During strip casting,the thickness deviation of casting strip directly affects the quality of the hot-rolled sheet because the casting strip needs to be rolled only once.To accurately control the gap between casting r...During strip casting,the thickness deviation of casting strip directly affects the quality of the hot-rolled sheet because the casting strip needs to be rolled only once.To accurately control the gap between casting rolls and reduce the thickness deviation of the casting strip,a conceptual design of a prestressed twin-roll caster is proposed herein;this caster involves the setting of a constant pressure balancing cylinder between the chocks of two casting rolls.The balancing cylinder hydraulic system adopts a three-way servo valve that controls the hydraulic cylinder.The parameters of the hydraulic power components are determined using the principle of optimal power matching,and the hydraulic system model of the balancing cylinder is thus established.The dynamic analysis and simulation of the hydraulic system are performed using finite element model to obtain relevant evaluation indexes.Finally,the hydraulic system is corrected using proportional-integral-derivative (PID) correction to achieve a well-controlled effect.Thus,the engineering requirements of the strip casting process can be met.展开更多
The twin roll caster for aluminum alloys has many a dv antages. For example, rapid solidification, low equipment cost, and low running cost, etc. However, the twin roll caster has some disadvantages. They are slow c a...The twin roll caster for aluminum alloys has many a dv antages. For example, rapid solidification, low equipment cost, and low running cost, etc. However, the twin roll caster has some disadvantages. They are slow c asting speed and limitation of alloys. In the conventional twin roll caster, the casting speed is slower than 10 m/min. Aluminum alloys, which freezing range is wide, can not be cast. In the present study, break through of these problems wa s tried, and a new type twin roll caster was devised. A vertical type twin roll caster equipped with a nozzle was devised in order to cast aluminum strips at the speeds higher than 60 m/min. Characteristic features of this caster were vertical type, use of copper rolls, low separating force (n o operation of rolling), no use of lubricant, and equipment of the nozzle. In th e high speed roll casting, feed of molten metal of the vertical type twin roll c aster was easier than that of the conventional horizontal type caster. The use o f the copper rolls made cooling rate higher. The low separating force and the us e of the copper rolls prevented sticking of the strip to the roll. The lubricant was not needed, as the sticking of the strip to the roll did not occur. No use of the lubricant was useful to increase the cooling rate and casting speed of th e strip. The nozzle was used in order to improve contact condition (heat transfe r) between the melt and the rolls by hydrostatic pressure. In the twin roll cast er of the present study, many devices were done to improve the cooling condition of the strip in order to increase the casting speed. It was said that the roll casting of A5182 was very difficult, as freezing zone of A5182 was very wide. However, A5182 strip could be cast at high speeds up to 120 m/min using the twin roll caster of the present study. The microstructure of the strip cast using the conventional type twin roll caster is columnar structu re. The microstructure of the strip cast using the twin roll caster of the prese nt study was not columnar but equiaxed structure. It is said that mechanical pro perties of the strip cast using the twin roll caster is cheaper than that of the strip made from DC casting. However, the mechanical properties of the strip cas t using the twin roll caster in the present study were almost same as the proper ties of the strip made from DC casting. The thickness of the strip cast using th e twin roll caster of the present study was from 1.5 mm to 2.5 mm, and this thic kness was thinner than that of the strip cast using the conventional twin roll c aster. Semisolid roll casting was tried in order to increase the roll speed more and mo re. The twin roll caster of the present study was equipped with a cooling slope in order to make semisolid slurry. The cooling slope was the simplest process to make the semisolid slurry. Solid rate of the semisolid slurry was about 10%. Th e casting speed increased up to 180 m/min by the effect of semisolid casting. Me chanical properties were improved by the semisolid casting, too.展开更多
文摘During strip casting,the thickness deviation of casting strip directly affects the quality of the hot-rolled sheet because the casting strip needs to be rolled only once.To accurately control the gap between casting rolls and reduce the thickness deviation of the casting strip,a conceptual design of a prestressed twin-roll caster is proposed herein;this caster involves the setting of a constant pressure balancing cylinder between the chocks of two casting rolls.The balancing cylinder hydraulic system adopts a three-way servo valve that controls the hydraulic cylinder.The parameters of the hydraulic power components are determined using the principle of optimal power matching,and the hydraulic system model of the balancing cylinder is thus established.The dynamic analysis and simulation of the hydraulic system are performed using finite element model to obtain relevant evaluation indexes.Finally,the hydraulic system is corrected using proportional-integral-derivative (PID) correction to achieve a well-controlled effect.Thus,the engineering requirements of the strip casting process can be met.
文摘The twin roll caster for aluminum alloys has many a dv antages. For example, rapid solidification, low equipment cost, and low running cost, etc. However, the twin roll caster has some disadvantages. They are slow c asting speed and limitation of alloys. In the conventional twin roll caster, the casting speed is slower than 10 m/min. Aluminum alloys, which freezing range is wide, can not be cast. In the present study, break through of these problems wa s tried, and a new type twin roll caster was devised. A vertical type twin roll caster equipped with a nozzle was devised in order to cast aluminum strips at the speeds higher than 60 m/min. Characteristic features of this caster were vertical type, use of copper rolls, low separating force (n o operation of rolling), no use of lubricant, and equipment of the nozzle. In th e high speed roll casting, feed of molten metal of the vertical type twin roll c aster was easier than that of the conventional horizontal type caster. The use o f the copper rolls made cooling rate higher. The low separating force and the us e of the copper rolls prevented sticking of the strip to the roll. The lubricant was not needed, as the sticking of the strip to the roll did not occur. No use of the lubricant was useful to increase the cooling rate and casting speed of th e strip. The nozzle was used in order to improve contact condition (heat transfe r) between the melt and the rolls by hydrostatic pressure. In the twin roll cast er of the present study, many devices were done to improve the cooling condition of the strip in order to increase the casting speed. It was said that the roll casting of A5182 was very difficult, as freezing zone of A5182 was very wide. However, A5182 strip could be cast at high speeds up to 120 m/min using the twin roll caster of the present study. The microstructure of the strip cast using the conventional type twin roll caster is columnar structu re. The microstructure of the strip cast using the twin roll caster of the prese nt study was not columnar but equiaxed structure. It is said that mechanical pro perties of the strip cast using the twin roll caster is cheaper than that of the strip made from DC casting. However, the mechanical properties of the strip cas t using the twin roll caster in the present study were almost same as the proper ties of the strip made from DC casting. The thickness of the strip cast using th e twin roll caster of the present study was from 1.5 mm to 2.5 mm, and this thic kness was thinner than that of the strip cast using the conventional twin roll c aster. Semisolid roll casting was tried in order to increase the roll speed more and mo re. The twin roll caster of the present study was equipped with a cooling slope in order to make semisolid slurry. The cooling slope was the simplest process to make the semisolid slurry. Solid rate of the semisolid slurry was about 10%. Th e casting speed increased up to 180 m/min by the effect of semisolid casting. Me chanical properties were improved by the semisolid casting, too.
