behaviors of asphalt mixtures, virtual tests of the two-dimensional（2D） microstructure based on the discrete element method（ DEM） are designed. The virtual structure of the 2D digital specimen of asphalt mixture is generated based on a particle generation program, in which the gradation and the irregular shapes of aggregates are considered. With the 2D digital specimens, a DEM-based mixture model is established and center-point beam fracture simulation tests are conducted by the DEM. Meanwhile, a series of calibration tests are carried out in laboratory to evaluate the DEM model and validate the methods of virtual fracture tests. The test results indicate that the fracture intensity of asphalt mixtures predicted by the DEM matches very well with the intensity obtained in laboratory. It is concluded that the microstructural virtual tests can be used as a supplemental tool to evaluate fracture properties of asphalt mixtures.

Research on the Testing Methods of Instrumental System in the Marine Magnetic Survey

Testing methods of instrumental system in the marine magnetic survey have been studied in this paper, and the feasibility of each method has been testified by the observed data. The conclusion shows that the method brought out can effectively eliminate the systematic error caused by the instrumental system, and greatly improve the surveying precision and the reliability of the survey results.

New Fatigue Test and Statistical Method for Metallic Materials Used in Vehicle Transmissions

Aim To improve the efficiency of fatigue material tests and relevant statistical treatment of test data. Methods\ Least square approach and other special treatments were used. Results and Conclusion\ The concepts of each phase in fatigue tests and statistical treatment are clarified. The method proposed leads to three important properties. Reduced number of specimens brings to the advantage of lowering test expenditures. The whole test procedure has more flexibility for there is no need to conduct many tests at the same stress level as in traditional cases.

Analysis of the integrated test and evaluation methods of tidal current energy generating devices in the offshore testing site

Actual sea condition testing and inspection and evaluation method research are carried out for tidal energy devices to provide scientific and effective technical support for the ocean high-tech achievement transformation and marine renewable energy development. By analyzing three core indicators, including the power output characteristics of the tidal current device, the generating capacity, energy conversion efficiency, proposed the test contents and evaluation methods of indicators are proposed in this paper; and based on the research of wind farms, power quality testing and assessment methods of offshore tidal energy device are proposed; given the security access to the test contents of tidal current energy device, tidal current energy device running conditions in the testing ground are comprehensively assessed.

Method of Growth in Finding the Test Cube of Industrial Robots

In order to find the test cube for industrial robots as specified by ISO 9283, a seed cube is grown up in an irregular working space of the robot, provided that the corners of the cube do not exceed the boundary of the working space. All possible cubes are searched, and the cube with the maximum volume is selected. The calculation examples show that the method of growth can be used for a variety of industrial robots. The method of growth can determine the test cube and test points of irregular working space according to ISO 9283, and can avoid blindness and randomness in the selection of test points.

Methodology Validation of Microbial Limit Test of Bupi Qiangli Ointment

[Objective] This study was conducted to establish a microbial limit test method for Bupi Qiangli Ointment. [Method] The conventional method and medium dilution method were used for bacterial, mold and yeast counting in sample recovery test. [Result] The medium dilution method （1：10 test solution, 0.5 ml/plate） could effectively eliminate the inhibition effect of the Bupi Qiangli Ointment, and the recovery of Staphylococcus aureus was greater than 70% in the 3 batches of samples; and the conventional method exhibited the recoveries of E. coil, Bacillus subtilis, Candida albicans and Aspergillus greater than 70% in the 3 batches of samples. [Conclusion] Due to Bupi Qiangli Ointment has strongly antibacterial effect on Staphylococcus au- reus, the medium dilution method was used for bacterial counting, and the conventional method was used for mold and yeast counting; and the conventional method was used for controlled bacterium examination of E. coll.

Investigation on the test method of rupture forces of thermal bonding seams in nonwovens shopping bags

超声波热黏合的非织造布接缝不同于普通机织物和针织物等的车缝接缝。运用正交试验设计方法，对纺粘法PP非织造布购物袋热黏合接缝断裂强力测试中的试样宽度、拉伸速率和隔距三个因素进行优化。试验结果表明，试样宽度对纺粘法PP非织造布热黏合接缝断裂强力的测试结果影响最大，并且接缝的断裂强力随着试样宽度的增加而增加。选用试样宽度为200mm、拉伸速率为50mm／min、隔距为100mm的组合所得出的测试结果能比较真实地反映实际的接缝断裂强力。

Real-time embedded software testing method based on extended finite state machine

The reliability of real-time embedded software directly determines the reliability of the whole real-time embedded sys- tem, and the effective software testing is an important way to ensure software quality and reliability. Based on the analysis of the characteristics of real-time embedded software, the formal method is introduced into the real-time embedded software testing field and the real-time extended finite state machine （RT-EFSM） model is studied firstly. Then, the time zone division method of real-time embedded system is presented and the definition and description methods of time-constrained transition equivalence class （timeCTEC） are presented. Furthermore, the approaches of the testing sequence and test case generation are put forward. Finally, the proposed method is applied to a typical avionics real- time embedded software testing practice and the examples of the timeCTEC, testing sequences and test cases are given. With the analysis of the testing result, the application verification shows that the proposed method can effectively describe the real-time embedded software state transition characteristics and real-time requirements and play the advantages of the formal methods in accuracy, effectiveness and the automation supporting. Combined with the testing platform, the real-time, closed loop and automated simulation testing for real-time embedded software can be realized effectively.

Studying the mechanical properties of the soil-root interface using the pullout test method

It is important to quantify the effect of the root diameter, the embedment length of the root and load speed on the soil-root interface mechanical properties for studying the root anchorage. The soilroot interface mechanical properties can be obtained through the pullout force and root slippage curve(F-S curve). About 120 Pinus tabulaeformis single roots whose diameters ranged from 1 mm to 10 mm divided into 6 groups based on different root embedment length(50 mm, 100 mm and 150 mm) and different load velocity(10 mm·min^(-1), 50 mm·min^(-1), 100 mm·min^(-1) and 300 mm·min^(-1)) were investigated using the pullout method. This study aims to explore the mechanical properties of the soil-root interface in the real conditions using the pullout test method. The results showed two kinds of pullout test failure modes during the experimental process: breakage failure and pullout failure. The results showed that the roots were easier to be broken when the root diameter was smaller or the loading speed was larger. The relationship between the maximum anchorage force and root diameter was linear and the linearly dependent coefficient(R^2) was larger than 0.85. The anchorage force increased with the root embedment length. An increase of 10%^(-1)5% for the maximumanchorage force was found when load speed increased from 10 to 300 mm.min^(-1). The mean peak slippage of the root was from 13.81 to 35.79 mm when the load velocity varied from 10 to 300 mm.min^(-1). The study will be helpful for the design of slopes reinforced by vegetation and in predicting risk of uprooting of trees, and will have practical benefits for understanding the mechanism of landslide.