Solvent de binding of water soluble binder in powder injection moulding

The solvent debinding of water soluble binder in powder injection moulding (MIM) was investigated systematically, including the effects of solvent types, temperature and the thickness of green parts on the solvent debinding rate. After studying the debinding of a green part with a thickness of 4.26 mm, it was found that, the debinding rate of polyethylene glycol(PEG) in water and alcohol was high initially, and then decreased; however, it would increase with temperature increasing. At room temperature, the dissolution rate of PEG in water was higher than that in alcohol, but the latter would be much faster with temperature increasing because the debinding activation energy in alcohol was 51.44 kJ·mol -1 ·K -1 , much higher than 24.23 kJ·mol -1 ·K -1 in water. With a green part thickness larger than 4.26 mm, the debinding was controlled by diffusion; but with that smaller than 2.36 mm, the debinding was controlled by both dissolution and diffusion.

MATHEMATICAL AND PHYSICAL MODELING OF INTERFACIALPHENOMENA IN CONTINOUS CASTING MOULD WITH ARGONINJECTION THROUGH SUBMERGED ENTRV NOZZLE

The study on the fluid flow, meniscus oscillation, slag entrapment in continuous casting mould was conducted mathematically and experimentally. The results show that the injection of argon into submerged nozzle enhances the meniscus oscillation, thus increases the probability of slag entrapment, and the critical argon blowing flow rate, which will give rise to slag entrapment, is around 10l/min. The trajectory of bubble is affected by the bubble diameter and the molten steel flow, and the bubble diameter is dominant. The bubble with diameter 1.4mm floats fastest with 0.47m/s terminal velocity.

Bi-phasic Simulation of Metal Injection Moulding:Constitutive Determinations

To predict the segregation effect in metal injection moulding (MIM) injection, a bi-phasic model based on mixture theory is adopted in simulation. An explicit algorithm is developed and realized by the authors, which conducts the simulation to be a cost-effective tool in MIM technology. In case of the bi-phasic simulation, the viscosity behaviours are necessary to be determined for the flows of each phase while only the viscosity of mixture is measurable by tests. It is a crucial problem for application of the bi-phasic simulation of MIM injection. A reasonable method is hence analysed and proposed to determine the viscosity behaviours of each phase. Even though this method may be furthermore modified in the future, it results in the practical simulation of segregation effects with reasonable parameters. The simulation results are compared with the measurements on injected specimens.

Study on Injection Moulding of High Precision Aspheric Plastic Lens

With the rapid development of information and multi me dia technologies, the demand for the optical plastic aspheric elements used in o pto-electronic devices, camera, optical disc and projector lens etc. has been i ncreased rapidly in the recent years. The key technologies of fabrication of asp heric plastic lens are the design and manufacturing moulds, selection of proper injection moulding equipment, and optimization of injection moulding parameters etc. In this paper, the effect of injection pressure, moulding temperature, cool ing time and injection speed on the surface profile of the lenses during injecti on and holding process is investigated. Surface quality of plastic lenses is mea sured by Talysurf Texture Measuring System. The experimental results showed that the injection pressure and moulding temperature are important parameters compar ing to cooling time and injection speed. A bit change of injection pressure or m oulding temperature will affect the property of the surface profile. Either incr easing injection pressure or mould temperature can achieve less shrinkage. Other wise, a lower injection pressure will produce more shrinkage, more air traps and a lower mould temperature results greater warp and higher shrinkage. The dynami c process of injection for optical plastic lenses is simulated by 3D Moldflow pl astic Insight software (MPI). The MPI will help us to optimize injection mouldin g parameters.

Permeable Steel and Its Application in Plastic-injection Mould

The gas in plastics mould has great influence on performance, appearance and lifespan of the injection molded parts. Venting channel and its appendix system should be used for gas exhausting in general. However, the dependence on the venting system complicates the mould design. Furthermore in certain condition, it is difficult to integrate the venting system into the mould. Currently a kind of mold material which has gas permeability has been developed in abroad, but the applications of this mold material were restricted by its higher cost and smaller size. In this research, a porous material which was made by powder metallurgy was applied to plastic mould to replace the venting system. Permeability of the steel with different secondary processing was tested and compared with a special apparatus. The metallographic samples of the steel with different secondary processing were prepared and investigated. Finally an actual injection set was established to investigate the applications of permeable steel. The metallographies indicate that the micro-holes inside permeable steel were interconnected. Moulds made of permeable steel exhibit good permeability in the plastic-injection experiments and gas generated in the mould cavity was smoothly exhausted. The melted plastic did not penetrate into the mould or block in the micro-holes. After several times of plastic-injection experiments, the mould still retained good permeability. The strength of this permeable steel is between 200–250 MPa and suitable for industrial applications. The venting systems simplified by permeable steel in plastic-injection have simple structures, which can be applied into any place that requires gas exhausting.

The Comparison Between Finite Element Analysis and Experimental Results of the Cooling of Injection Moulds with Hot Runner System

In an injection moulding process, the mould cooling s ystem is very important as an efficient and uniform cooling effect can improve b oth the productivity and part quality. Due to the complexity of the process, muc h research on the mould cooling analysis and cooling design optimization has bee n focused on the core and the cavity, excluding other systems of injection mould s. However, the runner system introduces a considerable amount of heat into the mould. In recent years, more and more hot runner systems are being applied in th e moulding industry to save material and decrease losses of injection pressure. This raises the need to include the hot runner system in the cooling analysis. I n this paper, a photo frame part was studied. The mould was built with a hot run ner system. Two thermal sensors were installed: one measures the temperature of lateral surface of hot runner nozzle; the other measures the plastic temperature from the core side. A pressure sensor was also installed to measure the pressur e of the core impression. Cooling analysis was performed using ABAQUS, ananalysi s software based on the Finite Element Method (FEM). The assembly including core , cavity and plastic part was modeled. Heat conduction from hot runner to cavity and from polymer melt to the mould and force convection on the cooling channel surfaces were studied. The natural convection between the ambient air and the ex terior mould surface was ignored. The simulations were adjusted with the experim ental results to find out the heat input from hot runner and its influence on mo uld cooling. Finally, the optimal cooling design and optimal injection condition were obtained.

A Case Study of Heat Transfer from Hot Runner Mould to the Fix Platen of the Injection-moulding Machine

In an injection moulding process, the parallelism b et ween the tie bars of the injection moulding machine is very important as it will affect the mould closing and clamping system. In recent years, more and more ho t runner systems are being applied in the moulding industry to save material and decrease the losses of injection pressure. Heat transfer from hot runner system from the fixed half which is secured in the fix machine platen could transmit s o much heat that it may cause high temperature differential between the machine fix platen and moving platen. This will cause the tie bar to become unparallel. Part quality will be compromised and the wear of the tie bar will be excessive. Overhaul of the tie bar may be necessary after a short period of time which is c ostly. This raises the need to analyze the heat transfer from the hot runner sys tem to the machine fix platen and the methods of isolating or minimizing the hea t transfer. In this case study, a photo lens article mould was used. The mould w as built with a direct hot runner nozzle system. Heat conduction from hot runner and machine screw to machine fix platen were studied based on either using high temperature heat insulating plate put in placed between the mould and the mould ing machine fix platen or drill cooling channels in the front mould clamping pla te. The high temperature insulator is very costly as it is made out of glass re inforced polymer composite material. Experimental results were obtained and anal yzed to find the best method to minimize the unwanted heat transfer using the ch eapest and most effective method.

Effect of weld line positions on the tensile deformation of two-component metal injection moulding

Knowledge of the mechanical properties of two-component parts is critical for engineering functionally graded components. In this study, mono-and two-component tensile test specimens were metal injection moulded. Three different weld line positions were generated in the two-component specimens. Linear shrinkage of the two-component specimens was greater than that of the mono-component specimens because the incompatibility of sintering shrinkage of both materials causes biaxial stresses and enhances sintering. The mechanical properties of 316L stainless steel were affected by the addition of a coloured pigment used to identify the weld line position after injection moulding. For the two-component specimens, the yield stress and ultimate tensile stress were similar to those of 316L stainless steel. Because 316L and 630(also known as 17-4PH) stainless steels were well-sintered at the interface, the mechanical properties of the weaker material(316L stainless steel) were dominant. However, the elongations of the two-component specimens were lower than those of the mono-component specimens. An interfacial zone with a microstructure that differed from those of the mono-material specimens was observed; its different microstructure was attributed to the gradual diffusion of nickel and copper.

The most economic cavity quantity in injection mould CAD based on concurrent engineering

Presents the conception of concurrent engineering employed for CAD/CAM of injection moulds by closely combining the management science with the manufacturing techniques with the cost of processing, material cost, etc taken into consideration from the conceptural design to delivery of products and concludes with the results of analyses that the cost of finished plastic parts is lower, the production efficiency is higher while energy is saved.

Application of Standardization for Initial Design of Plastic Injection Moulds

Today, the time-to-market for plastic products ar e getting shorter, thus the lead-time for making the injection mould is decreasin g. There is potential in timesavings in the mould design stage because the design process that is repeatable for every mould design can be standardized. T he preliminary work of any final plastic injection mould design is to always pro vide an initial design of the mould assembly for product designers (customers) p rior to receiving the final product CAD data. Traditionally and even up till no w, this initial design is always created using 2D CAD packages. The information used for the initial design is based on the technical discussion checklist, in which most mould makers have their own standards. This checklist is also being used as a quotation since the most basic information of the mould in the particu lar project is being recorded in it. The basic information in this checklist in cludes the number of cavities, the type of mould base to be used, the moulding m achine to be used for the moulding, the type of gating system, the type of resin material used and its shrinkage value etc. Information on special requirements such as the number of sliders or lifters to be used is also listed in the check list. At this stage, there is still no information on the cooling and ejection design since they are greatly dependent on the final product CAD data. This res earch focuses on the methodology of providing the initial design in 3D solid bas ed on the technical discussion checklist, which takes the role of the overall st andard template since every sub-design has its own standard template. An examp le of a sub-design that has its own standard template is the cavity layout desi gn. The cavity layout for plastic injection moulds can be designed by controlli ng the geometrical parameters using a standardization template. The standardiza tion template for the cavity layout design consists of configurations for the po ssible layouts. Each configuration of the layout design has its own layout desi gn table of all the geometrical parameters. This standardization template is pr e-defined in the layout design level of the mould assembly design. This ensure s that the required configuration can be loaded into the mould assembly design v ery quickly without having the need to redesign the layout. This makes it usefu l for technical discussions between the product designers and mould designers pr ior to the manufacture of the mould. Changes can be made to the 3D cavity layou t design immediately during the discussions thus the savings in time and avo idance of miscommunications.

Optimization of Process Parameters for Injection Moulding of Nylon6/SiC and Nylon6/B_(4)C Polymer Matrix Composites

In this research study,the mechanical properties of several Polymer matrix composites are investigated.These composites are multi-phase materials in which reinforcing materials are properly mixed with a polymer matrix.More precisely,Nylon 6 reinforced with 5,15 and 25 wt.%of silicon carbide(SiC)and Nylon 6 reinforced with 5,15 and 25 wt.%of boron carbide(B_(4)C),prepared by means of an injection moulding process at three different injection pressures are considered.Specific attention is paid to the tensile and impact strength of these composites.The Taguchi technique is used to optimize the process parameters such as reinforcement material,its percentage and the injection pressure.It is observed that the specimens 5%SiC with 80 MPa injection pressure display a better tensile strength and similarly the specimen 5%B_(4)C with 90 MPa injection pressure have a superior impact strength.

Genetic Algorithm for Injection Mould Design and Moulding

Obtaining the optimal values of the parameters for th e design of a required mould and the operation of the moulding process are diffi cult, this is due to the complexity of product geometry and the variation of pla stic material properties. The typical parameters for the mould design and mouldi ng process are melt flow length, injection pressure, holding pressure, back pres sure, injection speed, melt temperature, mould temperature, clamping force, inje ction time, holding time and cooling time. This paper discusses the difficulties of using the current computer aided optimization methods to acquire the values of the parameters. A method that is based on the concept of genetic algorithm is proposed to overcome the difficulties. The proposed method describes in details on how to attain the optimal values of the parameters form a given product geom etry.

Design of Large Injection Mould for Car Dashboard

The dashboard is the most important part of the large inner decoration of cars;it should not only have enough strength and rigidity,but also have a harmonious body model which can unify the theme.Besides,it needs to reach the goal of lightweight.In order to achieve these three goals,the car dashboard is made by engineering-plastics and adopts the technology of injection moulding.This paper introduces the keys of design and the advanced technology of large injection moulding for car dashboard.

Study on the Injection Molding and Optimization of Radiator Cap based on CAE Technology

In order to improve the radiator cap of the automobile cover forming quality and efficiency, this paper applies the UG software to carry out the design of the injection mold, and use Moldflow software to simulate and analyze the position of gate filling, flow, cooling and other aspects of application, to determine the best inject location and optimize die structure design. The research results show that the combination of CAD and CAE technology can effectively improve the mold design quality, shorten die development cycle, and reduce the cost of development.

基于CAE技术的拖拉机进气管注塑模具设计

以拖拉机进气管注塑模具为研究对象,探讨了基于CAE技术的拖拉机进气管注塑模具设计方法。首先,对拖拉机进气管塑件结构和工艺性进行了深入分析;然后,详细介绍了CAE技术在拖拉机进气管塑件中的辅助设计功能;最后,针对模具浇注系统、推出机构、冷却系统、模架结构和模具结构等方面,进行了拖拉机进气管注塑模具的设计,大大提高了模具的成型效果和生产效率,避免设计过程中的试错和重复设计,节省了时间和成本。

模具局部激光熔覆耐磨涂层研究及应用

注塑模具流道出口工况苛刻,极易发生磨损,导致其形状和尺寸发生变化,对产品的质量和生产效率造成较大影响。基于此,本研究采用激光熔覆技术对注塑模具流道出口进行局部强化,针对强化涂层材料成分的设计、熔覆成形和缺陷控制、组织性能分析、实际工件加工工艺调控等开展研究。结果表明:相比商用耐磨涂层材料,所开发的涂层材料具备优异的熔覆成形和无裂纹缺陷,硬度由强化前基体硬度400HV提升至900HV以上,涂层耐磨性能相对基体提升43倍,摩擦系数由基体的0.635降至0.412,极大改善了模具的耐磨性能;强化涂层内部晶粒细小,主要由马氏体和原位陶瓷碳化物保障其耐磨性,并残留少量奥氏体保障其韧性;通过特殊的路径规划和工艺控制,在注塑模具局部强化中得到成功应用,强化后模具的服役寿命提升3倍以上。

圆弧抽芯注塑模具优化设计

基于圆弧抽芯注塑模具,根据塑件结构及材料性能特点,对浇口的位置及结构进行了优化设计,通过CAE模拟分析得到位于填充末端、最大壁厚处的塑件最大变形量为0.739 mm,变形量在设计允许范围内。以油缸作为驱动动力源,通过齿条驱动齿轮、内齿轮旋转,实现抽芯动作;将内齿轮设计为异形非标齿轮,减少了所占空间,实现了1模2腔布局。为解决圆弧型芯冷却水路难以加工的问题,设计的加工工序为先按照直型芯进行粗加工,钻孔加工型芯冷却水路,然后,将型芯加热弯曲为所需形状,并进行调质处理,最后对型芯进行精加工使其满足设计要求,达到了随形冷却效果。传动机构关键参数采用理论计算与CAE模拟分析相结合的法验证,测试结果表明,计算校核效率提高了约4倍。

基于UG的拖拉机大灯注塑模具设计

以拖拉机大灯为例,分析了UG注塑模具建模的设计方法和工艺方案,建立了拖拉机大灯模型,并完成了拖拉机大灯注塑模具的设计。研究结果表明:经过UG模拟开模出来的塑料件没有出现气泡、变形、缺料和银线等缺陷,整体也没有发现熔合条纹,设计的拖拉机大灯注塑模具满足设计需求。

矿用无线采集仪外壳双色注塑模具设计

在分析某矿用无线采集仪外壳工艺性能的基础上,采用分体式结构和一模两腔布局,设计了一副定模滑块抽芯的三板式双色模具。为实现此产品的先后两次注射成型,设计了两组不同结构的型腔和两组相同结构的型芯;针对该产品部分外表面位于动模型腔的设计难题,采用定模抽芯的方法将前壳类圆锥外表面的下半部分转为定模型腔成型,设计了定模“弯销+滑块”抽芯结构;针对前壳的型芯较高且根部存在窄缝的情况,将此型芯设计成镶件,节省了高价材料且便于加工。两次注射成型的浇注系统均采用单一点浇口进料的点浇口浇注系统,并利用软件Moldflow2021分析确定了合适浇口的位置,验证了浇注系统设计的合理性,进而可减少修模次数。针对该产品内螺纹倒扣的设计难点,将螺纹型芯设计成活动镶件,即在定模滑块和螺纹型芯内部加工带凸起的六方通孔,用销钉将带凹槽的六方轴固定于滑块,螺纹型芯可通过六方孔套入或抽出六方轴,由此简化了模具结构。该模具已投入生产,其运行顺畅、平稳,生产的双色产品质量良好。

打印机滚筒导板多点浇口注塑模设计

针对打印机滚筒导板塑件的工业设计结构特点及使用改性合金聚碳酸酯/丙烯腈-丁二烯-苯乙烯塑料成型的生产要求,设计了一副多点点浇口三板模具用于该塑件的注射成型。模具中的模腔布局为一模一腔,以使塑件成型精度控制在MT3~4级。不同于常规三板模具,在该模具中采取了以下设计措施来保证塑件的成型要求:一是通过主导柱、副导柱、模仁定位锥台等的设置,保证了塑件基本成型尺寸的成型精度;二是通过增加镶件排气措施、优化注射成型工艺参数等措施,有效降低和控制了塑件成型后的变形量,保证了塑件的成型形状精度,所增设的成型镶件有益于模腔排气,镶件间隙小于0.02 mm,镶件设计时须设计孔边扩距为1 mm,以降低镶件配模难度,避免镶件间隙飞边发生;三是为提高流道废料和塑件的冷却效率,脱料板中开设有2条?10 mm冷却水路,模腔成型件中开设有10条?10 mm冷却水路。模具中还设置了2个斜导柱滑块侧抽芯机构用于塑件两侧端面的脱模,塑件的最终脱模由多根顶针均衡顶出脱模。