Electrical properties and structural optimization of GaN/InGaN/GaN tunnel junctions grown by molecular beam epitaxy

The InGaN films and GaN/InGaN/GaN tunnel junctions(TJs)were grown on GaN templates with plasma-assisted molecular beam epitaxy.As the In content increases,the quality of InGaN films grown on GaN templates decreases and the surface roughness of the samples increases.V-pits and trench defects were not found in the AFM images.p++-GaN/InGaN/n++-GaN TJs were investigated for various In content,InGaN thicknesses and doping concentration in the InGaN insert layer.The InGaN insert layer can promote good interband tunneling in GaN/InGaN/GaN TJ and significantly reduce operating voltage when doping is sufficiently high.The current density increases with increasing In content for the 3 nm InGaN insert layer,which is achieved by reducing the depletion zone width and the height of the potential barrier.At a forward current density of 500 A/cm^(2),the measured voltage was 4.31 V and the differential resistance was measured to be 3.75×10^(−3)Ω·cm^(2)for the device with a 3 nm p++-In_(0.35)Ga_(0.65)N insert layer.When the thickness of the In_(0.35)Ga_(0.65)N layer is closer to the“balanced”thickness,the TJ current density is higher.If the thickness is too high or too low,the width of the depletion zone will increase and the current density will decrease.The undoped InGaN layer has a better performance than n-type doping in the TJ.Polarization-engineered tunnel junctions can enhance the functionality and performance of electronic and optoelectronic devices.

Effect of the mixing of s-wave and chiral p-wave pairings on electrical shot noise properties of normal metal/superconductor tunnel junctions

We study theoretically the electrical shot noise properties of tunnel junctions between a normal metal and a superconductor with the mixture of singlet s-wave and chiral triplet p-wave pairing due to broken inversion symmetry. We investigate how the shot noise properties vary as the relative amplitude between the two parity components in the pairing potential is changed. It is demonstrated that some characteristics of the electrical shot noise properties of such tunnel junctions may depend sensitively on the relative amplitude between the two parity components in the pairing potential, and some significant changes may occur in the electrical shot noise properties when the relative amplitude between the two parity components is varied from the singlet s-wave pairing dominated regime to the chiral triplet p-wave pairing dominated regime. In the chiral triplet p-wave pairing dominated regime, the ratio of noise power to electric current is close to 2e both in the in-gap and in the out-gap region. In the singlet s-wave pairing dominated regime, the value of this ratio is close to 4e in the inner gap region but may reduce to about 2e in the outer gap region as the relative amplitude of the chiral triplet pairing component is increased. The variations of the differential shot noise with the bias voltage also exhibit some significantly different features in different regimes. Such different features can serve as useful diagnostic tools for the determination of the relative magnitude of the two parity components in the pairing potential.

Terahertz high-sensitivity SIS mixer based on Nb–AlN–NbN hybrid superconducting tunnel junctions

The terahertz band,a unique segment of the electromagnetic spectrum,is crucial for observing the cold,dark universe and plays a pivotal role in cutting-edge scientific research,including the study of cosmic environments that support life and imaging black holes.High-sensitivity superconductor–insulator–superconductor(SIS)mixers are essential detectors for terahertz astronomical telescopes and interferometric arrays.Compared to the commonly used classical Nb/AlO_(x)/Nb superconducting tunnel junction,the Nb/AlN/NbN hybrid superconducting tunnel junction has a higher energy gap voltage and can achieve a higher critical current density.This makes it particularly promising for the development of ultra-wideband,high-sensitivity coherent detectors or mixers in various scientific research fields.In this paper,we present a superconducting SIS mixer based on Nb/AlN/NbN parallel-connected twin junctions(PCTJ),which has a bandwidth extending up to490 GHz–720 GHz.The best achieved double-sideband(DSB)noise temperature(sensitivity)is below three times the quantum noise level.

Low frequency noise in asymmetric double barrier magnetic tunnel junctions with a top thin MgO layer

Low frequency noise has been investigated at room temperature for asymmetric double barrier magnetic tunnel junctions（DBMTJs）, where the coupling between the top and middle CoFeB layers is antiferromagnetic with a 0.8-nm thin top Mg O barrier of the CoFeB/MgO/CoFe/CoFeB/MgO/CoFe B DBMTJ. At enough large bias, 1/f noise dominates the voltage noise power spectra in the low frequency region, and is conventionally characterized by the Hooge parameter αmag.With increasing external field, the top and bottom ferromagnetic layers are aligned by the field, and then the middle free layer rotates from antiparallel state（antiferromagnetic coupling between top and middle ferromagnetic layers） to parallel state. In this rotation process αmag and magnetoresistance-sensitivity-product show a linear dependence, consistent with the fluctuation dissipation relation. With the magnetic field applied at different angles（θ） to the easy axis of the free layer,the linear dependence persists while the intercept of the linear fit satisfies a cos（θ） dependence, similar to that for the magnetoresistance, suggesting intrinsic relation between magnetic losses and magnetoresistance.

A Novel Design and Fabrication of Magnetic Random Access Memory Based on Nano-ring-type Magnetic Tunnel Junctions

Nano-ring-type magnetic tunnel junctions （NR-MTJs） with the layer structure of Ta（5）/Ir22Mn78（10）/ Co75Fe25（2）/Ru（0.75）/CoooFe20B20（3）/Al（0.6）-oxide/Co60Fe20B20（2.5）/Ta（3）/Ru（5） （thickness unit： nm） were nano-fabricated on the Si（100）/SiO2 substrate using magnetron sputtering deposition combined with the optical lithography, electron beam lithography （EBL） and Ar ion-beam etching techniques. The smaller NR-MTJs with the inner- and outer-diameter of around 50 and 100 nm and also their corresponding NR-MTJ arrays were nano-patterned. The tunnelling magnetoresistance （TMR ＆ R） versus driving current （I） loops for a spin-polarized current switching were measured, and the TMR ratio of around 35% at room temperature were observed. The critical values of switching current for the free Co60Fe20B20 layer relative to the reference Co6oFe2oB2o layer between parallel and anti-parallel magnetization states were between 0.50 and 0.75 mA in such NR-MTJs. It is suggested that the applicable MRAM fabrication with the density and capacity higher than 256 Mbit/inch2 even 6 Gbite/inch2 are possible using both I NR-MTJ＋1 transistor structure and current switching mechanism based on based on our fabricated 4×4 MRAM demo devices.

Characteristics of Nb/Al superconducting tunnel junctions fabricated using ozone gas

To improve the energy resolution（？E） of Nb/Al superconducting tunnel junctions（STJs）, an ozone（O3） oxidation process has been developed to fabricate a thin defect-free tunnel barrier that simultaneously shows high critical current JC〉 1000 A/cm^2 and high normalized dynamic resistance RDA 〉 100 MΩ·μm^2, where A is the size of the STJ. The 50-μm^2 STJs produced by O3 exposure of 0.26 Pa·min with an indirect spray of O3 gas, which is a much lower level of exposure than the O2 exposure used in a conventional O2 oxidation process, exhibit a maximum JC= 800 A/cm^2 and a high RDA = 372 MΩ ·μm^2. The 100-pixel array of the 100-μm^2STJs produced using the same O3 oxidation conditions exhibits a constant leak current I leak= 14.9 ± 3.2 n A at a bias point around △ /e（where e is half the energy gap of an STJ）,and a high fabrication yield of 87%. Although the I leak values are slightly larger than those of STJs produced using the conventional O2 oxidation process, the STJ produced using O3 oxidation shows a ？E = 10 eV for the C-Kα line, which is the best value of our Nb/Al STJ x-ray detectors.

A Self-consistent Calculation and an Anisotropic Wavelength Cut off Energy of Spin-wave Spectrumin Magnetic Tunnel Junctions

Temperature dependence of tunnel magnetoresistance (TMR) ratio, resistance, and coercivity from 4.2 K to room temperature (RT), applied de bias voltage dependence of the TMR ratio and resistances at 4.2 K and RT, tunnel current I and dynamic conductance dI/dV as functions of the de bias voltage at 4.2 K, and inelastic electron tunneling (IET) spectroscopy, d(2)I/dV(2) versus V, at 4.2 K for a tunnel junction of Ta(5 nm)/Ni79Fe21(25 nm)/Ir22Mn78(12 nm)/Co75Fe25(4 nm)/Al(0.8 nm)-oxide/Co75Fe25(4 nm)/Ni79Fe21(25 nm)/Ta(5 nm) were systematically investigated. High TMR ratio of 59.2% at 4.2 K and 41.3% at RT were observed for this junction after annealing at 275 degreesC for an hour. The temperature dependence of TMR ratio and resistances from 4.2 to 300 K at 1.0 mV bias and the de bias voltage dependence of TMR ratio at 4.2 K from 0 to 80 mV can be evaluated by a comparison of self-consistent calculations with the experimental data based on the magnon-assisted inelastic excitation model and theory. An anisotropic wavelength cutoff energy of spin-wave spectrum in magnetic tunnel junctions (MTJs) was suggested, which is necessary for self-consistent calculations, based on a series of IET spectra observed in the MTJs.

Effects of Fe-Oxide and Mg Layer Insertion on Tunneling Magnetoresistance Properties of CoFeB/MgO/CoFeB Magnetic Tunnel Junctions

To study the influence of CoFeB/MgO interface on tunneling magnetoresistance （TMR）, different structures of magnetic tunnel junctions （MTJs） are successfully prepared by the magnetron sputtering technique and characterized by atomic force microscopy, a physical property measurement system, x-ray photoelectron spectroscopy, and transmission electron microscopy. The experimental results show that TMR of the CoFeB/Mg/MgO/CoFeB structure is evidently improved in comparison with the CoFeB/MgO/CoFeB structure because the inserted Mg layer prevents Fe-oxide formation at the CoFeB/MgO interface, which occurs in CoFeB/MgO/CoFeB MTJs. The inherent properties of the CoFeB/MgO/CoFeB, CoFeB/Fe-oxide/MgO/CoFeB and CoFeB/Mg/MgO/CoFeB MTJs are simulated by using the theories of density functions and non-equilibrium Green functions. The simulated results demonstrate that TMR of CoFeB/Fe-oxide/MgO/CoFeB MTJs is severely decreased and is only half the value of the CoFeB/Mg/MgO/CoFeB MTJs. Based on the experimental results and theoretical analysis, it is believed that in CoFeB/MgO/CoFeB MTJs, the interface oxidation of the CoFeB layer is the main reason to cause a remarkable reduction of TMR, and the inserted Mg layer may play an important role in protecting Fe atoms from oxidation, and then increasing TMR.

Thermally activated magnetization reversal in magnetic tunnel junctions

In this paper, the magnetization reversal of the ferromagnetic layers in the IrMn/CoFe/AlOx/CoFe magnetic tunnel junction has been investigated using bulk magnetometry. The films exhibit very complex magnetization processes and reversal mechanism. Thermal activation phenomena such as the training effect, the asymmetry of reversal, the loop broadening and the decrease of exchange field while holding the film at negative saturation have been observed on the hysteresis loops of the pinned ferromagnetic layer while not on those of the free ferromagnetic layer. The thermal activation phenomena observed can be explained by the model of two energy barrier distributions with different time constants.

Tantalum oxide barrier in magnetic tunnel junctions

Tantalum as an insulating barrier can take the place of Al in magnetic tunnel junctions (MTJs). Ta barriers in MTJs were fabricated by natural oxidation. X-ray photoelectron spectroscopy (XPS) was used to characterize the oxidation states of Ta barrier. The experimental results show that the chemical state of tantalum is pure Ta^(5+) and the thickness of the oxide is 1.3 nm. The unoxidized Ta in the barrier may chemically reacted with NiFe layer which is usually used in MTJs to form an intermetallic compound, NiTa_2. A magnetic 'dead layer' could be produced in the NiFe/Ta interface. The 'dead layer' is likely to influence the spinning electron transport and the magnetoresistance effect.

Spin-Polarization in Quasi-Magnetic Tunnel Junctions

Spin polarization in ferromagnetic metal/insulator/spin-filter barrier/nonmagnetic metal, referred to as quasimagnetic tunnel junctions, is studied within the free-electron model. Our results show that large positive or negative spin-polarization can be obtained at high bias in quasi-magnetic tunnel junctions, and within large bias variation regions, the degree of spin-polarization can be linearly tuned by bias. These linear variation regions of spin-polarization with bias are influenced by the barrier thicknesses, barrier heights and molecular fields in the spin-filter （SF） layer. Among them, the variations of thickness and heights of the insulating and SF barrier layers have influence on the value of spin-polarization and the linear variation regions of spin-polarization with bias. However, the variations of molecular field in the SF layer only have influence on the values of the spin-polarization and the influences on the linear variation regions of spin-polarization with bias are slight.

Tantalum oxide barrier in magnetic tunnel junctions

Tantalum as an insulating barrier can take the place of Al in magnetic tunneljunctions (MTJs). Ta barriers in MTJs were fabricated by natural oxidation. X-ray photoelectronspectroscopy (XPS) was used to characterize the oxidation states of Ta barrier. The experimentalresults show that the chemical state of tantalum is pure Ta^(5+) and the thickness of the oxide is1.3 nm. The unoxidized Ta in the barrier may chemically reacted with NiFe layer which is usuallyused in MTJs to form an intermetallic compound, NiTa_2. A magnetic 'dead layer' could be produced inthe NiFe/Ta interface. The 'dead layer' is likely to influence the spinning electron transport andthe magnetoresistance effect.

The p recombination layer in tunnel junctions for micromorph tandem solar cells

A new tunnel recombination junction is fabricated for n-i-p type micromorph tandem solar cells. We insert a thin heavily doped hydrogenated amorphous silicon （a-Si：H） p^＋ recombination layer between the n a-Si：H and the p hydrogenated nanocrystalline silicon （nc-Si：H） layers to improve the performance of the n-i-p tandem solar cells. The effects of the boron doping gas ratio and the deposition time of the p-a-Si：H recombination layer on the tunnel recombination junctions have been investigated. The current-voltage characteristic of the tunnel recombination junction shows a nearly ohmic characteristic, and the resistance of the tunnel recombination junction can be as low as 1.5 Ω-cm^2 by using the optimized p-a-Si：H recombination layer. We obtain tandem solar cells with open circuit voltage Voc = 1.4 V, which is nearly the sum of the Vocs of the two corresponding single cells, indicating no Voc losses at the tunnel recombination junction.

Influence of interface within the composite barrier on the tunneling electroresistance of ferroelectric tunnel junctions with symmetric electrodes

The interface with a pinned dipole within the composite barrier in a ferroelectric tunnel junction（FTJ） with symmetric electrodes is investigated.Different from the detrimental effect of the interface between the electrode and barrier in previous studies,the existence of an interface between the dielectric SrTiO_3 slab and ferroelectric BaTiO_3 slab in FTJs will enhance the tunneling electroresistance（TER） effect.Specifically,the interface with a lower dielectric constant and larger polarization pointing to the ferroelectric slab favors the increase of TER ratio.Therefore,interface control of high performance FTJ can be achieved.

An Explicit Function Expression for dc Bias and Temperature Dependence of Magnetoresistances in Magnetic Tunnel Junctions

An explicit function expression for the bias voltage or/and temperature dependences of tunnel magnetoresistance ratio and resistances were obtained with a unique set of intrinsic parameters. Two of these intrinsic parameters are the Curie temperature TC and the density of state (DOS) for itinerant majority and minority electrons ξ(ρM/ρm), which are the eigen parameters of ferromagnetic electrodes. Others are the spin-dependent matrix-element ratio (i.e., |Td|2/|TJ|2 ) and the anisotropic-wavelength-cutoff energy ECγ of spin-wave spectrum in magnetic tunnel junction (MTJ), which are the structure parameters of an MTJ. These intrinsic parameters can be predetermined using the experimental measurement or, in principle, using the first-principle calculation method for an MTJ with the three key layers of FM/I/FM. Furthermore, a series of experimental data for an MTJ, for example, a spin-valve-type MTJ of Ta (5 nm)/Ni79Fe21(25 nm)/lr22Mn78(12 nm)/Co75Fe25(4 nm)/AI(0.8 nm)-oxide/Co75Fe25(4 nm)/Ni79Fe21(20 nm)/Ta (5 nm) in this work, can be self-consistently evaluated and explained using such concise explicit function formulations.

GaInP/GaAs tandem solar cells with highly Te- and Mg-doped GaAs tunnel junctions grown by MBE

We report a GaInP/GaAs tandem solar cell with a novel GaAs tunnel junction（TJ） with using tellurium（Te） and magnesium（Mg） as n- and p-type dopants via dual-filament low temperature effusion cells grown by molecular beam epitaxy（MBE） at low temperature. The test Te/Mg-doped GaAs TJ shows a peak current density of 21 A/cm2. The tandem solar cell by the Te/Mg TJ shows a short-circuit current density of 12 m A/cm2, but a low open-circuit voltage range of1.4 V^1.71 V under AM1.5 illumination. The secondary ion mass spectroscopy（SIMS） analysis reveals that the Te doping is unexpectedly high and its doping profile extends to the Mg doping region, thus possibly resulting in a less abrupt junction with no tunneling carriers effectively. Furthermore, the tunneling interface shifts from the intended Ga As n＋＋/p＋＋junction to the AlGaInP/GaAs junction with a higher bandgap AlGaInP tunneling layers, thereby reducing the tunneling peak. The Te concentration of ~ 2.5 × 1020 in GaAs could cause a lattice strain of 10-3 in magnitude and thus a surface roughening,which also negatively influences the subsequent growth of the top subcell and the GaAs contacting layers. The doping features of Te and Mg are discussed to understand the photovoltaic response of the studied tandem cell.

Impurity-limited quantum transport variability in magnetic tunnel junctions

We report an extensive first-principles investigation of impurity-induced device-to-device variability of spin-polarized quantum tunneling through Fe/MgO/Fe magnetic tunnel junctions （MTJ）. In particular, we calculated the tunnel magnetoresistance ratio （TMR） and the average values and variances of the currents and spin transfer torque （STT） of an interfacially doped Fe/MgO/Fe MTJ. Further, we predicted that N-doped MgO can improve the performance of a doped Fe/MgO/Fe MTJ. Our first- principles calculations of the fluctuations of the on/off currents and STT provide vital information for future predictions of the long-term reliability of production. spintronic devices, which is imperative for high-volume

A Hybrid Random Number Generator Using Single Electron Tunneling Junctions and MOS Transistors

This paper proposes a novel single electron random number generator （RNG）. The generator consists of multiple tunneling junctions （MTJ） and a hybrid single electron transistor （SET）/MOS output circuit. It is an oscillator-based RNG. MTJ is used to implement a high-frequency oscillator, which uses the inherent physical randomness in tunneling events of the MTJ to achieve large frequency drift. The hybrid SET and MOS output circuit is used to amplify and buffer the output signal of the MTJ oscillator. The RNG circuit generates high-quality random digital sequences with a simple structure. The operation speed of this circuit is as high as 1GHz. The circuit also has good driven capability and low power dissipation. This novel random number generator is a promising device for future cryptographic systems and communication applications.

Observation of magnetic droplets in magnetic tunnel junctions

Magnetic droplets,a class of highly nonlinear magnetodynamic solitons,can be nucleated and stabilized in nanocontact spintorque nano-oscillators.Here we experimentally demonstrate magnetic droplets in magnetic tunnel junctions(MTJs).The droplet nucleation is accompanied by power enhancement compared with its ferromagnetic resonance modes.The nucleation and stabilization of droplets are ascribed to the double-Co Fe B free-layer structure in the all-perpendicular MTJ,which provides a low Zhang-Li torque and a high pinning field.Our results enable better electrical sensitivity in fundamental studies of droplets and show that the droplets can be utilized in MTJ-based applications and materials science.

Influence of oxygen content on the crystallinity of MgO layers in magnetic tunnel junctions

With RF sputtering process, Si/Si02/Ta/Ru/Ta/CoFeB/MgO/CoFeB/Ta/Ru structure has been grown on Si （100） substrate. Attempting different targets and adjusting the oxygen dose, the crystallization quality of the MgO layer is studied. The X-ray diffraction measurements demonstrate that crystal structure and crystallization quality of MgO layers are related to the type of target and concentration of oxygen in sputtering process. With the method sputtering Mg in an ambient flow of oxygen, not only the crystallization quality of a normal MgO layer with lattice constant of 0.421 nm is improved, but also a new MgO crystal with lattice constant of 0.812 nm is formed and the perpendicular magnetic anisotropy of CoFeB is enhanced. Also it is found that crystallization quality for both the normal MgO and new MgO is more improved with MgO target and same oxygen dose, which means that this new method is helpful to form a new structure of MgO annealed at 400 ℃ in vacuum. with lattice constant of 0.812 nm. All of the samples were