30Gbit/s Parallel Optical Receiver Module

A 30Gbit/s receptor module is developed with a CMOS integrated receiver chip（IC） and a GaAs-based 1 × 12 photo detector array of PIN-type. Parallel technology is adopted in this module to realize a high-speed receiver module with medium speed devices. A high-speed printed circuit board（PCB） is designed and produced. The IC chip and the PD array are packaged on the PCB by chip-on-board technology. Flip chip alignment is used for the PD array accurately assembled on the module so that a plug-type optical port is built. Test results show that the module can receive parallel signals at 30Gbit/s. The sensitivity of the module is - 13.6dBm for 10^-13 BER.

Switched-mode AGC circuits with internally created reset module for burst-mode unbalanced data optical receiver

This paper presents an innovative switched-mode auto gain control （AGC） circuit with internally created reset module for DC-10Mb/s burst-mode unbalanced （BMU） optical data transmission. Conventional AGC circuit is inappropriate for BMU data transmission because it is based on average level detection and requires considerable time to settle on a predefined gain. Therefore, we adopt a fast switched-mode AGC based on peak level detection. After the gain is adjusted, the peak level detectors need to re-detect the peak level of the input signal. Thus, we develop an internally created reset module. This AGC with reset module exhibits a fast operation and achieves an adjusted stable gain within one-bit, avoiding any bit loss up to 10Mb/s data rate. During power-up, the peak level detectors possibly hold an uncertain level resulting in the bit-errors. We propose a power-up reset circuit to solve this problem. Designed in a 0.5μm CMOS technology, the circuit achieves an optical sensitivity of better than -30dBm and a wide dynamic range of over 30dB with a power dissipation of only 30 mW from a 5V supply.

Downlink MBER Transmit Beamforming Design Based on Uplink MBER Receive Beamforming for TDD-SDMA Induced MIMO Systems

The downlink minimum bit error rate (MBER) transmit beamforming is directly designed based on the uplink MBER receive beamforming solution for time division duplex (TDD) space-division multiple-access (SDMA) induced multiple-input multiple-output (MIMO) systems, where the base station (BS) is equipped with multiple antennas to support multiple single-antenna mobile terminals (MTs). It is shown that the dual relationship between multiuser detection and multiuser transmission can be extended to the rank-deficient system where the number of users supported is more than the number of transmit antennas available at the BS, if the MBER design is adopted. The proposed MBER transmit beamforming scheme is capable of achieving better performance over the standard minimum mean square error transmit beamforming solution with the support of low-complexity and high power-efficient MTs, particularly for rank-deficient TDD-SDMA MIMO systems. The robustness of the proposed MBER transmit beamforming design to the downlink and uplink noise or channel mismatch is investigated using simulation.

A compact transmit/receive switch for 2.4 GHz reader-less active RFID tag transceiver

Radio frequency identification(RFID) is a ubiquitous identification technology nowadays. An on-chip high-performance transmit/receive(T/R) switch is designed and simulated in 0.13-μm CMOS technology for reader-less RFID tag. The switch utilizes only the transistor width and length(W/L) optimization, proper gate bias resistor and resistive body floating technique and therefore,exhibits 1 d B insertion loss, 31.5 d B isolation and 29.2 d Bm 1-d B compression point(P1d B). Moreover, the switch dissipates only786.7 n W power for 1.8/0 V control voltages and is capable of switching in 794 fs. Above all, as there is no inductor or capacitor used in the circuit, the size of the switch is 0.00208 mm2 only. This switch will be appropriate for reader-less RFID tag transceiver front-end as well as other wireless transceivers operated at 2.4 GHz band.

DESIGN OF INTERPOLATION FILTER FOR ALL DIGITAL RECEIVER-ON THE INTERPOLATION PROBLEM OF FULL RESPONSE MODULATION SIGNALS

All digital implementation of receiver is a main topic on digital communication recently. The design of interpolation filter is one of the important problems for all digital implementation of receiver. In this paper, for full response linear modulation signal, a interpolation criterion is proposed. An interpolation formula is presented on bandwidth-limited transmission signal. For example, using the raised cosine roll off function as the system pulse response, the feasibility and effectiveness on the interpolation formula are certified by theoretical and numerical analysis. The computer simulation result on 16-QAM signal is given.

Time Domain Analysis of Transmit/Receive Dipole Pair Array

We introduce a new transmit/receive dipole pair array to obtain a compact quasi\|monostatic antenna structure for ground penetrating radar systems. And we analyze this transmit/receive dipole pair array in time domain. The numerical results show that if the distance between the transmit antenna and receive antenna is appropriate the array configuration is adoptable.

ROBUST OPTIMIZATION OF TRANSMIT/RECEIVE BEAMFORMER FOR MIMO DOWNLINK WITH IMPERFECT CSI AT BASE STATION

A robust scheme is proposed to jointly optimize transmit/receive beamformers for Mul-tiple Input Multiple Output(MIMO) downlinks where the available Channel State Information(CSI) at Base Station(BS)(CSIBS) is imperfect.The criterion is to minimize the sum Mean Square Error(sum-MSE) over all users under a constraint on the total transmit power,which is a non-convex and non-linear problem.Observing from the first order optimization condition that the optimal trans-mit/receive beamformers are mutually dependent,the transmit/receive beamformers for each user are updated iteratively until the sum-MSE is minimized.Simulation results indicate that the proposed scheme can effectively mitigate the system performance loss induced by imperfect CSIBS.

Performance Analysis of Uplink Massive Spatial Modulation MIMO Systems in Transmit-Correlated Rayleigh Channels

In this paper,the performance of uplink multiuser massive multiple-input multipleoutput(MIMO)system with spatial modulation over transmit-correlated Rayleigh fading channel is investigated,where a large number of antennas are deployed at the base station and linear zero-forcing(ZF)receiver is employed for detection.By taking the transmit correlation and the randomness of shadow fading in to account,the bit error rate(BER)performance of the system is analyzed.According to the performance analysis,an approximated expression of overall average BER of the system is attained.Besides,asymptotic performance is studied and the corresponding BER expression at high signal-to-noise ratio is derived.On this basis,the diversity gain of the system can be obtained for performance evaluation.Simulation results show that the derived theoretical expressions match the simulated values well,which verifies the correctness of our analysis.

Cognitive anti-jamming receiver under phase noise in high frequency bands

This paper investigates the jamming sensing performance of the simultaneous transmit and receive based cognitive anti-jamming(SCAJ) receiver impaired by phase noise in local oscillators(LO) over fading channels. Firstly, energy detection(ED)based on the jamming to noise ratio(JNR) of the high frequency bands SCAJ receiver with phase noise under different channels is analyzed. Then, the probabilities of jamming detection and false alarm in closed-form for the SCAJ receiver are derived. Finally,the modified Bayesian Cramer-Rao bound(BCRB) of jamming sensing for the SCAJ receiver is presented. Simulation results show that the performance degradation of the SCAJ system due to phase noise is more severe than that due to the channel fading in the circumstances where the signal bandwidth(BW) is kept a constant. Moreover, the signal BW has an effect on the phase noise in LO, and the jamming detection probability of the wideband SCAJ receiver with lower phase noise outperforms that of the narrowband receiver using the same center frequency. Furthermore,an accurate phase noise estimation and compensation scheme can improve the jamming detection capability of the SCAJ receiver in high frequency bands and approach to the upper bound.

Experimental and numerical studies on the receiving gain enhancement modulated by a sub-wavelength plasma layer

A novel technique based on sub-wavelength plasma structure effects on enhancement of RF communication signals on a receiving antenna is carried out in this paper in laboratory experiments and analyzed by corresponding numerical simulations.Considerable intensification on receiving signal gain up to -10 d B in comparison with that without the plasma modulation is observed experimentally in -1 GHz RF band,with an effective enhancement bandwidth of -340 MHz and the fractional bandwidth of -34%.Then,the optimal modulation parameters of plasma are further studied by a numerical simulation.It is shown that the number density,the layer thickness,and the collision frequency of the plasma,as well as the relative distance between the plasma layer and antenna synergistically affect the modulation.Compared to the metallic antenna with the same overall dimension,the modulated antenna covered by the subwavelength plasma structure features higher receiving efficiency and lower radar cross section in the studied RF band.The mechanism of the reception enhancement is further revealed by analyzing characteristics of electromagnetic scattering and electric field distribution in the subwavelength plasma layer.The results then exhibit scientific significance and application potential of sub-wavelength plasma modulation on compact receiving antennas with higher performance and better feature of radar stealth.

Channel aware receiver for next generation wireless communication system

We consider an iterative phase synchronization scheme based on maximum a posteriori probability algorithm.In classical approaches,the phase noise estimation model considers one sample per symbol at the channel and receiver.However,information theoretic studies suggested use of more than one sample per symbol at the channel and receiver for achieving higher performance.In this article,a soft-information aided iterative receiver is derived,which uses off-the-shelf blocks for detection and demodulation by keeping the complexity of the receiver acceptable.We consider here two samples per symbols at the channel and receiver in a pragmatic paradigm.It is shown that phase noise estimation can be significantly improved at the expense of modest processing overhead.Simulation results are presented for low-density parity check coded quadrature amplitude modulations.Our results show a significant performance improvement for strong phase noise values compared to classical receiver approaches.

基于LoRa通信的无线发射台信号智能监测技术研究

为实现大面积无线发射台信号覆盖监测,有效地抵御监测过程中多径干扰和频率选择性衰减等干扰因素的影响,研究基于LoRa通信的无线发射台信号智能监测技术。在无线发射台发出信号后,转换成数字信号进行对比,识别出有效发射台信号后,通过级联型LoRa组网方式以及LoRa通信技术,将数据发送到服务器中存储,实现无线发射台信号的传输。利用循环位移因子对基带产生的Chirp信号完成调频扩频调制,扩展信号频谱,增强信号抗干扰能力以及传输可靠性,增强信号监测的效果。实验结果表明:该方法能够在距离LoRa终端设备2.5 km处依旧接收到发射台信号,丢包率为12%,能够准确地监测到无线发射台是否存在发射信号。

缓蚀剂对雷达T/R组件腐蚀行为的影响

T/R组件作为雷达系统的重要组成部分,在严酷海洋大气环境的侵蚀作用下,容易发生腐蚀,从而导致雷达系统性能下降,甚至引发故障。基于实测的某型机雷达舱环境数据,编制加速腐蚀试验环境谱,针对喷涂和未喷涂TFHS-20缓蚀剂的T/R组件开展当量加速腐蚀对比试验,并以收发通道芯片的微观腐蚀形貌、铝合金外壳蚀坑深度、T/R组件收发性能和输出功率等为指标参数,表征缓蚀剂对T/R组件腐蚀行为的影响。结果表明,TFHS-20缓蚀剂仅使T/R组件的输出功率降低0.59%~0.78%、接收增益降低0.11 dB~0.21 dB,缓蚀剂对T/R组件收发性能影响非常小。未喷涂缓蚀剂的T/R组件,在加速腐蚀试验的第4周期时,发射通道性能和接收通道功能失效;喷涂缓蚀剂的T/R组件,在加速腐蚀试验的8个周期时,接收通道功能失效。所以,TFHS-20缓蚀剂能够有效地提高T/R组件的使用寿命。

PCM信号间歇收发互补设计与回波重构方法

间歇收发用于辐射式仿真中可以有效解决收发信号互耦的问题,但间歇收发会带来信号损失,导致相位编码信号距离像出现高旁瓣。为了解决这一问题,提出间歇收发互补序列设计方法,给出了收发序列参数设计方法,并对相位编码间歇收发回波进行重组拼接,消除间歇收发导致的回波缺失,获得了精确的目标距离像。仿真结果表明,收发互补设计及回波重组拼接能够准确重构回波,并且重构后互相关系数接近1,验证了所提方法的可行性与正确性。

面向阵列级同时同频收发的宽带自干扰空域抑制

具备阵列级同时同频收发能力的多功能一体化平台,面临发射阵列对接收阵列的强自干扰问题。针对这一问题,该文设计了一种宽带自干扰空域抑制方法,构造了限制主波束增益损失条件下,最小化残余自干扰和噪声功率的非凸优化问题,提出了交替迭代的优化算法联合求解发射和接收数字波束成形系数,从理论上分析了所提算法的自干扰抑制极限性能,并给出了所提算法的计算复杂度。分析和仿真结果表明,给定2.4 GHz工作频率,100 MHz带宽,主波束增益损失限制在3 dB时,收发各30阵元的相控阵列宽带自干扰空域抑制能力,即有效各向同性隔离度达到168 dB,距离自干扰抑制性能极限差距7 dB。

250 kHz收发一体化水声换能器

针对水声领域对兼有高效发射和高灵敏度接收、收发工作频带重合、结构一体化高频水声换能器的应用需求,该文研制了一种高灵敏度收发一体水声换能器。该换能器由发射单元和接收单元两部分嵌套组成,发射单元采用1-3复合材料,接收单元采用单金属板压电陶瓷阵列结构。首先,通过有限元模拟确定发射和接收单元频率使其满足收发一体条件;其次接收单元采取改变压电陶瓷结构提升了机电耦合系数,从而提升接收灵敏度;最后制备了换能器样机并进行测试。结果表明,发射单元共振频率和接收单元反共振频均在250 kHz附近,接收灵敏度最高可达-173:5 dB,满足收发一体条件和高灵敏性能。

MCSEM勘探发射电流扰动实验仿真研究与设计

海洋可控源电磁法(MCSEM)勘探中发射电流质量是影响接收信号质量和勘探效率的重要因素。基于COMSOL Multiphysics虚拟仿真平台,研究了MCSEM勘探发射电流强度和形态参数对电场响应强度的影响。结果表明,发射电流强度的不稳定波动会降低接收信号的基波和谐波分量电场响应强度,主要影响中远偏移距电场值;发射电流波形的上升和下降沿的增加对接收信号基波和低次谐波分量影响较小,但会显著降低高次谐波分量的电场响应强度,主要影响中近偏移距电场值。通过仿真分析,MCSEM勘探中发射电流变化对接收信号的影响,可为实际勘探中发射波形异常时振幅随偏移距变化曲线的解释提供帮助。

水下双层加肋圆柱壳全空间收发分置散射声场快速预报方法

针对水下双层加肋圆柱壳的全空间收发分置散射声场求解,提出了一种快速预报方法。该方法将散射声场表示为声散射传递函数与声源密度函数的乘积,以目标表面网格信息、少量的仿真或测试多基地散射声压数据作为已知信息,借助数值积分、矩阵理论、最小二乘法对其他收发分置散射声场进行预报。分别以有限元仿真和试验测试的散射声压数据作为输入,对水下双层加肋圆柱壳的多基地散射声场进行了计算,并与完全采用有限元方法的计算结果进行了对比。结果表明:该方法在目标表面结构和部分散射声场数据已知条件下能对目标的全空间收发分置散射声场进行预报;已知散射声压数据量越多,计算频率越低,预报精度越高。

对调制识别网络隐身的雷达发射信号生成方法

雷达对抗场景中,电子侦察系统通过引入基于深度学习方法的智能脉冲调制识别网络,极大提升了对雷达信号的识别准确率。为了提高雷达信号的调制隐身抗识别能力,提出一种可以令深度识别网络错误预测的雷达发射信号生成方法。该方法首先通过短时傅里叶变换得到信号的时频谱;然后迭代生成携带调制隐身信息的时频谱;最后利用改进逆短时傅里叶变换得到时域调制隐身发射信号。该方法生成的雷达信号对以时频图为输入的调制识别网络隐身,并可实现回波信号的脉冲压缩处理。仿真结果验证了所生成信号的抗识别有效性、噪声鲁棒性和脉压可行性。