TC11 titanium alloy samples with lamellar microstructrue were compressed on a Gleeble 1500D Simulator.Compression tests were carried out at 950 ℃ and a strain rate of 0.1 s-1 with height reduction of 20%,40% and 60%,...TC11 titanium alloy samples with lamellar microstructrue were compressed on a Gleeble 1500D Simulator.Compression tests were carried out at 950 ℃ and a strain rate of 0.1 s-1 with height reduction of 20%,40% and 60%,respectively.Microstruture of the compressed TC11 alloy was obeserved and analyzed by optical microscopy(OM),transmission electron microscope(TEM),electron back-scattered diffraction(EBSD).The lamellar disintegration mechanism of the TC11 titanium alloy was deduced.The results indicated that the compressive deformation promoted the phase transformation in bi-phase area.βphase layers were formed along the gliding planes inα phase,and α slivers were disintegrated into many small flakes through theα/βinterface slipping.展开更多
Abstract Transient stress and strain fields of dissimilar titanium alloys （TCll and TC17 ） joint during linear friction welding （ LFW） were investigated by a two-dimensional model with ABAQUS/Explicit. The results...Abstract Transient stress and strain fields of dissimilar titanium alloys （TCll and TC17 ） joint during linear friction welding （ LFW） were investigated by a two-dimensional model with ABAQUS/Explicit. The results showed that in the X-axis, the maximum compressive stress of 850 MPa occurred in the center zone of friction interface , and the maximum tensile stress of 190 MPa distributed at the flash; in the Y-axis, the maximum compressive stress of 1 261 MPa located at the junction region between the welding fixture and edge of the specimen, and the maximum tensile stress of 320 MPa distributed in the connecting portion between the flash and edge of the specimen. In addition, areas of plastic strain increased gradually during welding process. In the X-axis, tensile strain mainly existed at the heads of the specimens; in the Y-axis, compressive strain mainly occurred at the heads of the specimens.展开更多
Laser powder deposition was applied to fabricate the Ti-6.5Al-3.5Mo-1.5Zr-0.3Si （wt%）/Ti-47Al- 2Cr-2Nb-0.2W-0.15B （at%） bi-material system. The asdeposited TC11 alloy shows a basket-wave-like morphology while the ...Laser powder deposition was applied to fabricate the Ti-6.5Al-3.5Mo-1.5Zr-0.3Si （wt%）/Ti-47Al- 2Cr-2Nb-0.2W-0.15B （at%） bi-material system. The asdeposited TC11 alloy shows a basket-wave-like morphology while the as-deposited y-TiAl alloy consists of fully α2/γ lamellar microstructures. Regarding the thermal mismatch between TC11 and γ-TiAl during processing, the interface microstmcture evolution was concerned. The transformation pathway was illustrated. It is found that the content changes of Al elements and β-stabilizers Mo, Cr, and Nb are responsible for the evolution of microstructures at the interface. The fracture surfaces are located at the y-TiAl side. The bi-material shows a brittle-fracture manner, with the ultimate tensile strength of 560 MPa.展开更多
On the bases of high temperature creep experiments, the research on engineering application of rheological forming is carried out on two kinds of light metal alloy parts named cylindrical shell of Lc4 aluminum alloy a...On the bases of high temperature creep experiments, the research on engineering application of rheological forming is carried out on two kinds of light metal alloy parts named cylindrical shell of Lc4 aluminum alloy and vane disk with complex curved surface of TC11 titanium alloy. Moreover, the mechanical property tests under room and high temperatures for the workpieces produced by this new technique are also done, the results showed that they are much improved evidently compared with those produced by traditional method.展开更多
基金Funded by the National Key Natural Science Foundation of China(No.5131903ZT1)
文摘TC11 titanium alloy samples with lamellar microstructrue were compressed on a Gleeble 1500D Simulator.Compression tests were carried out at 950 ℃ and a strain rate of 0.1 s-1 with height reduction of 20%,40% and 60%,respectively.Microstruture of the compressed TC11 alloy was obeserved and analyzed by optical microscopy(OM),transmission electron microscope(TEM),electron back-scattered diffraction(EBSD).The lamellar disintegration mechanism of the TC11 titanium alloy was deduced.The results indicated that the compressive deformation promoted the phase transformation in bi-phase area.βphase layers were formed along the gliding planes inα phase,and α slivers were disintegrated into many small flakes through theα/βinterface slipping.
文摘Abstract Transient stress and strain fields of dissimilar titanium alloys （TCll and TC17 ） joint during linear friction welding （ LFW） were investigated by a two-dimensional model with ABAQUS/Explicit. The results showed that in the X-axis, the maximum compressive stress of 850 MPa occurred in the center zone of friction interface , and the maximum tensile stress of 190 MPa distributed at the flash; in the Y-axis, the maximum compressive stress of 1 261 MPa located at the junction region between the welding fixture and edge of the specimen, and the maximum tensile stress of 320 MPa distributed in the connecting portion between the flash and edge of the specimen. In addition, areas of plastic strain increased gradually during welding process. In the X-axis, tensile strain mainly existed at the heads of the specimens; in the Y-axis, compressive strain mainly occurred at the heads of the specimens.
基金financially supported by the National Basic Research Development Program of China(No.2011CB606305)
文摘Laser powder deposition was applied to fabricate the Ti-6.5Al-3.5Mo-1.5Zr-0.3Si （wt%）/Ti-47Al- 2Cr-2Nb-0.2W-0.15B （at%） bi-material system. The asdeposited TC11 alloy shows a basket-wave-like morphology while the as-deposited y-TiAl alloy consists of fully α2/γ lamellar microstructures. Regarding the thermal mismatch between TC11 and γ-TiAl during processing, the interface microstmcture evolution was concerned. The transformation pathway was illustrated. It is found that the content changes of Al elements and β-stabilizers Mo, Cr, and Nb are responsible for the evolution of microstructures at the interface. The fracture surfaces are located at the y-TiAl side. The bi-material shows a brittle-fracture manner, with the ultimate tensile strength of 560 MPa.
基金supported by the National Personnel Department for returned talents(lincaipeizi[2001]30#)the Education Ministry of China for the university with doctoral discipline (No. 200805380004)
文摘On the bases of high temperature creep experiments, the research on engineering application of rheological forming is carried out on two kinds of light metal alloy parts named cylindrical shell of Lc4 aluminum alloy and vane disk with complex curved surface of TC11 titanium alloy. Moreover, the mechanical property tests under room and high temperatures for the workpieces produced by this new technique are also done, the results showed that they are much improved evidently compared with those produced by traditional method.
