期刊文献+
共找到1,775篇文章
< 1 2 89 >
每页显示 20 50 100
Metallurgical Forensics: Investigating a Superheater Tube Failure in Industrial Process Plants
1
作者 Kok Toong Leong 《World Journal of Engineering and Technology》 2024年第3期742-758,共17页
A metallurgical forensic investigation was conducted to determine the cause of a failed superheater tube. Analysis techniques by Visual Examination, Energy Dispersive X-ray Analysis, Mechanical Testing and Metallograp... A metallurgical forensic investigation was conducted to determine the cause of a failed superheater tube. Analysis techniques by Visual Examination, Energy Dispersive X-ray Analysis, Mechanical Testing and Metallographic Investigation were conducted, together with a comparative study from an inlet elbow section that did not fail. The superheater tube suffered premature failure after being in service for about two years. It was concluded that the failed tube underwent overheating, corrosion-erosion, embrittlement, and eventual failure under its internal pressure by stress rupture. The analysis revealed intergranular cracks, window fracture features and spheroidization of pearlite with grain growth. A possible contribution to embrittlement was from copper. Follow-ups and recommendations were provided, as well as covering materials, inspection, and operational considerations. 展开更多
关键词 Superheater tubes Thermal Degradation Corrosion-Erosion EMBRITTLEMENT stress Rupture
下载PDF
A STUDY ON THE EFFECT OF RADIAL INERTIA ON THE ELASTO-PLASTIC COMBINED STRESS WAVE PROPAGATION IN THIN-WALLED TUBES 被引量:2
2
作者 Li Yongchi Huang Chengyi Yuan Fuping Jin Yongmei 《Acta Mechanica Solida Sinica》 SCIE EI 2001年第1期58-66,共9页
An in-depth analysis of propagation characteristics ofelasto-plastic combined stress waves in circular thin-walled tubeshas been made. In obtaining the simple-wave solution, however, mostresearches have ignored the in... An in-depth analysis of propagation characteristics ofelasto-plastic combined stress waves in circular thin-walled tubeshas been made. In obtaining the simple-wave solution, however, mostresearches have ignored the influence of the circumferential stressrelated to the radial inertial ef- fect in the tubes. In this paperthe incremental elasto-plastic constitutive relations which areconve- nient for dynamic numerical analysis are adopted, and thefinite-difference method is used to study the evolution adpropagation of elasto-plastic combined stress waves in a thin-walledtube with the radial inertial effect of the tube considered. Thecalculation results are compared with those obtained when the radialinertial effect is not considered. The calculation results show thatthe radial inertial effect of a tube has a fairly great influence onthe propagation of elasto-plastic combined stress waves. 展开更多
关键词 circular thin-walled tube elasto-plastic combined stress waves radialinertial effect
下载PDF
THE INFLUENCE OF RESIDUAL STRESS ON THE CORROSION RESISTANCE OF H68A BRASS TUBES IN SEA WATER 被引量:1
3
作者 Yan, Yumin Zhu, Xiaolong Lin, Leyun Beijing General Research Institute for Nonferrous Metals, Beijing 100088, China 《中国有色金属学会会刊:英文版》 CSCD 1993年第1期62-65,共4页
This paper reveals the morphological characteristics of the cracks formed in H68A brass tubes fully immersed in seawater, and studies the depth profiles of the residual stress of the tubes. Tbe great residual stress i... This paper reveals the morphological characteristics of the cracks formed in H68A brass tubes fully immersed in seawater, and studies the depth profiles of the residual stress of the tubes. Tbe great residual stress in the wall results in stress-corrosion cracking, and the unique morphology of the cracks is due to the uneven distribution of residual stress through the depth of the tube. 展开更多
关键词 RESIDUAL stress Corrosion resistance H68A bruss tube Seawater
下载PDF
Linear and nonlinear torsional free vibration of functionally graded micro/nano-tubes based on modified couple stress theory 被引量:2
4
作者 A.R.SETOODEH M.REZAEI M.R.ZENDEHDEL SHAHRI 《Applied Mathematics and Mechanics(English Edition)》 SCIE EI CSCD 2016年第6期725-740,共16页
The linear and nonlinear torsional free vibration analyses of functionMly graded micro/nuno-tubes (FGMTs) are analytically investigated based on the couple stress theory. The employed non-classical continuum theory ... The linear and nonlinear torsional free vibration analyses of functionMly graded micro/nuno-tubes (FGMTs) are analytically investigated based on the couple stress theory. The employed non-classical continuum theory contains one material length scale parameter, which can capture the small scale effect. The FGMT model accounts for the through-radius power-law variation of a two-constituent material. Hamilton's principle is used to develop the non-classical nonlinear governing equation. To study the effect of the boundary conditions, two types of end conditions, i.e., fixed-fixed and fixed-free, are considered. The derived boundary value governing equation is of the fourthorder, and is solved by the homotopy analysis method (HAM). This method is based on the Taylor series with an embedded parameter and is capable of providing very good approximations by means of only a few terms, if the initial guess and the auxiliary linear operator are properly selected. The analytical expressions are developed for the linear and nonlinear natural frequencies, which can be conveniently used to investigate the effects of the dimensionless length scale parameter, the material gradient index, and the vibration amplitude on the natural frequencies of FGMTs. 展开更多
关键词 torsional vibration nonlinear vibration micro/nano-tube functionallygraded material (FGM) couple stress theory size effect
下载PDF
ANALYSIS OF TRANSIENT THERMAL STRESS IN CYLINDRICALLY ORTHOTROPIC TUBES
5
作者 凌道盛 《Applied Mathematics and Mechanics(English Edition)》 SCIE EI 2003年第12期1398-1402,共5页
The incorrect deduction of equations in the research works devoted to the studies of transient stress in cylindrically orthotropic tubes and done by Kardomateas (Journal of Applied Mechanics, 1989, 1990) leads to the ... The incorrect deduction of equations in the research works devoted to the studies of transient stress in cylindrically orthotropic tubes and done by Kardomateas (Journal of Applied Mechanics, 1989, 1990) leads to the wrong results. The errata (1991) correct the deduction error, but do not give the right numerical results. All errors are corrected, and the Mathematica is adopted to solve the large argument problem for Bessel function. A theoretical solution of the transient thermal stresses in tubes with uniform form is presented, and a numerical example is studied. 展开更多
关键词 cylindrically orthotropic transient thermal stress composite tube
下载PDF
THE APPLICATION OF BOUNDARY ELEMENT METHOD IN STRESS ANALYSIS OF AUTOFRETTED TUBE WITH NOTCH
6
作者 宋顺成 张玉诚 冯德振 《Applied Mathematics and Mechanics(English Edition)》 SCIE EI 1990年第2期185-190,共6页
In this paper, the boundary element method is applied to investigate the internal state of stress of autofretted tube with notch and the calculated results are important in the practical design.
关键词 THE APPLICATION OF BOUNDARY ELEMENT METHOD IN stress ANALYSIS OF AUTOFRETTED tube WITH NOTCH
下载PDF
Combined stress waves with phase transition in thin-walled tubes 被引量:5
7
作者 宋卿争 唐志平 《Applied Mathematics and Mechanics(English Edition)》 SCIE EI 2014年第3期285-296,共12页
The incremental constitutive relation and governing equations with combined stresses for phase transition wave propagation in a thin-walled tube are established based on the phase transition criterion considering both... The incremental constitutive relation and governing equations with combined stresses for phase transition wave propagation in a thin-walled tube are established based on the phase transition criterion considering both the hydrostatic pressure and the deviatoric stress. It is found that the centers of the initial and subsequent phase transition ellipses are shifted along the sigma-axis in the sigma tau-plane due to the tension-compression asymmetry induced by the hydrostatic pressure. The wave solution offers the 'fast' and 'slow' phase transition waves under combined longitudinal and torsional stresses in the phase transition region. The results show some new stress paths and wave structures in a thin-walled tube with phase transition, differing from those of conventional elastic-plastic materials. 展开更多
关键词 combined stress phase transition wave thin-walled tube shape memory alloy(SMA)
下载PDF
Stress Analysis of the Glass Bulb of 35-inch(V)120°Color Picture Tube
8
作者 童林夙 TorongeyPeterKimanus 《Journal of Southeast University(English Edition)》 EI CAS 1996年第2期53-56,共4页
A simulation of the stress analysis for a vacuum glass bulb of 35 inch (V) 120° Color Picture Tube(CPT) has been developed. It is shown that extra large deflection angle Color Picture Tube is viable. Increase ... A simulation of the stress analysis for a vacuum glass bulb of 35 inch (V) 120° Color Picture Tube(CPT) has been developed. It is shown that extra large deflection angle Color Picture Tube is viable. Increase in the deflection angle will shorten the de 展开更多
关键词 FEM VACUUM stress analysis color PICTURE tube EXTRA large DEFLECTION angle GLASS BULB
下载PDF
裂解炉稀释蒸汽管道三通开裂原因分析
9
作者 陈静 孔范洋 +1 位作者 许铁群 陈怀宁 《压力容器》 北大核心 2024年第7期56-62,86,共8页
针对某乙烯裂解装置稀释蒸汽管道304H耐热不锈钢三通使用1年后发生开裂的情况,从材料成分、力学性能、金相组织、残余应力和断口特性等方面进行了分析。结果表明,裂纹分别启裂于三通的内壁和外壁,多数裂纹开裂处伴有晶间腐蚀特征,裂纹... 针对某乙烯裂解装置稀释蒸汽管道304H耐热不锈钢三通使用1年后发生开裂的情况,从材料成分、力学性能、金相组织、残余应力和断口特性等方面进行了分析。结果表明,裂纹分别启裂于三通的内壁和外壁,多数裂纹开裂处伴有晶间腐蚀特征,裂纹扩展特性以沿晶型为主;断口附近腐蚀产物存在O,S,Cl等酸性腐蚀介质。三通主管表面最大轴向应力达到147 MPa,三通相贯线附近距裂纹20 mm处的最大环向应力达到114 MPa,说明运行中的三通表面应力达到了材料屈服强度的1/2。分析认为,裂纹的产生是由于材料发生敏化后,在应力和腐蚀介质共同作用下形成的以沿晶为主的应力腐蚀开裂,更换三通材料或通过适当的固溶处理降低三通中的残余应力是避免三通开裂的重要途径。 展开更多
关键词 稀释蒸汽管道 三通 应力腐蚀开裂 304H不锈钢 敏化
下载PDF
P110S钢级油管管体断裂原因
10
作者 赵映辉 夏文斌 +1 位作者 周勇 赵建明 《理化检验(物理分册)》 CAS 2024年第4期68-71,共4页
某油井P110S钢级油管接箍下方8 m位置处发生断裂,采用宏观观察、化学成分分析、金相检验、扫描电镜和能谱分析、X射线衍射分析等方法对油管断裂原因进行分析。结果表明:该批油管力学性能不稳定,油管断口上的腐蚀产物主要为FeS;油管的强... 某油井P110S钢级油管接箍下方8 m位置处发生断裂,采用宏观观察、化学成分分析、金相检验、扫描电镜和能谱分析、X射线衍射分析等方法对油管断裂原因进行分析。结果表明:该批油管力学性能不稳定,油管断口上的腐蚀产物主要为FeS;油管的强度较高、使用温度较低且质量较大,导致油管内部形成硫化物应力腐蚀开裂。 展开更多
关键词 P110S钢级油管 硫化物 应力腐蚀开裂 力学性能 显微组织
下载PDF
内衬GFRP防护复合管壁原缺陷坑处应力重分布规律分析
11
作者 卢召红 彭郑飞 王佳美 《河北工程大学学报(自然科学版)》 CAS 2024年第1期90-96,共7页
为了深入研究内衬GFRP防护复合管壁在其原管道内腐蚀缺陷坑处的应力重分布状态以及其修复的效果,利用弹塑性力学中的平衡微分方程,建立了管道内腐蚀缺陷处的数学模型,采用有限单元法建立了含单个腐蚀缺陷的管道模型,并通过改变腐蚀缺陷... 为了深入研究内衬GFRP防护复合管壁在其原管道内腐蚀缺陷坑处的应力重分布状态以及其修复的效果,利用弹塑性力学中的平衡微分方程,建立了管道内腐蚀缺陷处的数学模型,采用有限单元法建立了含单个腐蚀缺陷的管道模型,并通过改变腐蚀缺陷坑的深厚比,将修复前后腐蚀缺陷坑处的应力状态进行对比分析。分析结果表明,腐蚀缺陷坑的深厚比对管道的应力分布有着显著的影响,所以在进行管道安全评估时应注意腐蚀坑深度的影响;在腐蚀缺陷坑深厚比0.1到0.8的分次增加的过程中,管壁腐蚀缺陷处的周向应力,径向应力,Mises应力都有增大的趋势;修复前腐蚀缺陷坑处的周向应力和Mises应力相近,径向应力较前两者小,三者中周向应力最大;在修复前后,管道腐蚀缺陷处的控制应力一般是周向应力,管道的失效可依据周向应力进行判断;修复后的内衬GFRP防护复合管壁,原始腐蚀缺陷坑处发生了应力重分布,其周向应力与Mises应力均有减小,修复效果明显。 展开更多
关键词 腐蚀缺陷坑 GFRP防护层 复合管 应力重分布
下载PDF
Expansive Performance of Self-stressing and Self-compacting Concrete Confined with Steel Tube
12
作者 徐磊 《Journal of Wuhan University of Technology(Materials Science)》 SCIE EI CAS 2007年第2期341-345,共5页
Combining with the technology of self-compacting concrete, self-stressing concrete and concrete-filled steel tube, we can get self-compacting and self-stressing concrete-filled steel tube. In order to study the expans... Combining with the technology of self-compacting concrete, self-stressing concrete and concrete-filled steel tube, we can get self-compacting and self-stressing concrete-filled steel tube. In order to study the expansive mechanism of self-stressing concrete, the continuous observation of 47 days on six specimens was carried on. The specimens have different steel area to concrete area ratio. The expansive process in hoop and axial direction were studied, and the expansive mechanism was discussed too. The experimental results identify that the creep and elastic deformation take a large proportion in effective free expansion. The calculating formulas of self-stress in hoop and axial directions were presented here. 展开更多
关键词 self-compacting concrete self-stressing concrete concrete-filled steel tube restrained ex- pansion free expansion CREEP
下载PDF
相变对TiNi合金薄壁管中波速的影响
13
作者 崔世堂 赵红宇 +1 位作者 董方栋 张永亮 《爆炸与冲击》 EI CAS CSCD 北大核心 2024年第9期89-97,共9页
形状记忆合金在受到强冲击荷载作用时会发生相变,而相变对其结构件的动态力学响应影响显著。本文采用同时考虑静水压力和偏应力影响的相变临界准则,推导了增量型的相变本构模型。基于广义特征理论,得到了复杂应力状态下特征波速的解析... 形状记忆合金在受到强冲击荷载作用时会发生相变,而相变对其结构件的动态力学响应影响显著。本文采用同时考虑静水压力和偏应力影响的相变临界准则,推导了增量型的相变本构模型。基于广义特征理论,得到了复杂应力状态下特征波速的解析表达式。特征波速不仅和材料本身的力学参数(如拉压不对称性和混合相的模量)有关,还和材料所处的应力状态有关。对因相变导致体积膨胀的TiNi合金而言,拉压不对称性系数的增大会提高慢波的波速,而对快波几乎没有影响。在相变椭圆的短轴处(α=90°),慢波的波速最低,并随混合相无量纲模量的增大而显著减低,混合相无量纲模量由2增加至5时,波速降低幅度为36.2%,而快波的波速达到最大值c_(0),和混合相的模量无关;在相变椭圆的长轴处(α=180°),慢波的速度达到最大值,而快波的波速达到最小值c_(2)。 展开更多
关键词 相变 复合应力波 薄壁管 TINI合金 伪弹性
下载PDF
海上移动平台直升机甲板圆管支撑结构安全评估
14
作者 王庆丰 洪旺 +1 位作者 诸俊楷 柏健 《江苏科技大学学报(自然科学版)》 CAS 2024年第1期7-12,共6页
圆管支撑结构是海上移动式平台直升机甲板设计的重要部分,由于海上恶劣的风浪环境,使结构整体受风载荷的影响较大.现有直升机甲板圆管支撑结构的安全评估内容主要集中于圆管的静强度分析,缺乏风振响应分析,文中以海洋石油163平台直升机... 圆管支撑结构是海上移动式平台直升机甲板设计的重要部分,由于海上恶劣的风浪环境,使结构整体受风载荷的影响较大.现有直升机甲板圆管支撑结构的安全评估内容主要集中于圆管的静强度分析,缺乏风振响应分析,文中以海洋石油163平台直升机甲板为例,研究圆管支撑结构的静力和动力载荷输入,通过有限元强度分析和理论经验公式计算对比静力、风载荷作用下直升机甲板圆管支撑结构的受力情况,考虑风振涡激效应的准静态分析,在此基础上提出了直升机甲板圆管支撑结构的安全评估方法,探究了风载荷对结构整体安全的影响. 展开更多
关键词 圆管支撑结构 风载荷 应力分析 强度评估 涡激振动
下载PDF
配筋空心圆钢管高强混凝土轴压短柱工作机理分析
15
作者 杨志坚 刘雪 李帼昌 《沈阳建筑大学学报(自然科学版)》 CAS 北大核心 2024年第5期807-817,共11页
目的 提出一种配筋空心圆钢管高强混凝土新型组合柱,分析其在轴向荷载作用下的工作机理,以解决空心钢管混凝土柱空心率较大和延性差等问题。方法 对配筋空心圆钢管高强混凝土短柱进行轴压试验,利用ABAQUS有限元分析软件建立组合柱的有... 目的 提出一种配筋空心圆钢管高强混凝土新型组合柱,分析其在轴向荷载作用下的工作机理,以解决空心钢管混凝土柱空心率较大和延性差等问题。方法 对配筋空心圆钢管高强混凝土短柱进行轴压试验,利用ABAQUS有限元分析软件建立组合柱的有限元模型,以试验结果验证有限元模型的准确性。对组合柱的受力工作机理进行分析,重点研究其在轴向荷载作用下的受力过程、各组分分担内力比例和应力状态。结果 与空心圆钢管高强混凝土柱相比,未配置普通钢筋的试件峰值承载力提升了6.37%、DI提高了6.64%、SI提高了3.59%,配置普通钢筋的试件峰值承载力提升了13.31%、DI提高了8.12%、SI提高了5.68%。整个受力过程中,管柱混凝土和夹层混凝土承载的内力比例分别为36.2%~39.7%和29.0%~30.6%。结论 配置普通钢筋的试件具有更高的承载能力和延性能力;夹层混凝土和管柱混凝土在加载过程中为主要受力组分;钢筋在加载前期基本不承担内力,进入塑性强化阶段才开始发挥作用。 展开更多
关键词 配筋空心钢管混凝土 轴压试验 延性系数 Mises应力
下载PDF
CT70低合金高强度油管用钢激光焊接接头残余应力有限元模拟
16
作者 张阿昱 王建 +2 位作者 张亚刚 毕宗岳 余晗 《焊管》 2024年第6期28-33,共6页
针对CT70级连续管用钢激光焊焊接接头,考虑试板、焊缝、热源的轴对称性,应用有限元软件建立了1/2轴对称有限元分析模型,对激光焊接接头的温度场、变形场与应力场进行了模拟分析。结果表明,有限元模拟焊缝尺寸与实际基本一致;残余应力主... 针对CT70级连续管用钢激光焊焊接接头,考虑试板、焊缝、热源的轴对称性,应用有限元软件建立了1/2轴对称有限元分析模型,对激光焊接接头的温度场、变形场与应力场进行了模拟分析。结果表明,有限元模拟焊缝尺寸与实际基本一致;残余应力主要集中在焊缝周围,在远离焊缝区域残余应力逐渐减小,且焊缝中心为拉应力;变形在焊缝周围最大,距离焊缝越远变形越小。将有限元模拟结果与实际测试结果对比,激光焊焊缝中心为拉应力,与有限元计算结果相同。 展开更多
关键词 低合金高强度油管 激光焊 焊接接头 残余应力
下载PDF
Advanced glycation end products induce neural tube defects through elevating oxidative stress in mice 被引量:6
17
作者 Ru-Lin Li Wei-Wei Zhao Bing-Yan Gao 《Neural Regeneration Research》 SCIE CAS CSCD 2018年第8期1368-1374,共7页
Our previous study showed an association between advanced glycation end products (AGEs) and neural tube defects (NTDs). To understand the molecular mechanisms underlying the effect of AGEs on neural tube developme... Our previous study showed an association between advanced glycation end products (AGEs) and neural tube defects (NTDs). To understand the molecular mechanisms underlying the effect of AGEs on neural tube development, C57BL/6 female mice were fed for 4 weeks with com- mercial food containing 3% advanced glycation end product bovine serum albumin (AGE-BSA) or 3% bovine serum albumin (BSA) as a control. After mating mice, oxidative stress markers including malondialdehyde and H202 were measured at embryonic day 7.5 (E7.5) of ges- tation, and the level of intracellular reactive oxygen species (ROS) in embryonic cells was determined at E8.5. In addition to evaluating NTDs, an enzyme-linked immunosorbent assay was used to determine the effect of embryonic protein administration on the N-(carboxymethyl) lysine reactivity of acid and carboxyethyl lysine antibodies at E10.5. The results showed a remarkable increase in the incidence of NTDs at El0.5 in embryos of mice fed with AGE-BSA (no hyperglycemia) compared with control mice. Moreover, embryonic protein administration resulted in a noticeable increase in the reactivity of N-(carboxymethyl) lysine and N(ε)-(carboxyethyl) lysine antibodies. Malondialdehyde and H2O2 levels in embryonic cells were increased at E7.5, followed by increased intracellular ROS levels at E8.5. Vitamin E supplementation could partially recover these phenomena. Collectively, these results suggest that AGE-BSA could induce NTDs in the absence of hyperglycemia by an underlying mechanism that is at least partially associated with its capacity to increase embryonic oxidative stress levels. 展开更多
关键词 nerve regeneration neural tube defects advanced glycation end products diabetic embryopathy oxidative stress N-(carboxymethyl)lysine malondiadehyde N(ε)-(carboxyethyl) lysine EMBRYO H2O2 bovine serum albumin neural regeneration
下载PDF
水稻花粉管生长及其对非生物逆境胁迫的响应机理研究进展
18
作者 许用强 徐军 +4 位作者 奉保华 肖晶晶 王丹英 曾宇翔 符冠富 《中国水稻科学》 CAS CSCD 北大核心 2024年第5期495-506,共12页
水稻是我国乃至全世界最为重要的粮食作物之一。全球气候变暖背景下,高温、干旱、低温寡照等极端天气频繁发生,水稻产量品质形成受到不同程度的影响,严重威胁我国的粮食安全。花粉管在雌蕊组织中的生长是水稻生殖生长最为关键的过程,高... 水稻是我国乃至全世界最为重要的粮食作物之一。全球气候变暖背景下,高温、干旱、低温寡照等极端天气频繁发生,水稻产量品质形成受到不同程度的影响,严重威胁我国的粮食安全。花粉管在雌蕊组织中的生长是水稻生殖生长最为关键的过程,高温等非生物逆境胁迫可严重干扰花粉管生长的信号传递和能量代谢,进而导致水稻受孕失败。因此,研究高温等逆境胁迫影响水稻花粉管生长及其调控机制具有重要意义。本文综述了水稻花粉管生长的基本过程,包括信号传递以及能量代谢,同时阐述了高温、干旱、低温寡照、重金属等逆境影响花粉管生长致使小穗败育的作用机制及其栽培调控技术,为减缓高温等逆境胁迫干扰水稻花粉管生长,提高水稻授粉受孕能力的栽培技术提供理论参考,并对今后的研究方向进行展望。 展开更多
关键词 水稻 逆境胁迫 花粉管生长 响应机理 调控措施
下载PDF
随动辊压型低应力精密断料教学实验平台开发
19
作者 张立军 杨博涵 +6 位作者 徐嘉怡 张强 赵青 杨宁 傅术林 陶继绍 纪仁杰 《实验技术与管理》 CAS 北大核心 2024年第2期200-207,共8页
为了增强学生对先进成形装备及低应力精密断料技术的理解,开发了随动辊压型低应力精密断料教学实验平台。该实验平台综合利用机械设计、传感器技术及计算机控制技术,将应力集中效应和随动辊压技术引入管料的精密分离断料工序中,设计了... 为了增强学生对先进成形装备及低应力精密断料技术的理解,开发了随动辊压型低应力精密断料教学实验平台。该实验平台综合利用机械设计、传感器技术及计算机控制技术,将应力集中效应和随动辊压技术引入管料的精密分离断料工序中,设计了管料断面质量评价方法,对带有V型槽的45#钢及304不锈钢管料进行了裂纹可控式低应力精密下料实验,验证了断料效果。该实验平台不仅使低应力断料过程更加直观,还提升了学生对低应力精密成形技术的认识,增强了学生对“机械制造工程基础”“切削原理与刀具”及“先进制造技术”等课程的学习兴趣。 展开更多
关键词 低应力断料技术 随动辊压 管料断面 教学实验平台
下载PDF
有载分接开关真空管操动机构力学特性动态仿真
20
作者 顾传宇 严英杰 +3 位作者 刘亚东 邓军 朱强 江秀臣 《上海理工大学学报》 CAS CSCD 北大核心 2024年第5期475-483,共9页
真空管操动机构是换流变有载分接开关的核心部件,其机械结构较为复杂,且因其频繁操作常导致机械机构发生塑性形变与损伤,从而发生换流变故障。研究有载分接开关真空管操动机构力学特性动态仿真能够弥补传统测试手段无法直观展示应力分... 真空管操动机构是换流变有载分接开关的核心部件,其机械结构较为复杂,且因其频繁操作常导致机械机构发生塑性形变与损伤,从而发生换流变故障。研究有载分接开关真空管操动机构力学特性动态仿真能够弥补传统测试手段无法直观展示应力分布的不足,并为真空管操动机构的设计与改进提供理论基础。首先,在ANSYS中建立了基于隐式非线性动力学的真空管操动机构瞬态动力学仿真模型,采用Von Mises屈服准则与等向硬化模型计算模型等效应力;其次通过有限元分析了操动机构整体的应力分布情况;最后针对性地分析了凸转盘、凸杆、支撑机构和真空管的应力分布情况,从而便于深入分析分接开关在各种工况下的工作原理,并有助于根据应力分布情况有效改进操动机构机械结构,并在设计阶段预见并避免可能的故障模式。 展开更多
关键词 真空管操动机构 应力 有限元分析 瞬态动力学
下载PDF
上一页 1 2 89 下一页 到第
使用帮助 返回顶部