Laser powder bed fusion(L-PBF)of Mg alloys has provided tremendous opportunities for customized production of aeronautical and medical parts.Layer thickness(LT)is of great significance to the L-PBF process but has not...Laser powder bed fusion(L-PBF)of Mg alloys has provided tremendous opportunities for customized production of aeronautical and medical parts.Layer thickness(LT)is of great significance to the L-PBF process but has not been studied for Mg alloys.In this study,WE43 Mg alloy bulk cubes,porous scaffolds,and thin walls with layer thicknesses of 10,20,30,and 40μm were fabricated.The required laser energy input increased with increasing layer thickness and was different for the bulk cubes and porous scaffolds.Porosity tended to occur at the connection joints in porous scaffolds for LT40 and could be eliminated by reducing the laser energy input.For thin wall parts,a large overhang angle or a small wall thickness resulted in porosity when a large layer thicknesses was used,and the porosity disappeared by reducing the layer thickness or laser energy input.A deeper keyhole penetration was found in all occasions with porosity,explaining the influence of layer thickness,geometrical structure,and laser energy input on the porosity.All the samples achieved a high fusion quality with a relative density of over 99.5%using the optimized laser energy input.The increased layer thickness resulted to more precipitation phases,finer grain sizes and decreased grain texture.With the similar high fusion quality,the tensile strength and elongation of bulk samples were significantly improved from 257 MPa and 1.41%with the 10μm layer to 287 MPa and 15.12%with the 40μm layer,in accordance with the microstructural change.The effect of layer thickness on the compressive properties of porous scaffolds was limited.However,the corrosion rate of bulk samples accelerated with increasing the layer thickness,mainly attributed to the increased number of precipitation phases.展开更多
The poor corrosion and wear resistances of Mg alloys seriously limit their potential applications in various industries.The conventional epoxy coating easily forms many intrinsic defects during the solidification proc...The poor corrosion and wear resistances of Mg alloys seriously limit their potential applications in various industries.The conventional epoxy coating easily forms many intrinsic defects during the solidification process,which cannot provide sufficient protection.In the current study,we design a double-layer epoxy composite coating on Mg alloy with enhanced anti-corrosion/wear properties,via the spin-assisted assembly technique.The outer layer is functionalized graphene(FG)in waterborne epoxy resin(WEP)and the inner layer is Ce-based conversion(Ce)film.The FG sheets can be homogeneously dispersed within the epoxy matrix to fill the intrinsic defects and improve the barrier capability.The Ce film connects the outer layer with the substrate,showing the transition effect.The corrosion rate of Ce/WEP/FG composite coating is 2131 times lower than that of bare Mg alloy,and the wear rate is decreased by~90%.The improved corrosion resistance is attributed to the labyrinth effect(hindering the penetration of corrosive medium)and the obstruction of galvanic coupling behavior.The synergistic effect derived from the FG sheet and blocking layer exhibits great potential in realizing the improvement of multi-functional integration,which will open up a new avenue for the development of novel composite protection coatings of Mg alloys.展开更多
The high corrosion rate of magnesium and its alloys in chloride-containing solution significantly reduces the potential of this material for diverse applications.Therefore,the formation of a smart protective coating w...The high corrosion rate of magnesium and its alloys in chloride-containing solution significantly reduces the potential of this material for diverse applications.Therefore,the formation of a smart protective coating was achieved in this work to prevent degradation of the MA8 magnesium alloy.A porous ceramic-like matrix was obtained on the material by plasma electrolytic oxidation(PEO).Further surface functionalization was performed using layered double hydroxides(LDH) served as nanocontainers for the corrosion inhibitor.Several methods of LDH intercalation with benzotriazole(BTA) were proposed.The composition and morphology of the formed coating were studied using SEM-EDX analysis,XRD,XPS,and Raman microspectroscopy.The corrosion behavior of the coated samples was evaluated using electrochemical impedance spectroscopy and potentiodynamic polarization.The corrosion rate was estimated using volumetry and gravimetry methods.The formed composite coating provides the Mg alloy with the lowest corrosion activity(|Z|_(f)=0.1 Hz)=8.48·10^(5) Ω·cm^(2),I_(c)=1.4·10^(-8)A/cm^(2),P_(H)=0.21 mm/year) and improves the protective properties of the PEO-coated sample(|Z|_(f)=0.1 Hz)=8.37·10^(3) Ω·cm^(2),I_(c)=4.1·10^(-7)A/cm^(2),P_(H)=0.31 mm/year).The realization of the self-healing effect of the inhibitor-containing LDH/PEO-coated system was studied using localized electrochemical methods(SVET and SIET) with two artificial defects on the surface.A mechanism involving three stages for the active corrosion protection of the alloy was proposed.These findings contribute to the follow-up work of developing modified LDH/PEO-based structures that promote the Mg alloy with high corrosion resistance,superior electrochemical performance for applications in various fields of industry and medicine.展开更多
Lithium metal batteries represent promising candidates for high-energy-density batteries, however, many challenges must still be overcome,e.g., interface instability and dendrite growth. In this work, nano silica aero...Lithium metal batteries represent promising candidates for high-energy-density batteries, however, many challenges must still be overcome,e.g., interface instability and dendrite growth. In this work, nano silica aerogel was employed to generate a hybrid film with high lithium ion conductivity(0.6 mS cm^(-1)at room temperature) via an in situ crosslinking reaction. TOF-SIMS profile analysis has revealed conversion mechanism of hybrid film to Li–Si alloy/Li F biphasic interface layer, suggesting that the Li–Si alloy and Li F-rich interface layer promoted rapid Li+transport and shielded the Li anodes from corrosive reactions with electrolyte-derived products. When coupled with nickel-cobalt-manganese-based cathodes, the batteries achieve outstanding capacity retention over 1000 cycles at 1 C. Additionally the developed film coated on Li enabled high coulombic efficiency(99.5%) after long-term cycling when coupled with S cathodes. Overall, the results presented herein confirm an effective strategy for the development of high-energy batteries.展开更多
A novel inorganic-organic layer with outstanding corrosion resistance in a 3.5wt.% NaCl solution was fabricated by taking advantage of the unique interactions between coumarin (COM) molecules and the porous layer form...A novel inorganic-organic layer with outstanding corrosion resistance in a 3.5wt.% NaCl solution was fabricated by taking advantage of the unique interactions between coumarin (COM) molecules and the porous layer formed on Mg alloy. To achieve this aim, the AZ31 Mg alloy coated via microarc oxidation (MAO) coating was placed in an ethanolic solution of COM for 6 and 12 h at 25 ℃. By reducing the surface area exposed to the corrosive species, the donor-acceptor complexes produced by the particular interactions between the COM and MAO surface would successfully prevent the corrosion of Mg alloy substrate. The MAO layer would provide the ideal sites for the charge-transfer-induced physical and chemical locking, leading to uneven organic layer nucleation and crystal growth with a thatch-like structure. To evaluate the formation mechanism of such hybrid composites and highlight the key bonding modes between the COM and MAO, theoretical simulations were conducted.展开更多
Layered double hydroxide(LDH)coatings on magnesium(Mg)alloys shine brightly in the field of corrosion protection because of their special ion-exchange function.State-of-the-art steam coating as a type of LDH film prep...Layered double hydroxide(LDH)coatings on magnesium(Mg)alloys shine brightly in the field of corrosion protection because of their special ion-exchange function.State-of-the-art steam coating as a type of LDH film preparation technique has emerged in recent years because only pure water is required as the steam source and its environmentally friendly LDH coating fits the current need for green development.Moreover,this coating can effectively inhibit the corrosion of the Mg alloy substrate due to the chemical bonding between the coating and the Mg alloy substrate.This review systematically explains cutting-edge advancements in the growth mechanism and corrosion behavior of LDH steam coatings,and analyzes the advantages and limitations of the steam-coating method.The influencing factors including pressure,CO_(2)/CO_(3)^(2-),aluminum content of the substrate alloy,solution type,and acid-pickling pretreatment,as well as the post-treatment of steam-coating defects,are comprehensively elucidated,providing new insights into the development of the in situ steam-coating technique.Finally,existing issues and future prospects are discussed to further accelerate the widespread application of Mg alloys.展开更多
Solid polymer electrolytes(SPEs)are urgently required to achieve practical solid-state lithium metal batteries(LMBs)and lithium-ion batteries(LIBs),Herein,we proposed a mechanism for modulating interfacial conduction ...Solid polymer electrolytes(SPEs)are urgently required to achieve practical solid-state lithium metal batteries(LMBs)and lithium-ion batteries(LIBs),Herein,we proposed a mechanism for modulating interfacial conduction and anode interfaces in high-concentration SPEs by LiDFBOP.Optimized electrolyte exhibits superior ionic conductivity and remarkable interface compatibility with salt-rich clusters:(1)polymer-plastic crystal electrolyte(P-PCE,TPU-SN matrix)dissociates ion pairs to facilitate Li+transport in the electrolyte and regulates Li^(+)diffusion in the SEI.The crosslinking structure of the matrix compensates for the loss of mechanical strength at high-salt concentrations;(2)dual-anion TFSI^(-)_(n)-DFBOP^(-)_(m)in the Li^(+)solvation sheath facilitates facile Li^(+)desolvation and formation of salt-rich clusters and is conducive to the formation of Li conductive segments of TPU-SN matrix;(3)theoretical calculations indicate that the decomposition products of LiDFBOP form SEI with lower binding energy with LiF in the SN system,thereby enhancing the interfacial electrochemical redox kinetics of SPE and creating a solid interface SEI layer rich in LiF.As a result,the optimized electrolyte exhibits an excellent ionic conductivity of9.31×10^(-4)S cm^(-1)at 30℃and a broadened electrochemical stability up to 4.73 V.The designed electrolyte effectively prevents the formation of Li dendrites in Li symmetric cells for over 6500 h at0.1 mA cm^(-2).The specific Li-Si alloy-solid state half-cell capacity shows 711.6 mAh g^(-1)after 60 cycles at 0.3 A g^(-1).Excellent rate performance and cycling stability are achieved for these solid-state batteries with Li-Si alloy anodes and NCM 811 cathodes.NCM 811‖Prelithiated silicon-based anode solid-state cell delivers a discharge capacity of 195.55 mAh g^(-1)and a capacity retention of 97.8%after 120 cycles.NCM 811‖Li solid-state cell also delivers capacity retention of 84.2%after 450 cycles.展开更多
The self-assembly of hybrid inorganic-organic materials on stationary platforms plays a critical role in improving their structural stability and wide usability.In this work,a novel two-step hydrothermal approach is p...The self-assembly of hybrid inorganic-organic materials on stationary platforms plays a critical role in improving their structural stability and wide usability.In this work,a novel two-step hydrothermal approach is proposed for synthesizing stable and advanced hybrid coatings on metal-oxide platforms through the surface modification of layered double hydroxide(LDH)films using novel metal-organic frameworks(MOFs).Initially,Mg-Al LDH nanocontainers,grown on a magnesium oxide layer produced through plasma electrolytic oxidation(PEO)of AZ31 Mg alloy substrate,were intercalated with cobalt via an oxidation route,providing the metallic coordination center for the MOF formation.In the subsequent step,a pioneering technique is introduced,utilizing tryptophan as the organic linker for the first time at a pH of 10.The self-assembly of cobalt-tryptophan complex,driven by the strong bonding between electrophilic sites of monomers and nucleophilic sites,facilitated the formation of a MOF network having a cloud-like structure on the surface of MgAl LDH's film.The resulting MOF-LDH encapsulation containers demonstrate exceptional electrochemical stability when exposed to a 3.5 wt.%NaCl solution,surpassing the performance of PEO and pure LDH coatings.This enhanced stability is attributed to the development of a dense top layer and a stable composition within the self-assembled MOF,effectively sealing flaws and preventing the infiltration of corrosive ions into the underlying metallic substrate.The formation mechanism of MOFs on LDH galleries is investigated using density functional theory calculations.展开更多
Effects of alloy elements on the microstructure and crack resistance of Fe-C-Cr weld surfacing layer were investigated. The results show that microstructures of the layer mainly consist of carbides and austenite matri...Effects of alloy elements on the microstructure and crack resistance of Fe-C-Cr weld surfacing layer were investigated. The results show that microstructures of the layer mainly consist of carbides and austenite matrix. Increasing C and Cr contents impair the crack resistance of the layer due to increased amount of brittle carbides. The addition of Ni, Nb or Mo improves the crack resistance of Fe-C-Cr weld surfacing layer by increasing the amount of austenite and forming fine NbC or M 7C 3 carbides in the layer. But, the excessive Nb (>2.50wt%) or Mo (>1.88wt%) impairs the crack resistance of the layer, which has relation with increased carbides or carbide coarsening and austenite matrix solid solution strengthening. The proper combination of C, Cr, Ni, Nb and Mo can further improve not only the crack resistance of Fe-C-Cr weld surfacing layer but also the erosion resistance as a result of fine NbC and M 7C 3 carbides distributing uniformly in austenite matrix. The optimal layer compositions are 3.05wt%C, 20.58wt%Cr, 1.75wt%Ni, 2.00wt%Nb and 1.88wt%Mo.展开更多
Effects of alloying elements on microstructure and erosion resistance of Fe-C-Cr weld surfacing layer have been studied. The experimental results show that increasing C and Cr content favors improving the erosion resi...Effects of alloying elements on microstructure and erosion resistance of Fe-C-Cr weld surfacing layer have been studied. The experimental results show that increasing C and Cr content favors improving the erosion resistance of the layer, and the excessive C and Cr result in decreasing the erosion resistance at 90 deg. erosion. That Mo, Nb or Ti improves the erosion resistance of Fe-C-Cr weld surfacing layer is mainly attributed to increasing the amount of M7C3 and forming fine NbC or TiC in austenite matrix, but the excessive Mo, Nb or Ti is unfavorable. The addition of Mo, Nb and Ti in proper combination possesses stronger effect on improving the erosion resistance and the erosion resistance (εA) of Fe-C-Cr weld surfacing layer with fine NbC, TiC and M7C3 distributing uniformly in austenite matrix obviously increases to 2.81 at 15 deg. erosion and 2.88 at 90 deg. erosion when the layer composition is 3.05C, 20.58Cr, 1.88Mo, 2.00Nb and 1.05Ti (in wt pct).展开更多
A simple chemical method was developed for inducing bioactivity on NiTi alloys (50 at. pct by Ni/Ti). A layer of calcium phosphate was deposited on the surface to improve biocompatibility of the alloy. NiTi alloys wer...A simple chemical method was developed for inducing bioactivity on NiTi alloys (50 at. pct by Ni/Ti). A layer of calcium phosphate was deposited on the surface to improve biocompatibility of the alloy. NiTi alloys were first etched in HNO3 aqueous solution, and then treated with boiling diluted NaOH solution. A rough surface was created and a thin TiO2 layer was formed on the surface. Pre-calcification was then introduced by immersing the treated NiTi alloys in supersaturated Na2HPO4 solution and supersaturated Ca(OH)2 solution in turn before calcification in simulated body fluid (SBF). A dense and uniform bonelike calcium phosphate (Ca-P) bioactive layer was formed on the surfaces of the specimen, which would improve their biocompatibility. Morphology and element analysis on NiTi surfaces during the treatments were investigated in detail by means of environment scanning electron microscopy (ESEM), energy dispersion X-ray spectroscopy (EDXS), and X-ray diffraction (XRD).展开更多
The Multi layer coating of Ni60 alloy was got by multi layer laser cladding. The height of the coating was about 12mm and the wall of the coating was perpendicular to the base. The microstructure of the coating was ...The Multi layer coating of Ni60 alloy was got by multi layer laser cladding. The height of the coating was about 12mm and the wall of the coating was perpendicular to the base. The microstructure of the coating was made up of fine dendrite. The conjunction between layers was good.展开更多
The MAO (Micro-Arc Oxidation) process is applied to a eutectic Al-Si alloy(Al-12.0 percent Si-l.0 percent Cu-0.9 percent Mg (mass fraction)). The oxide ceramic layer wasfabricated with about 220 mum thickness and 3000...The MAO (Micro-Arc Oxidation) process is applied to a eutectic Al-Si alloy(Al-12.0 percent Si-l.0 percent Cu-0.9 percent Mg (mass fraction)). The oxide ceramic layer wasfabricated with about 220 mum thickness and 3000 Hv micro-hardness. By XRD (X-ray diffractometry)and DSC (differential scanning calorimetry) analyses, the oxide layer consists of amorphous Al_2O_3,which is distinct from the results reported by the other researchers. The SEM photographs of suchlayer show that the layer is fixed tightly on the substrate alloy. So this alloy can he used in thehigh temperature and friction environment alter it is treated with such process.展开更多
For high corrosion resistance and extensively modified biodegradable Mg-based alloys and composites for bone implants,a new Mgbased matrix model prepared by powder metallurgy is discussed and developed.In this researc...For high corrosion resistance and extensively modified biodegradable Mg-based alloys and composites for bone implants,a new Mgbased matrix model prepared by powder metallurgy is discussed and developed.In this research,Mg-5 wt.%Zn alloys were selected as a case.And they were impacted by hot extrusion and aging treatments to construct microstructure with different characteristics.Their selfforming corrosion product layer in Ringer’s solution,biodegradable behavior and corrosion mechanism were minutely investigated by in vitro degradation,electrochemical corrosion and cytocompatibility.The results demonstrated the extruded Mg-5 wt.%Zn alloy aged for 96 h showed high corrosion resistance,good biocompatibility for L929 and excellent ability of maintaining sample integrity during the immersion.Significantly,the alloy showed fine-grain microstructure and uniform distributed hundred nano-sized second phases,which promoted the formation of the uniform and smooth corrosion product layer at the beginning of immersion.The corrosion product layer was more stable in chloride containing aqueous solution and could be directly formed and repaired quickly,which effectively protected the matrix from further corrosion.In addition,an ideal model of Mg-based matrix for bone tissue engineering was tried to presume and propose by discussing the causal relationship between microstructure and bio-corrosion process.展开更多
After tempering treatment at different conditions, the tempering stability of Fe-base hardfacing layer containing RE and multiple alloying was investigated. The results show that after heat preservation at 560 ℃ and ...After tempering treatment at different conditions, the tempering stability of Fe-base hardfacing layer containing RE and multiple alloying was investigated. The results show that after heat preservation at 560 ℃ and tempering for 4 h the hardness value of Fe-base hardfacing layer containing RE and multiple alloying can reach HRC57; By repeatedly heating circle 700 ℃17 ℃ for 150 times, the hardness value of Fe-base hardfacing layer can reach HRC43, tempering stability is higher and causes the secondary hardening phenomenon. Reasons for higher tempering stability of Fe-base hardfacing layer were analyzed by means of metallographic, XRD, TEM and EDS.展开更多
In this study,an environment-friendly layered double hydroxide(LDH)film has been deposited on Mg Ca alloy by a two-step technique.To improve the chemical conversion technique and control the film properties,batch stud...In this study,an environment-friendly layered double hydroxide(LDH)film has been deposited on Mg Ca alloy by a two-step technique.To improve the chemical conversion technique and control the film properties,batch studies have been carried out to address various process parameters such as pH value,treatment temperature and immersion time.The chemical composition was determined by X-ray diffractometry and energy dispersive X-ray spectroscopy.The morphology was characterized by scanning electron microscopy.The corrosion resistance of the samples with various films was compared by polarization curves and immersion test.It is found that the transformation duration of Mg-Fe LDH is long.Too high pH value and temperature has harmful effect on the purity of the film composition.The corrosion resistance of the films formed at low value of pH or high temperature or short treatment time is deteriorative.The optimum process is as follows:the sample is first immersed in the solution containing Fe^(3+)/HCO_(3)^-/CO_(3)^(2-)with a pH value of 5 at a temperature of 55℃for 1 h to form a precursor film,and then this precursor film is immersed into the solution containing Fe^(3+)/HCO_(3)^-/CO_(3)^(2-)with a pH of 11 at 55℃for 24 h to obtain the Mg-Fe LDH conversion film.展开更多
Dissimilar metals TIG welding-brazing of aluminum alloy and non-coated stainless steel was investigated. The resultant joint was characterized in order to identify the phases and the brittle intermetallic compounds (...Dissimilar metals TIG welding-brazing of aluminum alloy and non-coated stainless steel was investigated. The resultant joint was characterized in order to identify the phases and the brittle intermetallic compounds (IMCs) in the interracial layer by optical metalloscope (OM), scanning electron microscopy (SEM) and energy dispersive spectrometer ( EDS) , and the cracked joint was analyzed in order to understand the cracking mechanism of the joint. The results show that the microfusion of the stainless steel can improve the wetting and spreading of liquid aluminum base filler metal on the steel suuface and the melted steel accelerates the formation of mass of brittle IMCs in the interracial layer, which causes the joint cracking badly. The whole interfacial layer is 5 -7 μm thick and comprises approximately 5μm-thickness reaction layer in aluminum side and about 2 μm-thickness diffusion layer in steel side. The stable Al-rich IMCs are formed in the interfacial layer and the phases transfer from ( Al + FeAl3 ) in aluminum side to ( FeAl3 + Fe2Al5 ) and ( α-Fe + FeAl) in steel side.展开更多
8-hydroxyquinoline(8-HQ)intercalated layered double hydroxides(LDH)film as underlayer and sol-gel layer was combined for active corrosion protection of the AM60B magnesium alloy.The LDH,LDH/sol-gel,and LDH@HQ/sol-gel ...8-hydroxyquinoline(8-HQ)intercalated layered double hydroxides(LDH)film as underlayer and sol-gel layer was combined for active corrosion protection of the AM60B magnesium alloy.The LDH,LDH/sol-gel,and LDH@HQ/sol-gel coatings were analyzed using the scanning electron microscopy(SEM),field emission scanning electron microscopy(FESEM),energy dispersive X-ray spectroscopy(EDS),X-ray diffraction(XRD),atomic force microscopy(AFM),and electrochemical impedance spectroscopy(EIS)methods.The SEM images showed that the surface was entirely coated by the LDH film composed of vertically-grown nanosheets.The same morphology was observed for the LDH/sol-gel and LDH@HQ/sol-gel coatings.Also,almost the same topography was observed for both composite coatings except that the LDH@HQ/sol-gel coating had relatively higher surface roughness.Although the LDH film had the same impedance behavior as the alloy sample in 3.5wt%NaCl solution,its corrosion resistance was much higher,which could be due to its barrier properties as well as to the trap-ping of the chloride ions.Similar to the LDH film,the corrosion resistance of the LDH/sol-gel composite diminished with increasing the ex-posure time.However,its values were much higher than that of the LDH film,which was mainly related to the sealing of the solution path-ways.The LDH@HQ/sol-gel composite showed much better anti-corrosion properties than the LDH/sol-gel coating due to the adsorption of the 8-HQ on the damaged areas through the complexation.展开更多
Composite,diffusive titanium nitride layers formed on a titanium and aluminum sub-layer were produced on the AZ91D magnesium alloy.The layers were obtained using a hybrid method which combined the PVD processes with t...Composite,diffusive titanium nitride layers formed on a titanium and aluminum sub-layer were produced on the AZ91D magnesium alloy.The layers were obtained using a hybrid method which combined the PVD processes with the final sealing by a hydrothermal treatment.The microstructure,resistance to corrosion,mechanical damage,and frictional wear of the layers were examined.The properties of the AZ91D alloy covered with these layers were compared with those of the untreated alloy and of some engineering materials such as 316L stainless steel,100Cr6 bearing steel,and the AZ91D alloy subjected to commercial anodizing.It has been found that the composite diffusive nitride layer produced on the AZ91D alloy and then sealed by the hydrothermal treatment ensures the corrosion resistance comparable with that of 316L stainless steel.The layers are characterized by higher electrochemical durability which is due to the surface being overbuilt with the titanium oxides formed,as shown by the XPS examinations,from titanium nitride during the hydrothermal treatment.The composite titanium nitride layers exhibit high resistance to mechanical damage and wear,including frictional wear which is comparable with that of 100Cr6 bearing steel.The performance properties of the AZ91D magnesium alloy covered with the composite titanium nitride coating are substantially superior to those of the alloy subjected to commercial anodizing which is the dominant technique employed in industrial practice.展开更多
基金funded by the National Key Research and Development Program of China(2018YFE0104200)National Natural Science Foundation of China(51875310,52175274,82172065)Tsinghua Precision Medicine Foundation.
文摘Laser powder bed fusion(L-PBF)of Mg alloys has provided tremendous opportunities for customized production of aeronautical and medical parts.Layer thickness(LT)is of great significance to the L-PBF process but has not been studied for Mg alloys.In this study,WE43 Mg alloy bulk cubes,porous scaffolds,and thin walls with layer thicknesses of 10,20,30,and 40μm were fabricated.The required laser energy input increased with increasing layer thickness and was different for the bulk cubes and porous scaffolds.Porosity tended to occur at the connection joints in porous scaffolds for LT40 and could be eliminated by reducing the laser energy input.For thin wall parts,a large overhang angle or a small wall thickness resulted in porosity when a large layer thicknesses was used,and the porosity disappeared by reducing the layer thickness or laser energy input.A deeper keyhole penetration was found in all occasions with porosity,explaining the influence of layer thickness,geometrical structure,and laser energy input on the porosity.All the samples achieved a high fusion quality with a relative density of over 99.5%using the optimized laser energy input.The increased layer thickness resulted to more precipitation phases,finer grain sizes and decreased grain texture.With the similar high fusion quality,the tensile strength and elongation of bulk samples were significantly improved from 257 MPa and 1.41%with the 10μm layer to 287 MPa and 15.12%with the 40μm layer,in accordance with the microstructural change.The effect of layer thickness on the compressive properties of porous scaffolds was limited.However,the corrosion rate of bulk samples accelerated with increasing the layer thickness,mainly attributed to the increased number of precipitation phases.
基金the National Natural Science Foundation of China(Grant number 51771178)Shaanxi Outstanding Youth Fund project(Grant number 2021JC-45)+2 种基金Key international cooperation projects in Shaanxi Province(Grant number 2020KWZ-007)the Major Program of Science and Technology in Shaanxi Province(Grant number20191102006)Open Fund of State Key Laboratory of Advanced Design and Manufacturing for Vehicle Body(Grant number 32115019)。
文摘The poor corrosion and wear resistances of Mg alloys seriously limit their potential applications in various industries.The conventional epoxy coating easily forms many intrinsic defects during the solidification process,which cannot provide sufficient protection.In the current study,we design a double-layer epoxy composite coating on Mg alloy with enhanced anti-corrosion/wear properties,via the spin-assisted assembly technique.The outer layer is functionalized graphene(FG)in waterborne epoxy resin(WEP)and the inner layer is Ce-based conversion(Ce)film.The FG sheets can be homogeneously dispersed within the epoxy matrix to fill the intrinsic defects and improve the barrier capability.The Ce film connects the outer layer with the substrate,showing the transition effect.The corrosion rate of Ce/WEP/FG composite coating is 2131 times lower than that of bare Mg alloy,and the wear rate is decreased by~90%.The improved corrosion resistance is attributed to the labyrinth effect(hindering the penetration of corrosive medium)and the obstruction of galvanic coupling behavior.The synergistic effect derived from the FG sheet and blocking layer exhibits great potential in realizing the improvement of multi-functional integration,which will open up a new avenue for the development of novel composite protection coatings of Mg alloys.
基金supported by the Grant of Russian Science Foundation,Russia (project no.21-73-10148,https://rscf.ru/en/project/ 21-73-10148/)supported by the Grant of Russian Science Foundation,Russia (project no.20-13-00130,https://rscf.ru/en/ project/20-13-00130/)。
文摘The high corrosion rate of magnesium and its alloys in chloride-containing solution significantly reduces the potential of this material for diverse applications.Therefore,the formation of a smart protective coating was achieved in this work to prevent degradation of the MA8 magnesium alloy.A porous ceramic-like matrix was obtained on the material by plasma electrolytic oxidation(PEO).Further surface functionalization was performed using layered double hydroxides(LDH) served as nanocontainers for the corrosion inhibitor.Several methods of LDH intercalation with benzotriazole(BTA) were proposed.The composition and morphology of the formed coating were studied using SEM-EDX analysis,XRD,XPS,and Raman microspectroscopy.The corrosion behavior of the coated samples was evaluated using electrochemical impedance spectroscopy and potentiodynamic polarization.The corrosion rate was estimated using volumetry and gravimetry methods.The formed composite coating provides the Mg alloy with the lowest corrosion activity(|Z|_(f)=0.1 Hz)=8.48·10^(5) Ω·cm^(2),I_(c)=1.4·10^(-8)A/cm^(2),P_(H)=0.21 mm/year) and improves the protective properties of the PEO-coated sample(|Z|_(f)=0.1 Hz)=8.37·10^(3) Ω·cm^(2),I_(c)=4.1·10^(-7)A/cm^(2),P_(H)=0.31 mm/year).The realization of the self-healing effect of the inhibitor-containing LDH/PEO-coated system was studied using localized electrochemical methods(SVET and SIET) with two artificial defects on the surface.A mechanism involving three stages for the active corrosion protection of the alloy was proposed.These findings contribute to the follow-up work of developing modified LDH/PEO-based structures that promote the Mg alloy with high corrosion resistance,superior electrochemical performance for applications in various fields of industry and medicine.
基金the support from National Natural Science Foundation of China (22179006)International Science & Technology Cooperation Program of China under Contract No.2019YFE0100200+3 种基金National Natural Science Foundation of China (52072036)NSAF (No.U1930113)Guangdong Key Laboratory of Battery Safety,China (No.2019B121203008)China Postdoctoral Science Foundation (No.2021TQ0034)。
文摘Lithium metal batteries represent promising candidates for high-energy-density batteries, however, many challenges must still be overcome,e.g., interface instability and dendrite growth. In this work, nano silica aerogel was employed to generate a hybrid film with high lithium ion conductivity(0.6 mS cm^(-1)at room temperature) via an in situ crosslinking reaction. TOF-SIMS profile analysis has revealed conversion mechanism of hybrid film to Li–Si alloy/Li F biphasic interface layer, suggesting that the Li–Si alloy and Li F-rich interface layer promoted rapid Li+transport and shielded the Li anodes from corrosive reactions with electrolyte-derived products. When coupled with nickel-cobalt-manganese-based cathodes, the batteries achieve outstanding capacity retention over 1000 cycles at 1 C. Additionally the developed film coated on Li enabled high coulombic efficiency(99.5%) after long-term cycling when coupled with S cathodes. Overall, the results presented herein confirm an effective strategy for the development of high-energy batteries.
基金This work was supported by the National Research Foundation of Korea(NRF)funded by the Korean government(MSIT)(No.2022R1A2C1006743).
文摘A novel inorganic-organic layer with outstanding corrosion resistance in a 3.5wt.% NaCl solution was fabricated by taking advantage of the unique interactions between coumarin (COM) molecules and the porous layer formed on Mg alloy. To achieve this aim, the AZ31 Mg alloy coated via microarc oxidation (MAO) coating was placed in an ethanolic solution of COM for 6 and 12 h at 25 ℃. By reducing the surface area exposed to the corrosive species, the donor-acceptor complexes produced by the particular interactions between the COM and MAO surface would successfully prevent the corrosion of Mg alloy substrate. The MAO layer would provide the ideal sites for the charge-transfer-induced physical and chemical locking, leading to uneven organic layer nucleation and crystal growth with a thatch-like structure. To evaluate the formation mechanism of such hybrid composites and highlight the key bonding modes between the COM and MAO, theoretical simulations were conducted.
基金This work was supported by the National Natural Science Foundation of China through the projects 51601108 and 52071191。
文摘Layered double hydroxide(LDH)coatings on magnesium(Mg)alloys shine brightly in the field of corrosion protection because of their special ion-exchange function.State-of-the-art steam coating as a type of LDH film preparation technique has emerged in recent years because only pure water is required as the steam source and its environmentally friendly LDH coating fits the current need for green development.Moreover,this coating can effectively inhibit the corrosion of the Mg alloy substrate due to the chemical bonding between the coating and the Mg alloy substrate.This review systematically explains cutting-edge advancements in the growth mechanism and corrosion behavior of LDH steam coatings,and analyzes the advantages and limitations of the steam-coating method.The influencing factors including pressure,CO_(2)/CO_(3)^(2-),aluminum content of the substrate alloy,solution type,and acid-pickling pretreatment,as well as the post-treatment of steam-coating defects,are comprehensively elucidated,providing new insights into the development of the in situ steam-coating technique.Finally,existing issues and future prospects are discussed to further accelerate the widespread application of Mg alloys.
基金the support from the National Natural Science Foundation of China(Grant No.22179006)supported by the Beijing Natural Science Foundation(2244101)+1 种基金the National Natural Science Foundation of China(Grant No.52072036)the SINOPEC project(223128)。
文摘Solid polymer electrolytes(SPEs)are urgently required to achieve practical solid-state lithium metal batteries(LMBs)and lithium-ion batteries(LIBs),Herein,we proposed a mechanism for modulating interfacial conduction and anode interfaces in high-concentration SPEs by LiDFBOP.Optimized electrolyte exhibits superior ionic conductivity and remarkable interface compatibility with salt-rich clusters:(1)polymer-plastic crystal electrolyte(P-PCE,TPU-SN matrix)dissociates ion pairs to facilitate Li+transport in the electrolyte and regulates Li^(+)diffusion in the SEI.The crosslinking structure of the matrix compensates for the loss of mechanical strength at high-salt concentrations;(2)dual-anion TFSI^(-)_(n)-DFBOP^(-)_(m)in the Li^(+)solvation sheath facilitates facile Li^(+)desolvation and formation of salt-rich clusters and is conducive to the formation of Li conductive segments of TPU-SN matrix;(3)theoretical calculations indicate that the decomposition products of LiDFBOP form SEI with lower binding energy with LiF in the SN system,thereby enhancing the interfacial electrochemical redox kinetics of SPE and creating a solid interface SEI layer rich in LiF.As a result,the optimized electrolyte exhibits an excellent ionic conductivity of9.31×10^(-4)S cm^(-1)at 30℃and a broadened electrochemical stability up to 4.73 V.The designed electrolyte effectively prevents the formation of Li dendrites in Li symmetric cells for over 6500 h at0.1 mA cm^(-2).The specific Li-Si alloy-solid state half-cell capacity shows 711.6 mAh g^(-1)after 60 cycles at 0.3 A g^(-1).Excellent rate performance and cycling stability are achieved for these solid-state batteries with Li-Si alloy anodes and NCM 811 cathodes.NCM 811‖Prelithiated silicon-based anode solid-state cell delivers a discharge capacity of 195.55 mAh g^(-1)and a capacity retention of 97.8%after 120 cycles.NCM 811‖Li solid-state cell also delivers capacity retention of 84.2%after 450 cycles.
基金supported by the National Research Foundation of Korea(NRF)funded by the Korean government(MSIT)(no.2022R1A2C1006743)。
文摘The self-assembly of hybrid inorganic-organic materials on stationary platforms plays a critical role in improving their structural stability and wide usability.In this work,a novel two-step hydrothermal approach is proposed for synthesizing stable and advanced hybrid coatings on metal-oxide platforms through the surface modification of layered double hydroxide(LDH)films using novel metal-organic frameworks(MOFs).Initially,Mg-Al LDH nanocontainers,grown on a magnesium oxide layer produced through plasma electrolytic oxidation(PEO)of AZ31 Mg alloy substrate,were intercalated with cobalt via an oxidation route,providing the metallic coordination center for the MOF formation.In the subsequent step,a pioneering technique is introduced,utilizing tryptophan as the organic linker for the first time at a pH of 10.The self-assembly of cobalt-tryptophan complex,driven by the strong bonding between electrophilic sites of monomers and nucleophilic sites,facilitated the formation of a MOF network having a cloud-like structure on the surface of MgAl LDH's film.The resulting MOF-LDH encapsulation containers demonstrate exceptional electrochemical stability when exposed to a 3.5 wt.%NaCl solution,surpassing the performance of PEO and pure LDH coatings.This enhanced stability is attributed to the development of a dense top layer and a stable composition within the self-assembled MOF,effectively sealing flaws and preventing the infiltration of corrosive ions into the underlying metallic substrate.The formation mechanism of MOFs on LDH galleries is investigated using density functional theory calculations.
文摘Effects of alloy elements on the microstructure and crack resistance of Fe-C-Cr weld surfacing layer were investigated. The results show that microstructures of the layer mainly consist of carbides and austenite matrix. Increasing C and Cr contents impair the crack resistance of the layer due to increased amount of brittle carbides. The addition of Ni, Nb or Mo improves the crack resistance of Fe-C-Cr weld surfacing layer by increasing the amount of austenite and forming fine NbC or M 7C 3 carbides in the layer. But, the excessive Nb (>2.50wt%) or Mo (>1.88wt%) impairs the crack resistance of the layer, which has relation with increased carbides or carbide coarsening and austenite matrix solid solution strengthening. The proper combination of C, Cr, Ni, Nb and Mo can further improve not only the crack resistance of Fe-C-Cr weld surfacing layer but also the erosion resistance as a result of fine NbC and M 7C 3 carbides distributing uniformly in austenite matrix. The optimal layer compositions are 3.05wt%C, 20.58wt%Cr, 1.75wt%Ni, 2.00wt%Nb and 1.88wt%Mo.
文摘Effects of alloying elements on microstructure and erosion resistance of Fe-C-Cr weld surfacing layer have been studied. The experimental results show that increasing C and Cr content favors improving the erosion resistance of the layer, and the excessive C and Cr result in decreasing the erosion resistance at 90 deg. erosion. That Mo, Nb or Ti improves the erosion resistance of Fe-C-Cr weld surfacing layer is mainly attributed to increasing the amount of M7C3 and forming fine NbC or TiC in austenite matrix, but the excessive Mo, Nb or Ti is unfavorable. The addition of Mo, Nb and Ti in proper combination possesses stronger effect on improving the erosion resistance and the erosion resistance (εA) of Fe-C-Cr weld surfacing layer with fine NbC, TiC and M7C3 distributing uniformly in austenite matrix obviously increases to 2.81 at 15 deg. erosion and 2.88 at 90 deg. erosion when the layer composition is 3.05C, 20.58Cr, 1.88Mo, 2.00Nb and 1.05Ti (in wt pct).
基金This work was supported by the National Natural Science Foundation of China (59971032) by Foundation for University Key Teacher, the Ministry of Education (GG-805-10056-1603).
文摘A simple chemical method was developed for inducing bioactivity on NiTi alloys (50 at. pct by Ni/Ti). A layer of calcium phosphate was deposited on the surface to improve biocompatibility of the alloy. NiTi alloys were first etched in HNO3 aqueous solution, and then treated with boiling diluted NaOH solution. A rough surface was created and a thin TiO2 layer was formed on the surface. Pre-calcification was then introduced by immersing the treated NiTi alloys in supersaturated Na2HPO4 solution and supersaturated Ca(OH)2 solution in turn before calcification in simulated body fluid (SBF). A dense and uniform bonelike calcium phosphate (Ca-P) bioactive layer was formed on the surfaces of the specimen, which would improve their biocompatibility. Morphology and element analysis on NiTi surfaces during the treatments were investigated in detail by means of environment scanning electron microscopy (ESEM), energy dispersion X-ray spectroscopy (EDXS), and X-ray diffraction (XRD).
文摘The Multi layer coating of Ni60 alloy was got by multi layer laser cladding. The height of the coating was about 12mm and the wall of the coating was perpendicular to the base. The microstructure of the coating was made up of fine dendrite. The conjunction between layers was good.
基金This project is financially supported by the National Natural Science Foundation of China (No. 50071028) the Natural Science Foundation of Shandong Province (No. L2000F01)
文摘The MAO (Micro-Arc Oxidation) process is applied to a eutectic Al-Si alloy(Al-12.0 percent Si-l.0 percent Cu-0.9 percent Mg (mass fraction)). The oxide ceramic layer wasfabricated with about 220 mum thickness and 3000 Hv micro-hardness. By XRD (X-ray diffractometry)and DSC (differential scanning calorimetry) analyses, the oxide layer consists of amorphous Al_2O_3,which is distinct from the results reported by the other researchers. The SEM photographs of suchlayer show that the layer is fixed tightly on the substrate alloy. So this alloy can he used in thehigh temperature and friction environment alter it is treated with such process.
基金The authors acknowledge the Project(81472058)sup-ported by the National Natural Science Foundation of Chinathe financial support of the 2015 ShanDong province project of outstanding subject talent group.the project(LSD-KB1806)+2 种基金supported by the foundation of National Key labo-ratory of Shock Wave and Detonation Physics and the project(11802284)supported by the National Natural Science Foun-dation of China.The project(2017GK2120)supported by the Key Research and Development Program of Hunan Province and the Natural Science Foundation of Hunan Province of China(2018JJ2506).
文摘For high corrosion resistance and extensively modified biodegradable Mg-based alloys and composites for bone implants,a new Mgbased matrix model prepared by powder metallurgy is discussed and developed.In this research,Mg-5 wt.%Zn alloys were selected as a case.And they were impacted by hot extrusion and aging treatments to construct microstructure with different characteristics.Their selfforming corrosion product layer in Ringer’s solution,biodegradable behavior and corrosion mechanism were minutely investigated by in vitro degradation,electrochemical corrosion and cytocompatibility.The results demonstrated the extruded Mg-5 wt.%Zn alloy aged for 96 h showed high corrosion resistance,good biocompatibility for L929 and excellent ability of maintaining sample integrity during the immersion.Significantly,the alloy showed fine-grain microstructure and uniform distributed hundred nano-sized second phases,which promoted the formation of the uniform and smooth corrosion product layer at the beginning of immersion.The corrosion product layer was more stable in chloride containing aqueous solution and could be directly formed and repaired quickly,which effectively protected the matrix from further corrosion.In addition,an ideal model of Mg-based matrix for bone tissue engineering was tried to presume and propose by discussing the causal relationship between microstructure and bio-corrosion process.
文摘After tempering treatment at different conditions, the tempering stability of Fe-base hardfacing layer containing RE and multiple alloying was investigated. The results show that after heat preservation at 560 ℃ and tempering for 4 h the hardness value of Fe-base hardfacing layer containing RE and multiple alloying can reach HRC57; By repeatedly heating circle 700 ℃17 ℃ for 150 times, the hardness value of Fe-base hardfacing layer can reach HRC43, tempering stability is higher and causes the secondary hardening phenomenon. Reasons for higher tempering stability of Fe-base hardfacing layer were analyzed by means of metallographic, XRD, TEM and EDS.
基金financial support by the Sichuan Science and Technology Program(No.2020YFG0165)the Projects in Sichuan Province Education Office(No.18ZA0453)+1 种基金the National Natural Science Foundation of China(No.51501156)the Sichuan Science and Technology Program(No.2019JDTD0024&No.2019ZHCG0048)。
文摘In this study,an environment-friendly layered double hydroxide(LDH)film has been deposited on Mg Ca alloy by a two-step technique.To improve the chemical conversion technique and control the film properties,batch studies have been carried out to address various process parameters such as pH value,treatment temperature and immersion time.The chemical composition was determined by X-ray diffractometry and energy dispersive X-ray spectroscopy.The morphology was characterized by scanning electron microscopy.The corrosion resistance of the samples with various films was compared by polarization curves and immersion test.It is found that the transformation duration of Mg-Fe LDH is long.Too high pH value and temperature has harmful effect on the purity of the film composition.The corrosion resistance of the films formed at low value of pH or high temperature or short treatment time is deteriorative.The optimum process is as follows:the sample is first immersed in the solution containing Fe^(3+)/HCO_(3)^-/CO_(3)^(2-)with a pH value of 5 at a temperature of 55℃for 1 h to form a precursor film,and then this precursor film is immersed into the solution containing Fe^(3+)/HCO_(3)^-/CO_(3)^(2-)with a pH of 11 at 55℃for 24 h to obtain the Mg-Fe LDH conversion film.
基金Supported by National Natural Science Foundation of China (50874033).
文摘Dissimilar metals TIG welding-brazing of aluminum alloy and non-coated stainless steel was investigated. The resultant joint was characterized in order to identify the phases and the brittle intermetallic compounds (IMCs) in the interracial layer by optical metalloscope (OM), scanning electron microscopy (SEM) and energy dispersive spectrometer ( EDS) , and the cracked joint was analyzed in order to understand the cracking mechanism of the joint. The results show that the microfusion of the stainless steel can improve the wetting and spreading of liquid aluminum base filler metal on the steel suuface and the melted steel accelerates the formation of mass of brittle IMCs in the interracial layer, which causes the joint cracking badly. The whole interfacial layer is 5 -7 μm thick and comprises approximately 5μm-thickness reaction layer in aluminum side and about 2 μm-thickness diffusion layer in steel side. The stable Al-rich IMCs are formed in the interfacial layer and the phases transfer from ( Al + FeAl3 ) in aluminum side to ( FeAl3 + Fe2Al5 ) and ( α-Fe + FeAl) in steel side.
文摘8-hydroxyquinoline(8-HQ)intercalated layered double hydroxides(LDH)film as underlayer and sol-gel layer was combined for active corrosion protection of the AM60B magnesium alloy.The LDH,LDH/sol-gel,and LDH@HQ/sol-gel coatings were analyzed using the scanning electron microscopy(SEM),field emission scanning electron microscopy(FESEM),energy dispersive X-ray spectroscopy(EDS),X-ray diffraction(XRD),atomic force microscopy(AFM),and electrochemical impedance spectroscopy(EIS)methods.The SEM images showed that the surface was entirely coated by the LDH film composed of vertically-grown nanosheets.The same morphology was observed for the LDH/sol-gel and LDH@HQ/sol-gel coatings.Also,almost the same topography was observed for both composite coatings except that the LDH@HQ/sol-gel coating had relatively higher surface roughness.Although the LDH film had the same impedance behavior as the alloy sample in 3.5wt%NaCl solution,its corrosion resistance was much higher,which could be due to its barrier properties as well as to the trap-ping of the chloride ions.Similar to the LDH film,the corrosion resistance of the LDH/sol-gel composite diminished with increasing the ex-posure time.However,its values were much higher than that of the LDH film,which was mainly related to the sealing of the solution path-ways.The LDH@HQ/sol-gel composite showed much better anti-corrosion properties than the LDH/sol-gel coating due to the adsorption of the 8-HQ on the damaged areas through the complexation.
文摘Composite,diffusive titanium nitride layers formed on a titanium and aluminum sub-layer were produced on the AZ91D magnesium alloy.The layers were obtained using a hybrid method which combined the PVD processes with the final sealing by a hydrothermal treatment.The microstructure,resistance to corrosion,mechanical damage,and frictional wear of the layers were examined.The properties of the AZ91D alloy covered with these layers were compared with those of the untreated alloy and of some engineering materials such as 316L stainless steel,100Cr6 bearing steel,and the AZ91D alloy subjected to commercial anodizing.It has been found that the composite diffusive nitride layer produced on the AZ91D alloy and then sealed by the hydrothermal treatment ensures the corrosion resistance comparable with that of 316L stainless steel.The layers are characterized by higher electrochemical durability which is due to the surface being overbuilt with the titanium oxides formed,as shown by the XPS examinations,from titanium nitride during the hydrothermal treatment.The composite titanium nitride layers exhibit high resistance to mechanical damage and wear,including frictional wear which is comparable with that of 100Cr6 bearing steel.The performance properties of the AZ91D magnesium alloy covered with the composite titanium nitride coating are substantially superior to those of the alloy subjected to commercial anodizing which is the dominant technique employed in industrial practice.