Experimental study on the degree and damage-control mechanisms of fuzzy-ball-induced damage in single and multi-layer commingled tight reservoirs

Fuzzy-ball working fluids(FBWFs)have been successfully applied in different development phases of tight reservoirs.Field reports revealed that FBWFs satisfactorily met all the operational and reservoir damage control requirements during their application.However,the damage-control mechanisms and degree of formation damage caused by fuzzy-ball fluids have not been investigated in lab-scale studies so far.In this study,the degree of fuzzy-ball-induced damage in single-and double-layer reservoirs was evaluated through core flooding experiments that were based on permeability and flow rate indexes.Additionally,its damage mechanisms were observed via scanning electron microscope and energy-dispersive spectroscopy tests.The results show that:(1)For single-layer reservoirs,the FBWF induced weak damage on coals and medium-to-weak damage on sandstones,and the difference of the damage in permeability or flow rate index on coals and sandstones is below 1%.Moreover,the minimum permeability recovery rate was above 66%.(2)For double-layer commingled reservoirs,the flow rate index revealed weak damage and the overall damage in double-layer was lower than the single-layer reservoirs.(3)There is no significant alteration in the microscopic structure of fuzzy-ball saturated cores with no evidence of fines migration.The dissolution of lead and sulfur occurred in coal samples,while tellurium in sandstone,aluminum,and magnesium in carbonate.However,the precipitation of aluminum,magnesium,and sodium occurred in sandstone but no precipitates found in coal and carbonate.The temporal plugging and dispersion characteristics of the FBWFs enable the generation of reservoir protection layers that will minimize formation damage due to solid and fluid invasion.

Evaluation of hydraulic fracturing of horizontal wells in tight reservoirs based on the deep neural network with physical constraints

Accurate diagnosis of fracture geometry and conductivity is of great challenge due to the complex morphology of volumetric fracture network. In this study, a DNN (deep neural network) model was proposed to predict fracture parameters for the evaluation of the fracturing effects. Field experience and the law of fracture volume conservation were incorporated as physical constraints to improve the prediction accuracy due to small amount of data. A combined neural network was adopted to input both static geological and dynamic fracturing data. The structure of the DNN was optimized and the model was validated through k-fold cross-validation. Results indicate that this DNN model is capable of predicting the fracture parameters accurately with a low relative error of under 10% and good generalization ability. The adoptions of the combined neural network, physical constraints, and k-fold cross-validation improve the model performance. Specifically, the root-mean-square error (RMSE) of the model decreases by 71.9% and 56% respectively with the combined neural network as the input model and the consideration of physical constraints. The mean square error (MRE) of fracture parameters reduces by 75% because the k-fold cross-validation improves the rationality of data set dividing. The model based on the DNN with physical constraints proposed in this study provides foundations for the optimization of fracturing design and improves the efficiency of fracture diagnosis in tight oil and gas reservoirs.

Genesis and microscopic characteristics of tight reservoirs in the Fengcheng Formation, at the southern margin of the Mahu Sag

The tight reservoirs of the Fengcheng Formation at the southern margin of the Mahu Sag have strong heterogeneity due to the diversity in their pore types, sizes, and structures. The microscopic characteristics of tight reservoirs and the mechanisms that generate them are of significance in identifying the distribution of high-quality reservoirs and in improving the prediction accuracy of sweet spots in tight oil reservoirs. In this paper, high-pressure mercury intrusion (HPMI) and nuclear magnetic resonance (NMR) experiments were carried out on samples from the tight reservoirs in the study area. These experimental results were combined with cluster analysis, fractal theory, and microscopic observations to qualitatively and quantitatively evaluate pore types, sizes, and structures. A classification scheme was established that divides the reservoir into four types, based on the microstructure characteristics of samples, and the genetic mechanisms that aided the development of reservoir microstructure were analyzed. The results show that the lower limit for the tight reservoir in the Fengcheng Formation is Φ of 3.5% and K of 0.03 mD. The pore throat size and distribution span gradually decrease from Type I, through Type II and Type III reservoirs to non-reservoirs, and the pore type also evolves from dominantly intergranular pores to intercrystalline pores. The structural trend shows a decrease in the ball-stick pore-throat system and an increase in the branch-like pore-throat system. The dual effects of sedimentation and diagenesis shape the microscopic characteristics of pores and throats. The sorting, roundness, and particle size of the original sediments determine the original physical properties of the reservoir. The diagenetic environment of ‘two alkalinity stages and one acidity stage’ influenced the evolution of pore type and size. Although the cementation of authigenic minerals in the early alkaline environment adversely affected reservoir properties, it also alleviated the damage of the later compaction to some extent. Dissolution in the mid-term acidic environment greatly improved the physical properties of this tight reservoir, making dissolution pores an important reservoir space. The late alkaline environment occurred after large-scale oil and gas accumulation. During this period, the cementation of authigenic minerals had a limited effect on the reservoir space occupied by crude oil. It had a more significant impact on the sand bodies not filled with oil, making them function as barriers.

Numerical investigation of refracturing with/without temporarily plugging diverters in tight reservoirs

Refracturing is an importa nt technique to tap the potential of reservoirs and boost production in depleted oil and gas fields.However,fracture propagation during refracturing,including both conventional refracturing and temporary-plugging refracturing remains poorly understood,especially for cases with non-uniform distribution of formation pressure due to long-term oil production and water injection.Therefore,taking pilot tests of refracturing with sidetracking horizontal wells in tight reservoirs in the Changqing Oilfield,China as an example,we establish a three-dimensional numerical model of conventional refracturing and a numerical model of temporary-plugging refracturing based on the discrete lattice method.Non-uniform distributions of formation pressure are imported in these models.We discuss the effects of key operating parameters such as injection rate,cluster spacing,and number of clusters on the propagation of multi-cluster fractures for conventional refracturing.For temporaryplugging refracturing,we examine the impacts of controlling factors such as the timing and number of temporary plugging on fracture propagation.In addition,we analyze a field case of temporaryplugging refracturing using well P3 in the Changqing Oilfield.The results show that fractures during re fracturing tend to propagate preferentially and dominantly in the depleted areas.Improved stimulation effect can be obtained with an optimal injection rate and a critical cluster spacing.The proposed model of temporary-plugging refracturing can well describe the temporary plugging of dominant existingfractures and the creation of new-fractures after fracturing fluid is forced to divert into other clusters from previous dominant clusters.Multiple temporary plugging can improve the balanced propagation of multi-cluster fractures and obtain the maximum fracture area.The established numerical model and research results provide theoretical guidance for the design and optimization of key operating parameters for refracturing,especially for temporary-plugging refracturing.

Experimental Investigation on the Pressure Propagation Mechanism of Tight Reservoirs

Low permeability tight sandstone reservoirs have a high filtrational resistance and a very low fluid flow rate.As a result,the propagation speed of the formation pressure is low and fluid flow behaves as a non-Darcy flow,which typically displays a highly non-linear behavior.In this paper,the characteristics and mechanism of pressure propagation in this kind of reservoir are revealed through a laboratory pressure propagation experiment and through data from an actual tight reservoir development.The main performance mechanism is as follows:A new pressure cage concept is proposed based on the pressure variation characteristics of the laboratory experiments.There are two methods of energy propagation in the actual water injection process:one is that energy is transmitted to the deep reservoir by the fluid flowing through the reservoir,and the other is that energy is transmitted by the elasticity of the reservoir.For one injection well model and one production well model,the pressure distribution curve between the injection and production wells,as calculated by the theoretical method,has three section types,and they show an oblique“S”shape with a straight middle section.However,the actual pressure distribution curve is nonlinear,with an obvious pressure advance at the front.After the injection pressure increases to a certain level,the curve shape is an oblique and reversed“S”shape.Based on the research,this paper explains the deep-seated reasons for the difference in pressure distribution and proposes that it is an effective way to develop low permeability tight reservoirs using the water injection supplement energy method.

Techniques for improving fracture-controlled stimulated reservoir volume in ultra-deep fractured tight reservoirs: A case study of Kuqa piedmont clastic reservoirs, Tarim Basin, NW China

Based on analysis of the reasons for low efficiency and low production after fracturing of some wells in the ultra-deep fractured tight reservoirs of the Kuqa piedmont zone, Tarim Basin and the matching relationship between the in-situ stress field and natural fractures, technological methods for creating complex fracture networks are proposed. Through theoretical study and large-scale physical simulation experiments, the mechanical conditions for forming complex fracture network in the Kuqa piedmont ultra-deep reservoirs are determined. The effectiveness of temporary plugging and diversion, and multi-stage fracturing to activate natural fractures and consequently realize multi-stage diversion is verified. The coupling effect of hydraulic fractures and natural fractures activating each other and resulting in "fracture swarms" is observed. These insights provide theoretical support for improving fracture-controlled stimulated reservoir volume(FSRV) in ultra-deep tight reservoirs. In addition, following the concept of volume fracturing technology and based on the results of fracture conductivity experiments of different processes, fracturing technologies such as multi-stage fracture-network acid fracturing, "multi-stage temporary plugging + secondary fracturing", fracturing of multiple small layers by vertically softness-and-hardness-oriented subdivision, and weighted-fluid refracturing are proposed to increase the FSRV. New environment-friendly weighted-fluid with low cost and new fracturing fluid system with low viscosity and high proppant-carrying capacity are also developed. These techniques have achieved remarkable results in field application.

Pore throat structure and classification of Paleogene tight reservoirs in Jiyang depression,Bohai Bay Basin,China

The pore throat structure characteristics of Paleogene tight sandstone and sandy conglomerate in the Jiyang depression are studied using cast thin section,conventional mercury injection,constant rate mercury injection and micro CT scanning data,and a reservoir classification scheme based on pore throat structure parameters is established.The material composition and structural characteristics of tight reservoirs are analyzed by casting thin section data.The pore throat structure characteristics of tight reservoirs are studied by conventional mercury injection,constant rate mercury injection and micro CT scanning.Ten pore throat structure parameters are analyzed by cluster analysis.Based on the classification results and oil test results,the classification scheme of Paleogene tight reservoirs is established.The Paleogene tight reservoirs in the Jiyang depression have the characteristics of macropores and microthroats,with pores in micron scale,throats in nano-submicron scale,and wide variation of ratio of pore radius to throat radius.The permeability of the tight reservoir is controlled by throat radius,the smaller the difference between pore radius and throat radius,and the more uniform the pore throat size,the higher the permeability will be.The lower limits of average pore throat radius for the tight sandstone and tight sandy conglomerate to produce industrial oil flow without fracturing are 0.6μm and 0.8μm,respectively.Reservoirs that can produce industrial oil flow only after fracturing have an average pore-throat radius between 0.2-0.6μm,and reservoirs with average pore throat radius less than 0.2μm are ineffective reservoirs under the current fracturing techniques.Different types of tight sandstone and sandy conglomerate reservoirs are classified and evaluated,which are well applied in exploratory evaluation.

Advances and challenges in hydraulic fracturing of tight reservoirs: A critical review

The hydraulic fracturing technology has been widely utilized to extract tight resources.Hydraulic frac-turing involves rock failures,complex fracture generation,proppant transport and fracture closure.All these behaviors affect the productivity of fractured wells.In this work,the advances and challenges in hydraulic fracturing development of tight reservoirs are summarized from following aspects:the hy-draulic fracture propagation,the proppant transport and distribution in hydraulic fractures,the calcu-lation of hydraulic fracture conductivity,and productivity and/or pressure analysis model of multi-stages fractured horizontal wells.Current fracture propagation simulation methods generate only limited propagation paths and cannot truly reflect the complexity of the propagation.The current proppant migration and distribution research is mainly focused on indoor experimental studies of proppant migration in a single fracture or branched fracture,and simulation studies on proppant migration and distribution in a small-scale single slab fracture.Whereas fractures formed after hydraulic fracturing in tight reservoirs are generally complicated.There is a lack of models for calculating complex fracture conductivity that take into consideration the effect of proppant placement and proppant distribution in fractures,fracture surface roughness and dissolution,diffusion,deposition,elastic embedding,and creep caused by stress.The productivity models of fractured horizontal wells are mostly conducted based on the original reservoir fluid saturation and pressure distribution.Most of the studies are focused only on one aspect of the fracturing process.Predications of well performance after fracturing based on these studies are often inconsistent with actual field data.The paper also discusses the future research di-rections of fracturing in tight reservoirs and the results may be used to promote the development of tight reservoirs.

Characteristics and classification of paleozoic tight reservoirs in the central uplift of the South Yellow Sea Basin

Several sets of Paleozoic tight reservoirs are developed in the Central Uplift of the South Yellow Sea Basin.A qualitative analysis of the microscopic pore structure of the tight reservoir rocks was carried out through cast thin slice and scanning electron microscopic image observation.Based on reservoir pet-rophysical properties,thirty core samples in the Central Uplift of the South Yellow Sea Basin were selected for high-pressure mercury intrusion(HPMI)analysis,which was then combined with fractal calculation to classify and evaluate the tight reservoirs.The analysis of the HPMI curves and related parameters shows that the Paleozoic tight reservoirs can be divided into three types:Type-A,Type-B and Type-C.Type-A sandstone reservoirs contain pores with size mostly ranging between 0.01 and 0.1 mm,followed by pores with size range of 0.001-0.01 m m,and relatively fewer pores larger than 0.1 m m.The Type-B reservoirs are carbonate rocks with extremely heterogeneous pore size distribution,which is closely related to the development of dissolution pores and microfractures.Type-C sandstone reservoirs are dominated by nanopores and submicron pores that distribute more heterogeneously than pores in Type-A reservoirs.The pore distribution in sandstone reservoirs shows significant fractal characteristics and is closely related to the pore size.The heterogeneity of nanopore distribution has a negative cor-relation with porosity and median pressure and a relatively weak correlation with permeability.Our study has important implications for petroleum exploration in the South Yellow Sea Basin.

Further discussion of CO_(2) huff-n-puff mechanisms in tight oil reservoirs based on NMR monitored fluids spatial distributions

Due to the poor physical properties of tight reservoirs,CO_(2) huff-n-puff(HNP)is considered a potential enhanced oil recovery(EOR)method after primary depletion.Optimization plays a critical role in the effective implementation of CO_(2) huff-n-puff.But the optimization requires a good understanding of the EOR mechanisms.In this work,the spatial distribution of oil saturation under different experimental conditions was analyzed by the NMR method to further discuss the HNP mechanisms.According to the variation of 1D frequency signal amplitude,we divided the core into the hardly movable area and movable area,the region with the obvious signal decline was defined as the movable area,and the hardly movable area was the region with limited signal decline.Based on that the recovery characteristics of different scenarios were evaluated.Firstly,the necessity of the soaking stage was studied,where three scenarios with different soaking times were carried out.Secondly,the injection pressure was adjusted to investigate the effect of the pressure gradient.The T_(2) spectra show that soaking has significantly improved the production of crude oil in small pores,and higher oil recovery in a single cycle is observed,but it is lower when the elapsed time(total operation time)is the same.31.03% of oil can be recovered after 3 cycles HNP,which increases to 33.8% and 37.06% for the 4 cycles and 6 cycles cases.As the pressure gradient increases,more oil is removed out of the matrix,and the oil in the deep part of the reservoir can be effectively recovered.During the CO_(2) huff-n-puff process,the oil distributions are similar to the solution gas drive,the residual oil is distributed at the close end of the core and the range that the oil can be efficiently recovered is limited.

Investigation of influence factors on CO_(2) flowback characteristics and optimization of flowback parameters during CO_(2) dry fracturing in tight gas reservoirs

CO_(2) dry fracturing is a promising alternative method to water fracturing in tight gas reservoirs,especially in water-scarce areas such as the Loess Plateau.The CO_(2) flowback efficiency is a critical factor that affects the final gas production effect.However,there have been few studies focusing on the flowback characteristics after CO_(2) dry fracturing.In this study,an extensive core-to-field scale study was conducted to investigate CO_(2) flowback characteristics and CH_(4) production behavior.Firstly,to investigate the impact of core properties and production conditions on CO_(2) flowback,a series of laboratory experiments at the core scale were conducted.Then,the key factors affecting the flowback were analyzed using the grey correlation method based on field data.Finally,taking the construction parameters of Well S60 as an example,a dual-permeability model was used to characterize the different seepage fields in the matrix and fracture for tight gas reservoirs.The production parameters after CO_(2) dry fracturing were then optimized.Experimental results demonstrate that CO_(2) dry fracturing is more effective than slickwater fracturing,with a 9.2%increase in CH_(4) recovery.The increase in core permeability plays a positive role in improving CH_(4) production and CO_(2) flowback.The soaking process is mainly affected by CO_(2) diffusion,and the soaking time should be controlled within 12 h.Increasing the flowback pressure gradient results in a significant increase in both CH_(4) recovery and CO_(2) flowback efficiency.While,an increase in CO_(2) injection is not conducive to CH_(4) production and CO_(2) flowback.Based on the experimental and field data,the important factors affecting flowback and production were comprehensively and effectively discussed.The results show that permeability is the most important factor,followed by porosity and effective thickness.Considering flowback efficiency and the influence of proppant reflux,the injection volume should be the minimum volume that meets the requirements for generating fractures.The soaking time should be short which is 1 day in this study,and the optimal bottom hole flowback pressure should be set at 10 MPa.This study aims to improve the understanding of CO_(2) dry fracturing in tight gas reservoirs and provide valuable insights for optimizing the process parameters.

Simulation of Gas-Water Two-Phase Flow in Tight Gas Reservoirs Considering the Gas Slip Effect

A mathematical model for the gas-water two-phase flow in tight gas reservoirs is elaborated.The model can account for the gas slip effect,stress sensitivity,and high-speed non-Darcy factors.The related equations are solved in the framework of a finite element method.The results are validated against those obtained by using the commercial software CMG(Computer Modeling Group software for advanced recovery process simulation).It is shown that the proposed method is reliable.It can capture the fracture rejection characteristics of tight gas reservoirs better than the CMG.A sensitivity analysis of various control factors(initial water saturation,reservoir parameters,and fracturing parameters)affecting the production in tight gas wells is conducted accordingly.Finally,a series of theoretical arguments are provided for a rational and effective development/exploitation of tight sandstone gas reservoirs.

Quantitative characterization of tight gas sandstone reservoirs using seismic data via an integrated rock-physics-based framework

Seismic characterizing of tight gas sandstone (TGS) reservoirs is essential for identifying promising gas-bearing regions. However, exploring the petrophysical significance of seismic-inverted elastic properties is challenging due to the complex microstructures in TGSs. Meanwhile, interbedded structures of sandstone and mudstone intensify the difficulty in accurately extracting the crucial tight sandstone properties. An integrated rock-physics-based framework is proposed to estimate the reservoir quality of TGSs from seismic data. TGSs with complex pore structures are modeled using the double-porosity model, providing a practical tool to compute rock physics templates for reservoir parameter estimation. The VP/VS ratio is utilized to predict the cumulative thickness of the TGS reservoirs within the target range via the threshold value evaluated from wireline logs for lithology discrimination. This approach also facilitates better capturing the elastic properties of the TGSs for quantitative seismic interpretation. Total porosity is estimated from P-wave impedance using the correlation obtained based on wireline log analysis. After that, the three-dimensional rock-physics templates integrated with the estimated total porosity are constructed to interpret microfracture porosity and gas saturation from velocity ratio and bulk modulus. The integrated framework can optimally estimate the parameters dominating the reservoir quality. The results of the indicator proposed based on the obtained parameters are in good agreement with the gas productions and can be utilized to predict promising TGS reservoirs. Moreover, the results suggest that considering microfracture porosity allows a more accurate prediction of high-quality reservoirs, further validating the applicability of the proposed method in the studied region.

A transient production prediction method for tight condensate gas wells with multiphase flow

Considering the phase behaviors in condensate gas reservoirs and the oil-gas two-phase linear flow and boundary-dominated flow in the reservoir,a method for predicting the relationship between oil saturation and pressure in the full-path of tight condensate gas well is proposed,and a model for predicting the transient production from tight condensate gas wells with multiphase flow is established.The research indicates that the relationship curve between condensate oil saturation and pressure is crucial for calculating the pseudo-pressure.In the early stage of production or in areas far from the wellbore with high reservoir pressure,the condensate oil saturation can be calculated using early-stage production dynamic data through material balance models.In the late stage of production or in areas close to the wellbore with low reservoir pressure,the condensate oil saturation can be calculated using the data of constant composition expansion test.In the middle stages of production or when reservoir pressure is at an intermediate level,the data obtained from the previous two stages can be interpolated to form a complete full-path relationship curve between oil saturation and pressure.Through simulation and field application,the new method is verified to be reliable and practical.It can be applied for prediction of middle-stage and late-stage production of tight condensate gas wells and assessment of single-well recoverable reserves.

Revolutionizing Tight Reservoir Production: A Novel Dual-Medium Unsteady Seepage Model for Optimizing Volumetrically Fractured Horizontal Wells

This study presents an avant-garde approach for predicting and optimizing production in tight reservoirs,employing a dual-medium unsteady seepage model specifically fashioned for volumetrically fractured horizontal wells.Traditional models often fail to fully capture the complex dynamics associated with these unconventional reservoirs.In a significant departure from these models,our approach incorporates an initiation pressure gradient and a discrete fracture seepage network,providing a more realistic representation of the seepage process.The model also integrates an enhanced fluid-solid interaction,which allows for a more comprehensive understanding of the fluid-structure interactions in the reservoir.This is achieved through the incorporation of improved permeability and stress coupling,leading to more precise predictions of reservoir behavior.The numerical solutions derived from the model are obtained through the sophisticated finite element method,ensuring high accuracy and computational efficiency.To ensure the model’s reliability and accuracy,the outcomes were tested against a real-world case,with results demonstrating strong alignment.A key revelation from the study is the significant difference between uncoupled and fully coupled volumetrically fractured horizontal wells,challenging conventional wisdom in the field.Additionally,the study delves into the effects of stress,fracture length,and fracture number on reservoir production,contributing valuable insights for the design and optimization of tight reservoirs.The findings from this study have the potential to revolutionize the field of tight reservoir prediction and management,offering significant advancements in petroleum engineering.The proposed approach brings forth a more nuanced understanding of tight reservoir systems and opens up new avenues for optimizing reservoir management and production.

Blasingame production decline type curves for analysing a multi-fractured horizontal well in tight gas reservoirs

Production decline analysis has been considered as an important method to obtain the flow parameters, reservoir properties and original gas in place. Although advanced Blasingame production decline analysis methods for vertical wells, fractured wells and horizontal wells are widely used, limited study has conducted on Blasingame production decline type curves for multi-fractured horizontal well(MFHW). Based on the perpendicular bisection(PEBI) grids, a numerical model was developed and the solution was obtained using control volume finite element method and the fully implicit method. Blasingame production decline-type curves of the infinitely conductive MFHW were plotted through computer programming. A field case was presented to analyse and verify the model developed. Five flow regimes, including early formation linear flow, early radial flow, compound linear flow, transient flow and pseudo-radial flow, are recognized. Fracture spacing is the main factor that affects early radial flow, compound linear flow and transient flow, the distance from the well to the circular boundary affects the pseudo-radial flow, and the type curves are also significantly affected by the formation permeability, fracture number and fracture half-length. The validation of field case suggests that the Blasingame production decline type curves proposed in this work can be applied to the production decline analysis for MFHW in tight gas reservoirs.

Laboratory to field scale assessment for EOR applicability in tight oil reservoirs

Tight oil reservoirs are contributing a major role to fulfill the overall crude oil needs,especially in the US.However,the dilemma is their ultra-tight permeability and an uneconomically short-lived primary recovery factor.Therefore,the application of EOR in the early reservoir development phase is considered effective for fast-paced and economical tight oil recovery.To achieve these objectives,it is imperative to determine the optimum EOR potential and the best-suited EOR application for every individual tight oil reservoir to maximize its ultimate recovery factor.Since most of the tight oil reservoirs are found in wide spatial source rock with complex and compacted pores and poor geophysical properties yet they hold high saturation of good quality oil and therefore,every single percent increase in oil recovery from such huge reservoirs potentially provide an additional million barrels of oil.Hence,the EOR application in such reservoirs is quite essential.However,the physical understanding of EOR applications in different circumstances from laboratory to field scale is the key to success and similarly,the fundamental physical concepts of fluid flow-dynamics under confinement conditions play an important role.This paper presents a detailed discussion on laboratory-based experimental achievements at micro-scale including fundamental concepts under confinement environment,physics-based numerical studies,and recent actual field piloting experiences based on the U.S.unconventional plays.The objective of this paper is to discuss all the critical reservoir rock and fluid properties and their contribution to reservoir development through massive multi-staged hydraulic fracture networks and the EOR applications.Especially the CO_(2)and produced hydrocarbon gas injection through single well-based huff-n-puff operational constraints are discussed in detail both at micro and macro scale.

Migration and accumulation mechanisms and main controlling factors of tight oil enrichment in a continental lake basin

Based on the typical dissection of various onshore tight oil fields in China,the tight oil migration and accumulation mechanism and enrichment-controlling factors in continental lake basins are analyzed through nuclear magnetic resonance(NMR)displacement physical simulation and Lattice Boltzmann numerical simulation by using the samples of source rock,reservoir rock and crude oil.In continental lake basins,the dynamic forces driving hydrocarbon generation and expulsion of high-quality source rocks are the foundational power that determines the charging efficiency and accumulation effect of tight oil,the oil migration resistance is a key element that influences the charging efficiency and accumulation effect of tight oil,and the coupling of charging force with pore-throat resistance in tight reservoir controls the tight oil accumulation and sweet spot enrichment.The degree of tight oil enrichment in continental lake basins is controlled by four factors:source rock,reservoir pore-throat size,anisotropy of reservoir structure,and fractures.The high-quality source rocks control the near-source distribution of tight oil,reservoir physical properties and pore-throat size are positively correlated with the degree of tight oil enrichment,the anisotropy of reservoir structure reveals that the parallel migration rate is the highest,and intralayer fractures can improve the migration and accumulation efficiency and the oil saturation.

Similarity-based laboratory study of CO_(2) huff-n-puff in tight conglomerate cores

Tight conglomerate reservoirs are featured with extremely low permeability,strong heterogeneity and poor water injectivity.CO_(2) huff-n-puff has been considered a promising candidate to enhance oil recovery in tight reservoirs,owing to its advantages in reducing oil viscosity,improving mobility ratio,quickly replenishing formation pressure,and potentially achieving a miscible state.However,reliable inhouse laboratory evaluation of CO_(2) huff-n-puff in natural conglomerate cores is challenging due to the inherent high formation pressure.In this study,we put forward an equivalent method based on the similarity of the miscibility index and Grashof number to acquire a lab-controllable pressure that features the flow characteristics of CO_(2) injection in a tight conglomerate reservoir.The impacts of depletion degree,pore volume injection of CO_(2) and soaking time on ultimate oil recovery in tight cores from the Mahu conglomerate reservoir were successfully tested at an equivalent pressure.Our results showed that oil recovery decreased with increased depletion degree while exhibiting a non-monotonic tendency(first increased and then decreased)with increased CO_(2) injection volume and soaking time.The lower oil recoveries under excess CO_(2) injection and soaking time were attributed to limited CO_(2) dissolution and asphaltene precipitation.This work guides secure and reliable laboratory design of CO_(2) huff-n-puff in tight reservoirs with high formation pressure.

Quantitative investigation of nanofluid imbibition in tight oil reservoirs based on NMR technique

Nanofluids have been effective chemical additives for enhanced oil recovery(EOR)in tight oil reservoirs due to their special properties.However,oil imbibition recoveries vary for different nanofluids.The oil/water distribution in rocks during imbibition using various nanofluids was less discussed in previous studies.In this study,we systematically examined the imbibition efficiencies of various nanofluids at60℃.Furthermore,the migration of nanofluids and oil distribution in the rock pores were monitored using nuclear magnetic resonance(NMR).The nanofluids were prepared by dispersing silica nanoparticles and five different types of surfactants i.e.,anionic-nonionic,anionic,nonionic,amphoteric and cationic surfactants in deionized(DI)water.Subsequently,interfacial tension(IFT)and contact angle measurements were conducted to reveal the underlying EOR mechanisms of various nanofluids.The experimental results showed that the EOR potential of the different types of nanofluids was in the order anionic-nonionic>anionic>nonionic>amphoteric>cationic>brine.Anionic-nonionic(sodium lauryl ether sulfate(SLES))and anionic(sodium dodecyl sulfonate(SDS))nanofluids exhibited excellent capability of wettability alteration,and increased oil recovery by 27.96%and 23.08%,respectively,compared to brine.The NMR results also showed that mesopores(0.1-1μm)were the dominant developed pores in the rocks,and contributed the most to imbibition efficiency.In addition,the imbibition of nanofluids initially took place in mesopores and micropores before moving into macropores.This study provides fundamental information on the selection of nanofluids for EOR in tight oil reservoirs.The study also improved the understanding of oil/water distribution during the imbibition of the proposed nanofluids.