期刊文献+
共找到403篇文章
< 1 2 21 >
每页显示 20 50 100
艺术设计专业课程思政实践:“1+N+X”模式探索
1
作者 岳明慧 郝锐 《设计艺术研究》 2024年第3期131-136,共6页
新时代背景下艺术设计专业课程思政的重要性日渐凸显,课程思政“1+N+X”教学模式的探索与实践,可以有效地实现“思政+艺术”的深度融合与价值创造。其中“1”代表跨学科的思政教学联盟,是协同推进课程和思政教育融合的基础;“N”指丰富... 新时代背景下艺术设计专业课程思政的重要性日渐凸显,课程思政“1+N+X”教学模式的探索与实践,可以有效地实现“思政+艺术”的深度融合与价值创造。其中“1”代表跨学科的思政教学联盟,是协同推进课程和思政教育融合的基础;“N”指丰富的思政元素库,提供多元的教学资源;“X”则涵盖多元化的教学方法和平台,增强教学的互动性和实效性。这3部分协同推进思政教育与艺术设计教学的深度结合,在促进学生全面发展的同时培养具有政治立场和艺术素养的人才,为艺术设计教育的改革提供新的方向和实践经验。 展开更多
关键词 艺术设计专业 课程思政 “1+n+X”模式 教学实践
下载PDF
基于nCode Design-Life的某车架疲劳可靠性分析 被引量:55
2
作者 李成林 宋莎莎 韩振南 《图学学报》 CSCD 北大核心 2014年第1期42-45,共4页
针对某型半挂牵引车车架局部出现裂纹或者断裂现象,通过有限元理论和疲劳分析理论相结合进行了车架的有限元分析和疲劳可靠性分析。首先对该车架进行了建模和有限元静态特性分析,然后定义了特定的时间载荷序列数据和材料参数,选用了S-N... 针对某型半挂牵引车车架局部出现裂纹或者断裂现象,通过有限元理论和疲劳分析理论相结合进行了车架的有限元分析和疲劳可靠性分析。首先对该车架进行了建模和有限元静态特性分析,然后定义了特定的时间载荷序列数据和材料参数,选用了S-N疲劳设计和静态疲劳分析方法,利用疲劳分析软件nCode Design-Life对该车架进行疲劳可靠性分析,得出该车架的疲劳结果云图和各节点的疲劳寿命,并从相关云图中确定出车架容易破坏的位置和其寿命之后再进行样车实验验证。 展开更多
关键词 车架 疲劳可靠性 S-n曲线 有限元 nCode design-Life
下载PDF
基于nCode Design-Life的电动客车车架疲劳寿命分析 被引量:14
3
作者 周美施 张铁柱 +2 位作者 尹怀仙 张洪信 刘高君 《青岛大学学报(工程技术版)》 CAS 2015年第4期96-100,共5页
针对某型电动客车车架疲劳及寿命问题,本文以有限元理论和疲劳分析理论相结合的方法,对电动客车车架进行静强度分析和疲劳寿命校核,建立有限元模型并进行受力分析,定义特定的载荷谱和材料疲劳数据;同时利用S-N静态疲劳设计方法,选用疲... 针对某型电动客车车架疲劳及寿命问题,本文以有限元理论和疲劳分析理论相结合的方法,对电动客车车架进行静强度分析和疲劳寿命校核,建立有限元模型并进行受力分析,定义特定的载荷谱和材料疲劳数据;同时利用S-N静态疲劳设计方法,选用疲劳分析软件nCode Design-Life对该车架进行疲劳可靠性分析。分析结果表明,该车架的疲劳寿命为1.558×106次,许用行驶里程为650 000km,与公交客运车行驶里程参考值约为400 000km相比,结果满足要求。该研究实现了电动车减重节能,增加了续驶里程,为车架优化设计及寿命模型的建立提供了理论依据。 展开更多
关键词 车架 疲劳强度 S-n曲线 有限元 nCode design-Life
下载PDF
Controllable design of Zn-Ni-P on g-C_3N_4 for efficient photocatalytic hydrogen production 被引量:13
4
作者 Yanbing Li Zhiliang Jin +1 位作者 Lijun Zhang Kai Fan 《Chinese Journal of Catalysis》 SCIE EI CAS CSCD 北大核心 2019年第3期390-402,共13页
Synthesizing a stable and efficient photocatalyst has been the most important research goal up to now. Owing to the dominant performance of g-C3N4 (graphitized carbonitride), an ordered assemble of a composite photoca... Synthesizing a stable and efficient photocatalyst has been the most important research goal up to now. Owing to the dominant performance of g-C3N4 (graphitized carbonitride), an ordered assemble of a composite photocatalyst, Zn-Ni-P@g-C3N4, was successfully designed and controllably prepared for highly efficient photocatalytic H2 evolution. The electron transport routes were successfully adjusted and the H2 evolution was greatly improved. The maximum amount of H2 evolved reached about 531.2 μmol for 5 h over Zn-Ni-P@g-C3N4 photocatalyst with a molar ratio of Zn to Ni of 1:3 under illumination of 5 W LED white light (wavelength 420 nm). The H2 evolution rate was 54.7 times higher than that over pure g-C3N4. Moreover, no obvious reduction in the photocatalytic activity was observed even after 4 cycles of H2 production for 5 h. This synergistically increased effect was confirmed through the results of characterizations such as XRD, TEM, SEM, XPS, N2 adsorption, UV-vis DRS, transient photocurrent, FT-IR, transient fluorescence, and Mott-Schottky studies. These studies showed that the Zn-Ni-P nanoparticles modified on g-C3N4 provide more active sites and improve the efficiency of photogenerated charge separation. In addition, the possible mechanism of photocatalytic H2 production is proposed. 展开更多
关键词 Zn-ni-P g-C3n4 H2 production Controllable design PHOTOCATALYST
下载PDF
基于nCode Design-Life的重型起重设备疲劳寿命预测研究 被引量:7
5
作者 李现春 胡晓兵 +1 位作者 李毅 徐营利 《机械》 2017年第8期1-6,共6页
为研究重型起重设备的疲劳损伤和寿命,以门式起重机为算例建立有限元模型,通过有限元静力学分析,最大等效应力位于跨中受拉区,得出门式起重机强度和刚度满足要求。采用nCode Design-Life疲劳仿真软件利用S-N疲劳设计方法对有限元静力学... 为研究重型起重设备的疲劳损伤和寿命,以门式起重机为算例建立有限元模型,通过有限元静力学分析,最大等效应力位于跨中受拉区,得出门式起重机强度和刚度满足要求。采用nCode Design-Life疲劳仿真软件利用S-N疲劳设计方法对有限元静力学特性和疲劳损伤进行分析,得到门式起重机疲劳寿命分布云图和疲劳损伤云图,其最小寿命满足工程要求。为了研究载荷变化对起重机寿命的影响,通过改变载荷缩放因子来改变时间载荷序列的大小,对比分析载荷变化后的寿命情况,得出随机载荷减小门式起重机寿命大大增加,过载对门式起重机的疲劳寿命有显著的影响。 展开更多
关键词 门式起重机 疲劳寿命 时间载荷序列 S-n曲线 nCodedesign-Life
下载PDF
Optimization study and design of scintillating fiber detector for DT neutron measurements on EAST with Geant4 被引量:1
6
作者 Wei-Kun Chen Li-Qun Hu +4 位作者 Guo-Qiang Zhong Bing Hong Rui-Jie Zhou Kai Li Li Yang 《Nuclear Science and Techniques》 SCIE EI CAS CSCD 2022年第11期33-45,共13页
Real-time monitoring of the 14-MeV D-T fusion neutron yield is urgently required for the triton burnup study on the Experimental Advanced Superconducting Tokamak (EAST). In this study, we developed an optimal design o... Real-time monitoring of the 14-MeV D-T fusion neutron yield is urgently required for the triton burnup study on the Experimental Advanced Superconducting Tokamak (EAST). In this study, we developed an optimal design of a fast-neutron detector based on the scintillating fiber (Sci-Fi) to provide D-T neutron yield through Geant4simulation. The effect on the detection performance is concerned when changing the number of the Sci-Fis embedded in the probe head, minimum distance between the fibers, length of the fibers, or substrate material of the probe head. The maximum number of scintillation photons generated by the n/γ source particles and output by the light guide within an event (event:the entire simulation process for one source particle) was used to quantify the n/γ resolution of the detector as the main basis. And the intrinsic detection efficiency was used as another evaluation criterion. The results demonstrate that the optimal design scheme is to use a 5 cm probe head whose substrate material is pure aluminum, in which 463 Sci-Fis with the same length of 5 cm are embedded, and the minimum distance between the centers of the two fibers is 2 mm. The optimized detector exhibits clear directionality in the simulation, which is in line with the expectation and experimental data provided in the literature. This study presents the variation trends of the performance of the SciFi detector when its main parameters change, which is beneficial for the targeted design and optimization of the Sci-Fi detector used in a specific radiation environment. 展开更多
关键词 Sci-Fi detector Optimal design n/c resolution Intrinsic detection efficiency GEAnT4
下载PDF
Design of flying vehicle control system by signal to noise ratio
7
作者 孙龙大 《Journal of Harbin Institute of Technology(New Series)》 EI CAS 2001年第1期63-68,共6页
Presents the new concept of ″Desired to be small″ based on the basic function of vehicle flight control system for an optimal design of flying vehicle control system, and the definition of S/N ratio and calculation ... Presents the new concept of ″Desired to be small″ based on the basic function of vehicle flight control system for an optimal design of flying vehicle control system, and the definition of S/N ratio and calculation formula for ″Desired to be small″ dynamic characteristics, and the S/N ratio method established for design of velicle flight control systems, by which, an orthogrnal table is used to arrange test schemes, and error facters are used to simulate various interferences, and the use of S/N ratio as a design criterion to synthesise the design of dynamic and static characteristics for definition of an optimal scheme, the application of S/N ratio method to the design of a type of vehicle control system and the single run success abtained in design of control system, technical evaluation test and design finalization flight test. 展开更多
关键词 S/n ratio method control system dynamic characteristics static characteristics parameter design
下载PDF
A rate-based method for dynamic analysis and optimal design of reactive extraction: n-Hexyl acetate esterification as an example 被引量:1
8
作者 Xutao Hu Hao Qin +3 位作者 Biao Hu Hongye Cheng Lifang Chen Zhiwen Qi 《Chinese Journal of Chemical Engineering》 SCIE EI CAS CSCD 2020年第1期76-83,共8页
The dynamic analysis and optimal design of reactive extraction are challenging due to high nonlinearity of model equations and tough decision of judging criteria. In this work, a dynamic rate-based method is developed... The dynamic analysis and optimal design of reactive extraction are challenging due to high nonlinearity of model equations and tough decision of judging criteria. In this work, a dynamic rate-based method is developed on g PROMS platform to get easy access to the solutions of reactive extraction with phase splitting. Based on rigorous criteria, dynamic analysis from initial state to final equilibrium(e.g., evolution of phase composition, mass transfer rate and reaction rate) and optimal design of operating conditions(e.g., extractant dosage and feed molar ratio) are achieved. To illustrate the method, the esterification of n-hexyl acetate is taken as an example. The approach proves to be reliable in the analysis and optimization of the exemplified system, which provides instructive reference for further process design and simulation of reactive extraction. 展开更多
关键词 REACTIVE extraction Dynamic rate-based method Optimal design Process simulation n-Hexyl ACETATE ESTERIFICATIOn
下载PDF
基于nCode design-life的某钢结构吊车梁疲劳可靠性 被引量:2
9
作者 巩玉发 贾凡 《辽宁工程技术大学学报(自然科学版)》 CAS 北大核心 2018年第2期371-375,共5页
近年来对吊车梁的调查显示,由于吊车梁的受力复杂,钢吊车梁在往复载荷作用下会提前出现不同程度的疲劳裂缝,危害生产安全与降低经济效益,疲劳寿命的研究可以有效的预防和减小破坏等问题的概率并可对于寿命进行延长.本文采用S-N方法,运用... 近年来对吊车梁的调查显示,由于吊车梁的受力复杂,钢吊车梁在往复载荷作用下会提前出现不同程度的疲劳裂缝,危害生产安全与降低经济效益,疲劳寿命的研究可以有效的预防和减小破坏等问题的概率并可对于寿命进行延长.本文采用S-N方法,运用ANSYS有限元软件与nCode Design-life疲劳软件相结合的方式,通过对目标吊车梁的实际受力状态进行模拟并对其进行疲劳可靠性分析,找出最易破坏的节点及最不利位置.取吊车梁一端为基准,设置电葫芦在吊车三个不同位置的工况进行分析,得出三组此破坏点的循环数据,其最小循环值则为吊车梁往复载荷后的最易损坏处. 展开更多
关键词 钢吊车梁 疲劳寿命 疲劳可靠性 循环数据 nCode design-life S-n方法
下载PDF
新型N形密封圈的设计及结构优化 被引量:2
10
作者 王琳 《液压气动与密封》 2023年第11期103-107,共5页
根据弹簧的弹性势能与动能相互转化原理以及弹簧的螺旋式结构,自主设计新型N形密封圈,通过ANSYS Workbench建立活塞杆、N形橡胶圈、沟槽的二维轴对称模型;利用正交试验法,以凹槽深度A(1,2,3,4 mm)、凹槽倒角B(0,0.1,0.3,0.5 mm)、凹槽间... 根据弹簧的弹性势能与动能相互转化原理以及弹簧的螺旋式结构,自主设计新型N形密封圈,通过ANSYS Workbench建立活塞杆、N形橡胶圈、沟槽的二维轴对称模型;利用正交试验法,以凹槽深度A(1,2,3,4 mm)、凹槽倒角B(0,0.1,0.3,0.5 mm)、凹槽间距C(0.6,0.8,1.0,1.2 mm)、预压缩量D(0.1,0.3,0.5,0.7 mm)为因素(水平),选择L 16(45)正交试验表,通过模拟,判断N形密封圈凹槽的最优几何参数,分析N形圈在静压密封状态下的密封性能,并与矩形圈和O形圈进行了对比研究。结果表明:压缩量0.7 mm(10%),凹槽深度3 mm,凹槽间距1.0mm,凹槽倒角0.3 mm为N形密封圈凹槽处最优几何参数;在介质压力低于7 MPa的情况下,新型N形密封圈比矩形圈和O形圈具有更小的Von-Mises应力和剪切应力,且在保证密封的前提下,接触压力较小,说明在静密封中,新型N形密封圈密封性能良好,使用寿命更长。研究结果对实际静密封工况下的使用具有理论指导意义。 展开更多
关键词 n形密封圈 结构优化 正交试验 设计
下载PDF
多点进水AAO-A+MBR工艺在低C/N污水处理厂的工程应用 被引量:4
11
作者 沈超 任玉辉 《净水技术》 CAS 2023年第1期168-173,共6页
海宁丁桥污水处理厂四期工程处理规模为5×10^(4)m^(3)/d,进水中工业废水占比高达50%,进水C/N较低。根据现有用地、进水指标及工艺运行情况,新建初沉发酵池+多点进水AAO-A+MBR工艺系统,采用多点进水耦合乙酸钠投加的多碳源分配脱氮... 海宁丁桥污水处理厂四期工程处理规模为5×10^(4)m^(3)/d,进水中工业废水占比高达50%,进水C/N较低。根据现有用地、进水指标及工艺运行情况,新建初沉发酵池+多点进水AAO-A+MBR工艺系统,采用多点进水耦合乙酸钠投加的多碳源分配脱氮保障方法,同时采用了将曝气池溶解氧控制在较低水平的策略。投入运行一年多,在进水COD_(Cr)、氨氮、TP、TN、SS平均质量浓度分别为254.0、29.30、3.09、31.60、126.3 mg/L的情况下,出水COD_(Cr)、氨氮、TP、TN、SS平均质量浓度分别为26.2、0.31、0.23、7.72、5.1 mg/L,出水水质稳定达到《城镇污水处理厂污染物排放标准》(GB 18918—2002)中的一级A标准,单位直接运行成本为0.5330元/m^(3),具有良好的环境效益和经济效益。 展开更多
关键词 污水处理厂 低碳氮比 多点进水 溶解氧 MBR工艺 工程设计
下载PDF
ON BALANCED n-ARY t-DESIGNS
12
作者 Guo Li-ming ( Department of Mathematics, Yunnan Teachers’ University ) 《红河学院学报》 1990年第4期19-27,共9页
A t-(v,k,λ)design(X,B)is a set X of points,of cardinality v,and a collection B of k-subsets of X called blocks,with the property that every t-subset of X is contained in precisely λ blocks.A t-design is a t-(v,k,λ)... A t-(v,k,λ)design(X,B)is a set X of points,of cardinality v,and a collection B of k-subsets of X called blocks,with the property that every t-subset of X is contained in precisely λ blocks.A t-design is a t-(v,k,λ) design for some v,k,γ.In this paper,we give a generalization of t-design called balanced n-ary t-design,and obtain some properties of the new combinatorial structure. 展开更多
关键词 BALAnCED n-ary T-designS InCIDEnCE STRUCTURE
下载PDF
A VIRTUAL MESH METHOD FOR THE OPTIMIZED DESIGN OF COMPLEX STRUCTURES
13
作者 Du Taisheng Huang Rongjie Song Tianxia Chen Chuanyao (College of Civil Engineering and Mechanics,Huazhong University of Science and Technology,Wuhan 430074,China) 《Acta Mechanica Solida Sinica》 SCIE EI 2003年第3期220-230,共11页
Concepts for a virtual 3D space and a hyper-sphere are proposed and the formulae for determining the computable nodes of the mesh are derived.Then a new optimization design method('Virtual Mesh Method'or V.M.M... Concepts for a virtual 3D space and a hyper-sphere are proposed and the formulae for determining the computable nodes of the mesh are derived.Then a new optimization design method('Virtual Mesh Method'or V.M.M)is developed.Three examples are given,showing that the method proposed is especially suitable for the optimized design of complex structures,and that the global approximate optimal solution can be searched with remarkably reduced computational work. 展开更多
关键词 virtual 3D space computable nodes n-D hyper-sphere optimization design virtual mesh method
下载PDF
在随机启动(p,N)-策略控制下不中断多重休假排队系统的性能分析
14
作者 袁雨梅 唐应辉 +1 位作者 刘雨欣 陈镰元 《应用数学》 北大核心 2023年第4期1069-1085,共17页
本文研究在随机启动(p,N)-策略控制下不中断多重休假的M/G/1排队模型.通过运用全概率分解技术和拉普拉斯变换工具,直接讨论了系统从任意初始状态出发在任意时刻t队长的瞬态分布,得到了队长瞬态分布的拉普拉斯变换表达式.基于瞬态分析,... 本文研究在随机启动(p,N)-策略控制下不中断多重休假的M/G/1排队模型.通过运用全概率分解技术和拉普拉斯变换工具,直接讨论了系统从任意初始状态出发在任意时刻t队长的瞬态分布,得到了队长瞬态分布的拉普拉斯变换表达式.基于瞬态分析,使用洛必达法则得到了系统在任意时刻t队长的稳态分布的递推表达式,同时求出了系统其他一些重要排队性能指标,如稳态队长分布的概率母函数、平均稳态队长和附加队长分布的显示表达式等,并讨论了一些特殊情形.最后,通过数值计算实例讨论了系统空闲率和附加平均队长关于一些参数的敏感性以及系统容量的优化设计. 展开更多
关键词 不中断多重休假 (p n)-策略 队长分布 全概率分解技术 系统容量设计
下载PDF
N-甲基甲酰胺和二乙二醇单甲醚的分离工艺设计
15
作者 苟蕾 《山西化工》 CAS 2023年第9期90-92,95,共4页
针对年处理50 t电镀废液中的N-甲基甲酰胺和二乙二醇单甲醚的分离工艺进行车间设计,确定其分离的基本工艺路线利用隔壁萃取精馏塔,多元醇作为萃取剂,对待分离体系进行萃取精馏分离,利用无机盐与酰胺类有机分子反应制成离子液体来处理N-... 针对年处理50 t电镀废液中的N-甲基甲酰胺和二乙二醇单甲醚的分离工艺进行车间设计,确定其分离的基本工艺路线利用隔壁萃取精馏塔,多元醇作为萃取剂,对待分离体系进行萃取精馏分离,利用无机盐与酰胺类有机分子反应制成离子液体来处理N-甲基甲酰胺。本设计期望能提高设计者的工程实践能力,对隔壁塔应用于实际生产有一定的探索意义。 展开更多
关键词 n-甲基甲酰胺 二乙二醇二甲基醚 萃取分离 车间设计
下载PDF
基于氧化偶联方法实现C(sp3)-N键构建的开放性实验设计
16
作者 吴际伟 王星宇 张婷 《广州化工》 CAS 2023年第1期290-291,296,共3页
基于现有有机合成科研平台,设计利用氧化偶联方法实现C(sp3)-N键构建的本科生开放性实验。在无催化剂的条件下,利用过硫酸钠为氧化剂实现二甲基亚砜C(sp3)-H键与苯并三氮唑N-H之间的脱氢氧化偶联反应来构建C(sp3)-N键。对该反应中催化... 基于现有有机合成科研平台,设计利用氧化偶联方法实现C(sp3)-N键构建的本科生开放性实验。在无催化剂的条件下,利用过硫酸钠为氧化剂实现二甲基亚砜C(sp3)-H键与苯并三氮唑N-H之间的脱氢氧化偶联反应来构建C(sp3)-N键。对该反应中催化剂、氧化剂和反应温度等条件进行了优化,确定了最优的反应条件。本开放性实验,将有机合成的新方法与有机波普分析融入实验教学,不仅开拓了学生的科研眼界,而且满足了学生个性化探索实践的需求。 展开更多
关键词 开放实验 教学活动设计 氧化偶联 C-n键构建
下载PDF
卡车(N类汽车)与M1类汽车除霜除雾系统布置和试验要求的差异化研究
17
作者 牙勇侯 吴方钰 王熙泉 《汽车科技》 2023年第3期52-57,共6页
本文主要论述汽车总布置设计中,参照标准法规对M1类汽车风窗玻璃除霜和除雾系统的性能和试验要求,根据N类汽(卡车)和M1类汽车人机系统的差异化,推导出N类汽车风窗玻璃除霜除雾区域的实际需求,以及N类汽车除霜除雾系统布置的关键要素,建... 本文主要论述汽车总布置设计中,参照标准法规对M1类汽车风窗玻璃除霜和除雾系统的性能和试验要求,根据N类汽(卡车)和M1类汽车人机系统的差异化,推导出N类汽车风窗玻璃除霜除雾区域的实际需求,以及N类汽车除霜除雾系统布置的关键要素,建立N类汽车除霜布置系统的理论体系,为N类汽车总布置设计中除霜系统布置提供理论依据。 展开更多
关键词 n类汽车 M1类汽车 除霜除雾 法规要求 除霜性能 总布置设计
下载PDF
固定床催化合成N,N,N′,N′-四甲基乙二胺的研究 被引量:3
18
作者 张涛 陈汉庚 +3 位作者 张旭 韦隆武 钱超 陈新志 《浙江大学学报(工学版)》 EI CAS CSCD 北大核心 2010年第12期2401-2405,共5页
通过自制备的金属负载型催化剂,以二甲胺和乙二醇为原料,在气固固定床反应器中合成了N,N,N′,N′-四甲基乙二胺.以γ-Al2O3为载体,Cu、Ni、Cr、Zn等金属为活性组分,通过浸渍法制备了3种二元金属负载型催化剂:Cu-Ni型、Cu-Zn型、Cu-Cr型... 通过自制备的金属负载型催化剂,以二甲胺和乙二醇为原料,在气固固定床反应器中合成了N,N,N′,N′-四甲基乙二胺.以γ-Al2O3为载体,Cu、Ni、Cr、Zn等金属为活性组分,通过浸渍法制备了3种二元金属负载型催化剂:Cu-Ni型、Cu-Zn型、Cu-Cr型.在相同条件下对3种催化剂的催化性能进行了考察,对乙二醇转化率及四甲基乙二胺的选择性进行了分析,结果表明:Cu-Ni型催化剂的催化效果最佳.通过平行实验对反应温度、胺醇的物质的量比及体积空速进行了研究,获得了较优的条件区间范围.根据平行实验结果,采用响应面实验设计方法(DesignEx-pert软件)对反应条件进行了优化,获得了最优的反应条件:以Cu-Ni为活性组分的催化剂进行催化,反应温度为204.81℃,胺醇的物质的量比为5.27,体积空速为0.29h-1,最佳产率可以达到79.84%. 展开更多
关键词 n n n n′-四甲基乙二胺 固定床反应器 金属负载催化剂 响应面方法 design EXPERT
下载PDF
Major factors controlling nitrous oxide emission and methane uptake from forest soil 被引量:3
19
作者 张秀君 陈冠雄 徐慧 《Journal of Forestry Research》 SCIE CAS CSCD 2001年第4期239-242,277,共5页
Soil samples were taken from depth of 0-12 cm in virgin broad-leaved Korean pine mixed forest in Changbai Moun-tain in July 2000. The effects of temperature, soil water content, pH, NH4+ and NO3- on N2O emission and C... Soil samples were taken from depth of 0-12 cm in virgin broad-leaved Korean pine mixed forest in Changbai Moun-tain in July 2000. The effects of temperature, soil water content, pH, NH4+ and NO3- on N2O emission and CH4 uptake of a for-est soil were studied in laboratory by the method of orthogonal design. It was observed under laboratory conditions in this study that there were significant correlations between N2O emission rate, CH4 oxidation rate, soil pH and temperature. Nevertheless, N2O emission rate also showed a significant positive correlation with CH4 oxidation rate. The results suggested that pH and temperature were important factors controlling N2O emission and CH4 oxidation under this experiment conditions. 展开更多
关键词 n2O emission CH4 uptake Orthogonal design Forest soil
下载PDF
A novel deep generative model for mRNA vaccine development: Designing 5′ UTRs with N1-methyl-pseudouridine modification 被引量:1
20
作者 Xiaoshan Tang Miaozhe Huo +16 位作者 Yuting Chen Hai Huang Shugang Qin Jiaqi Luo Zeyi Qin Xin Jiang Yongmei Liu Xing Duan Ruohan Wang Lingxi Chen Hao Li Na Fan Zhongshan He Xi He Bairong Shen Shuai Cheng Li Xiangrong Song 《Acta Pharmaceutica Sinica B》 SCIE CAS CSCD 2024年第4期1814-1826,共13页
Efficient translation mediated by the 5'untranslated region(5'UTR)is essential for the robust efficacy of mRNA vaccines.However,the N1-methyl-pseudouridine(m1)modification of mRNA can impact the translation ef... Efficient translation mediated by the 5'untranslated region(5'UTR)is essential for the robust efficacy of mRNA vaccines.However,the N1-methyl-pseudouridine(m1)modification of mRNA can impact the translation efficiency of the 5'UTR.We discovered that the optimal 5'UTR for m1y-modified mRNA(m1y-5'UTR)differs significantly from its unmodified counterpart,high-lighting the need for a specialized tool for designing mly-5'UTRs rather than directly utilizing high-expression endogenous gene 5'UTRs.In response,we developed a novel machine learning-based tool,Smart5UTR,which employs a deep generative model to identify superior m1y-5'UTRs in silico.The tailored loss function and network architecture enable Smart5UTR to overcome limitations inherent in existing models.As a result,Smart5UTR can successfully design superior 5'UTRs,greatly benefiting mRNA vaccine development.Notably,Smart5UTR-designed superior 5'UTRs significantly enhanced antibody titers induced by COVID-19 mRNA vaccines against the Delta and Omicron variants of SARS-CoV-2,surpassing the performance of vaccines using high-expression endogenous gene 5'UTRs. 展开更多
关键词 mRnA vaccine Machine learning 5'UTR mRnA design Sequence design n1-Methyl-pseudouridine COVID-19 SARS-CoV-2
原文传递
上一页 1 2 21 下一页 到第
使用帮助 返回顶部