Structures of ceramics coatings on steel fabricated by hot-dipping and micro-arc oxidation

Firstly, an aluminum coating was produced metallurgically on mild steel by hot-dipping, then an aluminum oxide coating was formed self-growingly from the aluminum coating by micro-arc oxidation treatment. The structures of the composite coatings were investigated by means of SEM, TEM and XRD. The results show that the composite coating consists of three layers which are Fe-Al alloy, aluminum coating and aluminum oxide orderly outward from the steel substrate. There are amorphous phases, k-Al2O3 and θ-Al2O3 mainly in the aluminum oxide.

Preparation of tetrapod-like ZnO whiskers from waste hot dipping zinc

Large and uniform tetrapod-like ZnO whiskers （T-ZnO） were prepared from waste hot dipping zinc by vapor oxidation and examined by means of X-ray diffraction and ICP-AES analysis and scanning electron microscope. The products are pure hexagonal wurtzite crystals with tetrapod shape and edge size of center body 56 μm and needle length of 100130 μm. The size and shape of ZnO particles are fully controlled by the growth conditions and T-ZnO can be obtained only at 8501 000 ℃ and total gas flow rate ranging from 40 to 250 L·h-1 in which the size of the T-ZnO particles varies slightly with temperature. The process of the formation of T-ZnO is that T-ZnO may nucleate at the initial stage with a complete tetrapod shape and develop to the large size, but not the process of （preferential） growth of octahedral nuclei and subsequent growth of the needles. The experiment presents a new method to prepare T-ZnO economically by using the waste hot dipping zinc.

Surface modification of die casting mold steel by a composite technique of hot-dipping and plasma electrolytic oxidation

The hot dipping process of pure aluminum on H13 steel substrates followed by plasma electrolytic oxidation(PEO) was studied to form alumina ceramic coatings for protective purpose.H13 steel bars were first dipped in pure aluminum melts,and then,a reactive iron-aluminum intermetallic layer grew at the interface between the melt and the steel substrate.The reactive layer was mainly composed of intermetallic Fe-Al(Fe_2Al_5);the thickness of aluminum layer and Fe-Al intermetallic layer were mainly influenced by dipping time(1.5～12.0 min) and dipping temperature(710～760 ℃).After PEO process,uniform Al_2O_3 ceramic coatings were deposited on the surface of aluminized steel.The element distribution,phase composition and morphology of the aluminized layer,and the ceramic coatings were characterized by SEM/EDS and XRD.The distribution of hardness across the composite coating is demonstrated,and the maximum value reaches 1864 HV.The thermal shock resistance of the coated sample is also well improved.

Growth and corrosion behavior of rare earth film on hot-dip galvanized steel

Hot-dip galvanized(HDG)steel sheets were treated for 30 s?24 h by the rare earth aqueous solution containing 20 g/L Ce(NO3)3·6H2O,and the growth behavior and corrosion resistance of the rare earth film were investigated by SEM,EDS,AES and NSS.The results reveal that the rare earth film becomes thick while the mass gain of the samples does not distinctly change due to the zinc dissolution with the increase of treatment time.The film grows up more quickly and is apt to cracking in the vicinity of zinc grain boundaries,and eventually the film partly warps and flakes off with increasing film thickness.The NSS results show that the corrosion resistance of the film is dominated by both the film thickness and the cracks.With increasing treatment time,the corrosion resistance of the film increases within 1 h due to the increased film thickness and decreases after 1 h because the cracking and flaking off gradually become dominant factor.

CORROSION RESISTANCE OF HOT DIP GALVANIZED STEEL PRETREATED WITH BIS-FUNCTIONAL SILANES MODIFIED WITH NANOALUMINA

The corrosion behavior of hot dip galvanized steel pretrvated with bis-[triethoxysilylpropyl] tetrasulfide （BTESPT） modified with alumina particles was studied. The corrosion resistance of the passiving films was evaluated by Tafel polarization curve and electrochemical impedance spectroscopy. The films formed on the galvanized steel substrate were characterized by Fourier transform infrared spectroscopy and energy dispersive X-ray spectrometry. The surface morphology of the treated hot dip galvanized steel samples was observed by Field Emission Scanning Electron Microscope. The results show that the pretrvatments on the basis of silane films modified with nanoalumina particles have reduced both anodic and cathodic current densities, and increased total impedance in the measured frequency, consequently, improving corrosion protection for hot dip galvanized steel during immersion in NaCl solutions compared to chromate films and silane films.

Development of Hot Dip Galvanized Steel Strip and Its Application in Automobile Industry

Hot dip galvanized product is widely used in architecture, household electric appliance, ship vehicle, vessel, mechano-electronic device and other fields including clothing, food, housing, and travel. The history, development, market need, and technological advancement of hot dip galvanized strip, production situation, and development tendency in China are briefly introduced. The fact that it is necessary to build new and auto galvanized strip line with the development of the iron and steel industry in China.

THE INFLUENCE OF COMPOSITION AND TEMPERATURE OF BATH ANDAFTER-TREATMENT 0N COLORATION IN COLORING HOT DIPGALVANIZATION

The 08 Al steel sheets were hot dip ped into Zn - Mn bath with 0 1 % Mn and 0 2 % Mn at600 ～420 ℃ bath tem perature , and then w ere treated in different w ays . The after - treat ments include cooling in the air at room tem perature directly , holding at the upper part of thehot dip galvanizing furnace for 60 s an d then holding at 510 ±10 ℃for 90 s . The results in dicated that blue , yellow , and purple , w hose coloration varied with the co m position an d thetem perature of bath and the w ays of after - treat ment . Finally , the mechanism of coloredzinc coating w as discussed .

Heat Transfer during the Solidification of Hot Dip Aluminizing Coating

Hot dip aluminizing is one of the most effective methods of surface protection for steels and is gradually gaining popularity.Although the pulling speed is one of the most important parameters to control the coating thickness of aluminizing products,however,there are few publications on the mathematical modeling of pulling speed during the hot dip process.In order to describe the correlation among the pulling speed,coating thickness and solidification time,the principle of mass and heat transfer during the aluminizing process is investigated in this paper.The mathematical models are based on Navier-Stokes equation and heat transfer analysis.Experiments using the self-designed equipment are carried out to validate the mathematical models.Specifically,aluminum melt is purified at 730 ℃.The Cook-Norteman method is used for the pretreatment of Q235 steel plates.The temperature of hot dip aluminizing is set to 690 ℃ and thedipping time is set to 3 min.A direct current motor with stepless speed variation is used to adjust the pulling speed.The temperature change of the coating is recorded by an infrared thermometer,and the coating thickness is measured by using image analysis.The validate experiment results indicate that the coating thickness is proportional to the square root of pulling speed for the Q235 steel plate,and that there is a linear relationship between coating thickness and solidification time when the pulling speed is lower than 0.11 m/s.The prediction of the proposed model fits well with the experimental observations of the coating thickness.

Growth and corrosion behavior of molybdate passivation film on hot dip galvanized steel

Hot dip galvanized steel sheets were passivated by molybdate aqueous solution containing 10 g/L Na 2MoO 4·2H 2O, and the growth behavior and corrosion resistance of the passivation film were investigated. In the initial stage of passivation, the mass gain of film increases with passivation time proportionally. The film grows up more quickly and is apt to cracking at grain boundaries of zinc, then the cracks spread gradually on the whole surface of the film, and eventually the film will flake off with the increasing of film thickness. XPS results indicate that Mo compounds are present in Mo(Ⅵ) state on the surface of the film, and Mo(Ⅵ) and Mo(Ⅳ) states inside the film. NSS test shows that, the corrosion resistance of the passivation film decreases as the cracks occur, but in AASS test, the thicker the film is, the better the corrosion resistance is, the cracks of film have little effect on the corrosion resistance.

Crystallographic research of spangle on hot dip galvanized steel sheets

The spangles on hot dip galvanized steel sheet were investigated on an X-ray diffraction(XRD) meter by the rotating crystal method. The correlations between the crystallographic orientations of spangles and their morphologies were analyzed. The results show that the correlation can be classified into three types: β=0°, 0°<β<90° and β=90° by β. Crystallographic model of single spangle under the ideal condition was established based on the experimental results. The correlation between α and β can be deduced by their geometric relation as an equation.

The Effect of La on the Microstructure and Corrosion-resistance of Hot-dipped Aluminizing Steel

The effect of the content of rare-earth La on the microstructure and corrosion-resistance of hot-dipped aluminum was investigated in this paper. The results show that, under the same technology conditions, the thickness of hot-dipped aluminizing layer by adding the appropriate content of rare-earth La is about 2～3 times as much as that without rare-earth La, and the microstructure of hot-dipped aluminizing layer has also greatly changed ,and a great deal of phase Fe3Al was precipitated along the boundary of α phase. The corrosion resistance of the hot-dipped layer with rare-earth is greatly increased.

Effect of hot-dip galvanizing processes on the microstructure and mechanical properties of 600-MPa hot-dip galvanized dual-phase steel

A C–Mn dual-phase steel was soaked at 800°C for 90 s and then either rapidly cooled to 450°C and held for 30 s(process A) or rapidly cooled to 350°C and then reheated to 450°C(process B) to simulate the hot-dip galvanizing process. The influence of the hot-dip galvanizing process on the microstructure and mechanical properties of 600-MPa hot-dip galvanized dual-phase steel(DP600) was investigated using optical microscopy, scanning electron microscopy(SEM), transmission electron microscopy(TEM), and tensile tests. The results showed that, in the case of process A, the microstructure of DP600 was composed of ferrite, martensite, and a small amount of bainite. The granular bainite was formed in the hot-dip galvanizing stage, and martensite islands were formed in the final cooling stage after hot-dip galvanizing. By contrast, in the case of process B, the microstructure of the DP600 was composed of ferrite, martensite, bainite, and cementite. In addition, compared with the yield strength(YS) of the DP600 annealed by process A, that for the DP600 annealed by process B increased by approximately 50 MPa because of the tempering of the martensite formed during rapid cooling. The work-hardening coefficient(n value) of the DP600 steel annealed by process B clearly decreased because the increase of the YS affected the computation result for the n value. However, the ultimate tensile strength(UTS) and elongation(A80) of the DP600 annealed by process B exhibited less variation compared with those of the DP600 annealed by process A. Therefore, DP600 with excellent comprehensive mechanical properties(YS = 362 MPa, UTS = 638 MPa, A_(80) = 24.3%, n = 0.17) was obtained via process A.

Hot-Dip Galvanized Sheet Production and Application

Hot-dip galvanized sheet is wildly used in construction,household appliances,ship,vehicle and vessel building and machinery,etc.In last ten years,with the development of automobile industry,the anti-eorrosion requirements for car body are increasingly strict,by which the rapid development in technology has been promoted.The application of hot-dip galvanized sheet,technological progress in production and some Chinese large units were introduced.

Preparation and hot-dip galvanizing application of CeO_2/Zn nanocomposite

CeO2/Zn nanocomposite was fabricated by high-energy ball milling and subsequent hot-press sintering under vacuum. The produced nanocomposite powders and bulks were characterized using X-ray diffraction （XRD）, transmission electron microscopy （TEM） and scanning electron microscopy （SEM） with an energy dispersive X-ray spectrum （EDS）. The as-fabricated nanocomposite bulks were added successfully into the hot-dip galvanizing bath to improve the corrosion resistance of coatings. The results show that after milling for 120min, nano-sized CeO2 particles are distributed homogeneously on the surface of fine Zn particles to form spherical-like nanocomposite powder with narrow grain size distribution. The subsequent sintering does not lead to a dramatic grain growth, and the distribution of CeO2 nanoparticles in the composite bulk is also homogeneous. With the addition of as-prepared bulks, the corrosion resistance of the galvanized coatings is improved obviously. It provides a feasible route for adding CeO2 nanoparticles into the hot-dip galvanized coating.

Hot-Dip Coating of Lead-free Aluminum on Steel Substrates with Ultrasonic Vibration

Hot-dip coating has been practically employed in manufacturing zinc alloy coated steel sheets.However,it is difficult to coat aluminum alloy on a bulky steel substrate without sufficient preheating,because a rapidly solidified layer containing gas babbles is formed on a substrate surface.A variety of iron-aluminides are also formed at the interface of a steel and aluminum hot-dip coating system,which is the main difficulty in joining of steel with aluminum.Ultrasonic vibration was applied to a steel substrate during hot-dip coating of aluminum alloy to control a rapidly solidified layer and a brittle reaction layer.Hot dipping of columnar steel substrates into molten aluminum alloy （Al-2.7 mass fraction Si-4.6 mass fraction Sn） was carried out through the use of a Langevin oscillator with resonant frequency of 19.5 kHz.The application of ultrasonic vibration is quite effective to control a rapidly solidified layer and a surface oxide layer from a substrate surface by the sonocapillary effect based on a cavitation phenomenon,so that the intimate contact is achieved at the beginning of hot-dip coating.The application of ultrasonic vibration to hot-dipping is effective to control a reaction layer with less than 5 #m in thickness.An impact test exhibits that the good adhesive strength is approved in hot-dipped aluminum coatings with a thin reaction layer of approximately 5μm.

Analysis of causes and influence factors of small black spot defects in hot-dip galvanized pure Zn products

In this study,the factors affecting the formation of small black spot defects on the surface of a hot-dip galvanized pure zinc strip are analyzed. These defects are primarily formed w hen the iron-aluminum inhibition layer is incompletely formed or fails to form or when foreign matter adheres to the surface or embeds in the zinc layer.The defects can be reduced by controlling the cleanliness and activity of the strip base before coating,regulating the zinc pot process parameters,and ensuring the cleanliness of the passline and workshop.

Analysis of Coating Microstructure of Hot-Dip Aluminum of Deformed Low-Carbon Steel Containing Rare Earth

The coating microstructure of hot-dip aluminum (HDA) of deformed low-carbon steel containing RE was analyzed by metallography microscopy, TEM and XRD, and the forming mechanism was also discussed. The results show that, the Fe_2Al_5 phase, on whose subcrystal boundaries, Al particles with the size of 7～30 μm existing on parallel linear are, grows a strong orientation. And the spread activation energy of Al is 155.22 kJ·mol -1. In addition, the effects of deformation on coating microstructure of hot-dip aluminum and the function of RE were preliminarily analyzed.

ELECTROCHEMICAL CORROSION BEHAVIOR OF HOT DIP COATING IN ARTIFICIAL SEAWATER

The corrosion behavior of a zinc-baased alloy (compared with that of pure zinc) coating was studied in this research on the electrochemical corrosion behavior of hot dip coating in artificial seawater. The electrochemical parameters of these two hot dip coatings were measured by the galvanostatic method and accelerated corrosion test. The two coatings showed uniform corrosion, but the corrosion of the pure zinc coating was actively sustained continuously. The corrosion of the zinc-based alloy coating was very slow because of the formation of a stable anti-corrosion membrane. The corrosion mechanisms of these two coatings were also compared by the weak polarization curve fitting method. The corrosion of the zinc-based alloy coating is typical of that in natural passive corrosion system.

Formation of microstructural features in hot-dip aluminized AISI 321 stainless steel

Hot-dip aluminizing（HDA） is a proven surface coating technique for improving the oxidation and corrosion resistance of ferrous substrates. Although extensive studies on the HDA of plain carbon steels have been reported, studies on the HDA of stainless steels are limited. Because of the technological importance of stainless steels in high-temperature applications, studies of their microstructural development during HDA are needed. In the present investigation, the HDA of AISI 321 stainless steel was carried out in a pure Al bath. The microstructural features of the coating were studied using scanning electron microscopy and transmission electron microscopy. These studies revealed that the coating consists of two regions： an Al top coat and an aluminide layer at the interface between the steel and Al. The Al top coat was found to consist of intermetallic phases such as Al_7Cr and Al_3Fe dispersed in an Al matrix. Twinning was observed in both the Al_7Cr and the Al_3Fe phases. Furthermore, the aluminide layer comprised a mixture of nanocrystalline Fe_2Al_5, Al_7Cr, and Al. Details of the microstructural features are presented, and their formation mechanisms are discussed.

Effect of Mischmetal on Oxidation Resistance of 55Al－Zn Alloy Hot Dip Coating

The effect of mischmetal addition on high temperature oxidation resistance of 55wt% Al43.4 wt% Zn-1 .6wt% Si alloy hot-dip coatings has been investigated. It is found that rare earth addition improves high temperature oxidation resistance of the coatings. The oxidation tests at 800℃, 100 h and 1000℃, 50 h show that the coating with addition of 0. 1 % RE has the best properties. The morphology of oxide scale and element distribution of coating section were analysed by SEM, EPMA and XRD. It is indicated that mischmetal addition improves the adhesion between oxide scale and coating substrate, and spalling resistance of the scale is also improved with the addition of RE. Additionally, RE controls the degeneracy speed of Al-content in the coatings and inhibits the growth of Fe-Al intermetallic compound. For this reason, higher Al-content is kept in all the coatings with RE addition.