Heat transfer enhancement in MOSFET mounted on different FR4 substrates by thermal transient measurement

Miniaturization of electronic package leads to high heat density and heat accumulation in electronics device, resulting in short life time and premature failure of the device. Junction temperature and thermal resistance are the critical parameters that determine the thermal management and reliability in electronics cooling. Metal oxide field effect transistor（MOSFET）is an important semiconductor device for light emitting diode-integrated circuit（LED IC） driver application, and thermal management in MOSFET is a major challenge. In this study, investigations on thermal performance of MOSFET are performed for evaluating the junction temperature and thermal resistance. Suitable modifications in FR4 substrates are proposed by introducing thermal vias and copper layer coating to improve the thermal performance of MOSFET. Experiments are conducted using thermal transient tester（T3ster） at 2.0 A input current and ambient temperature varying from25℃ to 75℃. The thermal parameters are measured for three proposed designs： FR4 with circular thermal vias, FR4 with single strip of copper layer and embedded vias, and FR4 with I-shaped copper layer, and compared with that of plain FR4 substrate. From the experimental results, FR4I-shaped shows promising results by 33.71% reduction in junction temperature and 54.19% reduction in thermal resistance. For elevated temperature, the relative increases in junction temperature and thermal resistance are lower for FR4I-shaped than those for other substrates considered. The introduction of thermal vias and copper layer plays a significant role in thermal performance.

Comprehensive analysis of two-dimensional charge transport mechanism in thin-film transistors based on random networks of single-wall carbon nanotubes using transient measurements

Understanding charge transport mechanisms in thin-film transistors based on random networks of single-wall carbon nanotubes(SWCNT-TFTs)is essential for further advances to improve the potential for various nanoelectronic applications.Herein,a comprehensive investigation of the two-dimensional(2D)charge transport mechanism in SWCNT-TFTs is reported by analyzing the temperature-dependent electrical characteristics determined from the direct-current and non-quasi-static transient measurements at 80-300 K.To elucidate the time-domain charge transport characteristics of the random networks in the SWCNTs,an empirical equation was derived from a theoretical trapping model,and a carrier velocity distribution was determined from the differentiation of the transient response.Furthermore,charge trapping and de-trapping in shallow-and deep-traps in SWCNT-TFTs were analyzed by investigating charge transport based on their trapping/de-trapping rate.The comprehensive analysis of this study provides fundamental insights into the 2D charge transport mechanism in TFTs based on random networks of nanomaterial channels.

Single-Shot Measurement of Transient Phase Shift Induced by Laser Wake

Based on the frequency-to-time mapping relation of the linearly chirped pulse, the temporal phase shift induced by a laser-excited wake in a helium gas jet is measured using a chirped-pulse spectral interferometry with ～ 140 fs resolution over a temporal region of I ps in a single shot. In this measurement, the image of the wake is obtained with one-dimensional spatial resolution and temporal resolution limited only by the bandwidth and chirp of the pulse. The ＇bubbles＇ feature of the wake structure, along with multiple wakes excited by the main lobe and the side lobe of a laser focal-spot, is captured simultaneously.

An experimental study of temperature and moisture content of wet porous materials under short-pulsed laser heating

The measurements of temperature and moisture content of a wet porous material were accomplished on the micro-seconds scale. The temperature wave was observed when the wet porous material was heated by short-pulsed laser with high power. It firstly revealed that the moisture content of wet porous material rapidly rises twice in one laser irradiation. The influences of laser parameters, the thickness and initial moisture content of the wet porous material on its temperature and moisture content were investigated.

Application of piezoelectric transient response in transducer acoustic power measurement

To explore a more convenient method for measuring the focused ultrasound power, a piezoelectric ceramic plate was used to receive ultrasonic signal directly. Due to an acoustic force acts on the surface of piezoelectric ceramic plate, the piezoelectric response was obtained by means of electromechanical analogy, which was composed of voltage response caused by forced vibration and high frequency attenuation response caused by natural vibration. The conversion relationship between output signal of piezoelectric ceramic plate and acoustic power of transducer was analyzed. The envelope of output piezoelectric signal was extracted in twice, and a voltage amplitude curve with sinusoidal distribution that could describe the changes of acoustic power was obtained. Under different drive voltage of transducer, the maximum peak voltage of envelope curve was found respectively. Their squared values were made a linear fitting with acoustic power measured by acoustic power meter, and then the proportional coefficient of theoretical relational expression was calibrated. The experimental results are in good agreement with the theory. The relative error between calibrated theoretical acoustic power and that measured by acoustic power meter was less than 8.7%. The paper can provide a guideline for measuring acoustic power of transducer by using piezoelectric signal.

Experimental investigation of transient characteristics of mild surge and diffuser rotating stall in a centrifugal compressor with vaned diffuser

The centrifugal compressor is widely used for gas compression in various industrial fields such as aero-engine, gas turbine and turbocharger. However, the stable operating range is usually restricted by the occurrence of flow instability such as stall and surge. The paper experimentally examines the developing process of surge and stall occurring in a centrifugal compressor to advance the understanding on flow mechanism of flow instability. It is found that three types of pressure fluctuation can be observed at low flowrate region. At the critical point, the local stall firstly occurs in some specific diffuser passages and the enlarged local diffuser stall eventually induces the mild surge of compression system indicated by the sinusoidal pressure fluctuation. At lower mass flow rate, the diffuser stall cell begins to circumferentially propagate along the impeller rotating direction at 11% of rotor speed with the existence of mild surge. In comparative analysis of IGV pre-swirl angle on the occurrence of mild surge, the mild surge still occurs at the operating condition when the slope of the characteristic map of test stage is still obviously negative, in which the compression system is supposed to be stable in previous study. And a new suggested criterion for the prediction of mild surge is demonstrated that the occurrence of mild surge depends on the destabilization effect of downstream components about diffuser and volute. Combined with the experimental data, the streamwise distribution characteristic of diffuser stall can be used to develop the simplified model of lumped parameters for the analysis on the generation mechanism of the diffuser rotating stall. The quantitative investigation on the relation between the pressure-rise characteristic of subcomponents and the occurrence of mild surge and diffuser rotating stall not only advances the prediction of stability limit but also lays the theoretic foundation for controlling these unsteady behaviors to improve the operating range.

Experimental Investigation on the Adiabatic Film Effectiveness for Counter-Inclined Simple and Laid-Back Film-Holes of Leading Edge

The adiabatic film effectivenessηof the counter-inclined film-holes fed by varying internal coolant intake on the turbine vane leading edge model was experimentally investigated.A semi-cylinder model was adopted to model the vane leading edge which was arranged with two-row holes,which located at±15°on both sides.The four Leading edge model with the combinations of hole-shape(simple holes and laid-back holes)and intake structure(plenum and impingement)were tested under four blowing ratios M of 0.5,1.0,1.5,and 2.0.Theηcontours were obtained by the transient measurement technique based on double thermochromic liquid-crystals.The results present that theηis sensitive to the M for the four studied leading edge cases.The addition of impingement enhances theηfor the two studied holes.The film jets make the coolant-flow closed to the target surface,resulting in higherηunder lower M.The core with higherηappears in the downstream area of hole-exit.Theηenhancement can be provided to almost the identical level by adding the impingement-holes and improving the hole-exit shaping in most areas.With increasing M,the jets with stronger exit normal momentum penetrate into the main-flow.The impingement addition may be a more effective program to upgrade theηrelatively to the exit shaping under larger M.Besides,the laid-back holes with impingement case produce the highest film cooling performance among the four cases,providing great potential in the leading edge especially under larger M.

Thermal analysis in high power GaAs-based laser diodes

The thermal characteristics of 808 nm Al Ga As/Ga As laser diodes（LDs） are analyzed via electrical transient measurements and infrared thermography. The temperature rise and thermal resistance are measured at various input currents and powers. From the electrical transient measurements, it is found that there is a significant reduction in thermal resistance with increasing power because of the device power conversion efficiency. The component thermal resistance that was obtained from the structure function showed that the total thermal resistance is mainly composed of the thermal resistance of the sub-mount rather than that of the LD chip, and the thermal resistance of the sub-mount decreases with increasing current. The temperature rise values are also measured by infrared thermography and are calibrated based on a reference image, with results that are lower than those determined by electrical transient measurements. The difference in the results is caused by the limited spatial resolution of the measurements and by the signal being captured from the facet rather than from the junction of the laser diode.

Characteristics of Long Air Gap Discharge Current Subjected to Switching Impulse

Measuring the pre-breakdown current of long sparks in air is important for investigating the discharge mechanism.Since the breakdown of long air gaps is conducted by a series of streamer-leader processes,the corresponding current signals cover a bandwidth of 0 to more than 20 MHz.Measurement accuracy of the current from the high voltage side is affected by the displacement current and impulse electromagnetic interference.In this paper,a coaxial current sensor with a DC bandwidth of 74.45 MHz is developed.A displacement current-restrained electrode structure is proposed to reduce the equivalent capacitance between the current sensor and the ground over 30 times.Combined with the digital optical fiber synchronous acquisition unit,a current measurement system for long air gap discharge is established.For the purpose of the UHV system’s external insulation optimization design,the discharge current waveform of a 6 m rod-plane air gap under positive switching impulse voltage with 250µs and 1000µs time to crest is obtained.Discharge images and stressed voltage are combined to analyze the continuous feature of a current waveform under critical time to crest impulse and discontinuous feature under long front duration impulse.For the purposes of a lightning protection study,the current waveform of a 10 m rod-plane air gap is subjected to negative switching impulse.Finally,the pulse characteristics of the current corresponding to the single channel and branching stepped negative leader are discussed.

Carbon dots/Bi_(2)WO_(6) composite with compensatory photo-electronic effect for overall water photo-splitting at normal pressure

Overall water photo-splitting is a prospective ideal pathway to produce ultra-clean H_(2) energy by semiconductors.However,the band structure of many semiconductors cannot satisfy the requirement of H_(2) and O_(2) production at the same time.Herein,we illustrate that carbon dots(CDs)/Bi_(2)WO_(6) photocatalyst with compensatory photo-electronic effect has enhanced activity for overall water photo-splitting without any sacrificial agent.In this complex photocatalytic system,the photo-potential provided by CDs makes the CDs/Bi2WO6(C-BWO)composite could satisfy the band structure conditions for overall water photo-splitting.The C-BWO composite(3 wt%CDs content)exhibits optimized hydrogen evolution(oxygen evolution)of 0.28μmol/h(0.12μmol/h)with an approximate 2:1(H_(2):O_(2))stoichiometry at normal pressure.We further employed the in-situ transient photovoltage(TPV)technique to study the photoelectron extraction and the interface charge transfer kinetics of this composite catalyst.