Effect of Various Field Shapers on Magnetic Pressure in Electromagnetic Inward Tube Forming

In this paper,the influence of various field shapers and their shapes on the distribution of the magnetic flux densities and applied forces on the work-piece in the electromagnetic inward tube forming are studied numerically using the FEA software MAXWELL.First the model was verified with experimental results and thereafter four kinds of field shapers(conical,cylindrical,concave and convex)were considered.Effects of their geometries,such as air gap between field shaper and tube work-piece,height of the step in single and multiple stepped field shaper on magnetic flux densities and magnetic pressures were studied.The results of this research can be applied to design field shaper,tube compression technology,and improve the efficiency of the coil.It is seen that magnetic force decreases if height of step in convex field shaper increases but effective forming region enlarges.Decreasing air gap has also a positive influence on magnetic field increase.Though the object of this research is limited to field shaper for inward tube forming,the results can also be applied to the field shaper for tube bulging.

Viscous Inner and Outer Pressure Forming Method of Thin-walled Tube and Its Application

Aiming at overcoming the difficulties in integral forming of thin-walled tubes with complex shapes, a novel forming method by inner and outer pressure through viscous was proposed. In this method, by dividing large deformation of the part into inner and outer pressure forming deformations, the limit deformation of tube part can be increased by several times. Meanwhile, the principle of viscous inner and outer pressure forming was provided, and key problems during the forming process such as reduction of the wall-thickness and instability wrinkling were analyzed. Thereby, the complex curved surface super-alloy GH3044 thin-walled tube with varying diameter ratio of 1.35（the ratio between the maximum and minimum diameters of the part） can be integrally formed by this method. The experimental surface of the formed part is superior in quality and the wall-thickness distribution is uniform. The results show that the viscous inner and outer pressure forming can provide a new approach for integral forming of thin-walled tubes with complex shapes.

Effect of Deformation Condition on Axial Compressive Precision Forming Process of Tube with Curling Die

The effect of the deformation condition on the axial compressive precision forming process of tube with curling die was investigated by using a rigid-plastic FEM. The results show that the forming accuracy depends mainly on geometric condition rp/d0, little on tube material properties and friction condition; the relative gap △/2rp of double-walled tubes obtained decreases with Increasing rp/d0, and there is a parameter k for a given to/do or rp/t0, when rp/d0 >k, △/2rp< 1, otherwise △/2rp>1.

A Study on 3D FE Simulation Method of NC Bending Process of Thin-walled Tube

The numerical control (NC) precision bending process of thin-walled tube is on e of advanced plastic forming processes with high efficiency, forming precision, strength/weight ratio and low cost, thus it is playing more and more important role in manufacturing parts in aerospace and automobile industries. However, the determination of parameters crucial to make sure tube parts qualified is heavil y experience-based and involves repeated trial-and-errors in practice, which makes the production efficiency reduce drastically and does not fulfill the deve lopment of high technology. With quick development of computer technology and gr adual perfect of plastic forming theory, computer numerical simulation based on finite element method (FEM) has become one of important tools of researching and developing plastic forming technology. Development trend of NC precision bendin g process of tube is simulating its forming process by FEM. Because NC tube bend ing is of 3D nature, it is of great importance to analyze the forming mechanism and find out the influence law of forming parameters on forming process in the N C precision bending process of thin-walled tube quantitatively by 3D FE simulat ion. Based on the rigid-plastic finite element method (FEM) principle, a 3-dimens ional (3D) rigid-plastic FE simulation system named TBS -3D (tube bending simu lation by 3D FEM) for the NC bending process of thin-walled tube has been devel oped, a reasonable FEM model has been established. By use of this FEM simulation system, a NC bending process of thin-walled has been simulated. And deformed m eshes under different bending stages, stress distribution along bending directio n, relationship between maximal wall thickness changing ratio and bending angle have been obtained. And then some forming laws of NC tube bending obtained are a s follows: (1) NC bending process make tube elongate to some extent; (2) Charact eristic of stress distribution is that the outer area is undergoing tensile stre ss, the inner area is undergoing compression stress, and stress neutral layer mo ves close to the inner area, which is in good accordance with the practice; (3) Maximal wall thinning ratio in the outer tensile area changes only a little with increase of bending angle, and maximal wall thickening ratio in the inner compr ession area increases linearly with bending angle. The above results show that 3 D FE simulation is an important and valid tool of analyzing NC bending process o f tube, this research is beneficial for the practical tube bending process, and it may serve as a significant guide to the practice of the relevant processes.

Effect of microstructure on outer surface roughening of magnesium alloy tubes in die-less mandrel drawing

The crystal orientation and outer surface roughening of magnesium alloy tubes were evaluated to clarify the effect of the mandrel on the microstructure and outer surface roughness in die-less mandrel drawing. Locally heated ZM21 tubes with an outer diameter of 6.0 mm and an inner diameter of 3.8 mm were drawn with and without a mandrel. The outer surface roughness and crystal orientation were evaluated in the same measurement area. The results indicated that the outer surface becomes rougher in the die-less mandrel drawing than in die-less drawing for a given outer circumferential strain. The outer surface roughness developed when there was large difference in the pyramidal slip system Schmid factor. Therefore, the slip deformation of the pyramidal slip system seems to be mainly responsible for the outer surface roughening in the die-less mandrel drawing. Furthermore, the crystal grain with the {2110} crystal plane vertical to the normal direction of outer surface had a larger Schmid factor than the other crystal grains. The large number of crystal grains with the {2110} crystal plane in the die-less mandrel drawing is one of the reasons that the outer surface roughness develops more in the die-less mandrel drawing than in die-less drawing for a given outer circumferential strain. These results will contribute significantly to the development of fabrication process of the microtube with high surface quality, which prevents rapid corrosion of biomedical applications.