The High-energy Fragment Separator(HFRS),which is currently under construction,is a leading international radioactive beam device.Multiple sets of position-sensitive twin time projection chamber(TPC)detectors are dist...The High-energy Fragment Separator(HFRS),which is currently under construction,is a leading international radioactive beam device.Multiple sets of position-sensitive twin time projection chamber(TPC)detectors are distributed on HFRS for particle identification and beam monitoring.The twin TPCs'readout electronics system operates in a trigger-less mode due to its high counting rate,leading to a challenge of handling large amounts of data.To address this problem,we introduced an event-building algorithm.This algorithm employs a hierarchical processing strategy to compress data during transmission and aggregation.In addition,it reconstructs twin TPCs'events online and stores only the reconstructed particle information,which significantly reduces the burden on data transmission and storage resources.Simulation studies demonstrated that the algorithm accurately matches twin TPCs'events and reduces more than 98%of the data volume at a counting rate of 500 kHz/channel.展开更多
The comprehensive tire building and shaping processes are investigated through the finite element method(FEM)in this article.The mechanical properties of the uncured rubber from different tire components are investiga...The comprehensive tire building and shaping processes are investigated through the finite element method(FEM)in this article.The mechanical properties of the uncured rubber from different tire components are investigated through cyclic loading-unloading experiments under different strain rates.Based on the experiments,an elastoviscoplastic constitutive model is adopted to describe themechanical behaviors of the uncured rubber.The distinct mechanical properties,including the stress level,hysteresis and residual strain,of the uncured rubber can all be well characterized.The whole tire building process(including component winding,rubber bladder inflation,component stitching and carcass band folding-back)and the shaping process are simulated using this constitutive model.The simulated green tire profile is in good agreement with the actual profile obtained through 3D scanning.The deformation and stress of the rubber components and the cord reinforcements during production can be obtained fromthe FE simulation,which is helpful for judging the rationality of the tire construction design.Finally,the influence of the parameter“drum width”is investigated,and the simulated result is found to be consistent with the experimental observations,which verifies the effectiveness of the simulation.The established simulation strategy provides some guiding significance for the improvement of tire design parameters and the elimination of tire production defects.展开更多
Urbanization has led to the rapid development of the construction industry.However,this has also led to higher requirements for the construction engineering management.Other than the quality monitoring of engineering ...Urbanization has led to the rapid development of the construction industry.However,this has also led to higher requirements for the construction engineering management.Other than the quality monitoring of engineering construction,the energy-saving properties of the building should also be considered.Therefore,a scientific management approach should be adopted to improve green building management.This paper primarily examines the importance of quality management in green building construction,along with the factors influencing it.It also identifies the quality issues present in current green building construction.Finally,it proposes measures for quality management in the green building construction process to facilitate the industry’s healthy development.展开更多
The two-stage dough mixing process was innovated to improve the qualities of bread made from potato flour(PF) and wheat flour at a ratio of 1:1(w/w). The final dough was first prepared from wheat flour before being ad...The two-stage dough mixing process was innovated to improve the qualities of bread made from potato flour(PF) and wheat flour at a ratio of 1:1(w/w). The final dough was first prepared from wheat flour before being added with PF. The effects of the method on enhancing the dough qualities were verified, and the distribution of water in gluten-gelatinized starch matrix of the doughs was investigated. We observed that the bread qualities were improved, as reflected by the increase of specific volume from 2.26 to 2.96 m L g^–1 and the decrease of crumb hardness from 417.93 to 255.57 g. The results from rheofermentometric measurements showed that the dough mixed using the developed mixing method had higher maximum dough height value, time of dough porosity appearance, and gas retention coefficient, as well as enhanced gluten matrix formation compared to that mixed by the traditional mixing method. The results from low-field nuclear magnetic resonance confirmed that the competitive water absorption between gluten and gelatinized starch could restrict the formation of gluten network in the dough mixed using the traditional mixing process. Using the novel mixing method, gluten could be sufficiently hydrated in stage 1, which could then weaken the competitive water absorption caused by gelatinized starch in stage 2;this could also be indicated by the greater mobility of proton in PF and better development of gluten network during mixing.展开更多
As an important element in sustainable building design, the building envelope has been witnessing a constant shift in the design approach. Integrating multi-objective optimization(MOO) into the building envelope desig...As an important element in sustainable building design, the building envelope has been witnessing a constant shift in the design approach. Integrating multi-objective optimization(MOO) into the building envelope design process is very promising, but not easy to realize in an actual project due to several factors, including the complexity of optimization model construction, lack of a dynamic-visualization capacity in the simulation tools and consideration of how to match the optimization with the actual design process. To overcome these difficulties, this study constructed an integrated building envelope design process(IBEDP) based on parametric modelling, which was implemented using Grasshopper platform and interfaces to control the simulation software and optimization algorithm. A railway station was selected as a case study for applying the proposed IBEDP, which also utilized a grid-based variable design approach to achieve flexible optimum fenestrations. To facilitate the stepwise design process, a novel strategy was proposed with a two-step optimization, which optimized various categories of variables separately. Compared with a one-step optimization,though the proposed strategy performed poorly in the diversity of solutions, the quantitative assessment of the qualities of Pareto-optimum solution sets illustrates that it is superior.展开更多
Based on the characteristics of pickling wastewater in the cold-rolling production of stainless steel, a new processing route, featuring source sludge reduction, wastewater two-stage treatment, heavy metal-contained s...Based on the characteristics of pickling wastewater in the cold-rolling production of stainless steel, a new processing route, featuring source sludge reduction, wastewater two-stage treatment, heavy metal-contained sludge and calcium salt sludge separating recovery, was proposed. As shown by the research results, after the two-stage process treatment, the effluent water can steadily reach the emission standards, the sludge yield can be decreased by more than 8% ; within the heavy metal-contained sludge, the recovery rates of Fc,Cr and Ni can either reach or surpass 95% ,and the total content ofF and S can drop to around 3%. Therefore,the sludge in the front part can be used as ferric dust. In the calcium salt sludge ,the recovery rate of F can either reach or surpass 85% ,and the total contents of Fe,Cr and Ni can fall below 0.5%. So the sludge in the rear part can be used as fluorgypsum or fluorite. Meanwhile,the results of the analysis on heavy metals leaching toxicity and morphologic distribution indicate that the two kinds of sectionalized sludge are not classified as hazardous wastes, which have a stable behavior and better utilization values compared with the former mixed- sludge.展开更多
The photovoltaic module building integration level affects the module temperature and,consequently,its output power.In this work,a methodology has been proposed to estimate the influence of the level of architectural ...The photovoltaic module building integration level affects the module temperature and,consequently,its output power.In this work,a methodology has been proposed to estimate the influence of the level of architectural photovoltaic integration on the photovoltaic energy balance with natural ventilation or with forced cooling systems.The developed methodology is applied for five photovoltaic module technologies(m⁃Si,p⁃Si,a⁃Si,CdTe,and CIGS)on four characteristic locations(Athens,Davos,Stockholm,and Würzburg).To this end,a photovoltaic module thermal radiation parameter,PVj,is introduced in the characterization of the PV module technology,rendering the correlations suitable for building⁃integrated photovoltaic(BIPV)applications,with natural ventilation or with forced cooling systems.The results show that PVj has a significant influence on the energy balances,according to the architectural photovoltaic integration and climatic conditions.Keywords:Photovoltaic cooling;BIPV;Photovoltaic;Ventilation;Photovoltaic integration level in building【OA】(2)Graph⁃Based methodology for Multi⁃Scale generation of energy analysis models from IFC,by Asier Mediavilla,Peru Elguezabal,Natalia Lasarte,Article 112795 Abstract:Process digitalisation and automation is unstoppable in all industries,including construction.However,its widespread adoption,even for non⁃experts,demands easy⁃to⁃use tools that reduce technical requirements.BIM to BEM(Building Energy Models)workflows are a clear example,where ad⁃hoc prepared models are needed.This paper describes a methodology,based on graph techniques,to automate it by highly reducing the input BIM requirements found in similar approaches,being applicable to almost any IFC.This is especially relevant in retrofitting,where reality capture tools(e.g.,3D laser scanning,object recognition in drawings)are prone to create geometry clashes and other inconsistencies,posing higher challenges for automation.Another innovation presented is its multi⁃scale nature,efficiently addressing the surroundings impact in the energy model.The application to selected test cases has been successful and further tests are ongoing,considering a higher variety of BIM models in relation to tools and techniques used and model sizes.展开更多
The degradation process modeling is one of research hotspots of prognostic and health management(PHM),which can be used to estimate system reliability and remaining useful life(RUL).In order to study system degradatio...The degradation process modeling is one of research hotspots of prognostic and health management(PHM),which can be used to estimate system reliability and remaining useful life(RUL).In order to study system degradation process,cumulative damage model is used for degradation modeling.Assuming that damage increment is Gamma distribution,shock counting subjects to a homogeneous Poisson process(HPP)when degradation process is linear,and shock counting is a non-homogeneous Poisson process(NHPP)when degradation process is nonlinear.A two-stage degradation system is considered in this paper,for which the degradation process is linear in the first stage and the degradation process is nonlinear in the second stage.A nonlinear modeling method for considered system is put forward,and reliability model and remaining useful life model are established.A case study is given to validate the veracities of established models.展开更多
Cloud Computing as a disruptive technology, provides a dynamic, elastic and promising computing climate to tackle the challenges of big data processing and analytics. Hadoop and MapReduce are the widely used open sour...Cloud Computing as a disruptive technology, provides a dynamic, elastic and promising computing climate to tackle the challenges of big data processing and analytics. Hadoop and MapReduce are the widely used open source frameworks in Cloud Computing for storing and processing big data in the scalable fashion. Spark is the latest parallel computing engine working together with Hadoop that exceeds MapReduce performance via its in-memory computing and high level programming features. In this paper, we present our design and implementation of a productive, domain-specific big data analytics cloud platform on top of Hadoop and Spark. To increase user’s productivity, we created a variety of data processing templates to simplify the programming efforts. We have conducted experiments for its productivity and performance with a few basic but representative data processing algorithms in the petroleum industry. Geophysicists can use the platform to productively design and implement scalable seismic data processing algorithms without handling the details of data management and the complexity of parallelism. The Cloud platform generates a complete data processing application based on user’s kernel program and simple configurations, allocates resources and executes it in parallel on top of Spark and Hadoop.展开更多
The suitable process parameters for a two-stage turbo air classifier are important for obtaining the ultrafine powder that has a narrow particle-size distribution, however little has been published internationally on ...The suitable process parameters for a two-stage turbo air classifier are important for obtaining the ultrafine powder that has a narrow particle-size distribution, however little has been published internationally on the classification process for the two-stage turbo air classifier in series. The influence of the process parameters of a two-stage turbo air classifier in series on classification performance is empirically studied by using aluminum oxide powders as the experimental material. The experimental results show the following: 1) When the rotor cage rotary speed of the first-stage classifier is increased from 2 300 r/min to 2 500 r/min with a constant rotor cage rotary speed of the second-stage classifier, classification precision is increased from 0.64 to 0.67. However, in this case, the final ultrafine powder yield is decreased from 79% to 74%, which means the classification precision and the final ultrafine powder yield can be regulated through adjusting the rotor cage rotary speed of the first-stage classifier. 2) When the rotor cage rotary speed of the second-stage classifier is increased from 2 500 r/min to 3 100 r/min with a constant rotor cage rotary speed of the first-stage classifier, the cut size is decreased from 13.16 μm to 8.76 μm, which means the cut size of the ultrafine powder can be regulated through adjusting the rotor cage rotary speed of the second-stage classifier. 3) When the feeding speed is increased from 35 kg/h to 50 kg/h, the 'fish-hook' effect is strengthened, which makes the ultrafine powder yield decrease. 4) To weaken the 'fish-hook' effect, the equalization of the two-stage wind speeds or the combination of a high first-stage wind speed with a low second-stage wind speed should be selected. This empirical study provides a criterion of process parameter configurations for a two-stage or multi-stage classifier in series, which offers a theoretical basis for practical production.展开更多
Sustainable building in China has gained attention both domestically and abroad. Despite the fast increase in sustainable assessment tools developed locally or adopted from overseas, there are still criticisms about t...Sustainable building in China has gained attention both domestically and abroad. Despite the fast increase in sustainable assessment tools developed locally or adopted from overseas, there are still criticisms about the current situation of weak implementation and lack of comprehensive consideration. The lack of consideration of economic and social aspects or building performance on whole building life cycle all lead to departure from the true meaning of sustainable development. And lack of participation on the part of stakeholders makes it too theoretical to be carried out. This research aims to develop a model to address this problem. This research started with review of current sustainable assessment tools applied in China. As the assessment indicators have clear regional disparities, and almost no current tool considers all three pillars of environmental, economic and social in building life cycle. An industry survey was therefore designed for generation of indicators at different building stages, and personal interviews relevant to different occupation in building industry were conducted to complement the questionnaire survey. After that, the model Building Sustainable Score (BSS) was developed based on the stakeholders’ participation. Finally, the model is verified by a case study.展开更多
A two-stage vacuum pressure swing adsorption(VPSA)process that coupled kinetically controlled and equilibrium controlled separation process with reflux has been investigated for capturing carbon dioxide from dry flue ...A two-stage vacuum pressure swing adsorption(VPSA)process that coupled kinetically controlled and equilibrium controlled separation process with reflux has been investigated for capturing carbon dioxide from dry flue gas(85%N_(2)/15%CO_(2)).In the first enriching stage,carbon molecular sieve(CMS),which shows kinetic selectivity for CO_(2)/N_(2),is adopted as the adsorbent to remove most N_(2)in feed gas,thereby upgrading CO_(2)and significantly reducing the amount for further refinement.The second stage loads zeolite 13X as adsorbent to purify the CO_(2)-rich flow from the first stage for meeting the requirements of National Energy Technology Laboratory.Series of experiments have been conducted for adsorption isotherms measuring and lab-scale experimental validation as well as analysis.The effect of feed composition on the separation performance of the PSA system was studied experimentally and theoretically here.The optimal results achieved 95.1%purity and 92.9%recovery with a high CO_(2)productivity(1.89 mol CO_(2)·h^(-1)·kg^(-1))and an appropriate energy consumption of 1.07 MJ·(kg CO_(2))^(-1).Further analysis has been carried out by simulation for explicating the temperature,pressure,and concentration distribution at cyclic steady state.展开更多
As the non-periodic inspections are common in practice,a two-stage inspection model based on a three-stage failure process is proposed. The two-stage inspection means that the system is inspected with the first inspec...As the non-periodic inspections are common in practice,a two-stage inspection model based on a three-stage failure process is proposed. The two-stage inspection means that the system is inspected with the first inspection interval T_1 and the second inspection interval T_2. Because of the three color schemes commonly used in industry,three stages are divided by the system lifetime:normal, minor defective and severe defective stages. Upon the failure of the system,replacement is carried out. Maintenance is done once identifying the severe defective stage. However,when the minor defective stage is identified by the second inspection interval T_2,action of halving the subsequent inspection interval is adopted.Otherwise,no action is required. Our objective function is to optimize the inspection intervals so as to minimize the expected cost per unit time. Finally,a numerical example is presented to illustrate the effectiveness of the proposed model.展开更多
The pervasive diffusion of digital technologies opened up to new concepts in managing and monitoring the processes occurring in our society.Information and Communication Technologies(ICTs)become enabling tools to reth...The pervasive diffusion of digital technologies opened up to new concepts in managing and monitoring the processes occurring in our society.Information and Communication Technologies(ICTs)become enabling tools to rethink our way of living,consuming and producing goods and services.Among these,the Internet of Things(IoT)represents the disruptive technology that may redefine the stages of the building process to meet renewed environmental challenges.This new technological paradigm imports in the Architecture,Engineering and Construction(AEC)sector new and not-tectonic instances.In this context,the paper maps the experiences related to the use of IoT for managing the building process.Through a systematic literature review,the article highlights the potential benefits generable by a widespread integration of IoT in the AEC sector.In particular,the article has three purposes:defining the IoT infrastructure for its proper application in the AEC sector;identifying IoT main application domains;investigating the integration modalities.展开更多
When deciding on the best historic building retrofit,energy savings and thermal comfort can be quantitatively evaluated using an energy model,whereas conservation compatibility is intrinsically qualitative and reflect...When deciding on the best historic building retrofit,energy savings and thermal comfort can be quantitatively evaluated using an energy model,whereas conservation compatibility is intrinsically qualitative and reflects the perspective of the local heritage authority. We present a methodology that permits finding and comparing optimal retrofits for historic buildings in a multi-perspective and quantitative way. We use an analytic hierarchyprocess to quantify conservation compatibility by distilling a conservation score from the opinions of 10 experts in the field. This score,along with energy needs for heating and cooling and thermal comfort,are the three targets of a multi-objective optimization aimed at identifying optimal retrofits for a medieval building in the north of Italy,destined to become a museum. Retrofit measures considered were different kinds of external and internal envelope insulation,improvement of airtightness,replacement of windows,and ventilative cooling. The result is a portfolio of optimal retrofits that cover the whole range of conservation compatibility. We showthat in the analyzed case heritage preservation is compatible with a four-fold reduction in energy needs at a high thermal comfort level. Even higher energy savings are only achievable at the cost of heritage degradation.展开更多
Assessment standard for green store building of national standard has been compiled. The index has been given by experts' subjective assignment based on experience. Analytic hierarchy process has been used,making ...Assessment standard for green store building of national standard has been compiled. The index has been given by experts' subjective assignment based on experience. Analytic hierarchy process has been used,making questionnaires of experts,using pairwise comparison and calculating the weight of each index. The weight of index in assessment would not only make quantitative evaluation on the whole situation of green store buildings,but also provide the foundation for compilation and revision.展开更多
In this research, effect of varying spatial orientations on the build time requirements for fused deposition modelling process is studied. Constructive solid geometry cylindrical primitive is taken as work piece and m...In this research, effect of varying spatial orientations on the build time requirements for fused deposition modelling process is studied. Constructive solid geometry cylindrical primitive is taken as work piece and modeling is accomplished for it. Response surface methodology is used to design the experiments and obtain statistical models for build time requirements corresponding to different orientations of the given primitive in modeller build volume. Contour width, air gap, slice height, raster width, raster angle and angle of orientation are treated as process parameters. Percentage contribution of individual process parameter is found to change for build time corresponding to different spatial orientations. Also, the average of build time requirement changes with spatial orientation. This paper attempts to clearly discuss and describe the observations with an aim to develop a clear understanding of effect of spatial variations on the build time for Fused Deposition Modelling process. This work is an integral part of process layout optimization and these results can effectively aid designers specially while tackling nesting issues.展开更多
The necessity of having an effective computer-aided decision support system in the housing construction industry is rapidly growing alongside the demand for green buildings and green building products. Identifying and...The necessity of having an effective computer-aided decision support system in the housing construction industry is rapidly growing alongside the demand for green buildings and green building products. Identifying and defining financially viable low-cost green building materials and components, just like selecting them, is a crucial exercise in subjectivity. With so many variables to consider, the task of evaluating such products can be complex and discouraging. Moreover, the existing mode for selecting and managing, often very large information associated with their impacts constrains decision-makers to perform a trade-off analysis that does not necessarily guarantee the most environmentally preferable material. This paper introduces the development of a multi-criteria decision support system (DSS) aimed at improving the understanding of the principles of best practices associated with the impacts of low-cost green building materials and components. The DSS presented in this paper is to provide designers with useful and explicit information that will aid informed decision-making in their choice of materials for low-cost green residential housing projects. The prototype MSDSS is developed using macro-in-excel, which is a fairly recent database management technique used for integrating data from multiple, often very large databases and other information sources. This model consists of a database to store different types of low-cost green materials with their corresponding attributes and performance characteristics. The DSS design is illustrated with particular emphasis on the development of the material selection data schema, and application of the Analytical Hierarchy Process (AHP) concept to a material selection problem. Details of the MSDSS model are also discussed including workflow of the data evaluation process. The prototype model has been developed with inputs elicited from domain experts and extensive literature review, and refined with feedback obtained from selected expert builder and developer companies. This paper further demonstrates the application of the prototype MSDSS for selecting the most appropriate low-cost green building material from among a list of several available options, and finally concludes the study with the associated potential benefits of the model to research and practice.展开更多
Analytic hierarchy process(Group AHP) is combined with two different methods of assigning experts' priority to weight indicators in building energy efficiency assessment.One is to assign the experts' priority ...Analytic hierarchy process(Group AHP) is combined with two different methods of assigning experts' priority to weight indicators in building energy efficiency assessment.One is to assign the experts' priority averagely,and the other is to use cluster analysis to assign experts' priority.The results show that,1) Different expert's priority assigns result in great different weights of indicators in building energy efficiency assessment,therefore,the method of assigning experts' priority should be taken into account carefully while weighting indicators of building energy efficiency assessment using Group AHP;2) Three indicators are found to be overwhelmingly important in residential building energy efficiency assessment in the hot summer and cold winter zone in China.They are 'Outdoor & indoor shadow','Heating & air-conditioning facilities' and 'Insulation of envelope';3) The method combining cluster analysis with Group AHP to weight indicator of building energy efficiency assessment has the advantage of finding overwhelming important indicator,whereas,some less important indicators have a tendency to be ignored.A useful reference is provided for building energy conservation including policy revision and energy efficient residential building design.展开更多
In recent years, flash flood disasters have occurred frequently in southwest China due to the increased frequency of extreme climate events. To solve this problem, great efforts have been made in studying the process ...In recent years, flash flood disasters have occurred frequently in southwest China due to the increased frequency of extreme climate events. To solve this problem, great efforts have been made in studying the process of flash flood. However, little attention was paid on bearing body of hazard, the clusters of buildings. Thus the real disaster mechanism of flash flood remains unclear.Accordingly, based on the experiments of artificial flash floods in a conceptual solid model, this paper focuses on the flood-impacted inundation characteristics of the building clusters at different locations of the gully model, in order to obtain a better understanding of the disaster process and the interaction between the flash floods and building clusters. The results showed that, in a typical smallscale flash flood gully with hot and dry climate, 1)clusters of buildings on an alluvial fan could reduce about 35% of the flooding area by blocking the diffusion of the flood to the depression areas, and could also promote the deposition in lower reaches of the river channel by blocking the overbank flow from going back into the channel, making the width-depth ratio of the channel larger. 2) The flash flood rates of disaster and hazard on the alluvial fan are generally higher than that of the inner gully. For the inner gully,buildings located on the beaches along the lower river and the transitional areas of the straight channel and channel bends can easily be affected because of their lower elevations. For the alluvial fan, buildings nearby the meanders suffer the greatest impacts because of bank collapsing and flooding. 3) The safe vertical distance from a building to the river channel is 13 m for the buildings in the inner gully under extreme floods. Below this threshold, the smaller the vertical distance is, the greater the risk exposure is. For the buildings on the alluvial fan, especially for the buildings near the concave bank of the top rush point,the horizontal distance is more important, and the safe value is 80 m under extreme floods.展开更多
基金partially supported by the Strategic Priority Research Program of Chinese Academy of Science(No.XDB 34030000)the National Natural Science Foundation of China(Nos.11975293 and 12205348)。
文摘The High-energy Fragment Separator(HFRS),which is currently under construction,is a leading international radioactive beam device.Multiple sets of position-sensitive twin time projection chamber(TPC)detectors are distributed on HFRS for particle identification and beam monitoring.The twin TPCs'readout electronics system operates in a trigger-less mode due to its high counting rate,leading to a challenge of handling large amounts of data.To address this problem,we introduced an event-building algorithm.This algorithm employs a hierarchical processing strategy to compress data during transmission and aggregation.In addition,it reconstructs twin TPCs'events online and stores only the reconstructed particle information,which significantly reduces the burden on data transmission and storage resources.Simulation studies demonstrated that the algorithm accurately matches twin TPCs'events and reduces more than 98%of the data volume at a counting rate of 500 kHz/channel.
基金funded by the NationalNatural Science Foundation of China (Nos.11902229,11502181)the Strategic Priority Research Program of the Chinese Academy of Sciences (Grant Nos.XDB22040502,XDC06030200).
文摘The comprehensive tire building and shaping processes are investigated through the finite element method(FEM)in this article.The mechanical properties of the uncured rubber from different tire components are investigated through cyclic loading-unloading experiments under different strain rates.Based on the experiments,an elastoviscoplastic constitutive model is adopted to describe themechanical behaviors of the uncured rubber.The distinct mechanical properties,including the stress level,hysteresis and residual strain,of the uncured rubber can all be well characterized.The whole tire building process(including component winding,rubber bladder inflation,component stitching and carcass band folding-back)and the shaping process are simulated using this constitutive model.The simulated green tire profile is in good agreement with the actual profile obtained through 3D scanning.The deformation and stress of the rubber components and the cord reinforcements during production can be obtained fromthe FE simulation,which is helpful for judging the rationality of the tire construction design.Finally,the influence of the parameter“drum width”is investigated,and the simulated result is found to be consistent with the experimental observations,which verifies the effectiveness of the simulation.The established simulation strategy provides some guiding significance for the improvement of tire design parameters and the elimination of tire production defects.
文摘Urbanization has led to the rapid development of the construction industry.However,this has also led to higher requirements for the construction engineering management.Other than the quality monitoring of engineering construction,the energy-saving properties of the building should also be considered.Therefore,a scientific management approach should be adopted to improve green building management.This paper primarily examines the importance of quality management in green building construction,along with the factors influencing it.It also identifies the quality issues present in current green building construction.Finally,it proposes measures for quality management in the green building construction process to facilitate the industry’s healthy development.
基金supported by the National Natural Science Foundation of China (31701527)the National Key Research and Development Program of China (2017YFD0400401)+1 种基金the Policy Guidance Program of Jiangsu Province, China (SZ-SQ2017021)the Jiangsu Province “Collaborative Innovation Center of Food Safety and Quality Control” industry development program, China。
文摘The two-stage dough mixing process was innovated to improve the qualities of bread made from potato flour(PF) and wheat flour at a ratio of 1:1(w/w). The final dough was first prepared from wheat flour before being added with PF. The effects of the method on enhancing the dough qualities were verified, and the distribution of water in gluten-gelatinized starch matrix of the doughs was investigated. We observed that the bread qualities were improved, as reflected by the increase of specific volume from 2.26 to 2.96 m L g^–1 and the decrease of crumb hardness from 417.93 to 255.57 g. The results from rheofermentometric measurements showed that the dough mixed using the developed mixing method had higher maximum dough height value, time of dough porosity appearance, and gas retention coefficient, as well as enhanced gluten matrix formation compared to that mixed by the traditional mixing method. The results from low-field nuclear magnetic resonance confirmed that the competitive water absorption between gluten and gelatinized starch could restrict the formation of gluten network in the dough mixed using the traditional mixing process. Using the novel mixing method, gluten could be sufficiently hydrated in stage 1, which could then weaken the competitive water absorption caused by gelatinized starch in stage 2;this could also be indicated by the greater mobility of proton in PF and better development of gluten network during mixing.
基金supported by the National Natural Science Foundation of China (No. 51338006)
文摘As an important element in sustainable building design, the building envelope has been witnessing a constant shift in the design approach. Integrating multi-objective optimization(MOO) into the building envelope design process is very promising, but not easy to realize in an actual project due to several factors, including the complexity of optimization model construction, lack of a dynamic-visualization capacity in the simulation tools and consideration of how to match the optimization with the actual design process. To overcome these difficulties, this study constructed an integrated building envelope design process(IBEDP) based on parametric modelling, which was implemented using Grasshopper platform and interfaces to control the simulation software and optimization algorithm. A railway station was selected as a case study for applying the proposed IBEDP, which also utilized a grid-based variable design approach to achieve flexible optimum fenestrations. To facilitate the stepwise design process, a novel strategy was proposed with a two-step optimization, which optimized various categories of variables separately. Compared with a one-step optimization,though the proposed strategy performed poorly in the diversity of solutions, the quantitative assessment of the qualities of Pareto-optimum solution sets illustrates that it is superior.
文摘Based on the characteristics of pickling wastewater in the cold-rolling production of stainless steel, a new processing route, featuring source sludge reduction, wastewater two-stage treatment, heavy metal-contained sludge and calcium salt sludge separating recovery, was proposed. As shown by the research results, after the two-stage process treatment, the effluent water can steadily reach the emission standards, the sludge yield can be decreased by more than 8% ; within the heavy metal-contained sludge, the recovery rates of Fc,Cr and Ni can either reach or surpass 95% ,and the total content ofF and S can drop to around 3%. Therefore,the sludge in the front part can be used as ferric dust. In the calcium salt sludge ,the recovery rate of F can either reach or surpass 85% ,and the total contents of Fe,Cr and Ni can fall below 0.5%. So the sludge in the rear part can be used as fluorgypsum or fluorite. Meanwhile,the results of the analysis on heavy metals leaching toxicity and morphologic distribution indicate that the two kinds of sectionalized sludge are not classified as hazardous wastes, which have a stable behavior and better utilization values compared with the former mixed- sludge.
文摘The photovoltaic module building integration level affects the module temperature and,consequently,its output power.In this work,a methodology has been proposed to estimate the influence of the level of architectural photovoltaic integration on the photovoltaic energy balance with natural ventilation or with forced cooling systems.The developed methodology is applied for five photovoltaic module technologies(m⁃Si,p⁃Si,a⁃Si,CdTe,and CIGS)on four characteristic locations(Athens,Davos,Stockholm,and Würzburg).To this end,a photovoltaic module thermal radiation parameter,PVj,is introduced in the characterization of the PV module technology,rendering the correlations suitable for building⁃integrated photovoltaic(BIPV)applications,with natural ventilation or with forced cooling systems.The results show that PVj has a significant influence on the energy balances,according to the architectural photovoltaic integration and climatic conditions.Keywords:Photovoltaic cooling;BIPV;Photovoltaic;Ventilation;Photovoltaic integration level in building【OA】(2)Graph⁃Based methodology for Multi⁃Scale generation of energy analysis models from IFC,by Asier Mediavilla,Peru Elguezabal,Natalia Lasarte,Article 112795 Abstract:Process digitalisation and automation is unstoppable in all industries,including construction.However,its widespread adoption,even for non⁃experts,demands easy⁃to⁃use tools that reduce technical requirements.BIM to BEM(Building Energy Models)workflows are a clear example,where ad⁃hoc prepared models are needed.This paper describes a methodology,based on graph techniques,to automate it by highly reducing the input BIM requirements found in similar approaches,being applicable to almost any IFC.This is especially relevant in retrofitting,where reality capture tools(e.g.,3D laser scanning,object recognition in drawings)are prone to create geometry clashes and other inconsistencies,posing higher challenges for automation.Another innovation presented is its multi⁃scale nature,efficiently addressing the surroundings impact in the energy model.The application to selected test cases has been successful and further tests are ongoing,considering a higher variety of BIM models in relation to tools and techniques used and model sizes.
基金National Outstanding Youth Science Fund Project,China(No.71401173)
文摘The degradation process modeling is one of research hotspots of prognostic and health management(PHM),which can be used to estimate system reliability and remaining useful life(RUL).In order to study system degradation process,cumulative damage model is used for degradation modeling.Assuming that damage increment is Gamma distribution,shock counting subjects to a homogeneous Poisson process(HPP)when degradation process is linear,and shock counting is a non-homogeneous Poisson process(NHPP)when degradation process is nonlinear.A two-stage degradation system is considered in this paper,for which the degradation process is linear in the first stage and the degradation process is nonlinear in the second stage.A nonlinear modeling method for considered system is put forward,and reliability model and remaining useful life model are established.A case study is given to validate the veracities of established models.
文摘Cloud Computing as a disruptive technology, provides a dynamic, elastic and promising computing climate to tackle the challenges of big data processing and analytics. Hadoop and MapReduce are the widely used open source frameworks in Cloud Computing for storing and processing big data in the scalable fashion. Spark is the latest parallel computing engine working together with Hadoop that exceeds MapReduce performance via its in-memory computing and high level programming features. In this paper, we present our design and implementation of a productive, domain-specific big data analytics cloud platform on top of Hadoop and Spark. To increase user’s productivity, we created a variety of data processing templates to simplify the programming efforts. We have conducted experiments for its productivity and performance with a few basic but representative data processing algorithms in the petroleum industry. Geophysicists can use the platform to productively design and implement scalable seismic data processing algorithms without handling the details of data management and the complexity of parallelism. The Cloud platform generates a complete data processing application based on user’s kernel program and simple configurations, allocates resources and executes it in parallel on top of Spark and Hadoop.
基金supported by National Natural Science Foundation of China (Grant Nos. 51074012, 51204009)
文摘The suitable process parameters for a two-stage turbo air classifier are important for obtaining the ultrafine powder that has a narrow particle-size distribution, however little has been published internationally on the classification process for the two-stage turbo air classifier in series. The influence of the process parameters of a two-stage turbo air classifier in series on classification performance is empirically studied by using aluminum oxide powders as the experimental material. The experimental results show the following: 1) When the rotor cage rotary speed of the first-stage classifier is increased from 2 300 r/min to 2 500 r/min with a constant rotor cage rotary speed of the second-stage classifier, classification precision is increased from 0.64 to 0.67. However, in this case, the final ultrafine powder yield is decreased from 79% to 74%, which means the classification precision and the final ultrafine powder yield can be regulated through adjusting the rotor cage rotary speed of the first-stage classifier. 2) When the rotor cage rotary speed of the second-stage classifier is increased from 2 500 r/min to 3 100 r/min with a constant rotor cage rotary speed of the first-stage classifier, the cut size is decreased from 13.16 μm to 8.76 μm, which means the cut size of the ultrafine powder can be regulated through adjusting the rotor cage rotary speed of the second-stage classifier. 3) When the feeding speed is increased from 35 kg/h to 50 kg/h, the 'fish-hook' effect is strengthened, which makes the ultrafine powder yield decrease. 4) To weaken the 'fish-hook' effect, the equalization of the two-stage wind speeds or the combination of a high first-stage wind speed with a low second-stage wind speed should be selected. This empirical study provides a criterion of process parameter configurations for a two-stage or multi-stage classifier in series, which offers a theoretical basis for practical production.
文摘Sustainable building in China has gained attention both domestically and abroad. Despite the fast increase in sustainable assessment tools developed locally or adopted from overseas, there are still criticisms about the current situation of weak implementation and lack of comprehensive consideration. The lack of consideration of economic and social aspects or building performance on whole building life cycle all lead to departure from the true meaning of sustainable development. And lack of participation on the part of stakeholders makes it too theoretical to be carried out. This research aims to develop a model to address this problem. This research started with review of current sustainable assessment tools applied in China. As the assessment indicators have clear regional disparities, and almost no current tool considers all three pillars of environmental, economic and social in building life cycle. An industry survey was therefore designed for generation of indicators at different building stages, and personal interviews relevant to different occupation in building industry were conducted to complement the questionnaire survey. After that, the model Building Sustainable Score (BSS) was developed based on the stakeholders’ participation. Finally, the model is verified by a case study.
基金financially supported by the Renewable Energy and Hydrogen Projects National Key Research&Development Program of China(2019YFB1505000)。
文摘A two-stage vacuum pressure swing adsorption(VPSA)process that coupled kinetically controlled and equilibrium controlled separation process with reflux has been investigated for capturing carbon dioxide from dry flue gas(85%N_(2)/15%CO_(2)).In the first enriching stage,carbon molecular sieve(CMS),which shows kinetic selectivity for CO_(2)/N_(2),is adopted as the adsorbent to remove most N_(2)in feed gas,thereby upgrading CO_(2)and significantly reducing the amount for further refinement.The second stage loads zeolite 13X as adsorbent to purify the CO_(2)-rich flow from the first stage for meeting the requirements of National Energy Technology Laboratory.Series of experiments have been conducted for adsorption isotherms measuring and lab-scale experimental validation as well as analysis.The effect of feed composition on the separation performance of the PSA system was studied experimentally and theoretically here.The optimal results achieved 95.1%purity and 92.9%recovery with a high CO_(2)productivity(1.89 mol CO_(2)·h^(-1)·kg^(-1))and an appropriate energy consumption of 1.07 MJ·(kg CO_(2))^(-1).Further analysis has been carried out by simulation for explicating the temperature,pressure,and concentration distribution at cyclic steady state.
文摘As the non-periodic inspections are common in practice,a two-stage inspection model based on a three-stage failure process is proposed. The two-stage inspection means that the system is inspected with the first inspection interval T_1 and the second inspection interval T_2. Because of the three color schemes commonly used in industry,three stages are divided by the system lifetime:normal, minor defective and severe defective stages. Upon the failure of the system,replacement is carried out. Maintenance is done once identifying the severe defective stage. However,when the minor defective stage is identified by the second inspection interval T_2,action of halving the subsequent inspection interval is adopted.Otherwise,no action is required. Our objective function is to optimize the inspection intervals so as to minimize the expected cost per unit time. Finally,a numerical example is presented to illustrate the effectiveness of the proposed model.
文摘The pervasive diffusion of digital technologies opened up to new concepts in managing and monitoring the processes occurring in our society.Information and Communication Technologies(ICTs)become enabling tools to rethink our way of living,consuming and producing goods and services.Among these,the Internet of Things(IoT)represents the disruptive technology that may redefine the stages of the building process to meet renewed environmental challenges.This new technological paradigm imports in the Architecture,Engineering and Construction(AEC)sector new and not-tectonic instances.In this context,the paper maps the experiences related to the use of IoT for managing the building process.Through a systematic literature review,the article highlights the potential benefits generable by a widespread integration of IoT in the AEC sector.In particular,the article has three purposes:defining the IoT infrastructure for its proper application in the AEC sector;identifying IoT main application domains;investigating the integration modalities.
文摘When deciding on the best historic building retrofit,energy savings and thermal comfort can be quantitatively evaluated using an energy model,whereas conservation compatibility is intrinsically qualitative and reflects the perspective of the local heritage authority. We present a methodology that permits finding and comparing optimal retrofits for historic buildings in a multi-perspective and quantitative way. We use an analytic hierarchyprocess to quantify conservation compatibility by distilling a conservation score from the opinions of 10 experts in the field. This score,along with energy needs for heating and cooling and thermal comfort,are the three targets of a multi-objective optimization aimed at identifying optimal retrofits for a medieval building in the north of Italy,destined to become a museum. Retrofit measures considered were different kinds of external and internal envelope insulation,improvement of airtightness,replacement of windows,and ventilative cooling. The result is a portfolio of optimal retrofits that cover the whole range of conservation compatibility. We showthat in the analyzed case heritage preservation is compatible with a four-fold reduction in energy needs at a high thermal comfort level. Even higher energy savings are only achievable at the cost of heritage degradation.
基金Sponsored by the National Project of Scientific and Technical Supporting Programs of Ministry of Science & Technology of China(Grant No.2012BAJ10B02)
文摘Assessment standard for green store building of national standard has been compiled. The index has been given by experts' subjective assignment based on experience. Analytic hierarchy process has been used,making questionnaires of experts,using pairwise comparison and calculating the weight of each index. The weight of index in assessment would not only make quantitative evaluation on the whole situation of green store buildings,but also provide the foundation for compilation and revision.
文摘In this research, effect of varying spatial orientations on the build time requirements for fused deposition modelling process is studied. Constructive solid geometry cylindrical primitive is taken as work piece and modeling is accomplished for it. Response surface methodology is used to design the experiments and obtain statistical models for build time requirements corresponding to different orientations of the given primitive in modeller build volume. Contour width, air gap, slice height, raster width, raster angle and angle of orientation are treated as process parameters. Percentage contribution of individual process parameter is found to change for build time corresponding to different spatial orientations. Also, the average of build time requirement changes with spatial orientation. This paper attempts to clearly discuss and describe the observations with an aim to develop a clear understanding of effect of spatial variations on the build time for Fused Deposition Modelling process. This work is an integral part of process layout optimization and these results can effectively aid designers specially while tackling nesting issues.
文摘The necessity of having an effective computer-aided decision support system in the housing construction industry is rapidly growing alongside the demand for green buildings and green building products. Identifying and defining financially viable low-cost green building materials and components, just like selecting them, is a crucial exercise in subjectivity. With so many variables to consider, the task of evaluating such products can be complex and discouraging. Moreover, the existing mode for selecting and managing, often very large information associated with their impacts constrains decision-makers to perform a trade-off analysis that does not necessarily guarantee the most environmentally preferable material. This paper introduces the development of a multi-criteria decision support system (DSS) aimed at improving the understanding of the principles of best practices associated with the impacts of low-cost green building materials and components. The DSS presented in this paper is to provide designers with useful and explicit information that will aid informed decision-making in their choice of materials for low-cost green residential housing projects. The prototype MSDSS is developed using macro-in-excel, which is a fairly recent database management technique used for integrating data from multiple, often very large databases and other information sources. This model consists of a database to store different types of low-cost green materials with their corresponding attributes and performance characteristics. The DSS design is illustrated with particular emphasis on the development of the material selection data schema, and application of the Analytical Hierarchy Process (AHP) concept to a material selection problem. Details of the MSDSS model are also discussed including workflow of the data evaluation process. The prototype model has been developed with inputs elicited from domain experts and extensive literature review, and refined with feedback obtained from selected expert builder and developer companies. This paper further demonstrates the application of the prototype MSDSS for selecting the most appropriate low-cost green building material from among a list of several available options, and finally concludes the study with the associated potential benefits of the model to research and practice.
基金Project(2010R10036) supported by the Science and Technology Department of Zhejiang Province, China
文摘Analytic hierarchy process(Group AHP) is combined with two different methods of assigning experts' priority to weight indicators in building energy efficiency assessment.One is to assign the experts' priority averagely,and the other is to use cluster analysis to assign experts' priority.The results show that,1) Different expert's priority assigns result in great different weights of indicators in building energy efficiency assessment,therefore,the method of assigning experts' priority should be taken into account carefully while weighting indicators of building energy efficiency assessment using Group AHP;2) Three indicators are found to be overwhelmingly important in residential building energy efficiency assessment in the hot summer and cold winter zone in China.They are 'Outdoor & indoor shadow','Heating & air-conditioning facilities' and 'Insulation of envelope';3) The method combining cluster analysis with Group AHP to weight indicator of building energy efficiency assessment has the advantage of finding overwhelming important indicator,whereas,some less important indicators have a tendency to be ignored.A useful reference is provided for building energy conservation including policy revision and energy efficient residential building design.
基金supported by the Specific Research of China Institute of Water Resources and Hydropower Research (Grant Nos. Fangji 1240)Chinese Ministry of Water Resources (Grant Nos. 201301058 and 20131059)the Basic Research Fund for Central Public Research Institutes (Grant No. CKSF2015010/TB)
文摘In recent years, flash flood disasters have occurred frequently in southwest China due to the increased frequency of extreme climate events. To solve this problem, great efforts have been made in studying the process of flash flood. However, little attention was paid on bearing body of hazard, the clusters of buildings. Thus the real disaster mechanism of flash flood remains unclear.Accordingly, based on the experiments of artificial flash floods in a conceptual solid model, this paper focuses on the flood-impacted inundation characteristics of the building clusters at different locations of the gully model, in order to obtain a better understanding of the disaster process and the interaction between the flash floods and building clusters. The results showed that, in a typical smallscale flash flood gully with hot and dry climate, 1)clusters of buildings on an alluvial fan could reduce about 35% of the flooding area by blocking the diffusion of the flood to the depression areas, and could also promote the deposition in lower reaches of the river channel by blocking the overbank flow from going back into the channel, making the width-depth ratio of the channel larger. 2) The flash flood rates of disaster and hazard on the alluvial fan are generally higher than that of the inner gully. For the inner gully,buildings located on the beaches along the lower river and the transitional areas of the straight channel and channel bends can easily be affected because of their lower elevations. For the alluvial fan, buildings nearby the meanders suffer the greatest impacts because of bank collapsing and flooding. 3) The safe vertical distance from a building to the river channel is 13 m for the buildings in the inner gully under extreme floods. Below this threshold, the smaller the vertical distance is, the greater the risk exposure is. For the buildings on the alluvial fan, especially for the buildings near the concave bank of the top rush point,the horizontal distance is more important, and the safe value is 80 m under extreme floods.