To date,few models are available in the literature to consider the creep behavior of geosynthetics when predicting the lateral deformation(d)of geosynthetics-reinforced soil(GRS)retaining walls.In this study,a general...To date,few models are available in the literature to consider the creep behavior of geosynthetics when predicting the lateral deformation(d)of geosynthetics-reinforced soil(GRS)retaining walls.In this study,a general hyperbolic creep model was first introduced to describe the long-term deformation of geosynthetics,which is a function of elapsed time and two empirical parameters a and b.The conventional creep tests with three different tensile loads(Pr)were conducted on two uniaxial geogrids to determine their creep behavior,as well as the a-Pr and b-Pr relationships.The test results show that increasing Pr accelerates the development of creep deformation for both geogrids.Meanwhile,a and b respectively show exponential and negatively linear relationships with Pr,which were confirmed by abundant experimental data available in other studies.Based on the above creep model and relationships,an accurate and reliable analytical model was then proposed for predicting the time-dependent d of GRS walls with modular block facing,which was further validated using a relevant numerical investigation from the previous literature.Performance evaluation and comparison of the proposed model with six available prediction models were performed.Then a parametric study was carried out to evaluate the effects of wall height,vertical spacing of geogrids,unit weight and internal friction angle of backfills,and factor of safety against pullout on d at the end of construction and 5 years afterwards.The findings show that the creep effect not only promotes d but also raises the elevation of the maximum d along the wall height.Finally,the limitations and application prospects of the proposed model were discussed and analyzed.展开更多
It is always a challenge for a model developer to verify a three-dimensional hydrodynamic model, especially for the baroclinic term over variable topography, due to a lack of observational data sets or suitable analyt...It is always a challenge for a model developer to verify a three-dimensional hydrodynamic model, especially for the baroclinic term over variable topography, due to a lack of observational data sets or suitable analytical solutions. In this paper, exact solutions for the periodic forcing by surface heat flux and wind stress are given by solving the linearized equations of motion neglecting the rotation, advection and horizontal diffusion terms. The temperature at the bottom is set to a prescribed periodic value and a slip condition on flow is enforced at the bottom. The geometry of the quarter annulus, which has been extensively studied for two- and three-dimensional analytical solutions of unstratified water bodies, is used with a general power law variation of the bottom slope in the radial direction and is constant in the azimuthal direction. The analytical solutions are derived in a cylindrical coordinate system, which describes the three-dimensional fluid field in a Cartesian coordinate system. The results presented in this paper should provide a foundation for studying and verifying the baroclinic term over a varied topography in a three-dimensional numerical model.展开更多
A two-dimensional analytical subthreshold behavior model for junctionless dual-material cylindrical surrounding- gate (JLDMCSG) metal-oxide-semiconductor field-effect transistors (MOSFETs) is proposed. It is deriv...A two-dimensional analytical subthreshold behavior model for junctionless dual-material cylindrical surrounding- gate (JLDMCSG) metal-oxide-semiconductor field-effect transistors (MOSFETs) is proposed. It is derived by solving the two-dimensional Poisson's equation in two continuous cylindrical regions with any simplifying assumption. Using this analytical model, the subthreshold characteristics of JLDMCSG MOSFETs are investigated in terms of channel electro- static potential, horizontal electric field, and subthreshold current. Compared to junctionless single-material cylindrical surrounding-gate MOSFETs, JLDMCSG MOSFETs can effectively suppress short-channel effects and simultaneously im- prove carrier transport efficiency. It is found that the subthreshold current of JLDMCSG MOSFETs can be significantly reduced by adopting both a thin oxide and thin silicon channel. The accuracy of the analytical model is verified by its good agreement with the three-dimensional numerical simulator ISE TCAD.展开更多
In this paper, we present a two-dimensional (2D) fully analytical model with consideration of polarization effect for the channel potential and electric field distributions of the gate field-plated high electron mob...In this paper, we present a two-dimensional (2D) fully analytical model with consideration of polarization effect for the channel potential and electric field distributions of the gate field-plated high electron mobility transistor (FP-HEMT) on the basis of 2D Poisson's solution. The dependences of the channel potential and electric field distributions on drain bias, polarization charge density, FP structure parameters, A1GaN/GaN material parameters, etc. are investigated. A simple and convenient approach to designing high breakdown voltage FP-HEMTs is also proposed. The validity of this model is demonstrated by comparison with the numerical simulations with Silvaco-Atlas. The method in this paper can be extended to the development of other analytical models for different device structures, such as MIS-HEMTs, multiple-FP HETMs, slant-FP HEMTs, etc.展开更多
The utilization of stone columns has emerged as a popular ground improvement strategy,whereas the drainage performance can be adversely hampered by clogging effect.Despite the ample progress of calculation methods for...The utilization of stone columns has emerged as a popular ground improvement strategy,whereas the drainage performance can be adversely hampered by clogging effect.Despite the ample progress of calculation methods for the consolidation of stone column-improved ground,theoretical investigations into the clogging effect have not been thoroughly explored.Furthermore,it is imperative to involve the column consolidation deformation to mitigate computational error on the consolidation of composite ground with high replacement ratios.In this context,an analytical model accounting for the initial clogging and coupled time and depth-dependent clogging of stone columns is established.Then,the resulting governing equations and analytical solutions are obtained under a new flow continuity relationship to incorporate column consolidation deformation.The accuracy and reliability of the proposed model are illustrated by degradation analysis and case studies with good agreements.Subsequently,the computed results of the current study are juxtaposed against the existing models,and an in-depth assessment of the impacts of several crucial parameters on the consolidation behavior is conducted.The results reveal that ignoring column consolidation deformation leads to an overestimate of the consolidation rate,with maximum error reaching up to 16%as the replacement ratio increases.Furthermore,the initial clogging also has a significant influence on the consolidation performance.Additionally,the increment of depth and time-clogging factors a and b will induce a noticeable retardation of the consolidation process,particularly in the later stage.展开更多
The problem of shield tunnel uplift is a common issue in tunnel construction.Due to the decrease in shear stiffness at the joints between the rings,uplift is typically observed as bending and dislocation deformation a...The problem of shield tunnel uplift is a common issue in tunnel construction.Due to the decrease in shear stiffness at the joints between the rings,uplift is typically observed as bending and dislocation deformation at these joints.Existing modeling methods typically rely on the Euler-Bernoulli beam theory,only considering the bending effect while disregarding shear deformation.Furthermore,the constraints on the shield tail are often neglected in existing models.In this study,an improved theoretical model of tunnel floating is proposed.The constraint effect of the shield machine shell on the tunnel structure is considered using the structural forms of two finite long beams and one semi-infinite long beam.Furthermore,the Timoshenko beam theory is adopted,providing a more accurate description of tunnel deformation,including both the bending effect and shear deformation,than existing models.Meanwhile,the buoyancy force and stratum resistance are calculated in a nonlinear manner.A reliable method for calculating the shear stiffness correction factor is proposed to better determination of the calculation parameters.The proposed theoretical model is validated through five cases using sitemonitored data.Its applicability and effectiveness are demonstrated.Furthermore,the influences of soil type,buried depth,and buoyancy force on the three key indicators of tunnel floating(i.e.the maximum uplift magnitude,the ring position with the fastest uplift race,and the ring position with the maximum uplift magnitude)are analyzed.The results indicate that the proposed model can provide a better understanding of the floating characteristics of the tunnel structure during construction.展开更多
Surface defects,including dents,spalls,and cracks,for rolling element bearings are the most common faults in rotating machinery.The accurate model for the time-varying excitation is the basis for the vibration mechani...Surface defects,including dents,spalls,and cracks,for rolling element bearings are the most common faults in rotating machinery.The accurate model for the time-varying excitation is the basis for the vibration mechanism analysis and fault feature extraction.However,in conventional investigations,this issue is not well and fully addressed from the perspective of theoretical analysis and physical derivation.In this study,an improved analytical model for time-varying displacement excitations(TVDEs)caused by surface defects is theoretically formulated.First and foremost,the physical mechanism for the effect of defect sizes on the physical process of rolling element-defect interaction is revealed.According to the physical interaction mechanism between the rolling element and different types of defects,the relationship between time-varying displacement pulse and defect sizes is further analytically derived.With the obtained time-varying displacement pulse,the dynamic model for the deep groove bearings considering the internal excitation caused by the surface defect is established.The nonlinear vibration responses and fault features induced by surface defects are analyzed using the proposed TVDE model.The results suggest that the presence of surface defects may result in the occurrence of the dual-impulse phenomenon,which can serve as indexes for surface-defect fault diagnosis.展开更多
Waterflood-induced fractures,also known as self-induced fractures,spontaneously form at injection wells during waterflooding.These fractures propagate long distances through rock,allowing injected fluids to travel far...Waterflood-induced fractures,also known as self-induced fractures,spontaneously form at injection wells during waterflooding.These fractures propagate long distances through rock,allowing injected fluids to travel far away from a well,both within and outside the flooding layer.Essentially,the me-chanics of waterflood-induced fracture propagation is similar to that of hydraulic fractures,which are intentionally created for reservoir stimulation.Fracturing models developed for hydraulic fractures can also be applied to waterflood-induced fractures.However,waterflood-induced fractures are typically pumped with much larger volumes of water or brine and grow much longer in time.As a result,fluid leakoff from waterflood fractures into the formation is more extensive and two-dimensional(2D),a characteristic that is often ignored in a majority of modern fracturing simulators,making their appli-cation to waterflood fractures unreliable.In this work,we revisit the problem of leakoff for long-growing waterflood-induced fractures and develop a new analytical model for fluid leakoff that provides improved predictions of fracture geometry and can be easily implemented in fracturing simulators.We incorporate the developed solution into the classical Perkins-Kern-Nordgren(PKN)model of fracture growth,which shows that the choice of the Carter or a 2D leakoff model greatly impacts fracture ge-ometry at large time.The conducted parametric study shows while a toughness-dominated regime af-fects fracture evolution,most of fracture lifetime occurs in a viscosity-and-leakoff-dominated regime.We also develop an asymptotic solution for a leakoff profile in the limiting case of 2D leakoff domination(~~M and~~K).Finally,we study 3D fracture growth and out-of-zone injection with three layers and a complex structure of zones.The study shows that ignoring the 2D leakoff during simulation results in a significant overestimation of fracture geometry predictions.The present work,thus,plays an important role in improving waterflood fracture modelling,as it highlights the significance of 2D leakoff in waterflood-induced fractures and provides a reliable analytical model for fluid leakoff that can be incorporated into modern fracture simulators.展开更多
This paper describes the quasi-static testing and analytical modelling of the hysteretic behavior of aluminum alloy rigid bus-flexible connectors of 220 kV electrical substations.The main objective of the study is to ...This paper describes the quasi-static testing and analytical modelling of the hysteretic behavior of aluminum alloy rigid bus-flexible connectors of 220 kV electrical substations.The main objective of the study is to experimentally investigate the hysteretic behavior of six different types of rigid bus-flexible connectors 220 kV electrical substations when subjected to cyclic loading.Another objective is to theoretically study the flexibility and effectiveness of a previously proposed analytical model in fitting the experimental hysteresis loops of the tested rigid bus-flexible connectors.The experimental investigation indicates that the tested rigid bus-flexible connectors exhibit highly asymmetric hysteresis behavior along with tension stiffening effect.The theoretical study demonstrates that the generalized Bouc-Wen model has high flexibility and is effective in fitting the experimental hysteresis resisting force-displacement curves of the six tested rigid bus-flexible connectors.展开更多
We search for analytical wave solutions of an electronically and biologically important model named as the Fitzhugh–Nagumo model with truncated M-fractional derivative, in which the expafunction and extended sinh-Gor...We search for analytical wave solutions of an electronically and biologically important model named as the Fitzhugh–Nagumo model with truncated M-fractional derivative, in which the expafunction and extended sinh-Gordon equation expansion(ESh GEE) schemes are utilized. The solutions obtained include dark, bright, dark-bright, periodic and other kinds of solitons. These analytical wave solutions are gained and verified with the use of Mathematica software. These solutions do not exist in literature. Some of the solutions are demonstrated by 2D, 3D and contour graphs. This model is mostly used in circuit theory, transmission of nerve impulses, and population genetics. Finally, both the schemes are more applicable, reliable and significant to deal with the fractional nonlinear partial differential equations.展开更多
In this paper, the axial-flux permanent magnet driver is modeledand analyzed in a simple and novel way under three-dimensional cylindricalcoordinates. The inherent three-dimensional characteristics of the deviceare co...In this paper, the axial-flux permanent magnet driver is modeledand analyzed in a simple and novel way under three-dimensional cylindricalcoordinates. The inherent three-dimensional characteristics of the deviceare comprehensively considered, and the governing equations are solved bysimplifying the boundary conditions. The axial magnetization of the sectorshapedpermanent magnets is accurately described in an algebraic form bythe parameters, which makes the physical meaning more explicit than thepurely mathematical expression in general series forms. The parameters of theBessel function are determined simply and the magnetic field distribution ofpermanent magnets and the air-gap is solved. Furthermore, the field solutionsare completely analytical, which provides convenience and satisfactoryaccuracy for modeling a series of electromagnetic performance parameters,such as the axial electromagnetic force density, axial electromagnetic force,and electromagnetic torque. The correctness and accuracy of the analyticalmodels are fully verified by three-dimensional finite element simulations and a15 kW prototype and the results of calculations, simulations, and experimentsunder three methods are highly consistent. The influence of several designparameters on magnetic field distribution and performance is studied and discussed.The results indicate that the modeling method proposed in this papercan calculate the magnetic field distribution and performance accurately andrapidly, which affords an important reference for the design and optimizationof axial-flux permanent magnet drivers.展开更多
This study proposed the newly-designed Pelagic and demersal trawls for the fishing vessels operating in Cameroonian waters in pelagic and demersal fishing grounds. The engineering performances of both trawls were inve...This study proposed the newly-designed Pelagic and demersal trawls for the fishing vessels operating in Cameroonian waters in pelagic and demersal fishing grounds. The engineering performances of both trawls were investigated using physical modelling method and analytical method based on the predicted equations. In a flume tank, a series of physical model tests based on Tauti’s law were performed to investigate the hydrodynamic and geometrical performances of both trawls and to assess the applicability of the analytical methods based on predicted equations. The results showed that in model scale, the working towing speed and door spread for the pelagic trawl were 3.5 knots and 1.85 m, respectively, and for the bottom trawl net they were 4.0 knots and 1.8 m. At that speed and door spread, the drag force, net opening height, and wing-end spread of the pelagic model trawl were 36.73 N, 0.89 m, and 0.86 m, respectively, and the swept area was 0.76 m<sup>2</sup>. Bottom trawl speed and door spread were 30.43 N, 0.38 m, and 0.45 m, respectively, and the swept area was 0.25 m<sup>2</sup>. The maximum difference between the experimental and analytical results of hydrodynamic performances was less than 56.22% and 41.45%, respectively, for pelagic and bottom trawls, the results of the geometrical performances obtained using predicted equations were close to the experimental results in the flume tank with a maximum relative error less than 12.85%. The newly developed pelagic and bottom trawls had advanced engineering performance for high catch efficiency and selectivity and could be used in commercial fishing operations in Cameroonian waters.展开更多
Based on analyzing the influences of a slicing scheme on stair-stepping effect, supporting structure, efficiency and deformation, etc. , analytical hierarchical process (AHP) combining with fuzzy synthetic evaluatio...Based on analyzing the influences of a slicing scheme on stair-stepping effect, supporting structure, efficiency and deformation, etc. , analytical hierarchical process (AHP) combining with fuzzy synthetic evaluation is introduced to make decision in slicing schemes for a processing part. The application in determining the slicing scheme for a computer mouse during prototyping shows that the method increases the rationality during decision- making and improves quality and efficiency for the prototyping part.展开更多
Departing from an analytical phase transformation model, a new analytical approach to deduce transformed fraction for non-isothermal phase transformation was developed. In the new approach, the effect of the initial t...Departing from an analytical phase transformation model, a new analytical approach to deduce transformed fraction for non-isothermal phase transformation was developed. In the new approach, the effect of the initial transformation temperature and the accurate "temperature integral" approximations are incorporated to obtain an extended analytical model. Numerical approach demonstrated that the extended analytical model prediction for transformed fraction and transformation rate is in good agreement with the exact numerical calculation. The new model can describe more precisely the kinetic behavior than the original analytical model, especially for transformation with relatively high initial transformation temperature. The kinetic parameters obtained from the new model are more accurate and reasonable than those from the original analytical model.展开更多
Due to interaction among cells, it is too complex to build an exactanalytical model for the power dissipation within the cell membrane in suspensions exposed toexternal fields. An approximate equivalence method is pro...Due to interaction among cells, it is too complex to build an exactanalytical model for the power dissipation within the cell membrane in suspensions exposed toexternal fields. An approximate equivalence method is proposed to resolve this problem. Based on theeffective medium theory, the transmembrane voltage on cells in suspensions was investigated by theequivalence principle. Then the electric field in the cell membrane was determined. Finally,analytical solutions for the power dissipation within the cell membrane in suspensions exposed toexternal fields were derived according to the Joule principle. The equations show that theconductive power dissipation is predominant within the cell membrane in suspensions exposed todirect current or lower frequencies, and dielectric power dissipation prevails at high frequenciesexceeding the relaxation frequency of the exposed membrane.展开更多
An analytical model of electron mobility for strained-silicon channel nMOSFETs is proposed in this paper. The model deals directly with the strain tensor,and thus is independent of the manufacturing process. It is sui...An analytical model of electron mobility for strained-silicon channel nMOSFETs is proposed in this paper. The model deals directly with the strain tensor,and thus is independent of the manufacturing process. It is suitable for (100〉/ 〈110) channel nMOSFETs under biaxial or (100〉/〈 110 ) uniaxial stress and can be implemented in conventional device simulation tools .展开更多
The small-scale drilling technique can be a fast and reliable method to estimate rock strength parameters. It needs to link the operational drilling parameters and strength properties of rock. The parameters such as b...The small-scale drilling technique can be a fast and reliable method to estimate rock strength parameters. It needs to link the operational drilling parameters and strength properties of rock. The parameters such as bit geometry, bit movement, contact frictions and crushed zone affect the estimated parameters.An analytical model considering operational drilling data and effective parameters can be used for these purposes. In this research, an analytical model was developed based on limit equilibrium of forces in a Tshaped drag bit considering the effective parameters such as bit geometry, crushed zone and contact frictions in drilling process. Based on the model, a method was used to estimate rock strength parameters such as cohesion, internal friction angle and uniaxial compressive strength of different rock types from operational drilling data. Some drilling tests were conducted by a portable and powerful drilling machine which was developed for this work. The obtained results for strength properties of different rock types from the drilling experiments based on the proposed model are in good agreement with the results of standard tests. Experimental results show that the contact friction between the cutting face and rock is close to that between bit end wearing face and rock due to the same bit material. In this case,the strength parameters, especially internal friction angle and cohesion, are estimated only by using a blunt bit drilling data and the bit bluntness does not affect the estimated results.展开更多
In this paper,an analytical model that represents the streamwise velocity distribution for open channel flow with submerged flexible vegetation is studied.In the present vegetated flow modelling,the whole flow field h...In this paper,an analytical model that represents the streamwise velocity distribution for open channel flow with submerged flexible vegetation is studied.In the present vegetated flow modelling,the whole flow field has been separated into two layers vertically: a vegetated layer and a non-vegetated free-water layer.Within the vegetated layer,an analysis of the mechanisms affecting water flow through flexible vegetation has been conducted.In the non-vegetated layer,a modified log-law equation that represents the velocity profile varying with vegetation height has been investigated.Based on the studied analytical model,a sensitivity analysis has been conducted to assess the influences of the drag (CD) and friction (Cf ) coefficients on the flow velocity.The investigated ranges of CD and Cf have also been compared to published values.The findings suggest that the CD and Cf values are non-constant at different depths and vegetation densities,unlike the constant values commonly suggested in literature.This phenomenon is particularly clear for flows with flexible vegetation,which is characterised by large deflection.展开更多
Fully grouted rock bolts have been used in mining industry for many years.Much research has been conducted to evaluate the load transfer behavior of fully grouted rock bolts with experimental programs.However,compared...Fully grouted rock bolts have been used in mining industry for many years.Much research has been conducted to evaluate the load transfer behavior of fully grouted rock bolts with experimental programs.However,compared with that,less work has been conducted with analytical modelling.Therefore,in this paper,the authors used an analytical model to study the load transfer behavior of fully grouted rock bolts.To confirm the credibility of this analytical model,an in-situ pull-out test was used to validate this model.There was a close match between the experimental result and the analytical result.Following it,a parametric study was conducted with this analytical model.The influence of coefficients,Young’s modulus of the rock bolt and the diameter of the rock bolt on the load transfer performance of rock bolts was studied.Furthermore,the load distribution along the fully grouted rock bolt was analytically studied.The results show that the axial load in the rock bolt decayed from the loaded end to the free end independent of the pull-out load.However,the trend of the load distribution curve was influenced by the pull-out load.This paper was beneficial for better understanding the load transfer mechanism of fully grouted rock bolts.展开更多
Radius of ceramic cone can largely contribute into final solution of analytic models of penetration into ceramic/metal targets.In the present research,a modified model based on radius of ceramic cone was presented for...Radius of ceramic cone can largely contribute into final solution of analytic models of penetration into ceramic/metal targets.In the present research,a modified model based on radius of ceramic cone was presented for ceramic/aluminum targets.In order to investigate and evaluate accuracy of the presented analytic model,obtained results were compared against the results of the Florence’s analytic model and also against numerical modeling results.The phenomenon of impact onto ceramic/aluminum composites were modeled using smoothed particle hydrodynamics(SPH)implemented utilizing ABAQUS Software.Results indicated that,with increasing initial velocity and ceramic thickness and decreasing support layer thickness,the radius of ceramic cone decreases;this ends up increasing residual velocity of the projectile and penetration time and extending the area across which the pressure is distributed.These findings indicate enhanced levels of target energy absorption and the required energy for bending and tensioning the target.As such,it can be observed that,at the same thickness and areal density,the ceramic target has its efficiency enhanced with increasing ceramic thickness and decreasing the support layer thickness.Finally,the results revealed that the associated data with SPH confirm the modified analytic model at higher accuracy than the Florence’s analytic model.展开更多
基金This research work was financially supported by the National Natural Science Foundation of China(Grant Nos.52078182 and 41877255)the Tianjin Municipal Natural Science Foundation(Grant No.20JCYBJC00630).Their financial support is gratefully acknowledged.
文摘To date,few models are available in the literature to consider the creep behavior of geosynthetics when predicting the lateral deformation(d)of geosynthetics-reinforced soil(GRS)retaining walls.In this study,a general hyperbolic creep model was first introduced to describe the long-term deformation of geosynthetics,which is a function of elapsed time and two empirical parameters a and b.The conventional creep tests with three different tensile loads(Pr)were conducted on two uniaxial geogrids to determine their creep behavior,as well as the a-Pr and b-Pr relationships.The test results show that increasing Pr accelerates the development of creep deformation for both geogrids.Meanwhile,a and b respectively show exponential and negatively linear relationships with Pr,which were confirmed by abundant experimental data available in other studies.Based on the above creep model and relationships,an accurate and reliable analytical model was then proposed for predicting the time-dependent d of GRS walls with modular block facing,which was further validated using a relevant numerical investigation from the previous literature.Performance evaluation and comparison of the proposed model with six available prediction models were performed.Then a parametric study was carried out to evaluate the effects of wall height,vertical spacing of geogrids,unit weight and internal friction angle of backfills,and factor of safety against pullout on d at the end of construction and 5 years afterwards.The findings show that the creep effect not only promotes d but also raises the elevation of the maximum d along the wall height.Finally,the limitations and application prospects of the proposed model were discussed and analyzed.
文摘It is always a challenge for a model developer to verify a three-dimensional hydrodynamic model, especially for the baroclinic term over variable topography, due to a lack of observational data sets or suitable analytical solutions. In this paper, exact solutions for the periodic forcing by surface heat flux and wind stress are given by solving the linearized equations of motion neglecting the rotation, advection and horizontal diffusion terms. The temperature at the bottom is set to a prescribed periodic value and a slip condition on flow is enforced at the bottom. The geometry of the quarter annulus, which has been extensively studied for two- and three-dimensional analytical solutions of unstratified water bodies, is used with a general power law variation of the bottom slope in the radial direction and is constant in the azimuthal direction. The analytical solutions are derived in a cylindrical coordinate system, which describes the three-dimensional fluid field in a Cartesian coordinate system. The results presented in this paper should provide a foundation for studying and verifying the baroclinic term over a varied topography in a three-dimensional numerical model.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.61204092 and 61076101)the Fundamental Research Funds for the Central Universities of Ministry of Education of China(Grant No.K50511250001)
文摘A two-dimensional analytical subthreshold behavior model for junctionless dual-material cylindrical surrounding- gate (JLDMCSG) metal-oxide-semiconductor field-effect transistors (MOSFETs) is proposed. It is derived by solving the two-dimensional Poisson's equation in two continuous cylindrical regions with any simplifying assumption. Using this analytical model, the subthreshold characteristics of JLDMCSG MOSFETs are investigated in terms of channel electro- static potential, horizontal electric field, and subthreshold current. Compared to junctionless single-material cylindrical surrounding-gate MOSFETs, JLDMCSG MOSFETs can effectively suppress short-channel effects and simultaneously im- prove carrier transport efficiency. It is found that the subthreshold current of JLDMCSG MOSFETs can be significantly reduced by adopting both a thin oxide and thin silicon channel. The accuracy of the analytical model is verified by its good agreement with the three-dimensional numerical simulator ISE TCAD.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.61204085 and 61334002)the Fundamental Research Funds for the Central Universities,China(Grant No.K5051225013)
文摘In this paper, we present a two-dimensional (2D) fully analytical model with consideration of polarization effect for the channel potential and electric field distributions of the gate field-plated high electron mobility transistor (FP-HEMT) on the basis of 2D Poisson's solution. The dependences of the channel potential and electric field distributions on drain bias, polarization charge density, FP structure parameters, A1GaN/GaN material parameters, etc. are investigated. A simple and convenient approach to designing high breakdown voltage FP-HEMTs is also proposed. The validity of this model is demonstrated by comparison with the numerical simulations with Silvaco-Atlas. The method in this paper can be extended to the development of other analytical models for different device structures, such as MIS-HEMTs, multiple-FP HETMs, slant-FP HEMTs, etc.
基金funding support from the National Natural Science Foundation of China(Grant Nos.52178373 and 51878657).
文摘The utilization of stone columns has emerged as a popular ground improvement strategy,whereas the drainage performance can be adversely hampered by clogging effect.Despite the ample progress of calculation methods for the consolidation of stone column-improved ground,theoretical investigations into the clogging effect have not been thoroughly explored.Furthermore,it is imperative to involve the column consolidation deformation to mitigate computational error on the consolidation of composite ground with high replacement ratios.In this context,an analytical model accounting for the initial clogging and coupled time and depth-dependent clogging of stone columns is established.Then,the resulting governing equations and analytical solutions are obtained under a new flow continuity relationship to incorporate column consolidation deformation.The accuracy and reliability of the proposed model are illustrated by degradation analysis and case studies with good agreements.Subsequently,the computed results of the current study are juxtaposed against the existing models,and an in-depth assessment of the impacts of several crucial parameters on the consolidation behavior is conducted.The results reveal that ignoring column consolidation deformation leads to an overestimate of the consolidation rate,with maximum error reaching up to 16%as the replacement ratio increases.Furthermore,the initial clogging also has a significant influence on the consolidation performance.Additionally,the increment of depth and time-clogging factors a and b will induce a noticeable retardation of the consolidation process,particularly in the later stage.
基金the National Natural Science Foundation of China (Grant Nos.52379111,51979270 and 52208380).
文摘The problem of shield tunnel uplift is a common issue in tunnel construction.Due to the decrease in shear stiffness at the joints between the rings,uplift is typically observed as bending and dislocation deformation at these joints.Existing modeling methods typically rely on the Euler-Bernoulli beam theory,only considering the bending effect while disregarding shear deformation.Furthermore,the constraints on the shield tail are often neglected in existing models.In this study,an improved theoretical model of tunnel floating is proposed.The constraint effect of the shield machine shell on the tunnel structure is considered using the structural forms of two finite long beams and one semi-infinite long beam.Furthermore,the Timoshenko beam theory is adopted,providing a more accurate description of tunnel deformation,including both the bending effect and shear deformation,than existing models.Meanwhile,the buoyancy force and stratum resistance are calculated in a nonlinear manner.A reliable method for calculating the shear stiffness correction factor is proposed to better determination of the calculation parameters.The proposed theoretical model is validated through five cases using sitemonitored data.Its applicability and effectiveness are demonstrated.Furthermore,the influences of soil type,buried depth,and buoyancy force on the three key indicators of tunnel floating(i.e.the maximum uplift magnitude,the ring position with the fastest uplift race,and the ring position with the maximum uplift magnitude)are analyzed.The results indicate that the proposed model can provide a better understanding of the floating characteristics of the tunnel structure during construction.
基金This work is sponsored by the National Natural Science Foundation of China(Nos.52105117&52105118).
文摘Surface defects,including dents,spalls,and cracks,for rolling element bearings are the most common faults in rotating machinery.The accurate model for the time-varying excitation is the basis for the vibration mechanism analysis and fault feature extraction.However,in conventional investigations,this issue is not well and fully addressed from the perspective of theoretical analysis and physical derivation.In this study,an improved analytical model for time-varying displacement excitations(TVDEs)caused by surface defects is theoretically formulated.First and foremost,the physical mechanism for the effect of defect sizes on the physical process of rolling element-defect interaction is revealed.According to the physical interaction mechanism between the rolling element and different types of defects,the relationship between time-varying displacement pulse and defect sizes is further analytically derived.With the obtained time-varying displacement pulse,the dynamic model for the deep groove bearings considering the internal excitation caused by the surface defect is established.The nonlinear vibration responses and fault features induced by surface defects are analyzed using the proposed TVDE model.The results suggest that the presence of surface defects may result in the occurrence of the dual-impulse phenomenon,which can serve as indexes for surface-defect fault diagnosis.
文摘Waterflood-induced fractures,also known as self-induced fractures,spontaneously form at injection wells during waterflooding.These fractures propagate long distances through rock,allowing injected fluids to travel far away from a well,both within and outside the flooding layer.Essentially,the me-chanics of waterflood-induced fracture propagation is similar to that of hydraulic fractures,which are intentionally created for reservoir stimulation.Fracturing models developed for hydraulic fractures can also be applied to waterflood-induced fractures.However,waterflood-induced fractures are typically pumped with much larger volumes of water or brine and grow much longer in time.As a result,fluid leakoff from waterflood fractures into the formation is more extensive and two-dimensional(2D),a characteristic that is often ignored in a majority of modern fracturing simulators,making their appli-cation to waterflood fractures unreliable.In this work,we revisit the problem of leakoff for long-growing waterflood-induced fractures and develop a new analytical model for fluid leakoff that provides improved predictions of fracture geometry and can be easily implemented in fracturing simulators.We incorporate the developed solution into the classical Perkins-Kern-Nordgren(PKN)model of fracture growth,which shows that the choice of the Carter or a 2D leakoff model greatly impacts fracture ge-ometry at large time.The conducted parametric study shows while a toughness-dominated regime af-fects fracture evolution,most of fracture lifetime occurs in a viscosity-and-leakoff-dominated regime.We also develop an asymptotic solution for a leakoff profile in the limiting case of 2D leakoff domination(~~M and~~K).Finally,we study 3D fracture growth and out-of-zone injection with three layers and a complex structure of zones.The study shows that ignoring the 2D leakoff during simulation results in a significant overestimation of fracture geometry predictions.The present work,thus,plays an important role in improving waterflood fracture modelling,as it highlights the significance of 2D leakoff in waterflood-induced fractures and provides a reliable analytical model for fluid leakoff that can be incorporated into modern fracture simulators.
基金National Natural Science Foundation of China under Grant No.51978397。
文摘This paper describes the quasi-static testing and analytical modelling of the hysteretic behavior of aluminum alloy rigid bus-flexible connectors of 220 kV electrical substations.The main objective of the study is to experimentally investigate the hysteretic behavior of six different types of rigid bus-flexible connectors 220 kV electrical substations when subjected to cyclic loading.Another objective is to theoretically study the flexibility and effectiveness of a previously proposed analytical model in fitting the experimental hysteresis loops of the tested rigid bus-flexible connectors.The experimental investigation indicates that the tested rigid bus-flexible connectors exhibit highly asymmetric hysteresis behavior along with tension stiffening effect.The theoretical study demonstrates that the generalized Bouc-Wen model has high flexibility and is effective in fitting the experimental hysteresis resisting force-displacement curves of the six tested rigid bus-flexible connectors.
文摘We search for analytical wave solutions of an electronically and biologically important model named as the Fitzhugh–Nagumo model with truncated M-fractional derivative, in which the expafunction and extended sinh-Gordon equation expansion(ESh GEE) schemes are utilized. The solutions obtained include dark, bright, dark-bright, periodic and other kinds of solitons. These analytical wave solutions are gained and verified with the use of Mathematica software. These solutions do not exist in literature. Some of the solutions are demonstrated by 2D, 3D and contour graphs. This model is mostly used in circuit theory, transmission of nerve impulses, and population genetics. Finally, both the schemes are more applicable, reliable and significant to deal with the fractional nonlinear partial differential equations.
基金supported by the National Natural Science Foundation of China under Grant[52077027]Liaoning Province Science and Technology Major Project[No.2020JH1/10100020].
文摘In this paper, the axial-flux permanent magnet driver is modeledand analyzed in a simple and novel way under three-dimensional cylindricalcoordinates. The inherent three-dimensional characteristics of the deviceare comprehensively considered, and the governing equations are solved bysimplifying the boundary conditions. The axial magnetization of the sectorshapedpermanent magnets is accurately described in an algebraic form bythe parameters, which makes the physical meaning more explicit than thepurely mathematical expression in general series forms. The parameters of theBessel function are determined simply and the magnetic field distribution ofpermanent magnets and the air-gap is solved. Furthermore, the field solutionsare completely analytical, which provides convenience and satisfactoryaccuracy for modeling a series of electromagnetic performance parameters,such as the axial electromagnetic force density, axial electromagnetic force,and electromagnetic torque. The correctness and accuracy of the analyticalmodels are fully verified by three-dimensional finite element simulations and a15 kW prototype and the results of calculations, simulations, and experimentsunder three methods are highly consistent. The influence of several designparameters on magnetic field distribution and performance is studied and discussed.The results indicate that the modeling method proposed in this papercan calculate the magnetic field distribution and performance accurately andrapidly, which affords an important reference for the design and optimizationof axial-flux permanent magnet drivers.
文摘This study proposed the newly-designed Pelagic and demersal trawls for the fishing vessels operating in Cameroonian waters in pelagic and demersal fishing grounds. The engineering performances of both trawls were investigated using physical modelling method and analytical method based on the predicted equations. In a flume tank, a series of physical model tests based on Tauti’s law were performed to investigate the hydrodynamic and geometrical performances of both trawls and to assess the applicability of the analytical methods based on predicted equations. The results showed that in model scale, the working towing speed and door spread for the pelagic trawl were 3.5 knots and 1.85 m, respectively, and for the bottom trawl net they were 4.0 knots and 1.8 m. At that speed and door spread, the drag force, net opening height, and wing-end spread of the pelagic model trawl were 36.73 N, 0.89 m, and 0.86 m, respectively, and the swept area was 0.76 m<sup>2</sup>. Bottom trawl speed and door spread were 30.43 N, 0.38 m, and 0.45 m, respectively, and the swept area was 0.25 m<sup>2</sup>. The maximum difference between the experimental and analytical results of hydrodynamic performances was less than 56.22% and 41.45%, respectively, for pelagic and bottom trawls, the results of the geometrical performances obtained using predicted equations were close to the experimental results in the flume tank with a maximum relative error less than 12.85%. The newly developed pelagic and bottom trawls had advanced engineering performance for high catch efficiency and selectivity and could be used in commercial fishing operations in Cameroonian waters.
基金Supported by the Science and Technology Support Key Project of Jiangsu Province (DE2008365)~~
文摘Based on analyzing the influences of a slicing scheme on stair-stepping effect, supporting structure, efficiency and deformation, etc. , analytical hierarchical process (AHP) combining with fuzzy synthetic evaluation is introduced to make decision in slicing schemes for a processing part. The application in determining the slicing scheme for a computer mouse during prototyping shows that the method increases the rationality during decision- making and improves quality and efficiency for the prototyping part.
基金Projects (09-QZ-2008, 24-TZ-2009) supported by the Free Research Fund of State Key Laboratory of Solidification Processing, ChinaProject (B08040) supported by the Program of Introducing Talents of Discipline to Universities, China+3 种基金Projects (51071127, 51134011) supported by the National Natural Science Foundation of ChinaProject (JC200801) supported by the Fundamental Research Fund of Northwestern Polytechnical University, ChinaProject (51125002) supported by the National Science Foundation for Distinguished Young Scholars, ChinaProject (2011CB610403) supported by the National Basic Research Program of China
文摘Departing from an analytical phase transformation model, a new analytical approach to deduce transformed fraction for non-isothermal phase transformation was developed. In the new approach, the effect of the initial transformation temperature and the accurate "temperature integral" approximations are incorporated to obtain an extended analytical model. Numerical approach demonstrated that the extended analytical model prediction for transformed fraction and transformation rate is in good agreement with the exact numerical calculation. The new model can describe more precisely the kinetic behavior than the original analytical model, especially for transformation with relatively high initial transformation temperature. The kinetic parameters obtained from the new model are more accurate and reasonable than those from the original analytical model.
文摘Due to interaction among cells, it is too complex to build an exactanalytical model for the power dissipation within the cell membrane in suspensions exposed toexternal fields. An approximate equivalence method is proposed to resolve this problem. Based on theeffective medium theory, the transmembrane voltage on cells in suspensions was investigated by theequivalence principle. Then the electric field in the cell membrane was determined. Finally,analytical solutions for the power dissipation within the cell membrane in suspensions exposed toexternal fields were derived according to the Joule principle. The equations show that theconductive power dissipation is predominant within the cell membrane in suspensions exposed todirect current or lower frequencies, and dielectric power dissipation prevails at high frequenciesexceeding the relaxation frequency of the exposed membrane.
文摘An analytical model of electron mobility for strained-silicon channel nMOSFETs is proposed in this paper. The model deals directly with the strain tensor,and thus is independent of the manufacturing process. It is suitable for (100〉/ 〈110) channel nMOSFETs under biaxial or (100〉/〈 110 ) uniaxial stress and can be implemented in conventional device simulation tools .
文摘The small-scale drilling technique can be a fast and reliable method to estimate rock strength parameters. It needs to link the operational drilling parameters and strength properties of rock. The parameters such as bit geometry, bit movement, contact frictions and crushed zone affect the estimated parameters.An analytical model considering operational drilling data and effective parameters can be used for these purposes. In this research, an analytical model was developed based on limit equilibrium of forces in a Tshaped drag bit considering the effective parameters such as bit geometry, crushed zone and contact frictions in drilling process. Based on the model, a method was used to estimate rock strength parameters such as cohesion, internal friction angle and uniaxial compressive strength of different rock types from operational drilling data. Some drilling tests were conducted by a portable and powerful drilling machine which was developed for this work. The obtained results for strength properties of different rock types from the drilling experiments based on the proposed model are in good agreement with the results of standard tests. Experimental results show that the contact friction between the cutting face and rock is close to that between bit end wearing face and rock due to the same bit material. In this case,the strength parameters, especially internal friction angle and cohesion, are estimated only by using a blunt bit drilling data and the bit bluntness does not affect the estimated results.
文摘In this paper,an analytical model that represents the streamwise velocity distribution for open channel flow with submerged flexible vegetation is studied.In the present vegetated flow modelling,the whole flow field has been separated into two layers vertically: a vegetated layer and a non-vegetated free-water layer.Within the vegetated layer,an analysis of the mechanisms affecting water flow through flexible vegetation has been conducted.In the non-vegetated layer,a modified log-law equation that represents the velocity profile varying with vegetation height has been investigated.Based on the studied analytical model,a sensitivity analysis has been conducted to assess the influences of the drag (CD) and friction (Cf ) coefficients on the flow velocity.The investigated ranges of CD and Cf have also been compared to published values.The findings suggest that the CD and Cf values are non-constant at different depths and vegetation densities,unlike the constant values commonly suggested in literature.This phenomenon is particularly clear for flows with flexible vegetation,which is characterised by large deflection.
基金supported by the National Natural Science Foundation of China (Nos. 51574243 and 51904302)the Yue Qi Distinguished Scholar Project of China (No. 800015Z1138)+1 种基金China University of Mining and Technology, Beijingthe Fundamental Research Funds for the Central Universities, China (No.800015J6)。
文摘Fully grouted rock bolts have been used in mining industry for many years.Much research has been conducted to evaluate the load transfer behavior of fully grouted rock bolts with experimental programs.However,compared with that,less work has been conducted with analytical modelling.Therefore,in this paper,the authors used an analytical model to study the load transfer behavior of fully grouted rock bolts.To confirm the credibility of this analytical model,an in-situ pull-out test was used to validate this model.There was a close match between the experimental result and the analytical result.Following it,a parametric study was conducted with this analytical model.The influence of coefficients,Young’s modulus of the rock bolt and the diameter of the rock bolt on the load transfer performance of rock bolts was studied.Furthermore,the load distribution along the fully grouted rock bolt was analytically studied.The results show that the axial load in the rock bolt decayed from the loaded end to the free end independent of the pull-out load.However,the trend of the load distribution curve was influenced by the pull-out load.This paper was beneficial for better understanding the load transfer mechanism of fully grouted rock bolts.
文摘Radius of ceramic cone can largely contribute into final solution of analytic models of penetration into ceramic/metal targets.In the present research,a modified model based on radius of ceramic cone was presented for ceramic/aluminum targets.In order to investigate and evaluate accuracy of the presented analytic model,obtained results were compared against the results of the Florence’s analytic model and also against numerical modeling results.The phenomenon of impact onto ceramic/aluminum composites were modeled using smoothed particle hydrodynamics(SPH)implemented utilizing ABAQUS Software.Results indicated that,with increasing initial velocity and ceramic thickness and decreasing support layer thickness,the radius of ceramic cone decreases;this ends up increasing residual velocity of the projectile and penetration time and extending the area across which the pressure is distributed.These findings indicate enhanced levels of target energy absorption and the required energy for bending and tensioning the target.As such,it can be observed that,at the same thickness and areal density,the ceramic target has its efficiency enhanced with increasing ceramic thickness and decreasing the support layer thickness.Finally,the results revealed that the associated data with SPH confirm the modified analytic model at higher accuracy than the Florence’s analytic model.