The evolution of microstructure and microhardness was studied in a commercial tungsten-25%rhenium(mass fraction)(W-25Re)alloy processed by the high pressure torsion(HPT)procedure under a pressure of7.7GPa up to10revol...The evolution of microstructure and microhardness was studied in a commercial tungsten-25%rhenium(mass fraction)(W-25Re)alloy processed by the high pressure torsion(HPT)procedure under a pressure of7.7GPa up to10revolutions at different temperatures.The results show that the samples processed by10revolutions at room temperature could have the smallest grain size at around0.209μm.High saturation hardness(HV^1200)could be achieved after the rapid strengthening stage for samples processed by10revolutions both at room temperature and at573K.Microstructural observation and analysis from Hall-Patch relationship could reveal that grain refinement and grain boundaries strengthening are the main factors of hardening mechanism in W-25Re alloy.It is also demonstrated that sintered W-25Re sample may have brittle phase separation phenomenon after HPT processing.展开更多
The inhomogeneous hardness distribution of high pressure torsion (HPT) processed IF steel disks along different directions is investigated. The results indicated that there exists inhomogeneous distribution in HPT pro...The inhomogeneous hardness distribution of high pressure torsion (HPT) processed IF steel disks along different directions is investigated. The results indicated that there exists inhomogeneous distribution in HPT processed IF steel disks, giving lower hardness in the center and higher hardness in the edge regions. However, on the axisymmetrical section testing plane of the disks’ thickness direction, there is a soft zone near the surface of disks. Further results from radius testing plane of different depths from the surface of HPT processed disks show that the inhomogeneity rules of hardness distribution on the radius direction are similar to that on the thickness direction. Compared with the initial state, different stages of HPT (compression and compression + torsion) can both remarkably increase the hardness of IF steel disks. Microstructure investigation results can give a well support to verify the rules of hardness distribution, showing hardly no change of grains in center and sever plastic deformation in edge. The inhomogeneous distribution of stress and strain with the huge friction between anvil and disks in the process of HPT play an important role of hardness and microstructure distribution.展开更多
The Mg–Zn–Gd alloy with quasicrystal icosahedral phase was processed by high-pressure torsion (HPT). The effect of bimodal I-phase on the dynamic recrystallization was analyzed by transmission electron microscopy. T...The Mg–Zn–Gd alloy with quasicrystal icosahedral phase was processed by high-pressure torsion (HPT). The effect of bimodal I-phase on the dynamic recrystallization was analyzed by transmission electron microscopy. The results showed that the block I-phase can stimulate obvious particle-stimulated nucleation and dynamic recrystallization (DRX) grains were preferentially formed after HPT for 5 turns, while the granular I-phase only promoted the generation of sub-grains. The orientation relationship was determined as twofold//[1210] and fivefold//(0002)_(Mg). Moreover, after HPT for 9 turns, the DRX grains induced by block I-phase appeared to grow up and coarsened. Compared with block I-phase, the grains induced by granular I-phase presented much smaller size and distributed more homogeneous due to the strong pinning effect.展开更多
基金Project(11402264)supported by the National Natural Science Foundation of ChinaProject(BK20160182)supported by the Natural Science Foundation of Jiangsu Province,ChinaProjects(JUSRP116027,JUSRP51732B)supported by the Fundamental Research Funds from Jiangnan University,China
文摘The evolution of microstructure and microhardness was studied in a commercial tungsten-25%rhenium(mass fraction)(W-25Re)alloy processed by the high pressure torsion(HPT)procedure under a pressure of7.7GPa up to10revolutions at different temperatures.The results show that the samples processed by10revolutions at room temperature could have the smallest grain size at around0.209μm.High saturation hardness(HV^1200)could be achieved after the rapid strengthening stage for samples processed by10revolutions both at room temperature and at573K.Microstructural observation and analysis from Hall-Patch relationship could reveal that grain refinement and grain boundaries strengthening are the main factors of hardening mechanism in W-25Re alloy.It is also demonstrated that sintered W-25Re sample may have brittle phase separation phenomenon after HPT processing.
文摘The inhomogeneous hardness distribution of high pressure torsion (HPT) processed IF steel disks along different directions is investigated. The results indicated that there exists inhomogeneous distribution in HPT processed IF steel disks, giving lower hardness in the center and higher hardness in the edge regions. However, on the axisymmetrical section testing plane of the disks’ thickness direction, there is a soft zone near the surface of disks. Further results from radius testing plane of different depths from the surface of HPT processed disks show that the inhomogeneity rules of hardness distribution on the radius direction are similar to that on the thickness direction. Compared with the initial state, different stages of HPT (compression and compression + torsion) can both remarkably increase the hardness of IF steel disks. Microstructure investigation results can give a well support to verify the rules of hardness distribution, showing hardly no change of grains in center and sever plastic deformation in edge. The inhomogeneous distribution of stress and strain with the huge friction between anvil and disks in the process of HPT play an important role of hardness and microstructure distribution.
基金support from the National Natural Science Foundation of China(Grant Nos.51975175 and 52375329)the Projects of Natural Science Key Research of Anhui Province(2023AH051664).
文摘The Mg–Zn–Gd alloy with quasicrystal icosahedral phase was processed by high-pressure torsion (HPT). The effect of bimodal I-phase on the dynamic recrystallization was analyzed by transmission electron microscopy. The results showed that the block I-phase can stimulate obvious particle-stimulated nucleation and dynamic recrystallization (DRX) grains were preferentially formed after HPT for 5 turns, while the granular I-phase only promoted the generation of sub-grains. The orientation relationship was determined as twofold//[1210] and fivefold//(0002)_(Mg). Moreover, after HPT for 9 turns, the DRX grains induced by block I-phase appeared to grow up and coarsened. Compared with block I-phase, the grains induced by granular I-phase presented much smaller size and distributed more homogeneous due to the strong pinning effect.
