Solidification microstructure of Ti-43Al alloy by twin-roll strip casting

As a near-net-shape technology,the twin-roll strip casting(TRC)process can be considered to apply to the fabrication of TiAl alloy sheets.However,the control of the grain distribution is very important in strip casting because the mechanical properties of strips are directly determined by the solidification microstructure.A three-dimensional(3D)cellular automation finite-element(CAFE)model based on ProCAST software was established to simulate the solidification microstructure of Ti-43Al alloy.Then,the influence of casting temperature and the maximum nucleation density(nmax)on the solidification microstructure was investigated in detail.The simulation results provide a good explanation and prediction for the solidification microstructure in the molten pool before leaving the kissing point.Experimental and simulated microstructure show the common texture<001>orientation in the columnar grains zone.Finally,the microstructure evolution of the Ti-43Al alloy was analyzed and the solidification phase transformation path during the TSC process was determined,i.e.,L→L+β→β→β+α→α+γ+β/B2 phase under a faster cooling rate and L→L+β→β→β+α→γ+lamellar(α_(2)+γ)+β/B2 phase under a slower cooling rate.

Numerical simulation of the temperature fields of stainless steel with different roller parameters during twin-roll strip casting

The temperature field of stainless steel during twin-roll strip casting was simulated by experiment and a finite element （FE） model. By comparing the measured result with the simulated values, it is found that they fit close to each other, which indicates this FE model is effective. Based on this model, the effects of roll gap （t） and roll radius （R） on solidification were simulated. The simulated results give the relationship between t or R and the position of the freezing point. The larger the t is and the smaller the R is, the closer the position of the freezing point is to the exit.

Water Modeling of Twin-Roll Strip Casting

Twin-roll strip casting is regarded as a prospective technology of near net shape continuous casting. The fluid flow field and level fluctuation in the pool have a strong influence not only on composition and temperature homogeneity of pool, but also on the strip quality. A 1 ： 1 water model of a twin-roll strip caster was set up based on the criteria of Froude number and Reynold number similarity. The level fluctuation was measured. The influence of pool depth, casting speed and feeding system configuration on level fluctuation in the pool was studied. The experimental results provided a basis for the optimization of feeding system and process parameters.

Numerical and physical simulation of a twin-roll strip caster

The 1：1 water model of a twin-roll strip caster was set up based on the Froude number and the Reynolds number similarity criteria. A new type metal delivery system was designed for the twin-roll strip caster. The level fluctuation and the fluid flow in the pool of the water model were measured using the level detector and the 3D-LDV （laser Doppler velocimetry） technology. It is shown that a wedged delivery system can produce the desirable level fluctuation and even fluid flow distribution in the pool Numerical simulations for the water model were performed. Comparisons between the numerical and physical simulation results show good agreement near the side dams.

Simulation of Fluid Flow, Heat Transfer and Micro-Segregation in Twin-roll Strip Casting of Stainless Steel

In twin-roll strip casting process, metal flow and temperature distribution in the molten pool directly affect the stability of the process and the quality of products. In this paper, a 3D coupled thermal-flow fenite element modeling （FEM） simulation for twin-roll strip casting of stainless steel was performed. Influences of the pouring temperature and casting speed on the temperature fields were obtained from the numerical simulation. The micro-segregation of the solutes during the strip casting process of stainless steel was also simulated. A developed micro-segregation model was used to calculate the micro-segregation of solutes in twin-roll casting of stainless steel. The relationship between the solidus fraction in solidification and temperature was given, which was used to determine the LIT （liquid impermeable temperature）, ZST （zero strength temperature） and ZDT （zero ductility temperature） in the period of non-equilibrium solidification. The effect of temperature on the micro-segregation was discussed. According to the computational results, the solidification completion temperature in the twin-roll strip casting of stainless steel was then determined, which can provide a basis for controlling the location of solidification completion temperature and analysing the crack of the casting strip.

NUMERICAL SIMULATION OF MOLTEN POOL AND CONTROL STRATEGY OF KISS POINT IN A TWIN-ROLL STRIP CASTING PROCESS

Coupled turbulent flow, temperature fields of the twin-roll casting strip process were simulated by three-dimensional finite element method. Based on the heat balance calculation and using inverse methods between the simulations and real experiments, the relational models among casting speed, location, and coefficient of heat transfer between molten metal and rolls in different regions are given. In the simulation, the calculated surface temperatures are in good agreement with the measured values. An on-line model of kiss point is derived by simulations and the geometry of molten pool, corresponding control strategy is also proposed.

Application of Fuzzy Logic Controller to Level Control of Twin-Roll Strip Casting

An intelligent fuzzy-PID controller consisting of fuzzy logic controller and PID controller was developed to control the molten steel level of twin-roll strip caster.Additionally,a feedforward differential PID controller was used for stopper position control in order to avoid differential kick.It is proved by simulation that the proposed intelligent controller is able to obtain zero steady state error asymptotically and the control system is robust due to its fuggy behavior of the controller.

Heat Transfer Characteristic of Molten Pool for Twin-Roll Strip Casting

Body-fitted coordinate transformation equation was deduced and used to generate the body-fitted grids of molten pool for twin-roll strip casting.The orthogonality of the grids on the boundary was modified by adjusting source item.The energy equation and the boundary conditions were transformed from physical space to computational space.The velocity field model proposed by Hirohiko Takuda was used to calculate the temperature field of molten steel,and the influence of technical factors was also discussed.

Investigation of the solute transportation coupled with heat transfer and fluid flow during twin-roll strip casting process

Mathematical model of solute [C] distribution in twin-roll strip casting process has been setup successfully with Calcosoft for the first time. Simulation result shows that in the center of the molten steel pool between the two rolls there is a vortex flow, which is a solute enriched area. But the highest solute concentration position is at the solidification front of the columnar grain zone near the cooling roll surface. Another solute enriched position is in the back flow above the nip point. Combined with the formation mechanism of microstruoture in final as cast strip, analysis shows that solute enriched area is in the transitional area between columnar and equiaxed grain zone.

Mathematical modeling of fluid flow and level profile during twin-roll strip casting process

In twin-roll strip casting process,transport phenomena of fluid in the molten pool directly affect the process stability and the quality of products.In order to elucidate the fundamental transport phenomena in twin-roll casting,a commercial software called ProCAST was employed to simulate the transient fluid flow and level profile behaviors during the early stage of the process in this study.The coupled set of governing differential equations for mass,momentum and energy balance were solved with the finite element method and the transient free surface problem was treated with a volume of fluids(VOF) approach.The effect of different delivery systems configuration on flow pattern,level profile in the pool was studied and analyzed in this paper. The new wedge metal delivery systems have been optimized for the twin-roll strip caster.It was shown that new type metal delivery systems had a preferable effect on the uniform distribution of fluid and level fluctuation in the pool.The simulation results also provide a valuable basis for the optimization of delivery system and process parameters during the initial pouring stage.

Electromagnetic Dam in Twin-Roll Strip Caster

The electromagnetic dam （EMD） in twin-roll strip caster was simulated with FEM. The results show that the direction and magnitude of Lorentz force distributing in the EMD changed in a period. The negative part is about 30% of the positive part, and the acting time of the negative force is about 40% of a period. In order to prevent the liquid steel from leaking efficiently, the distance between two poles should be the same from the top to the bottom of the EMD, otherwise the magnetic induction will be very small at the top and large at the bottom.

Nonmetallic inclusions in SUS304 strip produced by twin-roll strip casting

The shape, type, content, and dimension of nonmetallic inclusions in SUS304 strip produced by twin-roll strip casting were studied using scanning electron microscopy （SEM）. The results show that the inclusions are mainly spherical Al2O3 and complex oxides composed of MnO, Al2O3 , and SiO2. The percentage of fine oxides smaller than 3 μm reaches up to 51.8%. The theoretical calculations show that fine oxides have precipitated during solidification. Therefore, it is concluded that during twin-roll strip casting, because of high cooling rate, the size of inclusions precipitated during solidification decreases, and the amount increases.

Study of measurement and control of free loop of hot steel strip in twin-roll strip casting

In the twin-roll strip casting process, hot cast strips can be broken or tom if the casting speed does not match the rolling speed. Usually, a certain length of hot steel strip is hung freely between the caster and rolling mill to deal with the effect of this speed difference. In this paper,the freely hanging hot steel strip is referred to as the free loop of hot steel strip. Accurately measuring and controlling the height of this free loop is the key factor in maintaining a stable casting operation. Several methods for measuring the loop height of a steel strip are discussed and a method for accurately measuring and controlling the free loop height of hot steel strip is presented. Based on the results of the casting loop quantity change curve, this control method is confirmed to be effective and able to meet the requirements of continuous casting strip production.

Coupled Simulation of Flow and Thermal Field of Twin-Roll Strip Casting Process

The first micro-segregation under conditions of twin roll strip casting was simulated.The relationship between the temperature and solid fraction in the mushy zone was given.The temperatures such as ZDT,LIT were got from this simulation.Then using the turbulent model,the flow field and thermal field in the pool of twin-roll strip caster was simulated.The speed and temperature at different casting speed was given,and the results were also explained.By these two simulations,the appropriate casting speed can be found.These simulations can provide effective data for controlling the twin-roll strip casting process.

Effect of Oscillation Parameters to Flow Field in the Pool during the Oscillating Twin-Roll Strip Casting Process

During the oscillating twin?roll strip casting process, the quality of final products is directly influenced by the flow field distribution of molten metal in the pool. The variation in the flow field is caused by oscillating roller benefits, for homogeneous distribution of strip impurity, and decreasing the grain size. Thus, the quality of the strip could be improved. A numerical model was developed using the multiphase flow technology, coupled with heat transfer, fluid flow, solidification, and oscillation. Furthermore, a transient algorithm was adopted for simulating the oscillating twin?roll strip casting process of AlSi9Cu3 and 3104 aluminum alloy. This paper focuses on the flow distribution in the pool, in comparison with the traditional vertical twin?roll strip casting process, while the amplitude or frequency is chang?ing with the definite value of casting velocity, roller diameter, nozzle angle, and the strip thickness. Consequently, the conclusions were experimentally validated by oscillating twin?roll 3104 aluminum alloy strip casting. Vibrating casting technology can change the flow field in the pool by vibration, which can improve the quality of the strip core.

Wear analysis of a side dam in twin-roll strip casting

Reducing wear on a side dam can prolong the casting operation life of a twin-roll strip casting process,thus reducing production cost and improving casting stability.To lengthen the service life of the side dam,it is necessary to understand the wear performance of the side dam material.To investigate the wear behavior mechanism of the side dam,in this study,the UMT-2 friction and wear tester was used to determine the relationship between the wear rate of the side-dam material and various parameters.Based on the roughness of the contact area between the side dam and the end of the casting rolls as well as on the amount of deformation of the side dam,which was derived using a thermal-deformation simulation model,the reasons for the uneven wear of the side dam were obtained.

The future of the twin-roll strip casting and rolling process

Twin-roll strip casting and rolling is a typical near-net-shape steel manufacturing process.The twin-roll strip casting and rolling of low-carbon steel strips has made a number of breakthroughs and achieved significant results during the past 20 years.Baosteel has been paying close attention to the development of this technology and set up a research and development project focused on its industrialization in 2001.The Ningbosteel-Baosteel strip casting industrialization demo project(NBS),which was launched in 2016,marks the strip-casting technology(registered as Baostrip) developed by Baosteel as having reached an advanced international level after 15 years of effort.This paper summarizes the results obtained in the industrialized demonstration plant and considers the future development of strip casting and rolling.

Analysis of surface microcracks in low-carbon steel produced via twin-roll strip casting

In this study,morphological and microstructural analyses were conducted on net-shaped microcracks appearing on the surface of low-carbon steel manufactured via twin-roll strip casting. The fractograph and microscale distribution of elements in the cracked region were also analyzed. Results revealed that the cracked surfaces were characterized by slight pits,along with inclusions composed of manganese and silicon oxide distributed along both the sides of the cracks. Fractograph analysis revealed that the crack and smooth dendrite surfaces were oxidized. These phenomena indicate that microcracks on the cast strip surface form at the hightemperature stage of the solidification process during twin-roll casting and rolling. Microcracks were present in each region with pits in the cast strip and extended along the dendrite interface because of the combined effects of phasechange stress,thermal stress,mechanical stress,and fractional crystallization during the solidification process.

Research on directly cold-rolled AISI 304 stainless steel strip with the twin-roll strip casting process

In order to improve the surface quality and properties of AISI 304 stainless steel strip produced with the twinroll strip casting process,the strip was directly cold-rolled. The results show that cold rolling clearly improves the surface roughness,microstructure and properties. Residual δ ferrite is greatly decreased, anisotropy becomes less obvious and corrosion resistance is greatly improved. These results demonstrate the feasibility of directly cold-rolled AISI 304 stainless steel strip.

High temperature mechanical properties of low carbon silicon-bearing steel by twin-roll strip casting

The tensile equipment of the advanced confocal scanning laser microscope （CSLM） was used to research the high temperature mechanical properties of low carbon silicon-bearing steel by twin-roll strip casting. The results show that, at the strain rate of 0. 000 5 s ^-1, the strip clearly shows signs of brittleness at around 600 ℃ and its plasticity falls considerably between 750 ℃ and 600 ℃. This is because during the transformation from austenite to ferrite, the low strength ferrite at the austenite grain boundaries greatly reduces the steel＇ s high temperature plasticity. The subsequent strip coiling process should be controlled at less than the brittle temperature of approximately 600 ℃, so cracks at the coiling stage can be prevented.