Two techniques that improve the aerodynamic performance of wind turbine airfoils are described. The airfoil $809, designed specially for wind turbine blades, and the airfoil FX60-100, having a higher lift-drag ratio, ...Two techniques that improve the aerodynamic performance of wind turbine airfoils are described. The airfoil $809, designed specially for wind turbine blades, and the airfoil FX60-100, having a higher lift-drag ratio, are selected to verify the flow control techniques. The flow deflector, fixed at the leading edge, is employed to control the boundary layer separation on the airfoil at a high angle of attack. The multi-island genetic algorithm is used to optimize the parameters of the flow deflector. The results indicate that the flow deflector can suppress the flow separation, delay the stall, and enhance the lift. The characteristics of the blade tip vortex, the wake vortex, and the surface pressure distributions of the blades are analyzed. The vortex diffuser, set up at the blade tip, is employed to control the blade tip vortex. The results show that the vortex diffuser can increase the total pressure coefficient of the core of the vortex, decrease the strength of the blade tip vortex, lower the noise, and improve the efficiency of the blade.展开更多
Experiment and numerical simulation technique are used to investigate the tip leakage flow in an axial fan with tip clearance at the design condition. The flow field in the tip region of fan is measured using a PDA (P...Experiment and numerical simulation technique are used to investigate the tip leakage flow in an axial fan with tip clearance at the design condition. The flow field in the tip region of fan is measured using a PDA (Particle Dynamics Analysis) system. The flow is surveyed across the whole passage at fifteen axial locations (from the 100% axial chord in front of the leading edge to the 100% axial chord behind the trailing edge), mainly focusing on the outer 90% blade span. Both experiment measurement and numerical simulation indicates the leakage flow originated from the tip clearance along the chord rolls up into three dimensional spiral structure to form leakage flow vortex. The interaction of leakage flow and main flow will produce the low velocity zone, and block the flow. The leakage flow almost occupies the most part of flow passage behind the trailing edge.展开更多
In the present paper the attention is focused on correlation between fan noise and velocity fluctuations of tip leakage vortex around rotor blade of a low pressure axial flow fan at the maximum pressure operating poin...In the present paper the attention is focused on correlation between fan noise and velocity fluctuations of tip leakage vortex around rotor blade of a low pressure axial flow fan at the maximum pressure operating point. We measured time fluctuating velocity near the rotor tip around the rotor blades by using a hot-wire sensor from a relative flame of refer- ence fixed to the rotor blades. As the results, it is clear that the velocity fluctuation due to tip leakage vortex has weak periodicity and the hump portion appeared in its spectrum. If the flow rate was lower than the design condition, the tip leakage flow became to attach to the following blade and the sound pressure level at frequency of velocity fluctuation of this flow was increased. The correlation measurements between the velocity fluctuation of tip leakage flow and the aerodynamic noise were made using a rotating hot-wire sensor near the rotor tip in the rotating frame. The correlation between the velocity fluctuation due to tip leakage flow and acoustic pressure were increased due to generation of weak acoustic resonance at the maximum pressure operating point.展开更多
By means of ink trace visualization of the flows in conventional straight, positively curved and negatively curved cascades with tip clearance, and measurement of the aerodynamic parameters in transverse section, and...By means of ink trace visualization of the flows in conventional straight, positively curved and negatively curved cascades with tip clearance, and measurement of the aerodynamic parameters in transverse section, and by appling topology theory, the topological structures and vortex structure in the transverse section of a blade cascade were analyzed. Compared with conventional straight cascade, blade positive curving eliminates the separation line of the upper passage vortex, and leads the secondary vortex to change from close separation to open separation, while blade negative curving effects merely the positions of singular points and the intensities and scales of vortex.展开更多
Large-view flow field measurements using the particle image velocimetry （PIV） technique with high resolution CCD cameras on a rotating 1/8 scale blade model of the NREL UAE phase VI wind turbine are conducted in the...Large-view flow field measurements using the particle image velocimetry （PIV） technique with high resolution CCD cameras on a rotating 1/8 scale blade model of the NREL UAE phase VI wind turbine are conducted in the engineering-oriented q53.2 m wind tunnel. The motivation is to establish the database of the initiation and development of the tip vortex to study the flow structure and mechanism of the wind turbine. The results show that the tip vortex first moves inward for a very short period and then moves outward with the wake expansion, while its vorticity decreases with time after being trailed from the trailing edge of the blade tip, and then increases continuously with the rapid rolling-up to form a strong tip vortex. The measurements also indicate that the downstream movement of the tip vortex is nearly linear in the very near wake under the test condition.展开更多
基金Project supported by the National Basic Research Program of China (973 Program) (No. 2007CB714600)
文摘Two techniques that improve the aerodynamic performance of wind turbine airfoils are described. The airfoil $809, designed specially for wind turbine blades, and the airfoil FX60-100, having a higher lift-drag ratio, are selected to verify the flow control techniques. The flow deflector, fixed at the leading edge, is employed to control the boundary layer separation on the airfoil at a high angle of attack. The multi-island genetic algorithm is used to optimize the parameters of the flow deflector. The results indicate that the flow deflector can suppress the flow separation, delay the stall, and enhance the lift. The characteristics of the blade tip vortex, the wake vortex, and the surface pressure distributions of the blades are analyzed. The vortex diffuser, set up at the blade tip, is employed to control the blade tip vortex. The results show that the vortex diffuser can increase the total pressure coefficient of the core of the vortex, decrease the strength of the blade tip vortex, lower the noise, and improve the efficiency of the blade.
文摘Experiment and numerical simulation technique are used to investigate the tip leakage flow in an axial fan with tip clearance at the design condition. The flow field in the tip region of fan is measured using a PDA (Particle Dynamics Analysis) system. The flow is surveyed across the whole passage at fifteen axial locations (from the 100% axial chord in front of the leading edge to the 100% axial chord behind the trailing edge), mainly focusing on the outer 90% blade span. Both experiment measurement and numerical simulation indicates the leakage flow originated from the tip clearance along the chord rolls up into three dimensional spiral structure to form leakage flow vortex. The interaction of leakage flow and main flow will produce the low velocity zone, and block the flow. The leakage flow almost occupies the most part of flow passage behind the trailing edge.
文摘In the present paper the attention is focused on correlation between fan noise and velocity fluctuations of tip leakage vortex around rotor blade of a low pressure axial flow fan at the maximum pressure operating point. We measured time fluctuating velocity near the rotor tip around the rotor blades by using a hot-wire sensor from a relative flame of refer- ence fixed to the rotor blades. As the results, it is clear that the velocity fluctuation due to tip leakage vortex has weak periodicity and the hump portion appeared in its spectrum. If the flow rate was lower than the design condition, the tip leakage flow became to attach to the following blade and the sound pressure level at frequency of velocity fluctuation of this flow was increased. The correlation measurements between the velocity fluctuation of tip leakage flow and the aerodynamic noise were made using a rotating hot-wire sensor near the rotor tip in the rotating frame. The correlation between the velocity fluctuation due to tip leakage flow and acoustic pressure were increased due to generation of weak acoustic resonance at the maximum pressure operating point.
文摘By means of ink trace visualization of the flows in conventional straight, positively curved and negatively curved cascades with tip clearance, and measurement of the aerodynamic parameters in transverse section, and by appling topology theory, the topological structures and vortex structure in the transverse section of a blade cascade were analyzed. Compared with conventional straight cascade, blade positive curving eliminates the separation line of the upper passage vortex, and leads the secondary vortex to change from close separation to open separation, while blade negative curving effects merely the positions of singular points and the intensities and scales of vortex.
基金Project supported by the National Basic Research Program of China (973 Program) (No. 2007CB714600)
文摘Large-view flow field measurements using the particle image velocimetry （PIV） technique with high resolution CCD cameras on a rotating 1/8 scale blade model of the NREL UAE phase VI wind turbine are conducted in the engineering-oriented q53.2 m wind tunnel. The motivation is to establish the database of the initiation and development of the tip vortex to study the flow structure and mechanism of the wind turbine. The results show that the tip vortex first moves inward for a very short period and then moves outward with the wake expansion, while its vorticity decreases with time after being trailed from the trailing edge of the blade tip, and then increases continuously with the rapid rolling-up to form a strong tip vortex. The measurements also indicate that the downstream movement of the tip vortex is nearly linear in the very near wake under the test condition.
