Discussion on the application prospect of the transient electromagnetic method based on the dual launcher and mine advanced detection

The dual transmitter implements the equivalent anti-magnetic flux transient electromagnetic method, which can effectively reduce the scope of the transient electromagnetic detection blind area. However, this method is rarely reported in the detection of pipelines in urban geophysical exploration and the application of coal mines. Based on this, this paper realizes the equivalent anti-magnetic flux transient electromagnetic method based on the dual launcher. The suppression effect of this method on the blind area is analyzed by physical simulation. And the detection experiment of underground pipelines is carried out outdoors. The results show that the dual launcher can significantly reduce the turn-off time, thereby effectively reducing the impact of the blind area on the detection results, and the pipeline detection results verify the device’s effectiveness. Finally, based on the ground experimental results, the application prospect of mine advanced detection is discussed. Compared with other detection fields, the formation of blind areas is mainly caused by the equipment. If the dual launcher can be used to reduce the blind area, the accuracy of advanced detection can be improved more effectively. The above research results are of great significance for improving the detection accuracy of the underground transient electromagnetic method.

3D forward modeling and response characteristics of low-resistivity overburden of the CFS-PML absorbing boundary for ground-well transient electromagnetic method

This study used the stable and convergent Dufort-Frankel method to differentially discretize the diffusion equation of the ground-well transient electromagnetic secondary field.The absorption boundary condition of complex frequency-shifted perfectly matched layer(CFS-PML)was used for truncation so that the low-frequency electromagnetic wave can be better absorbed at the model boundary.A typical three-dimensional(3D)homogeneous half-space model was established and a low-resistivity cube model was analyzed under the half-space condition.The response patterns and drivers of the low-resistivity cube model were discussed under the influence of a low-resistivity overburden.The absorption boundary conditions of CFS-PML significantly affected the low-frequency electromagnetic waves.For a low-resistivity cube around the borehole,its response curve exhibited a single-peak,and the extreme point of the curve corresponded to the center of the low-resistivity body.When the low-resistivity cube was directly below the borehole,the response curve showed three extreme values(two high and one low),with the low corresponding to the center of the low-resistivity body.The total field response of the low-resistivity overburden was stronger than that of the uniform half-space model due to the low-resistivity shielding effect of electromagnetic waves.When the receiving-transmitting distance gradually increased,the effect of the low-resistivity overburden was gradually weakened,and the response of the low-resistivity cube was strengthened.It was affected by the ratio of the overburden resistivity to the resistivity of the low-resistivity body.

Application of shallow high-resolution transient electromagnetic method( TEM) in geological investigation of debris flow

In the investigation of debris flow, the detection of the source area of the post-disaster debris flow is an important basis for evaluating the distribution of the debris flow accumulation layer and the subsequent control. In this paper, a shallow high-resolution TEM is used to detect the debris flow source area in Dashigou village, Yongji County, Jilin Province. The purpose of this investigation is to determine the depth range of debris flow damage. The detection results show that there is an obvious low resistance zone at about 10 m depth along the survey line, which is in good agreement with the drilling data and the high density electrical detection. It is proved that the depth is the maximum impact depth of the debris flow. The practical engineering proves that the method has high resolution in shallow layer detection, high efficiency and convenience in field acquisition. The maximum detection depth range of this method is 30--40 m, which meets the requirements of high efficiency and accurate detection for regional debris flow source area, and has high practical application value.

Mapping coalmine goaf using transient electromagnetic method and high density resistivity method in Ordos City, China

The research about subsurface characteristics by using transient electromagnetic method（TEM） and high density resistivity method（HDRM） were already conducted in Ordos. The objective of this research is to detect coalmine goaf areas based on rock resistivity. The data processing using wavelet transform, three point smoothing, RES2 DINV and Maxwell processing software to obtain 2D resistivity structure. The results showed that the layers with maximum resistivity values（30e33 U m on Line 1, 30e31 U m on Line 2, 32e40 U m on Line3） are founded at station 1e7, and 14e20 on Line 1,13e18 on Line 2, and 8e13 and 16e20 on Line 3 which is predicted as goaf layer, and the minimum resistivity values（20e26 U m of TEM, 45e75 U m of HDRM） at the other layers. This resistivity difference was caused by the geology and characteristics of the study area which is located close by the cleugh with rich coal, so the goaf area distinguishable with aquifer layer and coal seam. The results were also significant accidents and serious destruction of ecological environment.

Experiment in metal disturbance during advanced detection using a transient electromagnetic method in coal mines

Tunneling machines, or excavators, are large and good conductors and affect the reliability of data gathering and inter-pretation in advanced detection using transient electromagnetic methods. In our experiment, we used a coincident-loop and central loop type of configuration, where the coil plane 1) vertical to and 2) parallel to the working face. A SIROTEM instrument at differ-ent locations was used to observe the transient electromagnetic responses of the excavator and to analyze the response amplitudes. The result shows that the tunneling machine affects the advanced detection data and is related to the way the coil is coupled. When the excavator is 6 m from the observatory, the interference of tunneling machine can be ignored.

Application of Transient Electromagnetic Method with Multi-Radiation Field Sources in Deep Edge Mineral Resources Exploration

In recent years,in order to meet the practical needs of deep edge mine detection with large depth and high precision,transient electromagnetic method(TEM)near emission source detection mode has become an international advanced method(Xue et al.,2020).

A three-dimensional transient electromagnetic data inversion method based on a time–frequency transformation

Herein,a three-dimensional(3D)inversion method in the frequency domain based on a time–frequency transformation was developed to improve the efficiency of the 3D inversion of transient electromagnetic(TEM)data.The Fourier transform related to the electromagnetic response in the frequency and time domains becomes a sine or cosine transform under the excitation of downward-step current.We established a transformation matrix based on the digital fi ltering calculation for the sine transform,and then the frequency domain projection of the TEM data was determined from the linear transformation system using the smoothing constrained least squares inversion method,in which only the imaginary part was used to maintain the TEM data transformation equivalence in the bidirectional projection.Thus,the time-domain TEM inversion problem was indirectly and effectively solved in the frequency domain.In the 3D inversion of the transformed frequency-domain data,the limited-memory Broyden–Fletcher–Goldfarb–Shannoquasi–Newton(L-BFGS)method was used and modifi ed with a restart strategy to adjust the regularization parameter when the algorithm tended to a local minimum.Synthetic data tests showed that our domain transformation method can stably project the TEM data into the frequency domain with very high accuracy;furthe rmore,the 3D inversion of the transformed frequency-domain data is stable,can be used to recover the real resistivity model with an acceptable effi ciency.

Simplified Calculation Method for Transient Field of Transverse Electromagnetic Horn Antenna Used by High-altitude Electromagnetic Pulse Simulator

For conveniently calculating the radiated electric field of transverse electromagnetic(TEM) horn antenna,an approximate simplified analytical calculation method is suggested.This method divides the horn to a system of V-antennas and superimposes the fields of all V-antennas to obtain the field of the TEM horn.The method is compared with the traditional analytical method and numerical method.The obtained results suggest that the proposed method is valid,simple and that it can fastly calculate the radiated electric field of the TEM horn antenna in an arbitrary space with an arbitrary excitation voltage.Based on this method,radiation of the TEM horn antenna of a high-altitude electromagnetic pulse(HEMP) simulator is simulated.Rise time,pulse width,peak value of electric field,and field distribution are analyzed.Results show that the TEM horn antenna can be used in HEMP simulators: the near field waveform is closer to the standard waveform than to the far field waveform; the standards for the rise time and the peak value of electric field are easily satisfied; the pulse width of the radiated field can be increased by broadening the pulse width of an excitation source and by making the antenna of a proper

Prediction Technology of Buried Water-Bearing Structures in Coal Mines Using Transient Electromagnetic Method

Buried water-conducting and water-bearing structures in front of the driving head may easily lead to water bursts in coal mines. Therefore,it is very important for the safety of production to make an accurate and timely forecast about water bursts. Based on the smoke ring effect of transient electromagnetic fields,the principle of transient electro-magnetic method used in detecting buried water-bearing structures in coal mines in advance,is discussed. Small multi-turn loop configurations used in coal mines are proposed and a field procedure of semicircular sector scanning is presented. The application of this method in one coal mine indicates that the technology has many advantages compared with others. The method is inexpensive,highly accurate and efficient. Suggestions are presented for future solutions to some remaining problems.

Calculation of all-time apparent resistivity of large loop transient electromagnetic method with very fast simulated annealing

In large loop transient electromagnetic method(TEM),the late time apparent resistivity formula cannot truly reflect the geoelectric model,thus it needs to define the all-time apparent resistivity with the position information of measuring point.Utilizing very fast simulated annealing(VFSA) to fit the theoretical electromagnetic force(EMF) and measured EMF could obtain the all-time apparent resistivity of the measuring points in rectangular transmitting loop.The selective cope of initial model of VFSA could be confirmed by taking the late time apparent resistivity of transient electromagnetic method as the prior information.For verifying the correctness,the all-time apparent resistivities of the geoelectric models were calculated by VFSA and dichotomy,respectively.The results indicate that the relative differences of apparent resistivities calculated by these two methods are within 3%.The change of measuring point position has little influence on the tracing pattern of all-time apparent resistivity.The first branch of the curve of all-time apparent resistivity is close to the resistivity of the first layer medium and the last branch is close to the resistivity of the last layer medium,which proves the correctness of the arithmetics proposed.

Feasibility study of the transient electromagnetic method for chamber blasting misfire detection and recognition

In this paper,transient electromagnetic method was used to carry out the feasibility study on the detection and recognition of chamber blasting misfire.Firstly,an electromagnetic background field was established in the test;secondly,a benign conductor was preset in the chamber,and then the background field was eliminated after the electromagnetic field was measured;thirdly,the transient electromagnetic field was measured again after blasting;at last,the chamber blasting misfire was detected and recognized by comparing the change of eddy current field of the preset benign conductor before and after blasting.The test results showed that:When the buried depth of aluminum box target was no more than 30 m,transient electromagnetic method can clearly identify the position of the aluminum box;when the buried depth of aluminum box was more than30 m,the buried depth and position of the aluminum box was not sure due to the unknown level of secondary eddy current field generated by aluminum box.

Simulation research and application on response characteristics of detecting water-filled goaf by transient electromagnetic method

Water inrush disasters poses a great threat to the safe exploitation of coal resources.To solve this problem,the transient electromagnetic method(TEM)was proposed to accurately detect the water accumulation in the goaf.The electromagnetic response characteristics of diferent water-flled goaves were studied by electromagnetic feld theory,numerical simulation and feld verifcation.Through the models of 100%water accumulation,50%water accumulation,0%water accumulation,100%water accumulation with collapsed rock,50%water accumulation with collapsed rock and 0%water accumulation with collapsed rock goaf,the characteristics of induced voltage attenuation curves were studied.Meanwhile,the relationship between the attenuation voltage value and area of the transmitting coil,the depth of the goaf,the background resistivity,and the delay time were also simulated.The results illustrate that the attenuation curve of induced voltage presented a regular exponential decay form in the 0%water accumulation model but existed abnormal exaltation for voltage in water-flled model.Through the linear ftting curve,it can be seen that the abnormal intensity of the induced voltage becomes stronger as the distance between the measuring point and the center of the target decrement.Moreover,the abnormal amplitude of the induced voltage increases with the rise of the water accumulation and collapsed rock will weakly reduce the low-resistivity anomalous efect on the water-accumulated goaf.In addition,the response value of the attenuation voltage increased as the area of the transmitting coil increases,but decreased with increasing delay time and increasing background resistivity and depth of the target body.The feld detection results of the Majiliang coal mine also confrmed the theoretical analysis and the numerical simulation.

One-dimensional constrained inversion of electrical source transient electromagnetic method

The damped least squares inversion principle is applied to the transient electromagnetic one-dimensional inversion of electrical sources,and a new model is obtained by continuously iterating the initial model,thereby fitting the observed transient electromagnetic response,and performing one-dimensional inversion through induced electromotive force play.In this paper,in the damped least squares inversion,constraints are added to the Jacobian matrix,and simultaneous constraint equations and conventional inversion equations are solved.By weighting the constraint parameters,the difference between adjacent resistivities and layer thicknesses is minimized.Finally,K-type and H-type theoretical models were used to verify the reliability of the algorithm,and compared with the conventional transient electromagnetic damping least squares inversion.

Forward simulation of coal fire model by transient electromagnetic method with electrical source

Uncontrolled coal fires are natural disasters that may cause mineral loss and environmental damage.The traditional loop source transient electromagnetic method can effectively detect the low-resistivity region of coal fires,but its detection efficiency is not so good for high-resistivity regions.In view of this limitation,a technique based on electrical source transient electromagnetics is proposed in this paper to detect high-resistivity regions in the spontaneous combustion process of coal.Considering the complex geometry of the coal fire area,an unstructured tetrahedral grid is used in this study to realize the spatial discretization of the model,and solve the electromagnetic field based on a vector finite element algorithm.Numerical analysis is used to investigate methods for detecting coal fires and the characteristics of effective anomalies are further examined to provide guidance for practical detection.

不同模型约束的SOTEM稳定性反演

短偏移距瞬变电磁法(简称SOTEM)理论上探测精度较高,但由于地下电性结构复杂多样,目前所采用的单一模型约束反演策略具有局限性.本文提出了一种不同模型约束的SOTEM稳定性反演方案,能够快速获得具有光滑型、聚焦型、突变型结构特点的反演结果.该方案引入了光滑泛函、总变分泛函、最小梯度支撑泛函进行不同正则化,将不同稳定泛函重新构造,在统一反演框架下获得不同模型约束反演问题的解,并对正演、迭代过程、雅可比矩阵计算、正则化参数设置等多个细节进行了优化,以提高SOTEM反演的稳定性和效率.通过不同地电模型的大量样本,考察了本文所提的多种优化方案对反演的稳定性和效率的提升效果,对比了采用不同模型约束进行正则化的反演效果,从而验证了所提SOTEM反演方案的稳定性与快速有效性.

Detection technology and application of electromagnetic method for hidden danger of water gushing at coal face

The principles,methods,technologies and application effects of several electromagneticmethods for the detection of the hidden danger of water gushing at the coalface were introduced.Also,emphasis was laid on expounding the methods,principles andeffects of down-hole detections by electric transmission tomography and transient electromagneticmethod.The potential of point power supplied in the underground homogeneoussemi-space,as well as the response to a low-resistivity abnormal body in file hemogeneoussemi-space,was simulated by adopting 3-D finite element method to interpretthe basic theory of the electric transmission tomography.The results of actual measurementshow that the mine electromagnetic method is sensitive to water-bearinglow-resistivity bodies and can play a unique role in detecting the hidden danger of watergushing at the coal face.

EFFICIENT COMPUTATIONAL METHOD FOR TRANSIENT EM RESPONSE OF LARGE-LOOP SOURCE OVER LAYERED EARTH

Calculations of the ElectroMagnetic(EM) response produced by a large horizontal loop placed over layered medium are rather complex because its integral expression contains the product of two Bessel functions and has a divergent term. In this paper, an improved fast Hankel and Gaver-Stehfest transforms are introduced to solve the strong-oscillation and slow-decay properties of the integrand, where one Bessel function in the product is substituted by a carefully chosen polynomial of high accuracy and the other used as the digital filter coefficients in the convolution integral. Comparisons prove the validity and the efficiency of the proposed method.

Some issues on 2.5-D transient electromagnetic forward

Numerical calculation for two integral transforms in 2.5-D transient electromagnetic forward is a difficult and key task, namely, the inverse Fourier transform and the inverse Laplace transform. Some effective algorithms for them were described. Based on the known algorithms in DC resistivity on wave-number distribution and selection, we proposed a principle on how to choose the least wave-number concerning the central-loop transient electromagnetic method. First, observe the behavior of transformation function curve with regard to wave-number in Fourier domain. In the light of its asymptote, ascertain the coverage scope of wave-number. Compared with analytic solution, the least wave-number in Fourier domain can be derived. Furthermore, the Laplace numerical inversion algorithm which needs only a few Laplace variables in pure real domain was also introduced here. The procedure was applied to forward modeling on transient electromagnetic field of a vertical magnetic dipole over uniform half-space to demonstrate them effectiveness and general applicability.