INFLUENCE OF HOT DEFORMATION ON CONTINUOUSCOOLING BAINITIC TRANSFORMATION IN A LOWCARBON STEEL

The influence of hot deformation conditions on continuous cooling bainitic transformation has been investigated for a low carbon microalloyed steel. The CCT diagrams show that deformation in unrecrpstallized austcnite ation can accelerate transformation process. Bainitic transformation in intermediate transformation temperature region is prominent, and the proeutectoid polygonal ferrite transformation at evelated high temperature is suppressed. According to optical and TEM analyses, low carbon bainitic ferrite is characterized by granular and lathlike ferrite, based on the cooling rate and deformation conditions. For nondeformation, groaps of coarse parallel ferrite lath form from the prior austenite grain boundaries with the same crystallographic orientation. For heavy deformaton, cell structure within the austenite grains due to the high dislocation density formed, which provides more nucleation sites for bainite ferrite. So deformation can discontinue the growth of ferrite laths and decrease the length of ferrite laths.

Effect of tempering temperature on the mechanical properties and microstructure of an copper-bearing low carbon bainitic steel

The effect of tempering temperature on the microstructure and mechanical properties of ultra-high strength, copperbearing, low-carbon bainitic steel has been investigated in the experiment. The results showed that the microstructure was mainly the laths of bainite in the as-quenched steel. The bainitic laths were restored and combined after the steel tempered at various tempera- tures. There were rnartensite/austenite （M/A） islands and numerous dislocations within and between the bainitic laths, while very t-me precipitates of ε-Cu were also observed within the laths. With increasing the tempered temperature from 400 to 600℃, the yield strength （YS） increased from 877 to 957 MPa, whereas the ultimate tensile strength （UTS） decreased from 1020 to 985 MPa. The Charpy V-notch （CVN） varied from 68.5 to 42 J, and the value was minimal for the steel tempered at 500℃. 2008 University of Science and Technology Beijing. All rights reserved.

Effects of Mn on Microstructures and Properties of Hot Rolled Low Carbon Bainitic Steels

Two kinds of Mn-Si-Mo low carbon steels were designed to study the effects of Mn on the microstructures and properties of hot rolled low carbon bainitic steels.To reduce the production cost,a very low Mo content of 0.13%was added in both steels.After hot rolling,the mechanical properties of samples were tested.Microstructure was observed and analyzed by optical microscope and transmission electron microscope.The results show that the strength of tested steels increases with the increase in Mn content,while the elongation decreases.When Mn content increases,the bainite microstructure increases.The results can provide a theoretical basis for composition design and industrial production of low cost low carbon bainitic steels.

Structure Character of M-A Constituent in CGHAZ of New Ultra-Low Carbon Bainitic Steel under Laser Welding Conditions

800 MPa grade new ultra-low carbon bainitic （NULCB） steel is the recently developed new generation steel. The microstructure in the coarse-grained heat affected zone （CGHAZ） of NULCB steel under laser welding conditions was investigated by thermal simulation. The influence of the cooling time from 800℃ to 500℃.t8/5 （0.3-30 s）, on the microstructure of the CGHAZ was discussed. The experimental results indicate that the microstructnre of the CGHAZ is only the granular bainite which consists of bainitic ferrite （BF） lath and M-A constituent while t8/5 is 0.3-30 s. The M-A constituent consists of twinned martensite and residual austenite, and the change of the volume fraction of the residual austenite in the M-A constituent is very small when t8/5 is between 0.3 and 30 s. The morphology of the M-A constituent obviously changes with the variation of t8/5.As t8/5 increases, tile average width, gross and shape parameter of the M-A constituent increase, while the line density of the M-A constituent decreases.

PHASE TRANSFORMATION UNIT OF BAINITIC FERRITE AND ITS SURFACE RELIEF IN LOW AND MEDIUM CARBON ALLOY STEELS

The lath-or plate-shaped bainitic ferrite of low and medium carbon alloy steels consists of packets of ferrite sublaths which are composed of many finer and regular ferrite blocks.They are uniform shear growth units of bainitic phase transformation.No carbide is precipitated from them.The bainitic O-carbides are precipitated from γ-α interface or carbon-rich austenite.The mode of arrangement of the units in ferrite sublath packet is in uni-or bi-di- rection.Single surface relief is produced by the accumulation of uniform shear strains with all the ferrite units arranged unidirectionally in a sublath packet,while tent-shaped surface relief is formed by the integration of the uniform shear strains of two groups with ferrite units piling up in two directions and growing face to face;whereas if they grow back to back,the integra- tion will be responsible for invert-tent-shaped surface relief.The interface trace between two groups of ferrite units in a sublath packet is shown as“midrib”.

Mechanical Method Determining Precipitation in an Ultra-Low Carbon Bainitic Steel

Stress relaxation was chosen as the best method for monitoring the precipitation process. Tests were carried out on an ultra-low carbon bainitic steel containing Mn, Nb and B over 800~950℃. Specimens were solu- tion treated at 1250℃ for a certain holding period. A prestain of 20% was applied at a strain rate of 0.1/s. The exper- imental results are displayed by a set of stress vs. 1g(time) curves different from the typical stress relaxation curves. There are two singularities forming a stress plateau on the stress vs.1g(time) curves when precipitates could be observed. Suppose the first one is the start of precipitation (Ps), and the second represcnts the fihish (Pf). As a result Precipitation-Time-Temperature relationship is described as C-shape curves based on two points. This mechanical method is suitable and precise for measuring precipitates in microalloyed steels during hot working.

Bainite Transformation Under Continuous Cooling of Nb-Microalloyed Low Carbon Steel

Utilizing Gleeble-1500 thermomechanical simulator, the influences of hot deformation parameters on continuous cooling bainite transformation in Nb-microalloyed low carbon steel were investigated. The results indicate that bainite starting temperature decreases with raising cooling rate and increases with increasing deformation temperature. Deformation has an accelerative effect on the bainite transformation when the specimens are deformed at 950 ℃. When the deformation temperature increases, the effect of deformation on bainite starting temperature is weakened. The amount of bainite is influenced by strain, cooling rate, and deformation temperature. When the specimens are deformed below 900 ℃, equiaxed ferrites are promoted and the bainite transformation is suppressed.

Kinetics of bainite-to-austenite transformation during continuous reheating in low carbon microalloyed steel

A dilatometer was used to study the kinetics of bainite-to-austenite transformation in low carbon microalloyed steel with the initial microstructure of bainite during the continuous reheating process. The bainite-to-austenite trans- formation was observed to take place in two steps at low heating rate. The first step is the dissolution of bainite, and the second one is the remaining bainite-to-austenite transformation controlled by a dissolution process. The calculation result of the kinetics of austenite formation shows that the two steps occur by diffusion at low heating rate. However, at high heating rate the bainite-to-austenite transformation occurs in a single step, and the process is mainly dominated by shear. The growth rate of austenite reaches the maximum at about 835℃ at different heating rates and the growth rate of austenite as a function of temperature increases with the increase in heating rate.

Effects of Deformation on Bainite Transformation During Continuous Cooling of Low Carbon Steels

Hot deformation experiments were carried out on Gleeble 1500 thermo-mechanical simulator. The bainite transformation after deformation was investigated by optical microstructure analysis. The results indicated that the deformation accelerated the bainite transformation when the deformation was carried out at high temperature and no or little ferrite was precipitated before bainite transformation; when the deformation was carried out at low temperature, the deformation hindered the bainite transformation because a lot of ferrite precipitated before bainite transformation.

Effect of zirconium addition on the austenite grain coarsening behavior and mechanical properties of 900 MPa low carbon bainite steel

The ultra-fine bainitic microstructure of a 900 MPa low carbon bainitic Cu-Ni-Mo-B steel was obtained by a newly developed relaxation precipitation control （RPC） phase transformation processing. In a pan-cake like prior-austenite grain, the micro- structure consisted of lath bainite, a little of abnormal granular bainite, and acicular ferrite. The effect of zirconium carbonitrides on the austenite grain coarsening behavior was studied by transmission electron microscopy （TEM）. The results show that, the lath is narrower with increasing cooling rate. The ratio of all kinds of bainitic microstructure is proper with the intermediate cooling rate; and Zr-containing precipitates distribute uniformly, which restrains austenite grain growing in heat-affected welding zone.

EFFECT OF MICROSTRUCTURE ON CORROSION FATIGUE BEHAVIOUR OF A LOW CARBON BAINITE STEEL

The behaviour towards corrosion fatigue of low carbon bainite steel with various microstructures after tempered at different temperatures has been examined. The susceptibility of the steel to corrosion fatigue may be improved by tempering at 300℃.

Effect of silicon and prior deformation of austenite on isothermal transformation in low carbon steels

Isothermal transformation （TTT） behavior of the low carbon steels with two Si contents （0.50 wt pct and 1.35 wt pct） was investigated with and without the prior deformation. The results show that Si and the prior deformation of the austenite have significant effects on the transformation of the ferrite and bainite. The addition of Si refines the ferrite grains, accelerates the polygonal ferrite transformation and the formation of M/A constituents, leading to the improvement of the strength. The ferrite grains formed under the prior deformation of the austenite become more homogeneous and refined. However, the influence of deformation on the tensile strength of both steels is dependent on the isothermal temperatures. Thermodynamic calculation indicates that Si and prior deformation reduce the incubation time of both ferrite and bainite transformation, but the effect is weakened by the decrease of the isothermal temperatures.

Effect of Nb on the Microstructure and Properties of Cold Rolled and Annealed Mo Microalloyed Bainitic Steel

Two kinds of low carbon bainitic steels,Nb-free Mo bearing and Nb + Mo addition steels,were cold rolled and annealed to investigate the effect of micro-alloying element Nb on the microstructure and properties of Mo microalloyed low carbon high strength bainitic steel. No precipitates were observed in Nb-free Mo bearing steel,whereas,two types of precipitates,i.e.,Nb( C,N) and composite( Nb,Mo)( C,N),were observed in the Nb + Mo microalloyed steel,resulting in precipitation strengthening. The strength of Mo bearing steel was improved by addition of Nb under the same annealing conditions. The grain size of Nb addition steel was almost the same as Nb-free steel. Unlike the obvious grain refinement and precipitation strengthening in hot rolling,the increase in yield strength of Nb addition steels in cold rolling and annealing mainly results from the precipitation strengthening,while the effect of grain refinement strengthening can be almost ignored.

A creep technique for monitoring the aging precipitation in Cu-Nb bainitic steels

A creep technique was applied on a Gleeble-1500 thermal simulator for monitoring the aging precipitation in ultra-low carbon steels containing various coppers. The aging hardening curve was obtained by the hardness testing. With the aid of an optical microscope and TEM, the microstructure and the aging precipitates were detected. The results indicate that when the precipitation occurs during the creep a plateau will appear on the creep curve; the left-hand and right-hand endings of the plateau correspond to the precipitation start （Ps） and finish （Pf） times, respectively. The Pf obtained from the creep curve coincides with the peak hardness time （tp） at the aging hardening curve. A precipitation-time-temperature （PTT） diagram of the steel can be obtained.

Continuous Cooling Transformation Behavior and Kinetic Models of Transformations for an Ultra-Low Carbon Bainitic Steel

The aim was to investigate transformation behavior and transformation kinetics of an ultra-low carbon bai- nitic steel during continuous cooling. Continuous cooling transformation （CCT） curves of tested steel were measured by thermal dilatometer and metallographic structures at room temperature were observed by optical microscope. Then transformation kinetic equation of austenite to ferrite as well as austenite to bainite was established by analyzing the relationship of lnln]-l/（1--f）] and lnt in the kinetic equation on the basis of processed experimental data. Finally, the measured and calculated kinetic behaviors of the steel during continuous cooling were compared and growth pat- terns of transformed ferrite and bainite were analyzed. Results showed that calculated result was in reasonable agree- ment with the experimental data. It could be concluded that the growth modes of transformed ferrite and bainite were mainly one dimension as the Avrami exponents were between 1 and 2.

Effect of boron addition on the microstructures and mechanical properties of thermomechanically processed and tempered low carbon bainitic steels

Thermomechanical process and tempering heat treatment were employed to produce the experimental steel plates. The effect of boron addition on the microstructure and mechanical properties of low carbon bainitic steels was studied in this paper. Microstructure observation and crystallographic features were conducted by using optical microscopy, SEM, TEM and electron back scattering diffraction （EBSD） analysis. The results showed that under the same rolling processes and heat treatment conditions, a substantial increase in strength is obtained by addition of boron into steel, but accompanied by an obvious drop in toughness. New martensite phase forms along the grain boundaries on tempering at 650℃ mainly due to boron segregation, which can further deteriorate impact toughness of the boron bearing steel. The EBSD analysis showed that high angle grain boundary, is not responsible for the deteriorated toughness of the boron bearing steel because it has relatively higher percentage of high angle grain boundary than the boron free steel. The low toughness of the boron bearing steel is mainly attributed to the coarse boride precipitated particles according to the results of fractograph observation.

Study on Microstructure Refinement of Vanadium and Nitrogen Microalloyed Low Carbon Bainitic Steel

The effect of relaxation treatment after finish rolling on microstructure and mechanical properties has been investigated for a vanadium and nitrogen microalloyed low carbon bainitic steel.Finer lath bainite microstructure can be obtained in the plate with relaxation.The results of quantitative statistics show that in the plate without relaxation,80% of the total bainite lath bundles are in the range 5-15μm in length and 3-13μm in width,while in the plate with relaxation 80% of the total bundles are in the range 3-9μm in length and 1-7μm in width.The mechanical properties show that the plate with relaxation has higher impact energy,yield strength and hardness than the plate without relaxation,also the comprehensive performance after tempered at 650℃ is superior to the plate without relaxation.

Mn-Series Low-Carbon Air-Cooled Bainitic Steel Containing Niobium of 0.02%

A new hot rolled low-carbon air-cooled bainitic steel containing Nb of 0.02% has been developed based on alloying design of the grain boundary allotriomorphic ferrite （FGBA）/granular bainite （BG） duplex steel. The as-rolled microstructure and mechanical properties of bainitie steel containing Nb of 0. 02% were investigated by tensile test, optical microscopy （OM）, scanning electron microscopy （SEM）, and transmission electron microscopy （TEM）. The results show that adding 0.02 % of Nb obviously improves the strength without sacrificing toughness of the FGBA/BG steel. Adding 0.02% of Nb not only refines the grain boundary allotriomorphic ferrite grains but also promotes the refinement of granular bainite including its bainitic ferrite and M/A island. Any Nb（C,N） has been hardly observed in the steel containing Nb of 0.02%. It is suggested that the strengthening mechanism of Nb of 0.02% can be mainly attributed to the effect of Nb in solution （solute drag-like effect） on the phase transformation rather than the precipitation strengthening of Nb（C, N） particles.

Weldability of 1000 MPa Grade Ultra-low Carbon Bainitic Steel

Maximum hardness test in weld heat-affected zone（HAZ）,oblique Y-groove cracking test and mechanical property test of welding joint of 1 000 MPa grade ultra-low carbon bainitic steel were carried out,so as to research the weldability of the steel.The results show that the steel has lower cold cracking sensitivity,and preheating temperature of 100 ℃ can help completely eliminate cold cracks,generating good process weldability.The increase of preheating temperature can reduce the hardening degree of heat-affected zone.The strength of welding joint decreases and hardness reduces when heat inputs increase,and excellent mechanical properties can be obtained when low welding heat inputs are used.Fine lath bainites of different orientations combined with a few granular bainites that effectively split the original coarse austenite grains are the foundation of good properties.

Evolution of Microstructures of a Low Carbon Bainitic Steel Held at High Service Temperature

Low carbon bainitic steel derives the high strength mainly from high density of dislocations rather than carbon and alloy element content, so it tends to evolve into equilibrium microstructure with low density of dislocations under thermal disturbance. In the present investigation, granular bainite and lath-like bainitic ferrite were produced respectively in Mo-free low-carbon steels by changing cooling rate;. It has been found that granular bainite possesses a lower strength at room temperature than bainitic ferrite, but it exhibits a slower decrease of strength with temperature increasing. Dislocation density in both granular bainite and bainitic ferrite decreases via recovery and recrystallization at high temperature. However, when reheating of bainite is carded out at temperature below 600 ℃, a long time will be needed for incubation of recrystallization, during which the hardness of bainite maintains stable. The property makes bainite, especially granular bainite, become a potential microstructure for matrix of high strength fire-resistant steel.