Based on the loose medium flow field theory, the loose top-coal drawing law of longwall top-coal caving（LTCC） mining technology is studied by using self-developed three-dimensional（3D） test device. The loose top-c...Based on the loose medium flow field theory, the loose top-coal drawing law of longwall top-coal caving（LTCC） mining technology is studied by using self-developed three-dimensional（3D） test device. The loose top-coal drawing test with shields and the controlled test without shields are performed in the condition without any boundary effect. Test results show that shields will cause reduction in drawing volume of coal in the LTCC mining. The deflection phenomenon of drawing body is also observed in the controlled test, which is verified that the deflection of drawing body is caused by shield. It is found that the deflection angle decreases with increasing caving height, with the maximum value of atailand the minimum value of 0. In addition, the formula to calculate the drawing volume is proposed subsequently.The deflection of drawing body is numerically simulated using particle flow code PFC3 Dand the proposed formula to calculate drawing volume in LTCC is also verified.展开更多
Discrete element calculations of the top-coal drawing process for diferent gangue-coal density ratios were conducted to investigate the efect of the gangue-coal density ratio on the drawing mechanism in longwall top-c...Discrete element calculations of the top-coal drawing process for diferent gangue-coal density ratios were conducted to investigate the efect of the gangue-coal density ratio on the drawing mechanism in longwall top-coal caving.The efects were analyzed for the drawing body,the top-coal boundary,and the recovery of top coal.The results show that for increasing density ratio,the initial drawing body on the goaf side is farther away from the drawing support and its width and volume gradually increase.The upper part of the sickle-shaped drawing body extends near the initial drawing body with increasing density ratio in the normal cycling stage,and the distance from the drawing body to the initial drawing body is its maximum width.The larger the density ratio,the smaller the height of the top coal above the goaf at the end of the initial drawing process.The height of the top-coal boundary decreases with increasing density ratio,until it reaches a limit.In a normal cycle,due to hysteretic development,the top-coal boundary moves toward the goaf until the density ratio is approximately 2.0,which is consistent with the physical experiment results.Finally,increasing the advance length of the working face is benefcial for increasing the overall recovery of top coal.展开更多
In order to explore the influence of different caving thicknesses on the MSS distributionand evolving characteristics of surrounding rocks in unsymmetrical disposal andfully mechanized top-coal caving (FMTC),based on ...In order to explore the influence of different caving thicknesses on the MSS distributionand evolving characteristics of surrounding rocks in unsymmetrical disposal andfully mechanized top-coal caving (FMTC),based on unsymmetrical disposal characteristics,the analyses of numerical simulation,material simulation and in-situ observation weresynthetically applied according to the geological and technical conditions of the 1151(3)working face in Xieqiao Mine.The results show that the stress peak value of the MSS-baseand the ratio of MSS-body height to caving thickness are nonlinear and inverselyproportional to the caving thickness.The MSS-base width,the MSS-body height,theMSS-base distance to working face wall and the rise distance of MSS-base beside coalpillar are nonlinear and directly proportional to the caving thickness.The characteristics ofMSS distribution and its evolving rules of surrounding rocks and the integrated cavingthickness effects are obtained.The investigations will provide lots of theoretic referencesto the surrounding rocks' stability control of the working face and roadway,roadway layout,gas extraction and exploitation,and efficiency of caving,etc.展开更多
Being a safe and highly-efficient mining method, fully mechanized mining with sublevel caving （FMMSC） was extensively employed in Chinese coal mines with thick seam. In order to make drawing top-coal furthest to par...Being a safe and highly-efficient mining method, fully mechanized mining with sublevel caving （FMMSC） was extensively employed in Chinese coal mines with thick seam. In order to make drawing top-coal furthest to parallel work with shearer cutting coal, decrease failure ratio of rear scraper conveyor and increase safe production capacity of equipments, based on production technology, set up the mating model of safe production capacity of equipments for the system of drawing top-coal and shearer cutting coal in coal face with sublevel caving. It is mean capability of drawing top-coal adapted to the capability of shearer cutting coal in a working circle in the coal face that was deduced. The type selection of equipment of rear scraper conveyor can be tackled with this mating model. The model was applied in FMMSC in Yangcun Coal Mine, Yima Coal Group of China. With the mating light-equipments, the coal output in coal face attained 1.05 Mt in 2004. It gained better technical-economic benefit.展开更多
基金financially supported by the Coal Joint Funds of the National Natural Science Foundation of China(No.U1361209)the National Basic Research Program of China(973 Program)(No.2013CB227903)
文摘Based on the loose medium flow field theory, the loose top-coal drawing law of longwall top-coal caving（LTCC） mining technology is studied by using self-developed three-dimensional（3D） test device. The loose top-coal drawing test with shields and the controlled test without shields are performed in the condition without any boundary effect. Test results show that shields will cause reduction in drawing volume of coal in the LTCC mining. The deflection phenomenon of drawing body is also observed in the controlled test, which is verified that the deflection of drawing body is caused by shield. It is found that the deflection angle decreases with increasing caving height, with the maximum value of atailand the minimum value of 0. In addition, the formula to calculate the drawing volume is proposed subsequently.The deflection of drawing body is numerically simulated using particle flow code PFC3 Dand the proposed formula to calculate drawing volume in LTCC is also verified.
基金supported by the Natural Science Foundation of China,China(Grant No.51904305)the Research Fund of the State Key Laboratory of Coal Resources and Safe Mining,China University of Mining and Technology(Grant No.SKLCRSM19KF023)+2 种基金the Fundamental Research Funds for the Central Universities(Grant No.2022YQNY03)the Research Fund of Key Laboratory of Safety and High-efficiency Coal Mining,Ministry of Education(Grant No.JYBSYS2021204)the Open Fund of State Key Laboratory of Coal Resources and Safe Mining(Grant No.SKLCRSM21KFA09).
文摘Discrete element calculations of the top-coal drawing process for diferent gangue-coal density ratios were conducted to investigate the efect of the gangue-coal density ratio on the drawing mechanism in longwall top-coal caving.The efects were analyzed for the drawing body,the top-coal boundary,and the recovery of top coal.The results show that for increasing density ratio,the initial drawing body on the goaf side is farther away from the drawing support and its width and volume gradually increase.The upper part of the sickle-shaped drawing body extends near the initial drawing body with increasing density ratio in the normal cycling stage,and the distance from the drawing body to the initial drawing body is its maximum width.The larger the density ratio,the smaller the height of the top coal above the goaf at the end of the initial drawing process.The height of the top-coal boundary decreases with increasing density ratio,until it reaches a limit.In a normal cycle,due to hysteretic development,the top-coal boundary moves toward the goaf until the density ratio is approximately 2.0,which is consistent with the physical experiment results.Finally,increasing the advance length of the working face is benefcial for increasing the overall recovery of top coal.
基金Supported by National Basic Research Program(973)(2005cb221503)National Natural Science Foundation of China(50674003)Science and Technological Fund of Anhui Province for Outstanding Youth(08040106839)
文摘In order to explore the influence of different caving thicknesses on the MSS distributionand evolving characteristics of surrounding rocks in unsymmetrical disposal andfully mechanized top-coal caving (FMTC),based on unsymmetrical disposal characteristics,the analyses of numerical simulation,material simulation and in-situ observation weresynthetically applied according to the geological and technical conditions of the 1151(3)working face in Xieqiao Mine.The results show that the stress peak value of the MSS-baseand the ratio of MSS-body height to caving thickness are nonlinear and inverselyproportional to the caving thickness.The MSS-base width,the MSS-body height,theMSS-base distance to working face wall and the rise distance of MSS-base beside coalpillar are nonlinear and directly proportional to the caving thickness.The characteristics ofMSS distribution and its evolving rules of surrounding rocks and the integrated cavingthickness effects are obtained.The investigations will provide lots of theoretic referencesto the surrounding rocks' stability control of the working face and roadway,roadway layout,gas extraction and exploitation,and efficiency of caving,etc.
文摘Being a safe and highly-efficient mining method, fully mechanized mining with sublevel caving （FMMSC） was extensively employed in Chinese coal mines with thick seam. In order to make drawing top-coal furthest to parallel work with shearer cutting coal, decrease failure ratio of rear scraper conveyor and increase safe production capacity of equipments, based on production technology, set up the mating model of safe production capacity of equipments for the system of drawing top-coal and shearer cutting coal in coal face with sublevel caving. It is mean capability of drawing top-coal adapted to the capability of shearer cutting coal in a working circle in the coal face that was deduced. The type selection of equipment of rear scraper conveyor can be tackled with this mating model. The model was applied in FMMSC in Yangcun Coal Mine, Yima Coal Group of China. With the mating light-equipments, the coal output in coal face attained 1.05 Mt in 2004. It gained better technical-economic benefit.
