This paper proposes luteolin(LUT)as a novel depressant for the flotation-based separation of scheelite and calcite in a sodium oleate(NaOL)system.The suitability of LUT as a calcite depressant is confirmed through mic...This paper proposes luteolin(LUT)as a novel depressant for the flotation-based separation of scheelite and calcite in a sodium oleate(NaOL)system.The suitability of LUT as a calcite depressant is confirmed through micro-flotation testing.At pH=9,with LUT concentration of 50 mg·L^(-1) and NaOL concentration of 50 mg·L^(-1),scheelite recovery reaches 80.3%.Calcite,on the other hand,exhibits a recovery rate of 17.6%,indicating a significant difference in floatability between the two minerals.Subsequently,the surface modifica-tions of scheelite and calcite following LUT treatment are characterized using adsorption capacity testing,Zeta potential analysis,Fourier transform infrared spectroscopy(FT-IR),X-ray photoelectron spectroscopy(XPS),and atomic force microscopy(AFM).The study in-vestigates the selective depressant mechanism of LUT on calcite.Adsorption capacity testing and Zeta potential analysis demonstrate sub-stantial absorption of LUT on the surface of calcite,impeding the further adsorption of sodium oleate,while its impact on scheelite is min-imal.FT-IR and XPS analyses reveal the selective adsorption of LUT onto the surface of calcite,forming strong chemisorption bonds between the hydroxyl group and calcium ions present.AFM directly illustrates the distinct adsorption densities of LUT on the two miner-al types.Consequently,LUT can effectively serve as a depressant for calcite,enabling the successful separation of scheelite and calcite.展开更多
The impact of alkyl dimethyl betaine (ADB) on the collection capacity of sodium oleate (NaOl) at low temperatures was evaluated using flotation tests at various scales. The low-temperature synergistic mechanism of ADB...The impact of alkyl dimethyl betaine (ADB) on the collection capacity of sodium oleate (NaOl) at low temperatures was evaluated using flotation tests at various scales. The low-temperature synergistic mechanism of ADB and NaOl was explored by infrared spectroscopy, X-ray photoelectron spectroscopy, surface tension measurement, foam performance test, and flotation reagent size measurement.The flotation tests revealed that the collector mixed with octadecyl dimethyl betaine (ODB) and NaOl in a mass ratio of 4:96 exhibited the highest collection capacity. The combined collector could increase the scheelite recovery by 3.48% at low temperatures of 8–12℃. This is particularly relevant in the Luanchuan area, which has the largest scheelite concentrate output in China. The results confirmed that ODB enhanced the collection capability of NaOl by improving the dispersion and foaming performance. Betaine can be introduced as an additive to NaOl to improve the recovery of scheelite at low temperatures.展开更多
In this study, the innovative use of ethylenediamine tetramethylene phosphonic sodium(EDTMPS) as a calcite depressant in scheelite flotation was investigated by flotation experiments, and its selective depression mech...In this study, the innovative use of ethylenediamine tetramethylene phosphonic sodium(EDTMPS) as a calcite depressant in scheelite flotation was investigated by flotation experiments, and its selective depression mechanism was revealed by contact angle measurement, FTIR analysis, Zeta potential test and XPS analysis. The flotation experiment results showed that scheelite and calcite could be efficiently separated under the following conditions: pulp p H=9.5, Na OL concentration of 1.5×10^(-4)mol/L, EDTMPS concentration of 3.0×10^(-5)mol/L, a scheelite concentrate with WO3grade of 65.49%, recovery of 83.29%and separation efficiency of 65.29% could be obtained from the artificially mixed minerals. The analysis results of mineral surface properties demonstrated that EDTMPS was strongly adsorbed onto the calcite surface through the reaction between the phosphonate group and the calcium ions, which hindered Na OL adsorption and increased the hydrophilicity of calcite. However, EDTMPS had weak adsorption strength on the scheelite surface, which didn’t affect further adsorption of Na OL, hence, the scheelite remained hydrophobic. Consequently, the selective adsorption of EDTMPS on the two minerals’ surfaces increased a difference in wettability and thus enabling them to be separated by flotation. Finally, the mechanism model of this flotation separation process was established.展开更多
In this paper,using methyl cinnamate as raw material,the new cinnamic hydroxamic acid collector(CIHA)was synthesized by the hydroxylamine method.The collector performance of hydroxamic acid was investigated for scheel...In this paper,using methyl cinnamate as raw material,the new cinnamic hydroxamic acid collector(CIHA)was synthesized by the hydroxylamine method.The collector performance of hydroxamic acid was investigated for scheelite and gangue calcite,and the flotation separation test of scheelite and calcite was carried out with CIHA as the collector.The interaction mechanism between hydroxamic acid and scheelite minerals has also been investigated through zeta potential,Fourier transform infrared spectroscopy(FTIR)experiments,X-ray photoelectron spectroscopy(XPS)experiments,and density functional theory(DFT)calculation.The single mineral flotation test and artificially mixed ore showed that CIHA had an excellent collection effect and selectivity.Zeta potential,FTIR,and XPS showed that CIHA was adsorbed on the scheelite surface by strong chemical adsorption.The active group of CIHA was analyzed through quantum chemical calculation.It was speculated that C=O and N-O bonds could synthesize a five-membered chelated hydroxamic acid group with Ca element chelate on scheelite surface,changing hydrophobicity and making it more likely to emerge from the pulp.展开更多
Owing to the depletion of wolframite, the focus of tungsten extraction has gradually shifted to scheelite. However, separating the associated minerals(e.g., apatite, fluorite, and calcite) and scheelite is challenging...Owing to the depletion of wolframite, the focus of tungsten extraction has gradually shifted to scheelite. However, separating the associated minerals(e.g., apatite, fluorite, and calcite) and scheelite is challenging because their surface physicochemical properties are similar to those of scheelite. Fortunately, researchers have made substantial progress in separating the minerals of scheelite by using depressants. This study reviews the application and inhibition mechanism of inorganic depressants in obtaining tungsten from its calcium-bearing minerals. The application of new organic depressants in obtaining tungsten from its calcium-bearing minerals and the associated mechanisms are also summarized. After an objective assessment of inorganic and organic depressants’ advantages and disadvantages, possible future research directions for inorganic and organic depressants are proposed. Herein, we provide a theoretical basis for developing scheelite flotation depressants.展开更多
As the principal ore mineral in various tungsten(-gold)deposits,scheelite(CaWO_(4))plays an important role in directly dating the timing of ore formation,and in tracing associated material sources through the study of...As the principal ore mineral in various tungsten(-gold)deposits,scheelite(CaWO_(4))plays an important role in directly dating the timing of ore formation,and in tracing associated material sources through the study of its Sm-Nd geochronology and Nd isotopic characteristics.Since the retention of Sm-Nd systematics within scheelite is presently unconstrained,equivocal interpretations for isotopic data resulting from this method have occurred quite often in previous studies that apply these isotopic data.In order to better elucidate the closure of Sm-Nd in scheelite,the kinetics of Sm and Nd within this mineral lattice were investigated through calculation of diffusion constants presented herein.The following Arrhenius relations were obtained:D_(Nd)=4.00exp(-438 kJ·mol^(–1)/RT)cm^(2)/s D_(Sm)=1.85exp(-427 kJ·mol^(–1)/RT)cm^(2)/s showing diffusion rate of Nd is near identical to Sm in scheelite when at the same temperature.However,compared to other rare earth elements(REEs),which have markedly different atomic radii to either Nd or Sm,these are shown to exhibit a great variation in diffusivities.The observed trends in our data are in excellent agreement with the diffusion characteristics of REEs in other tetragonal ABO4 minerals,indicating that ionic radius is a key constraint to the diffusivity of REEs in the various crystal lattices.With this in mind,the same substitution mechanism and a very slight discrepancy in radii will allow us to infer that significant Sm/Nd diffusional fractionation in scheelite is unlikely to occur during most geological processes.Based upon the diffusion data determined herein,Sm and Nd closure temperatures and retention times in scheelite are discussed in terms of diffusion dynamics.Those results suggest that closure temperatures for Sm-Nd within this mineral are relatively high in contrast to the temperature ranges of ore-formation responsible for scheelite-related deposits,and any later thermal environments.It is likely,therefore,that relevant isotopic information could be easily retained under most geological conditions,since initial crystallization of the scheelite.In addition,comparison of this mineral-element pair over a range of temperatures with some other common minerals used as geochronometers(e.g.,zircon and apatite)indicates that Sm-Nd system has a slower diffusive rate in scheelite than for Sr in apatite or Ar in quartz,and only a little faster than for Pb in zircon.It should be noted,within most hydrothermal deposits where zircon has crystallized,its size is typically no more than 100μm,whereas scheelite commonly occurs as macroscopic grains.For this reason,the larger dimensions of scheelite would provide a robust Sm-Nd system more able to resist perturbations,relating to any later thermal process.As such Sm-Nd investigations of scheelite are akin to U-Pb within zircon samples used in isotopic dating.These observations indicate that Sm-Nd age and isotopic information can provide reliable data in all but the most extreme case,especially when data are extracted from macroscopic grains of scheelite that are chosen to be“pristine”(i.e.,free of surface alteration and/or fractures).展开更多
The ultra-fine grained(UFG)pure titanium was prepared by equal channel angular pressing(ECAP)and rotary swaging(RS).The strain controlled low cycle fatigue(LCF)test was carried out at room temperature.The fatigue life...The ultra-fine grained(UFG)pure titanium was prepared by equal channel angular pressing(ECAP)and rotary swaging(RS).The strain controlled low cycle fatigue(LCF)test was carried out at room temperature.The fatigue life prediction model and mean stress relaxation model under asymmetrical stress load were discussed.The results show that the strain ratio has a significant effect on the low cycle fatigue performance of the UFG pure titanium,and the traditional Manson-coffin model can not accurately predict the fatigue life under asymmetric stress load.Therefore,the SWT mean stress correction model and three-parameter power curve model are proposed,and the test results are verified.The final research shows that the threeparameter power surface model has better representation.By studying the mean stress relaxation phenomenon under the condition of R≠-1,it is revealed that the stress ratio and the strain amplitude are the factors that significantly afiect the mean stress relaxation rate,and the mean stress relaxation model with the two variables is calculated to describe the mean stress relaxation phenomenon of the UFG pure titanium under different strain ratios.The fracture morphology of the samples was observed by SEM,and it was concluded that the final fracture zone of the fatigue fracture of the UFG pure titanium was a mixture of ductile fracture and quasi cleavage fracture.The toughness of the material increases with the increase of strain ratio at the same strain amplitude.展开更多
Based on physicochemical study of the reaction between scheelite and NaOH, a new decomposition process for scheelite and scheelitewolframite concentrate, i. e., mechenically activating caustic decomposition has bee...Based on physicochemical study of the reaction between scheelite and NaOH, a new decomposition process for scheelite and scheelitewolframite concentrate, i. e., mechenically activating caustic decomposition has been developed, and it has been successfu展开更多
The depression behavior and mechanism of guar gum on talc-type scheelite flotation were systematically investigated by flotation experiments, adsorption tests, zeta-potential measurements, and infrared spectroscopic a...The depression behavior and mechanism of guar gum on talc-type scheelite flotation were systematically investigated by flotation experiments, adsorption tests, zeta-potential measurements, and infrared spectroscopic analyses. The flotation results for monominerals, mixed minerals, and actual mineral samples indicated that guar gum exhibited much higher selective depression for talc than for scheelite. Bench-scale closed-circuit tests showed that a tungsten concentrate with a WO_3 grade of 51.43% and a WO_3 recovery of 76.18% was obtained. Adsorption tests, zeta-potential measurements, and infrared spectral analyses confirmed that guar gum absorbed more strongly onto the talc surface than onto the scheelite surface because of chemisorption between guar gum and talc. This chemisorption is responsible for the guar gum's highly selective depression for talc and small depression for scheelite. The flotation results provide technical support for talc-type scheelite flotation.展开更多
The effect of different decomposition conditions on tungsten recovery forscheelite concentrate has been examined. The results show that tungsten recovery can be more than98% under decomposing conditions as follows: th...The effect of different decomposition conditions on tungsten recovery forscheelite concentrate has been examined. The results show that tungsten recovery can be more than98% under decomposing conditions as follows: the amount of caustic soda is 2.2 and 3.2 times oftheoretical respectively, ratio of water and ore is 0.7-0.8, temperature is 160℃, and preservationtime is 2.0 h for scheelite concentrate (63.21 % WO_3) and low grade scheelite concentrate (55.17%WO_3).展开更多
The Kukaazi Pb-Zn-Cu-W polymetallic deposit, located in the Western Kunlun orogenic belt, is a newly discovered skarn-type deposit. Ore bodies mainly occur in the forms of lenses and veins along beddings of the Mesopr...The Kukaazi Pb-Zn-Cu-W polymetallic deposit, located in the Western Kunlun orogenic belt, is a newly discovered skarn-type deposit. Ore bodies mainly occur in the forms of lenses and veins along beddings of the Mesoproterozoic metamorphic rocks. Three ore blocks, KⅠ,KⅡ, and KⅢ, have been outlined in different parts of the Kukaazi deposit in terms of mineral assemblages. The KⅠ ore block is mainly composed of chalcopyrite, scheelite,pyrrhotite, sphalerite, galena and minor pyrite, arsenopyrite,and molybdenite, whereas the other two ore blocks are made up of galena, sphalerite, magnetite and minor arsenopyrite and pyrite. In this study, we obtained a molybdenite isochron Re–Os age of 450.5 ± 6.4 Ma(2σ,MSWD = 0.057) and a scheelite Sm–Nd isochron age of 426 ± 59 Ma(2σ, MSWD = 0.49) for the KⅠ ore block.They are broadly comparable to the ages of granitoid in the region. Scheelite grains from the KⅠ ore block contain high abundances of rare earth elements(REE, 42.0–95.7 ppm)and are enriched in light REE compared to heavy REE, with negative Eu anomalies(δEu = 0.13–0.55). They display similar REE patterns and Sm/Nd ratios to those of the coeval granitoids in the region. Moreover, they also have similar Sr and Nd isotopes [ ^(87)Sr/ ^(86)Sr = 0.7107–0.7118;ε_(Nd)(t) =-4.1 to-4.0] to those of such granitoids, implying that the tungsten-bearing fluids in the Kukaazi deposit probably originate from the granitic magmas. Our results first defined that the Early Paleozoic granitoids could lead to economic Mo–W–(Cu) mineralization at some favorable districts in the Western Kunlun orogenic belt and could be prospecting exploration targets.展开更多
Cerium carbonate powders were produced in a submerged circulation impinging stream reactor (SCISR) from Ce(NO3)3· 6H2O. NH4HCO3 was used as a precipitant in the reaction. Cerium carbonate powders were roasted...Cerium carbonate powders were produced in a submerged circulation impinging stream reactor (SCISR) from Ce(NO3)3· 6H2O. NH4HCO3 was used as a precipitant in the reaction. Cerium carbonate powders were roasted to produce ultra-fine cerium dioxide (CeO2) powders. The optimal conditions of such production process were obtained by orthogonal and one-factor experiments. The results showed that ultra-fine and narrowly distributed cerium carbonate powders were produced under the optimal flowing conditions. The concentrations of Ce(NO3)3 and NH4HCO3 solutions were 02,5 and 0.3 mol · L^-1, respectively. The concentration of PEG4000 added in these two solutions was 4 g · L^-1. The stirring ratio, reaction temperature, feeding time, solution pH, reaction time and digestion time were 900 r · min^- 1,80 ℃, 20 min, 5 - 6, 5 min and 1 h, respectively. The final product, CeO2 powders, was obtained by roasting the produced cerium carbonate in air for 3 h at 500 ℃. The finally produced CeO2 powders were torispherical particles with a narrow size distribution of 0.8 -2.5 μm. The crystal structure of CeO2 powders belonged to cubic crystal system and its space point 5 group was OH^5-FM3M. Under optimal conditions, powders produced by SCISR were finer and more narrowly distributed than that by Stirred Tank Reactor (STR).展开更多
Dynamic rheological characteristics of polypropylene (PP) filled with ultra-fine full-vulcanized powdered rubber (UFPR) composed of styrene-butadiene copolymer were studied through dynamic rheological measurements on ...Dynamic rheological characteristics of polypropylene (PP) filled with ultra-fine full-vulcanized powdered rubber (UFPR) composed of styrene-butadiene copolymer were studied through dynamic rheological measurements on an Advanced Rheometric Expansion System (ARES). A specific viscoelastic phenomenon, i.e. 'the second plateau', appeared at low frequencies, and exhibits a certain dependence on the amount of rubber particles and the dispersion state in the matrix. This phenomenon is attributed to the formation of aggregation structure of rubber particles. The analyses of Cole-Cole diagrams of the dynamic viscoelastic functions suggest that the heterogeneity of the composites is enhanced on increasing both particle content and temperature.展开更多
The mechanochemical activation for leaching scheelite concentrate with NaOH solution was studied on a laboratory scale. Tungsten recovery more than 98% can be obtained for treating either scheelite concentrate with 66...The mechanochemical activation for leaching scheelite concentrate with NaOH solution was studied on a laboratory scale. Tungsten recovery more than 98% can be obtained for treating either scheelite concentrate with 66.37% WO 3 or middle grade scheelite concentrate with 41.83% WO 3 using relative low NaOH consumption.展开更多
After preparing the EU^3+-doped scheelite nano-material by Pechini method with the nanoparticles of 30-50 nm in diameter, X-ray diffraction (XRD), transmission electron microscopy (TEM) and high resolution transm...After preparing the EU^3+-doped scheelite nano-material by Pechini method with the nanoparticles of 30-50 nm in diameter, X-ray diffraction (XRD), transmission electron microscopy (TEM) and high resolution transmission electron microscopy (HRTEM) were used to show a microcosmic description of the particle morphology and crystal structure. The spectrum signature of the nano-scheelite, which was taken by fluorescence spectrometer, was used to discuss the difference of luminescent performance between the nano-scheelite and bulk scheelite. The atomic site of the nano-scheelite was intuitively shown through HRTEM images and HRTEM simulated images from the relation between luminescent properties and crystal structure, which was analyzed by spectrum probe. The results of antitumor activity examined by the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) method show that the inhibition of human promyelocytic leukemia cell line (HL60) is enhanced immediately with increasing the concentration and presents a reliance on the quantity. The results of fluorescence spectra and structure show that the antitumor activity has something to do with micro-structure and surface charge.展开更多
A new processing method,equal channel angular pressing(ECAP)plus cold rolling(CR),was applied to producing ultra-fine grained FeCoV alloy.The microstructures of ultra-fine grained FeCoV alloy after ECAP,ECAP plus CR,a...A new processing method,equal channel angular pressing(ECAP)plus cold rolling(CR),was applied to producing ultra-fine grained FeCoV alloy.The microstructures of ultra-fine grained FeCoV alloy after ECAP,ECAP plus CR,and the effect of tempering treatment on the microstructure of FeCoV alloy produced by ECAP plus CR were investigated.The results show that an elongated substructure with a width of about 0.3μm is obtained after four-pass ECAP using Route A.Cold rolling after ECAP cannot change the morphologies of elongated substructure,and it results in higher fraction of high-angle boundaries and higher dislocation density compared with the identical ECAP without rolling.Subsequent tempering for 30 min at 853 K brings about many nano-phases precipitating at subgrain boundaries and insides the grains,and the size of precipitated phase is measured to be about 10 nm.Nano-phases grow up with increasing tempering temperature and equiaxed structure forms at 883 K.展开更多
New cadmium and rare earth metal tungstates with the formula Cd0.25RE0.50 0.25WO4 (RE=Nd, Sin, Eu, Gd, D-statistical distrib- uted vacancies in cation sublattice) were synthesized by the solid-state reaction between...New cadmium and rare earth metal tungstates with the formula Cd0.25RE0.50 0.25WO4 (RE=Nd, Sin, Eu, Gd, D-statistical distrib- uted vacancies in cation sublattice) were synthesized by the solid-state reaction between CdWO4 and corresponding RE2W209. The obtained phases crystallize in the scheelite type structure. The Cd0.25RE0.5 0.25WO4 compounds were characterized by X-ray diffractometer (XRD), (DTA-TG), infrared (IR) and EPR methods.展开更多
Ultra-fine austenite grains with size of i-3 μm were prepared in a Nb-V-Ti steel through repetitive treatment of rapid heating and quenching. A model for the growth kinetics of these ultra-fine austenite grains was s...Ultra-fine austenite grains with size of i-3 μm were prepared in a Nb-V-Ti steel through repetitive treatment of rapid heating and quenching. A model for the growth kinetics of these ultra-fine austenite grains was successfully created through successive 2 processes, and the activation energy Q for growth was estimated to be about 693.2 kJ/mol, which directly shows the inhibition effect of microalloy elements on the growth of ultra-fine austenite grains.展开更多
Ultra-narrow gap welding (UNGW) process with high stabilization, reliability and without spatter can be achieved with constricted arc by molten slag wall, which is made from melted flux. The experiments are carried ...Ultra-narrow gap welding (UNGW) process with high stabilization, reliability and without spatter can be achieved with constricted arc by molten slag wall, which is made from melted flux. The experiments are carried out by changing voltage under different currents. The results indicate voltage range being fit for UNGW is about 22 -31 V under the current range of 200 -320 A. With the increasing of voltage, weld formation of UNGW has the law of lack of fusion on sidewall, good weld and undercut in turn under a certain current. In addition, the action relationships among arc, molten slag wall and sidewalls can be improved by properly adjusting voltage and current of arc, which makes cathode spot properly distribute in ultra-narrow gap. Therefore, the effective control of weld formation of UNGW has been achieved.展开更多
基金supported by the National Natural Science Foundation of China (No.52164022).
文摘This paper proposes luteolin(LUT)as a novel depressant for the flotation-based separation of scheelite and calcite in a sodium oleate(NaOL)system.The suitability of LUT as a calcite depressant is confirmed through micro-flotation testing.At pH=9,with LUT concentration of 50 mg·L^(-1) and NaOL concentration of 50 mg·L^(-1),scheelite recovery reaches 80.3%.Calcite,on the other hand,exhibits a recovery rate of 17.6%,indicating a significant difference in floatability between the two minerals.Subsequently,the surface modifica-tions of scheelite and calcite following LUT treatment are characterized using adsorption capacity testing,Zeta potential analysis,Fourier transform infrared spectroscopy(FT-IR),X-ray photoelectron spectroscopy(XPS),and atomic force microscopy(AFM).The study in-vestigates the selective depressant mechanism of LUT on calcite.Adsorption capacity testing and Zeta potential analysis demonstrate sub-stantial absorption of LUT on the surface of calcite,impeding the further adsorption of sodium oleate,while its impact on scheelite is min-imal.FT-IR and XPS analyses reveal the selective adsorption of LUT onto the surface of calcite,forming strong chemisorption bonds between the hydroxyl group and calcium ions present.AFM directly illustrates the distinct adsorption densities of LUT on the two miner-al types.Consequently,LUT can effectively serve as a depressant for calcite,enabling the successful separation of scheelite and calcite.
基金financially supported by the National Natural Science Foundation of China (Nos.51904339 and No.51974364)the Key Laboratory of Hunan Province for Clean and Efficient Utilization of Strategic Calcium-containing Mineral Resources,China (No.2018TP1002)the Co-Innovation Centre for Clean and Efficient Utilization of Strategic Metal Mineral Resources,and the Postgraduate Independent Exploration and Innovation Project of Central South University,China (No.2018zzts224)。
文摘The impact of alkyl dimethyl betaine (ADB) on the collection capacity of sodium oleate (NaOl) at low temperatures was evaluated using flotation tests at various scales. The low-temperature synergistic mechanism of ADB and NaOl was explored by infrared spectroscopy, X-ray photoelectron spectroscopy, surface tension measurement, foam performance test, and flotation reagent size measurement.The flotation tests revealed that the collector mixed with octadecyl dimethyl betaine (ODB) and NaOl in a mass ratio of 4:96 exhibited the highest collection capacity. The combined collector could increase the scheelite recovery by 3.48% at low temperatures of 8–12℃. This is particularly relevant in the Luanchuan area, which has the largest scheelite concentrate output in China. The results confirmed that ODB enhanced the collection capability of NaOl by improving the dispersion and foaming performance. Betaine can be introduced as an additive to NaOl to improve the recovery of scheelite at low temperatures.
基金the National Natural Science Foundation of China(Nos.51604302 and 51574282)the Key Laboratory of Hunan Province for Clean and Efficient Utilization of Strategic Calcium-containing Mineral Resources(No.2018TP1002).
文摘In this study, the innovative use of ethylenediamine tetramethylene phosphonic sodium(EDTMPS) as a calcite depressant in scheelite flotation was investigated by flotation experiments, and its selective depression mechanism was revealed by contact angle measurement, FTIR analysis, Zeta potential test and XPS analysis. The flotation experiment results showed that scheelite and calcite could be efficiently separated under the following conditions: pulp p H=9.5, Na OL concentration of 1.5×10^(-4)mol/L, EDTMPS concentration of 3.0×10^(-5)mol/L, a scheelite concentrate with WO3grade of 65.49%, recovery of 83.29%and separation efficiency of 65.29% could be obtained from the artificially mixed minerals. The analysis results of mineral surface properties demonstrated that EDTMPS was strongly adsorbed onto the calcite surface through the reaction between the phosphonate group and the calcium ions, which hindered Na OL adsorption and increased the hydrophilicity of calcite. However, EDTMPS had weak adsorption strength on the scheelite surface, which didn’t affect further adsorption of Na OL, hence, the scheelite remained hydrophobic. Consequently, the selective adsorption of EDTMPS on the two minerals’ surfaces increased a difference in wettability and thus enabling them to be separated by flotation. Finally, the mechanism model of this flotation separation process was established.
基金the National Nature Science Foundation of China(No.51774152)Jiangxi Provincial Education Department(GJJ200816)+1 种基金“Double height project”in Jiangxi province(No.[2022]223)the National Nature Science Foundation of China(No.52264023).
文摘In this paper,using methyl cinnamate as raw material,the new cinnamic hydroxamic acid collector(CIHA)was synthesized by the hydroxylamine method.The collector performance of hydroxamic acid was investigated for scheelite and gangue calcite,and the flotation separation test of scheelite and calcite was carried out with CIHA as the collector.The interaction mechanism between hydroxamic acid and scheelite minerals has also been investigated through zeta potential,Fourier transform infrared spectroscopy(FTIR)experiments,X-ray photoelectron spectroscopy(XPS)experiments,and density functional theory(DFT)calculation.The single mineral flotation test and artificially mixed ore showed that CIHA had an excellent collection effect and selectivity.Zeta potential,FTIR,and XPS showed that CIHA was adsorbed on the scheelite surface by strong chemical adsorption.The active group of CIHA was analyzed through quantum chemical calculation.It was speculated that C=O and N-O bonds could synthesize a five-membered chelated hydroxamic acid group with Ca element chelate on scheelite surface,changing hydrophobicity and making it more likely to emerge from the pulp.
基金financially supported by the National Natural Science Foundation of China (Nos.52174248 and 52264022)the Natural Science Foundation of Jiangxi Province,China (No.20202ACBL214010)+1 种基金the “Thousand Talents Plan” of Jiangxi Province,China (No.jxsq2019201115)the Youth Jinggang Scholars program in Jiangxi Province,China。
文摘Owing to the depletion of wolframite, the focus of tungsten extraction has gradually shifted to scheelite. However, separating the associated minerals(e.g., apatite, fluorite, and calcite) and scheelite is challenging because their surface physicochemical properties are similar to those of scheelite. Fortunately, researchers have made substantial progress in separating the minerals of scheelite by using depressants. This study reviews the application and inhibition mechanism of inorganic depressants in obtaining tungsten from its calcium-bearing minerals. The application of new organic depressants in obtaining tungsten from its calcium-bearing minerals and the associated mechanisms are also summarized. After an objective assessment of inorganic and organic depressants’ advantages and disadvantages, possible future research directions for inorganic and organic depressants are proposed. Herein, we provide a theoretical basis for developing scheelite flotation depressants.
基金financially supported by the National Natural Science Foundation of China(Grant No.41403035)the National Basic Research Program of China(Grant No.2014CB440901)。
文摘As the principal ore mineral in various tungsten(-gold)deposits,scheelite(CaWO_(4))plays an important role in directly dating the timing of ore formation,and in tracing associated material sources through the study of its Sm-Nd geochronology and Nd isotopic characteristics.Since the retention of Sm-Nd systematics within scheelite is presently unconstrained,equivocal interpretations for isotopic data resulting from this method have occurred quite often in previous studies that apply these isotopic data.In order to better elucidate the closure of Sm-Nd in scheelite,the kinetics of Sm and Nd within this mineral lattice were investigated through calculation of diffusion constants presented herein.The following Arrhenius relations were obtained:D_(Nd)=4.00exp(-438 kJ·mol^(–1)/RT)cm^(2)/s D_(Sm)=1.85exp(-427 kJ·mol^(–1)/RT)cm^(2)/s showing diffusion rate of Nd is near identical to Sm in scheelite when at the same temperature.However,compared to other rare earth elements(REEs),which have markedly different atomic radii to either Nd or Sm,these are shown to exhibit a great variation in diffusivities.The observed trends in our data are in excellent agreement with the diffusion characteristics of REEs in other tetragonal ABO4 minerals,indicating that ionic radius is a key constraint to the diffusivity of REEs in the various crystal lattices.With this in mind,the same substitution mechanism and a very slight discrepancy in radii will allow us to infer that significant Sm/Nd diffusional fractionation in scheelite is unlikely to occur during most geological processes.Based upon the diffusion data determined herein,Sm and Nd closure temperatures and retention times in scheelite are discussed in terms of diffusion dynamics.Those results suggest that closure temperatures for Sm-Nd within this mineral are relatively high in contrast to the temperature ranges of ore-formation responsible for scheelite-related deposits,and any later thermal environments.It is likely,therefore,that relevant isotopic information could be easily retained under most geological conditions,since initial crystallization of the scheelite.In addition,comparison of this mineral-element pair over a range of temperatures with some other common minerals used as geochronometers(e.g.,zircon and apatite)indicates that Sm-Nd system has a slower diffusive rate in scheelite than for Sr in apatite or Ar in quartz,and only a little faster than for Pb in zircon.It should be noted,within most hydrothermal deposits where zircon has crystallized,its size is typically no more than 100μm,whereas scheelite commonly occurs as macroscopic grains.For this reason,the larger dimensions of scheelite would provide a robust Sm-Nd system more able to resist perturbations,relating to any later thermal process.As such Sm-Nd investigations of scheelite are akin to U-Pb within zircon samples used in isotopic dating.These observations indicate that Sm-Nd age and isotopic information can provide reliable data in all but the most extreme case,especially when data are extracted from macroscopic grains of scheelite that are chosen to be“pristine”(i.e.,free of surface alteration and/or fractures).
基金Funded by National Natural Science Foundation of China(No.51474170)the Key Laboratory Project of Shaanxi Provincial Department of Education(No.20js075)。
文摘The ultra-fine grained(UFG)pure titanium was prepared by equal channel angular pressing(ECAP)and rotary swaging(RS).The strain controlled low cycle fatigue(LCF)test was carried out at room temperature.The fatigue life prediction model and mean stress relaxation model under asymmetrical stress load were discussed.The results show that the strain ratio has a significant effect on the low cycle fatigue performance of the UFG pure titanium,and the traditional Manson-coffin model can not accurately predict the fatigue life under asymmetric stress load.Therefore,the SWT mean stress correction model and three-parameter power curve model are proposed,and the test results are verified.The final research shows that the threeparameter power surface model has better representation.By studying the mean stress relaxation phenomenon under the condition of R≠-1,it is revealed that the stress ratio and the strain amplitude are the factors that significantly afiect the mean stress relaxation rate,and the mean stress relaxation model with the two variables is calculated to describe the mean stress relaxation phenomenon of the UFG pure titanium under different strain ratios.The fracture morphology of the samples was observed by SEM,and it was concluded that the final fracture zone of the fatigue fracture of the UFG pure titanium was a mixture of ductile fracture and quasi cleavage fracture.The toughness of the material increases with the increase of strain ratio at the same strain amplitude.
文摘Based on physicochemical study of the reaction between scheelite and NaOH, a new decomposition process for scheelite and scheelitewolframite concentrate, i. e., mechenically activating caustic decomposition has been developed, and it has been successfu
基金financially supported by the National Natural Science Foundation of China (No.51404218)the National Key Technology R&D Program (No.2015BAB12B02)the Science and Technology Planning Project of Guangdong Province, China (No.2013B090800016)
文摘The depression behavior and mechanism of guar gum on talc-type scheelite flotation were systematically investigated by flotation experiments, adsorption tests, zeta-potential measurements, and infrared spectroscopic analyses. The flotation results for monominerals, mixed minerals, and actual mineral samples indicated that guar gum exhibited much higher selective depression for talc than for scheelite. Bench-scale closed-circuit tests showed that a tungsten concentrate with a WO_3 grade of 51.43% and a WO_3 recovery of 76.18% was obtained. Adsorption tests, zeta-potential measurements, and infrared spectral analyses confirmed that guar gum absorbed more strongly onto the talc surface than onto the scheelite surface because of chemisorption between guar gum and talc. This chemisorption is responsible for the guar gum's highly selective depression for talc and small depression for scheelite. The flotation results provide technical support for talc-type scheelite flotation.
文摘The effect of different decomposition conditions on tungsten recovery forscheelite concentrate has been examined. The results show that tungsten recovery can be more than98% under decomposing conditions as follows: the amount of caustic soda is 2.2 and 3.2 times oftheoretical respectively, ratio of water and ore is 0.7-0.8, temperature is 160℃, and preservationtime is 2.0 h for scheelite concentrate (63.21 % WO_3) and low grade scheelite concentrate (55.17%WO_3).
基金funded by a "Chinese NSF" Project (41272114) to Xingchun Zhanga "CAS Western Light Talent Culture" Project to Chengbiao Lenga "CAS Hundred Talents" Project to Jianfeng Gao
文摘The Kukaazi Pb-Zn-Cu-W polymetallic deposit, located in the Western Kunlun orogenic belt, is a newly discovered skarn-type deposit. Ore bodies mainly occur in the forms of lenses and veins along beddings of the Mesoproterozoic metamorphic rocks. Three ore blocks, KⅠ,KⅡ, and KⅢ, have been outlined in different parts of the Kukaazi deposit in terms of mineral assemblages. The KⅠ ore block is mainly composed of chalcopyrite, scheelite,pyrrhotite, sphalerite, galena and minor pyrite, arsenopyrite,and molybdenite, whereas the other two ore blocks are made up of galena, sphalerite, magnetite and minor arsenopyrite and pyrite. In this study, we obtained a molybdenite isochron Re–Os age of 450.5 ± 6.4 Ma(2σ,MSWD = 0.057) and a scheelite Sm–Nd isochron age of 426 ± 59 Ma(2σ, MSWD = 0.49) for the KⅠ ore block.They are broadly comparable to the ages of granitoid in the region. Scheelite grains from the KⅠ ore block contain high abundances of rare earth elements(REE, 42.0–95.7 ppm)and are enriched in light REE compared to heavy REE, with negative Eu anomalies(δEu = 0.13–0.55). They display similar REE patterns and Sm/Nd ratios to those of the coeval granitoids in the region. Moreover, they also have similar Sr and Nd isotopes [ ^(87)Sr/ ^(86)Sr = 0.7107–0.7118;ε_(Nd)(t) =-4.1 to-4.0] to those of such granitoids, implying that the tungsten-bearing fluids in the Kukaazi deposit probably originate from the granitic magmas. Our results first defined that the Early Paleozoic granitoids could lead to economic Mo–W–(Cu) mineralization at some favorable districts in the Western Kunlun orogenic belt and could be prospecting exploration targets.
基金Project supported by the National Natural Science Foundation of China (50474022 and 50574069 )
文摘Cerium carbonate powders were produced in a submerged circulation impinging stream reactor (SCISR) from Ce(NO3)3· 6H2O. NH4HCO3 was used as a precipitant in the reaction. Cerium carbonate powders were roasted to produce ultra-fine cerium dioxide (CeO2) powders. The optimal conditions of such production process were obtained by orthogonal and one-factor experiments. The results showed that ultra-fine and narrowly distributed cerium carbonate powders were produced under the optimal flowing conditions. The concentrations of Ce(NO3)3 and NH4HCO3 solutions were 02,5 and 0.3 mol · L^-1, respectively. The concentration of PEG4000 added in these two solutions was 4 g · L^-1. The stirring ratio, reaction temperature, feeding time, solution pH, reaction time and digestion time were 900 r · min^- 1,80 ℃, 20 min, 5 - 6, 5 min and 1 h, respectively. The final product, CeO2 powders, was obtained by roasting the produced cerium carbonate in air for 3 h at 500 ℃. The finally produced CeO2 powders were torispherical particles with a narrow size distribution of 0.8 -2.5 μm. The crystal structure of CeO2 powders belonged to cubic crystal system and its space point 5 group was OH^5-FM3M. Under optimal conditions, powders produced by SCISR were finer and more narrowly distributed than that by Stirred Tank Reactor (STR).
基金This work was supported by the National Science Fund for Distinguished Young Scholars of China (No.50125312) andSpecial Funds for Major State Basic Research Projects (No.G1999064800).
文摘Dynamic rheological characteristics of polypropylene (PP) filled with ultra-fine full-vulcanized powdered rubber (UFPR) composed of styrene-butadiene copolymer were studied through dynamic rheological measurements on an Advanced Rheometric Expansion System (ARES). A specific viscoelastic phenomenon, i.e. 'the second plateau', appeared at low frequencies, and exhibits a certain dependence on the amount of rubber particles and the dispersion state in the matrix. This phenomenon is attributed to the formation of aggregation structure of rubber particles. The analyses of Cole-Cole diagrams of the dynamic viscoelastic functions suggest that the heterogeneity of the composites is enhanced on increasing both particle content and temperature.
文摘The mechanochemical activation for leaching scheelite concentrate with NaOH solution was studied on a laboratory scale. Tungsten recovery more than 98% can be obtained for treating either scheelite concentrate with 66.37% WO 3 or middle grade scheelite concentrate with 41.83% WO 3 using relative low NaOH consumption.
基金supported by the National Natural Science Foundation of China(No.40072013)
文摘After preparing the EU^3+-doped scheelite nano-material by Pechini method with the nanoparticles of 30-50 nm in diameter, X-ray diffraction (XRD), transmission electron microscopy (TEM) and high resolution transmission electron microscopy (HRTEM) were used to show a microcosmic description of the particle morphology and crystal structure. The spectrum signature of the nano-scheelite, which was taken by fluorescence spectrometer, was used to discuss the difference of luminescent performance between the nano-scheelite and bulk scheelite. The atomic site of the nano-scheelite was intuitively shown through HRTEM images and HRTEM simulated images from the relation between luminescent properties and crystal structure, which was analyzed by spectrum probe. The results of antitumor activity examined by the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) method show that the inhibition of human promyelocytic leukemia cell line (HL60) is enhanced immediately with increasing the concentration and presents a reliance on the quantity. The results of fluorescence spectra and structure show that the antitumor activity has something to do with micro-structure and surface charge.
基金Project(50675133)supported by the National Natural Science Foundation of ChinaProject(2006CB705401)supported by the National Basic Research Program of China
文摘A new processing method,equal channel angular pressing(ECAP)plus cold rolling(CR),was applied to producing ultra-fine grained FeCoV alloy.The microstructures of ultra-fine grained FeCoV alloy after ECAP,ECAP plus CR,and the effect of tempering treatment on the microstructure of FeCoV alloy produced by ECAP plus CR were investigated.The results show that an elongated substructure with a width of about 0.3μm is obtained after four-pass ECAP using Route A.Cold rolling after ECAP cannot change the morphologies of elongated substructure,and it results in higher fraction of high-angle boundaries and higher dislocation density compared with the identical ECAP without rolling.Subsequent tempering for 30 min at 853 K brings about many nano-phases precipitating at subgrain boundaries and insides the grains,and the size of precipitated phase is measured to be about 10 nm.Nano-phases grow up with increasing tempering temperature and equiaxed structure forms at 883 K.
文摘New cadmium and rare earth metal tungstates with the formula Cd0.25RE0.50 0.25WO4 (RE=Nd, Sin, Eu, Gd, D-statistical distrib- uted vacancies in cation sublattice) were synthesized by the solid-state reaction between CdWO4 and corresponding RE2W209. The obtained phases crystallize in the scheelite type structure. The Cd0.25RE0.5 0.25WO4 compounds were characterized by X-ray diffractometer (XRD), (DTA-TG), infrared (IR) and EPR methods.
基金supported by the National Natural Science Foundation of China(No.50527402)
文摘Ultra-fine austenite grains with size of i-3 μm were prepared in a Nb-V-Ti steel through repetitive treatment of rapid heating and quenching. A model for the growth kinetics of these ultra-fine austenite grains was successfully created through successive 2 processes, and the activation energy Q for growth was estimated to be about 693.2 kJ/mol, which directly shows the inhibition effect of microalloy elements on the growth of ultra-fine austenite grains.
基金The work was supported by National Natural Science Foundation of China (51105185) and Advanced Project Foundation of Jinchuan Company(420032).
文摘Ultra-narrow gap welding (UNGW) process with high stabilization, reliability and without spatter can be achieved with constricted arc by molten slag wall, which is made from melted flux. The experiments are carried out by changing voltage under different currents. The results indicate voltage range being fit for UNGW is about 22 -31 V under the current range of 200 -320 A. With the increasing of voltage, weld formation of UNGW has the law of lack of fusion on sidewall, good weld and undercut in turn under a certain current. In addition, the action relationships among arc, molten slag wall and sidewalls can be improved by properly adjusting voltage and current of arc, which makes cathode spot properly distribute in ultra-narrow gap. Therefore, the effective control of weld formation of UNGW has been achieved.