The effects of operation parameters of combined blowing converter on the volumetric mass transfer coefficient between slag and steel are studied with a cold model with water simulating steel, oil simulating slag and b...The effects of operation parameters of combined blowing converter on the volumetric mass transfer coefficient between slag and steel are studied with a cold model with water simulating steel, oil simulating slag and benzoic acid as the transferred substance between water and oil. The results show that, with lance level of 2.1m and the top blowing rate of 25000Nm3/h, the volumetric mass transfer coefficient changes most significantly when the bottom blowing rate ranges from 384 to 540Nm3/h. The volumetric mass transfer coefficient reaches its maximum when the lance level is 2.1m, the top blowing rates is 30000Nm3/h, and the bottom blowing rate is 384Nm3/h with tuyeres located symmetrically at 0.66D of the converter bottom.展开更多
China is an important country in iron and steel industry.Power electronics converters are widely used.For the cold rolling mills of high speed,AC-DC-AC converters should be used.In the paper,the design and the control...China is an important country in iron and steel industry.Power electronics converters are widely used.For the cold rolling mills of high speed,AC-DC-AC converters should be used.In the paper,the design and the control system of the large power three-level AC - DC - AC converter with IGCTs is investigated,and a back-to-back large power three-level AC - DC - AC converter with IGCTs has been got. With a series experiments,the performance of the converter is examined.The experiment result indicates the converter reaches the design requirement and it shows excellent performance.The converter system has been put into use safely.It is estimated that the AC - DC - AC converter system will be used in the drive systems for rolling mills in the near future.展开更多
The bottom blowing element is the key equipment to ensure the bottom blowing effect of the converter.Three types of bottom blowing elements,dispersive type(D1),double circular seam(D2)and straight cylinder type(D3),we...The bottom blowing element is the key equipment to ensure the bottom blowing effect of the converter.Three types of bottom blowing elements,dispersive type(D1),double circular seam(D2)and straight cylinder type(D3),were built,and the effects of bottom blowing element type on molten bath flow,wall erosion and furnace bottom erosion were simulated.It was found that when the bottom blowing elements of dispersive type(D1)and double circular seam(D2)were used,the dead zone area in the lower part of the molten bath was smaller,and the high-speed zone area was larger;therefore,the stirring effect on the bottom melt was better.When the straight cylinder type(D3)bottom blowing element was used,the gas penetrated the molten bath at a faster rate to reach the surface of molten bath and failed to disperse in the bottom molten bath,and the wall shear stress near the nozzle outlet was larger.When argon was blown by three different bottom blowing elements,the area of the wall shear stress greater than 3 Pa was 4.8,5.6 and 8.7 cm2,respectively,within 0.2 m of the bottom blowing nozzle outlet.展开更多
By measuring the volume concentration of SO<sub>2</sub> produced,blow rate of air（m<sup>3</sup>/min）Band converting times τ,the mathematical model of converting for oxidizing FeS and Cu<s...By measuring the volume concentration of SO<sub>2</sub> produced,blow rate of air（m<sup>3</sup>/min）Band converting times τ,the mathematical model of converting for oxidizing FeS and Cu<sub>2</sub>S,and that of controlling end point can be developed according to the slag making period andcopper making period,respectively.This derived model may be well suitable for either sideblow or top blow converter if the parameters-SO<sub>2</sub>B,τ.can be measured accurately.展开更多
文摘The effects of operation parameters of combined blowing converter on the volumetric mass transfer coefficient between slag and steel are studied with a cold model with water simulating steel, oil simulating slag and benzoic acid as the transferred substance between water and oil. The results show that, with lance level of 2.1m and the top blowing rate of 25000Nm3/h, the volumetric mass transfer coefficient changes most significantly when the bottom blowing rate ranges from 384 to 540Nm3/h. The volumetric mass transfer coefficient reaches its maximum when the lance level is 2.1m, the top blowing rates is 30000Nm3/h, and the bottom blowing rate is 384Nm3/h with tuyeres located symmetrically at 0.66D of the converter bottom.
文摘China is an important country in iron and steel industry.Power electronics converters are widely used.For the cold rolling mills of high speed,AC-DC-AC converters should be used.In the paper,the design and the control system of the large power three-level AC - DC - AC converter with IGCTs is investigated,and a back-to-back large power three-level AC - DC - AC converter with IGCTs has been got. With a series experiments,the performance of the converter is examined.The experiment result indicates the converter reaches the design requirement and it shows excellent performance.The converter system has been put into use safely.It is estimated that the AC - DC - AC converter system will be used in the drive systems for rolling mills in the near future.
基金funded by the Joint Fund Project of Shaanxi(Grant No.2021JLM-32)the General Project of National Natural Science Foundation of China(Grant No.52374346).
文摘The bottom blowing element is the key equipment to ensure the bottom blowing effect of the converter.Three types of bottom blowing elements,dispersive type(D1),double circular seam(D2)and straight cylinder type(D3),were built,and the effects of bottom blowing element type on molten bath flow,wall erosion and furnace bottom erosion were simulated.It was found that when the bottom blowing elements of dispersive type(D1)and double circular seam(D2)were used,the dead zone area in the lower part of the molten bath was smaller,and the high-speed zone area was larger;therefore,the stirring effect on the bottom melt was better.When the straight cylinder type(D3)bottom blowing element was used,the gas penetrated the molten bath at a faster rate to reach the surface of molten bath and failed to disperse in the bottom molten bath,and the wall shear stress near the nozzle outlet was larger.When argon was blown by three different bottom blowing elements,the area of the wall shear stress greater than 3 Pa was 4.8,5.6 and 8.7 cm2,respectively,within 0.2 m of the bottom blowing nozzle outlet.
文摘By measuring the volume concentration of SO<sub>2</sub> produced,blow rate of air（m<sup>3</sup>/min）Band converting times τ,the mathematical model of converting for oxidizing FeS and Cu<sub>2</sub>S,and that of controlling end point can be developed according to the slag making period andcopper making period,respectively.This derived model may be well suitable for either sideblow or top blow converter if the parameters-SO<sub>2</sub>B,τ.can be measured accurately.
