Propylamine hydrobromide passivated tin-based perovskites to efficient solar cells

The development of tin-based devices with low toxicity is critical for the commercial viability of perovskite solar cells.However because tin halide is a stronger Lewis acid,its crystallization rate is extremely fast,resulting in the formation of numerous defects that affect the device performance of tin-based perovskite solar cells.Herein,propylamine hydrobromide(PABr)was added to the perovskite precursor solution as an additive to passivate defects and fabricate more uniform and dense perovskite films.Because propylamine cations are too large to enter the perovskite lattices,they only exist at the grain boundary to passivate surface defects and promote crystal growth in a preferred orientation.The PABr additive raises the average short-circuit current density from 19.45 to 25.47 mA·cm^(-2)by reducing carrier recombination induced by defects.Furthermore,the device’s long-term illumination stability is improved after optimization,and the hysteresis effect is negligible.The addition of PABr results in a power conversion efficiency of 9.35%.

Potassium thiocyanate additive for PEDOT:PSS layer to fabricate efficient tin-based perovskite solar cells

The commercialized poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)(PEDOT:PSS)is usually used as hole transport layers(HTLs)in tin-based perovskite solar cells(TPSCs).However,the further development has been restricted due to the acidity that could damage the stability of TPSCs.Although the PEDOT:PSS solution can be diluted by water to decrease acidity and reduce the cost of device fabrication,the electrical conductivity will decrease obviously in diluted PEDOT:PSS solution.Herein,potassium thiocyanate(KSCN)is selected to regulate the properties of PEDOT:PSS HTLs from the diluted PEDOT:PSS aqueous solution by water with a volume ratio of 1:1 to prepare efficient TPSCs.The effect of KSCN addition on the structure and photoelectrical properties of PEDOT:PSS HTLs and TPSCs have been systematically studied.At the optimal KSCN concentration,the TPSCs based on KSCN-doped PEDOT:PSS HTLs(KSCN-PSCs)demonstrate the champion power conversion efficiency(PCE)of 8.39%,while the reference TPSCs only show a champioan PCE of 6.70%.The further analysis demonstrates that the KSCN additive increases the electrical conductivity of HTLs prepared by the diluted PEDOT:PSS solution,improves the microstructure of perovskite film,and inhibits carrier recombination in TPSCs,leading to the reduced hysteresis effect and enhanced PCE in KSCN-PSCs.This work gives a low-cost and practical strategy to develop a high-quality PEDOT:PSS HTLs from diluted PEDOT:PSS aqueous solution for efficient TPSCs.

Ligand Engineering in Tin-Based Perovskite Solar Cells

Perovskite solar cells(PSCs)have attracted aggressive attention in the photovoltaic field in light of the rapid increasing power conversion efficiency.However,their large-scale application and commercialization are limited by the toxicity issue of lead(Pb).Among all the lead-free perovskites,tin(Sn)-based perovskites have shown potential due to their low toxicity,ideal bandgap structure,high carrier mobility,and long hot carrier lifetime.Great progress of Sn-based PSCs has been realized in recent years,and the certified efficiency has now reached over 14%.Nevertheless,this record still falls far behind the theoretical calculations.This is likely due to the uncontrolled nucleation states and pronounced Sn(Ⅳ)vacancies.With insights into the methodologies resolving both issues,ligand engineering-assisted perovskite film fabrication dictates the state-of-the-art Sn-based PSCs.Herein,we summarize the role of ligand engineering during each state of film fabrication,ranging from the starting precursors to the ending fabricated bulks.The incorporation of ligands to suppress Sn~(2+)oxidation,passivate bulk defects,optimize crystal orientation,and improve stability is discussed,respectively.Finally,the remained challenges and perspectives toward advancing the performance of Sn-based PSCs are presented.We expect this review can draw a clear roadmap to facilitate Sn-based PSCs via ligand engineering.

Interfacial engineering in lead-free tin-based perovskite solar cells

Lead(Pb)-free Tin(Sn)-based perovskite solar cells(PSCs)have been favored by the community due to their low toxicity,preferable bandgaps,and great potential to achieve high power conversion efficiencies(PCEs).Interfaces engineering plays important roles in developing highly efficient Sn-based PSCs via passivation of trap defects,alignment of energy levels,and incorporation of low-dimensional Sn-based perovskites.In this review,we summarize the development of Pb-free Sn-based perovskites and their applications in devices,especially the strategies of improving the interfaces.We also provide perspectives for future research.Our aim is to help the development of new and advanced approaches to achieving high-performance environment-friendly Pb-free Sn-based PSCs.

Chiral cation promoted interfacial charge extraction for efficient tin-based perovskite solar cells

Pb-free Sn-based perovskite solar cells(PSCs) have recently made inspiring progress, and power conversion efficiency(PCE) of 14.8% has been achieved. However, due to the energy-level mismatch and poor interfacial contact between commonly used hole transport layer(i.e., poly(3,4-ethylenedioxythio phene):poly(styrene sulfonate), PEDOT:PSS) and FASnI_(3) film, it is still challenging to effectively extract holes at the interface. Owing to the p-type nature of Sn-based perovskites, the efficient hole extraction is of particular significance to improve the PCE of their solar cells. In this work, for the first time, the role of chiral cations, a-methylbenzylamine(S-/R-/rac-MBA), in promoting hole transportation of FASnI_(3)-based PSCs is demonstrated. The introduction of MBAs is found to form 2D/3D film with lowdimensional structures locating at PEDOT:PSS/FASnI_(3) interface, which facilitates the energy level alignment and efficient charge transfer at the interface. Importantly, chiral-induced spin selectivity(CISS)effect of R-MBA_(2)SnI_(4)induced by chiral R-MBA cation is found to further assist the specific interfacial transport of accumulated holes. As a result, R-MBA-based PSCs achieve decent PCE of 10.73% with much suppressed hysteresis and enhanced device stability. This work opens up a new strategy to efficiently promote the interfacial extraction of accumulated charges in working PSCs.

Recent progress in all-inorganic tin-based perovskite solar cells:a review

Recently,power conversion efficiency(PCE)of organic-inorganic hybrid perovskite solar cells(PSCs)has been improved to26.1%.However,the toxicity issue of lead still hinders the large-scale commercial production and application of lead(Pb)-based halide perovskites.Fortunately,environmentally friendly tin(Sn)-based perovskites have recently shown excellent performance.Among them,the all-inorganic Sn-based perovskites,including CsSnX_(3) and Cs_(2)SnX_(6),have better stability,more suitable bandgap,and higher charge mobility,which have attracted more attention from researchers than organic-inorganic Sn-based hybrid perovskites.Herein,we review recent research progress on all-inorganic Sn-based perovskite materials and corresponding solar cell devices.Finally,we also summarize the current challenges and future research directions for this type of PSCs.

Enhancing performance of tin-based perovskite solar cells via fused-ring electron acceptor

The performance of tin-based perovskite solar cells has been substantially hampered by voltage loss caused by energy level mismatch,charge recombination,energetic disorder,and other issues.Here,a fused-ring electron acceptor based on indacenodithiophene(IDIC)was for the first time introduced as a transition layer between a tin-based perovskite layer and a C 60 electron transport layer,leading to better matched energy levels in the device.In addition,coordination interactions between IDIC and perovskite improved the latter's crystallinity.The introduction of IDIC raised the power conversion efficiency from 8.98%to 11.5%and improved the device's stability.The decomposition mechanism of tin-based perovskite was also revealed by detecting the optical properties of perovskite microdomains through innovative integration of confocal laser scanning microscopy and photoluminescence spectroscopy.

Microwave shock motivating the Sr substitution of 2D porous GdFeO_(3) perovskite for highly active oxygen evolution

The incorporation of partial A-site substitution in perovskite oxides represents a promising strategy for precisely controlling the electronic configuration and enhancing its intrinsic catalytic activity.Conventional methods for A-site substitution typically involve prolonged high-temperature processes.While these processes promote the development of unique nanostructures with highly exposed active sites,they often result in the uncontrolled configuration of introduced elements.Herein,we present a novel approach for synthesizing two-dimensional(2D)porous GdFeO_(3) perovskite with A-site strontium(Sr)substitution utilizing microwave shock method.This technique enables precise control of the Sr content and simultaneous construction of 2D porous structures in one step,capitalizing on the advantages of rapid heating and cooling(temperature~1100 K,rate~70 K s^(-1)).The active sites of this oxygen-rich defect structure can be clearly revealed through the simulation of the electronic configuration and the comprehensive analysis of the crystal structure.For electrocatalytic oxygen evolution reaction application,the synthesized 2D porous Gd_(0.8)Sr_(0.2)FeO_(3) electrocatalyst exhibits an exceptional overpotential of 294 mV at a current density of 10 mA cm^(-2)and a small Tafel slope of 55.85 mV dec^(-1)in alkaline electrolytes.This study offers a fresh perspective on designing crystal configurations and the construction of nanostructures in perovskite.

Boosting oxygen reduction activity and CO_(2) resistance on bismuth ferrite-based perovskite cathode for low-temperature solid oxide fuel cells below 600℃

Developing efficient and stable cathodes for low-temperature solid oxide fuel cells(LT-SOFCs) is of great importance for the practical commercialization.Herein,we propose a series of Sm-modified Bi_(0.7-x)Sm_xSr_(0.3)FeO_(3-δ) perovskites as highly-active catalysts for LT-SOFCs.Sm doping can significantly enhance the electrocata lytic activity and chemical stability of cathode.At 600℃,Bi_(0.675)Sm_(0.025)Sr_(0.3)FeO_(3-δ)(BSSF25) cathode has been found to be the optimum composition with a polarization resistance of 0.098 Ω cm^2,which is only around 22.8% of Bi_(0.7)Sr_(0.3)FeO_(3-δ)(BSF).A full cell utilizing BSSF25 displays an exceptional output density of 790 mW cm^(-2),which can operate continuously over100 h without obvious degradation.The remarkable electrochemical performance observed can be attributed to the improved O_(2) transport kinetics,superior surface oxygen adsorption capacity,as well as O_(2)p band centers in close proximity to the Fermi level.Moreover,larger average bonding energy(ABE) and the presence of highly acidic Bi,Sm,and Fe ions restrict the adsorption of CO_(2) on the cathode surface,resulting in excellent CO_(2) resistivity.This work provides valuable guidance for systematic design of efficient and durable catalysts for LT-SOFCs.

Constructing low-dimensional perovskite network to assist efficient and stable perovskite solar cells

The use of low-dimensional(LD)perovskite materials is crucial for achieving high-performance perovskite solar cells(PSCs).However,LD perovskite films fabricated by conventional approaches give rise to full coverage of the underlying 3D perovskite films,which inevitably hinders the transport of charge carriers at the interface of PSCs.Here,we designed and fabricated LD perovskite structure that forms net-like morphology on top of the underlying three-dimensional(3D)perovskite bulk film.The net-like LD perovskite not only reduced the surface defects of 3D perovskite film,but also provided channels for the vertical transport of charge carriers,effectively enhancing the interfacial charge transfer at the LD/3D hetero-interface.The net-like morphological design comprising LD perovskite effectively resolves the contradiction between interfacial defect passivation and carrier extraction across the hetero-interfaces.Furthermore,the net-like LD perovskite morphology can enhance the stability of the underlying 3D perovskite film,which is attributed to the hydrophobic nature of LD perovskite.As a result,the net-like LD perovskite film morphology assists PSCs in achieving an excellent power conversion efficiency of up to 24.6%with over 1000 h long-term operational stability.

Stabilizing perovskite precursors with the reductive natural amino acid for printable mesoscopic perovskite solar cells

Solution processability significantly advances the development of highly-efficient perovskite solar cells.However,the precursor solution tends to undergo irreversible degradation reactions,impairing the device performance and reproducibility.Here,we utilize a reductive natural amino acid,Nacetylcysteine(NALC),to stabilize the precursor solution for printable carbon-based hole-conductorfree mesoscopic perovskite solar cells.We find that I_(2) can be generated in the aged solution containing methylammonium iodide(MI) in an inert atmosphere and speed up the MA-FA^(+)(formamidinium) reaction which produces large-size cations and hinders the formation of perovskite phase.NALC effectively stabilizes the precursor via its sulfhydryl group which reduces I_(2) back to I^(-)and provides H^(+).The NALC-stabilized precursor which is aged for 1440 h leads to devices with a power conversion efficiency equivalent to 98% of that for devices prepared with the fresh precursor.Furthermore,NALC improves the device power conversion efficiency from 16.16% to 18.41% along with enhanced stability under atmospheric conditions by modifying grain boundaries in perovskite films and reducing associated defects.

Investigation of an electrode-driven hydrogen plasma method for in situ cleaning of tin-based contamination

To prolong the service life of optics,the feasibility of in situ cleaning of the multilayer mirror(MLM)of tin and its oxidized contamination was investigated using hydrogen plasma at different power levels.Granular tin-based contamination consisting of micro-and macroparticles was deposited on silicon via physical vapor deposition(PVD).The electrodedriven hydrogen plasma at different power levels was systematically diagnosed using a Langmuir probe and a retarding field ion energy analyzer(RFEA).Moreover,the magnitude of the self-biasing voltage was measured at different power levels,and the peak ion energy was corrected for the difference between the RFEA measurements and the self-biasing voltage(E_(RFEA)-eV_(self)).XPS analysis of O 1s and Sn 3d peaks demonstrated the chemical reduction process after 1 W cleaning.Analysis of surface and cross-section morphology revealed that holes emerged on the upper part of the macroparticles while its bottom remained smooth.Hills and folds appeared on the upper part of the microparticles,confirming the top-down cleaning mode with hydrogen plasma.This study provides an in situ electrode-driven hydrogen plasma etching process for tin-based contamination and will provide meaningful guidance for understanding the chemical mechanism of reduction and etching.

Boosting MA-based two-dimensional Ruddlesden-Popper perovskite solar cells by incorporating a binary spacer

Two-dimensional Ruddlesden-Popper(2DRP)perovskite exhibits excellent stability in perovskite solar cells(PSCs)due to introducing hydrophobic long-chain organic spacers.However,the poor charge transporting property of bulky organic cation spacers limits the performance of 2DRP PSCs.Inspired by the Asite cation alloying strategy in 3D perovskites,2DRP perovskites with a binary spacer can promote charge transporting compared to the unary spacer counterparts.Herein,the superior MA-based 2DRP perovskite films with a binary spacer,including 3-guanidinopropanoic acid(GPA)and 4-fluorophenethylamine(FPEA)are realized.These films(GPA_(0.85)FPEA_(0.15))_(2)MA_(4)Pb_5I_(16)show good morphology,large grain size,decreased trap state density,and preferential orientation of the as-prepared film.Accordingly,the present 2DRP-based PSC with the binary spacer achieves a remarkable efficiency of 18.37%with a V_(OC)of1.15 V,a J_(SC)of 20.13 mA cm^(-2),and an FF of 79.23%.To our knowledge,the PCE value should be the highest for binary spacer MA-based 2DRP(n≤5)PSCs to date.Importantly,owing to the hydrophobic fluorine group of FPEA and the enhanced interlayer interaction by FPEA,the unencapsulated 2DRP PSCs based on binary spacers exhibit much excellent humidity stability and thermal stability than the unary spacer counterparts.

Efficient and Stable Inverted Perovskite Solar Modules Enabled by Solid-Liquid Two-Step Film Formation

A considerable efficiency gap exists between large-area perovskite solar modules and small-area perovskite solar cells.The control of forming uniform and large-area film and perovskite crystallization is still the main obstacle restricting the efficiency of PSMs.In this work,we adopted a solid-liquid two-step film formation technique,which involved the evaporation of a lead iodide film and blade coating of an organic ammonium halide solution to prepare perovskite films.This method possesses the advantages of integrating vapor deposition and solution methods,which could apply to substrates with different roughness and avoid using toxic solvents to achieve a more uniform,large-area perovskite film.Furthermore,modification of the NiO_(x)/perovskite buried interface and introduction of Urea additives were utilized to reduce interface recombination and regulate perovskite crystallization.As a result,a large-area perovskite film possessing larger grains,fewer pinholes,and reduced defects could be achieved.The inverted PSM with an active area of 61.56 cm^(2)(10×10 cm^(2)substrate)achieved a champion power conversion efficiency of 20.56%and significantly improved stability.This method suggests an innovative approach to resolving the uniformity issue associated with large-area film fabrication.

Pressure-Induced Distinct Self-Trapped Exciton Emission in Sb^(3+)-Doped Cs_(2)NaInCl_(6)Double Perovskite

The Cs_(2)NaInCl_(6) double perovskite is one of the most promising lead-free perovskites due to its exceptional stability and straightforward synthesis.However,it faces challenges related to inefficient photoluminescence.Doping and high pressure are employed to tailor the optical properties of Cs_(2)NaInCl_(6).Herein,Sb^(3+)doped Cs_(2)NaInCl_(6)(Sb^(3+):Cs_(2)NaInCl_(6)) was synthesized and it exhibits blue emission with a photoluminescence quantum yield of up to 37.3%.Further,by employing pressure tuning,a blue stable emission under a very wide range from 2.7 GPa to 9.8 GPa is realized in Sb^(3+):Cs_(2)NaInCl_(6).Subsequently,the emission intensity of Sb^(3+):Cs_(2)NaInCl_(6) experiences a significant increase(3.3 times)at 19.0 GPa.It is revealed that the pressure-induced distinct emissions can be attributed to the carrier self-trapping and detrapping between Cs_(2)NaInCl_(6) and Sb^(3+).Notably,the lattice compression in the cubic phase inevitably modifies the band gap of Sb^(3+):Cs_(2)NaInCl_(6).Our findings provide valuable insights into effects of the high pressure in further boosting unique emission characteristics but also offer promising opportunities for development of doped double perovskites with enhanced optical functionalities.

Effect of drying methods on perovskite films and solar cells

The high efficiency,solution processibility,and flexibility of perovskite solar cells make them promising candidates for the photovoltaic industry[1−8].The deposition method is one of the most critical factors that affect the performance of perovskite films.Various deposition methods have been developed to make perovskite films,including spin-coating,slotdie coating.

Accelerating the evaluation of operational lifetimes of perovskite solar cells and modules

Compared with the power conversion efficicency,the operational stability of perovskite solar cells(PsCs)remains a major challenge hampering its commercialization.However,conducting a light soaking test under 1 sun illumination to get a long lifetime is time-consuming and experimentally inefficient.Here,we report an accelerated stability test protocol by aging PsCs under high-intensity light illumination to accelerate the evaluation of their operation stability.It is found that the efficiency degradation rate of a typical inverted PsC is almost linearly dependent on the light intensity within the range of 1 to 4 suns regardless of the encapsulations.The results prove that it can save the light-soaking time by at least 4 times to predict the operation lifetime on the basis of the equivalent light irradiation dose.

Chemical vapor deposition for perovskite solar cells and modules

Metal halide perovskites are promising materials for solar cells because of high power conversion efficiency(PCE),tun-able bandgap,high defect tolerance,long carrier diffusion length,and low-cost fabrication[1-7].The PCE for perovskite solar cells(PSCs)reaches 26.14%for single-junction cells,29.1%for perovskite/perovskite tandem cells and 33.9%for perovskite/silicon tandem cells,being comparable to that for silicon and other thin-film solar cells[8-10].Perovskite solar cells have been made by solution methods including spin-coat-ing,blade coating and printing[11,12].

Textured Perovskite/Silicon Tandem Solar Cells Achieving Over 30% Efficiency Promoted by 4-Fluorobenzylamine Hydroiodide

Monolithic textured perovskite/silicon tandem solar cells(TSCs)are expected to achieve maximum light capture at the lowest cost,potentially exhibiting the best power conversion efficiency.However,it is challenging to fabricate high-quality perovskite films and preferred crystal orientation on commercially textured silicon substrates with micrometersize pyramids.Here,we introduced a bulky organic molecule(4-fluorobenzylamine hydroiodide(F-PMAI))as a perovskite additive.It is found that F-PMAI can retard the crystallization process of perovskite film through hydrogen bond interaction between F^(−)and FA^(+)and reduce(111)facet surface energy due to enhanced adsorption energy of F-PMAI on the(111)facet.Besides,the bulky molecular is extruded to the bottom and top of perovskite film after crystal growth,which can passivate interface defects through strong interaction between F-PMA+and undercoordinated Pb^(2+)/I^(−).As a result,the additive facilitates the formation of large perovskite grains and(111)preferred orientation with a reduced trap-state density,thereby promoting charge carrier transportation,and enhancing device performance and stability.The perovskite/silicon TSCs achieved a champion efficiency of 30.05%based on a silicon thin film tunneling junction.In addition,the devices exhibit excellent longterm thermal and light stability without encapsulation.This work provides an effective strategy for achieving efficient and stable TSCs.

Author Correction: ITO-free silicon-integrated perovskite electrochemical cell for light-emission and light-detection

Correction to:Opto-Electronic Advances https://doi.org/10.29026/oea.2023.220154 published online 26 April 2023 After the publication of this article1,it was brought to our attention that calculations of the PeLEC device elec-troluminescent(EL)efficiency contained a mistake,leading to an inaccurate quantity value.The device’s maxim-um EL efficiency constitutes not‘~120 klm/W’but‘4.3 lm/W’instead.Correction details are listed below.