A homogeneous atmospheric pressure air plasma in a 10 mm gap based on a three-electrode configuration

Generation of atmospheric pressure homogeneous air plasma in a large gap(>4 mm)is a challenge.In this study,an atmospheric pressure homogeneous air plasma generated in a gap up to 10 mm is reported,which is based on a three-electrode configuration,where a high-voltage(HV)electrode and a middle electrode form a surface dielectric barrier discharge(S-DBD),and together with the ground electrode form the main volume discharge.High-speed photographs confirm that the discharge in the main gap is homogeneous.The gas temperature of the plasma estimated from the N_(2)(C^(3)∏_(u)-B^(3)∏_(g))(Δv=-2)emission is about 320 K,which is close to room temperature.A detailed analysis shows that the discharge ignited between the HV electrode and the middle electrode is serving as an electron source,and the electrons deposited on the dielectric plate are due to the S-DBD along with the applied voltage generating a driving force,which results in a high concentration of seed electrons in the main gap and induces the homogeneous plasma.Further analysis shows that the electric field in the main gap is only about18.45 k V·cm^(-1),which is much lower than the typical breakdown electric field of 30 k V·cm^(-1)for atmospheric pressure air discharge.

Formulation development and preparation of fish oil liposome by using high pressure homogenizer for food supplement product

It is known that “Fish Oil” is the raw material that has lot of benefits for health, because fish oil consists of several necessary unsaturated fatty acids, particularly Omega-3 and Docosahexanoic acid (DHA). Omega-3 can decrease triglyceride level, and then it can increase HDL cholesterol level. In addition, DHA can support brain cell synthesis and also nervous system for human.

The Role of Metastable Atoms in a Homogeneous Atmospheric Pressure Barrier Discharge in Helium

A one-dimensional fluid model for homogeneous atmospheric pressure barrier discharges in helium is presented by considering elementary processes of excitation and ionization including a metastable atom effect. Using this model we investigate the behaviours of the helium metastable atoms in discharges as well as their influence on the discharge characteristics. It is shown that the metastable atoms with a relatively high concentration during the discharge are mainly produced in the active phase of the discharge and dissolved in the off phase. It is also found that the metastable atom collisions can not only provide seed electrons for discharges but also influence the concentration of ions. A reduction of matestable atom density results in a drop in the charged particle densities and causes a qualitative change in the discharge patterns.

Structural, Pasting, and Thermal Properties of Ultra-high Pressure-treated Lotus Seed Starch

Lotus seed starch （15%, w/w） was subjected to ultra-high pressure （UHP） at 500 MPa for 10～60 min. The effects of UHP on the structural, pasting, and thermal properties of starch were investigated using solid-state 13C CP/MAS NMR, differential scanning calorimetry （DSC）, HPSEC-MALLS-RI, and a rapid visco analyzer. The 13C CP/MAS NMR results revealed a reduction in the relative crystallinity and peak intensity of the crystalline state with increasing the UHP time. The molecular weight of native starch was 1.433 × 107 Da, which was higher than that of the UHP-treated starch. Viscograms of UHP-treated starch revealed an increase in paste viscosity, peak time, and pasting temperature and a reduction in breakdown and setback viscosity compared to the native starch. Furthermore, the DSC results showed a reduction in gelatinization temperature and gelatinization enthalpy with increasing the UHP time.

Homogeneous Isolation of Nanocellulose from Cotton Cellulose by High Pressure Homogenization

Nano-cellulose materials are widely believed to have the potential to push polymer mechanical properties. The cotton cellulose was dissolved in ionic liquid (1-butyl-3-methylimidazolium chloride ([Bmim]Cl)), and then was isolated by high pressure homogenization in a homogeneous media. The nano-cellulose was obtained at 80MPa for 30 cycles. The geometry and microstructure of the cellulose nano-fibres were observed by SEM and their particle size analysis. FTIR, XRD and TGA were used to characterize changes to chemical functionality. Particular emphasis is given to the physical and chemical characterization of these nano-fibres together with their thermal stability and crystallinity, in order to develop their suitability.

Effect of high-pressure homogenization on stability of emulsions containing zein and pectin

The aim of this study was to investigate the effect of high-pressure homogenization on the droplet size and physical stability of different formulations of pectin–zein stabilized rice bran oil emulsions. The obtained emulsions, both before and after passing through highpressure homogenizer, were subjected to stability test under environmental stress conditions,that is, temperature cycling at 4 °C/40 °C for 6 cycles and centrifugal test at 3000 rpm for 10 min. Applying high-pressure homogenization after mechanical homogenization caused only a small additional decrease in emulsion droplet size. The droplet size of emulsions was influenced by the type of pectin used;emulsions using high methoxy pectin(HMP) were smaller than that using low methoxy pectin(LMP). This is due to a greater emulsifying property of HMP than LMP. The emulsions stabilized by HMP–zein showed good physical stability with lower percent creaming index than those using LMP, both before and after passing through high-pressure homogenizer. The stability of emulsions after passing through high-pressure homogenizer was slightly higher when using higher zein concentration, resulting from stronger pectin–zein complexes that could rearrange and adsorb onto the emulsion droplets.

Hydrodynamics of air-kerosene bubble column under elevated pressure in homogeneous flow regime

A multiphase computational fluid dynamics(CFD)model coupled with the population balance equation(PBE)was developed in a homogeneous air-kerosene bubble column under elevated pressure(P).The specific pressure drop(ΔP/L),gas holdup(α_(G)),and Sauter mean diameter(d_(32))were experimentally measured in the bubble column with 1.8 m height and 0.1 m inner diameter,which was operated at a superficial gas velocity of 12.3 mm·s^(-1),and P=1-35 bar(1 bar=10^(5) Pa).A modified drag coefficient model was proposed to consider the effect of bubble swarm and pressure on hydrodynamics of the bubble column.The Luo breakage model was modified to account for liquid density,viscosity,surface tension and gas density.TheΔP/L,α_(G),and d_(32) obtained from the CFD model were compared with experimental data,and the gas density-dependent parameters of the CFD model were identified.With increasing P from 1 to 35 bar,theα_(G) varied from 5.4%to 7.2% and the d32 decreased from 2.3 to 1.5 mm.The CFD-PBE model is applicable to predict hydrodynamics of pressurized bubble columns for gas-organic liquid in the homogeneous regime.

Effect of High Pressure Homogenization Treatment on Structure and Properties of Soybean Residue Cellulose Nanofibers

To reduce the adverse effects of non-cellulose materials on subsequent homogenization,the effects of a high-pressure homogenization treatment on the structure and properties of cellulose nanofibers(CNF)prepared by acid treatment of soybean residue were studied.The effects of the number of homogenization step on the microfibrillation degree,crystalline structure and mechanical properties of the soybean residue were analyzed by SEM,FT-IR,XRD,TG and DTG.The results showed that an increase in the number of homogenization steps led to an increase in the degree of microfibrillation,a more uniform distribution of the CNF diameter,and an increase in the crystallinity of CNF.However,but when the number of homogenization steps exceeded 15,the rate of change decreased,and the crystallinity of CNF decreased.As the number of homogenization steps increased,the average degree of polymerization and average molecular weight of CNF decreased continuously,and after 15 homogenization steps,their rate of change also decreased.Therefore,15 steps of high-pressure homogenization represented a suitable number of steps to prepare the soybean residue CNF with an average diameter of 15 nm.

Effects of ultra-high hydrostatic pressure on foaming and physical-chemistry properties of egg white

The influences of ultra-high hydrostatic pressure treatment on foaming and physical properties (solubility, hydrophobicity and sulfhydryl content) of egg white were investigated. A pressure range of 0-500 MPa, time range of 0-20 min and pH range of 7.5-8.5 were selected. The foaming property of egg white is improved by 350Mpa and 10min. The treatment resulted in in- crease of sulfhydryl content of egg white, while solubility and hydrophobicity were significantly decreased.

Impact of High Pressure Homogenization (HPH) Treatment on the Nutritional Quality of Egg/Yogurt, Vegetable and Fruit Based Creams

The food industry has made large investments in processing facilities relying mostly on conventional thermal processing technologies with well-established reliability and efficacy. These techniques have important disadvantages such as off flavors, destruction of nutrients, and other losses of product quality. Non thermal processing is a key factor for preserving or improving the nutritional value of food, and high pressure homogenization (HPH) processing is now a celebrated option experiencing worldwide commercial growth. Notwithstanding, little is known on the impact of HPH treatments on the nutritional value of food. In this study we have evaluated the possible modification induced by HPH treatment in egg-yogurt, mixed vegetable, and mixed fruit creams. Our results evidence that HPH does not affect the nutritional quality of lipids and does not cause lipolysis, lipid peroxidation and vitamin E loss. In plant food products, HPH preserved or improved the nutritional quality, suggesting its use as valid alternative to thermal pasteurization for obtaining high quality products with preserved nutritional characteristics. Although further investigations are needed, especially at extreme pressure and temperature combinations, our results open new perspectives for the production of ambient stable products with good nutritional value, and contribute to process optimization.

Analysis on performance and test of a new type of ultra-high pressure pipe joint

Analysis as well as application of ultra-high pressure hydraulic system and elements has become a trend. The structure and operation principle of a new type of ultra-high pressure pipe joint is introduced. The structure of the new type of ultra-high pressure pipe joint is simple and is easy to be produced. The finite element model on two working conditions( preload condition with 30 N·m torque and static-loading condition with 70 MPa pressure) is built and computed. The width of contact area,the equivalent stress status,as well as the contact pressure status are plotted and analyzed. According to the national standard,test on air-tightness,blasting,and cyclic endurance is conducted and the results show that the new type of ultra-high pressure pipe joint has the sealability for ultra-high pressure up to 70 MPa,and the DN6 ultra-high pressure pipe joint can provide effective seal under70 MPa fluid pressure. The research can provide a thinking and method on designing ultra-high pressure pipe joint and push forward the development of ultra-high pressure hydraulic system.

Enzymatic Hydrolysis of Hairtail Surimi in an Ultra-High Pressure Bioreactor

Amino acids have been extracted from Hairtail surimi using enzymes in an ultra-high pressure bioreactor. The extraction efficiency of different enzymes including papain, trypsin, and proteases (acid, neutral, alkaline) also has been evaluated, and it has been discovered that neutral protease behaved the best. The amino acids were analyzed using automatic amino acid analyzer, and the enzymatic digestion conditions were optimized. For neutral protease, the optimal condition was 50℃, 250 MPa, pH 7.0. Material to liquid ratio of enzyme is 6%. More than 29 amino acids were detected after 24 hours of hydrolysis;the enzymatic hydrolysis rate can reach 83.29%. The results show that enzymatic digestion under ultra-high-pressure provides a very promising approach to extract amino acids from Hairtail surimi.

THERMAL MODELLING OF COLLISIONAL OROGENY: IMPLICATIONS FOR THE ULTRA-HIGH PRESSURE METAMORPHISM

The petrological research on the ultra high pressure metamorphism (UHP) of collisional orogen indicates that the upper crustal rocks is subducted to depths exceeding 100 km, and returned to the surface rapidly. In this study, we investigate the thermal structure of collisional orogen as a slab of continental lithosphere being subducted beneath an overriding wedge of continental lithosphere by the 2 D finite element method. The advection heat transfer due to the accretion of orogenic wedge is considered. The wedge is composed of the upper crust materials through the accretion from the down going plate to the upper plate. For identifying the significance of the geometric and/or kinetic factors on the thermal structure of continental subduction, the different combinations of parameters, including dip angle of subduction zone, accretion or erosion rates, and the convergence velocity etc., are used in modelling. The time span of continental subduction in our calculation is less than 30 Ma, according to the short duration of ultra deep subduction of continental slab suggested by the preservation of metastable pre peak low pressure mineralogy assemblage in the garnet of UHP rocks. Therefore, the steep dip angle of down going plate and/or low rate of accretion favour the ultra deep subduction of upper crust materials, especially for the slower down going slab. Meanwhile, taking the erosion rate as the level of exhumation rate of UHP rocks in some orogens (i.e., 1-2 km/Ma or more) does not result in the anatexis melting of crust of the overriding plate, due to the cooling effect of the rapid down going slab. However, the temperature structures of all models are generally cooler than those recovered by thermobarometric studies of the UHP rocks. This implies the significant increase of temperature after the rapid subduction of continental slab. Following the method of Davies and von Blackenburg (1998), we show that the slab breakoff can occur at the depth exceeding 100 km. Thermal modelling on the post subduction stage shows the heating related to the plate breakoff can cause the higher temperature recorded by the exhumed UHP rocks. The higher geotherm during post subduction stage leads to the weak strength of the orogenic wedge, and favours the faster upward movement of the UHP rock slices as ductile agents. The lower temperature gradient of the subduction slab predicted by modelling suggests the cold subducting slab could have transported significant fluids to mantle depth, not released during subduction. Accordingly, the absence of coeval calc alkalic magmatism in UHP orogens might resulted from the lower temperature as well as the fluid free circumstance, both are related to the rapid subduction of cold plate. Therefore, shear heating is not needed for explanation the thermal evolution of UHP orogen. On the other hand, the post collisional or late stage granitic plutonism is closely related to the deep seated heat producing materials of the accretion wedge.

Cyclic Pulsating Pressure Enhanced Segregating Structuration of Ultra-High Molecular Weight Polyethylene/Graphene Composites as High-performance Light-Weight EMI Shields

Currently,the enhancement in electromagnetic interference(EMI)performance of polymeric composite generally relies on either improving electrical conductivity(σ)for stronger electromagnetic(EM)reflections or tailoring structure for higher EM resonances.Herein,we proposed a novel technique called cyclic pulsating pressure enhanced segregating structuration(CPP-SS),which can reinforce these two factors simultaneously.The structural information was supplied by optical microscopy(OM)and scanning electron microscopy(SEM),both of which confirmed the formation and evolution of segregate structured ultra-high molecular weight polyethylene(UHMWPE)/graphene composites.Then,the result showed that CPP-SS can significantly improve theσof samples.Ultimately,advanced specific EMI shielding efficiency of 31.1 d B/mm was achieved for UHMWPE/graphene composite at 1-mm thickness and a low graphene loading of 5 wt%.Meanwhile,it also confirmed that the intrinsic disadvantage of poor mechanical properties of conventional segregated structure composites can be surpassed.This work is believed to provide a fundamental understanding of the structural and performance evolutions of segregated structured composites prepared under CPPSS,and to bring us a simple and efficient approach for fabricating high-performance,strong and light-weight polymeric EMI shields.

Polyarylacetylene as a novel graphitizable precursor for fabricating high-density C/C composite via ultra-high pressure impregnation and carbonization

High-density carbon/carbon(C/C)composite plays a critical role in the aerospace industry owing to excellent mechanical properties and resistance to ablation.However,traditional manufacturing relies on pitch precursor and hot isostatic pressure impregnation and carbonization(HIPIC)technology,which is time-consuming and expensive.In this study,we report an innovative method utilizing polyarylacetylene(PAA)resin and ultra-high pressure impregnation and carbonization(UHPIC)technology.The extremely high char yield of PAA resin(85 wt.%)and high isotropic pressure of UHPIC(over 200 MPa)promote the densification of the composite.As a result,we achieve a high-density(1.90 g/cm^(3))C/C composite with a high degree of graphitization(81%).This composite exhibits impressive properties,including flexural strength of 146 MPa,compressive strength of 187 MPa,and thermal conductivity of 147 W/(m K).When exposed to oxyacetylene flame at 3000 K for 100 s,it displays minimal linear ablation,with a rate of 1.27×10^(-2)mm/s.This study demonstrates the exceptional graphitizable characteristic of PAA resin,setting it apart from conventional resins.Our time-saving and cost-effective approach holds significant promise for aerospace applications,particularly in harsh aerodynamic heating environments.

Nanosecond Repetitively Pulsed Dielectric Barrier Discharge in Air at Atmospheric Pressure

Dielectric barrier discharge （DBD） between two cylindrical glass containers with salt water generated by a nanosecond repetitively pulsed power generator is reported. The electrical parameters, luminous images and spectrum diagnosis are presented. It is shown that the DBD possesses a large discharge current and an intense optical emission from the nitrogen second positive system below 400 nm. The gas temperature remains very close to room temperature regardless of pulse polarity. Luminous photographs with a short exposure time down to 2 ns indicate that no filament is observed and the discharge is homogeneous.

Mixture Preparation and Combustion of CNG Low-Pressure Compound Direct Injection Spark-Ignited Engines

A set of compressed natural gas (CNG) multi-point direct injection system of spark-ignited engines and the corresponding measurement and data acquisition systems were developed in this paper. Based on different injection modes, the mixture formation and combustion of CNG low-pressure direct injection (LPDI) engines were studied under varying factors such as air/ fuel ratio, injection timing. Meanwhile, three-dimensional simulations were adopted to explain the mixture formation mechanisms of CNG low-pressure compound direct injection (LPCDI) mode. On the basis of test results and simulation of the mixture homogeneous degree, the conception of injection window was proposed, and the LPCDI mode was proved to be more beneficial to the mixture concentration stratification formation in cylinder under lean-burning conditions, which resulted in effective combustion and stability.

电子封装超声互连研究新进展

超声振动摩擦和局部高温高压可实现同材或异材的低温、快速、可靠的互连,超声技术在电子封装中显示出无与伦比的技术优势。综述了超声引线键合、块体母材直接超声键合、母材/焊料/母材三体超声固相键合等超声固相键合技术,超声钎焊、超声瞬态液相扩散焊等超声液相键合技术,超声纳米烧结、混合(复合)焊料超声互连等超声固液混合键合技术。无论是高频低功率的高速超声键合,还是中频高功率超声常速键合,超声的作用规律和效果相似,其互连质量和互连机理与接触材料及其状态有着最为密切的关系;考虑由于超声互连过程快、时间短、互连界面窄、接头不透明,可以采用焊接实时高速摄像技术和同步辐射X射线成像技术相结合,实时观察液态焊料润湿流动、焊料颗粒运动轨迹、母材的剥离过程及界面形成规律;考虑由于微焊点尺寸放大,可以借助温度传感器和压力传感器进行超声的温度效应和瞬态压强实时测量;基于双超/多超声诸多影响因素,多超声的数值模拟分析将成为微焊点超声互连机理研究的有效手段。

聚乙二醇修饰杨梅苷固体脂质纳米粒制备及其体内药动学研究

目的制备聚乙二醇修饰杨梅苷固体脂质纳米粒,并考察其体内药动学。方法高压均质法制备聚乙二醇修饰固体脂质纳米粒,测定包封率、载药量、粒径、Zeta电位,单因素试验优化处方,XRPD进行晶型分析,考察体外释药、稳定性。24只大鼠随机分为4组,分别灌胃给予杨梅苷、杨梅苷固体脂质纳米粒、杨梅苷固体脂质纳米粒+聚乙二醇硬脂酸酯、聚乙二醇修饰杨梅苷固体脂质纳米粒的0.5%CMC-Na混悬液(150 mg/kg),于不同时间点采血,HPLC法测定杨梅素血药浓度,计算主要药动学参数。结果最优处方为药脂比1∶15,单硬酯酸甘油酯与聚乙二醇硬脂酸酯比例10∶1,泊洛沙姆188浓度0.8%,均质次数8次,包封率为81.75%,载药量为5.04%,粒径为207.56 nm,PDI为0.092,Zeta电位为-14.79 mV。杨梅苷以无定型状态存在于聚乙二醇修饰固体脂质纳米粒中,18 h内累积释放度为64.71%,模拟胃液中2 h内、模拟肠液中12 h内稳定性良好。与原料药、固体脂质纳米粒比较,聚乙二醇修饰固体脂质纳米粒t_(max)延长(P<0.05),C_(max)、AUC_(0~t)、AUC_(0~∞)升高(P<0.05,P<0.01),相对生物利用度与原料药相比增加至4.60倍。结论聚乙二醇修饰固体脂质纳米粒可改善杨梅苷稳定性,促进其口服吸收。

光甘草定烟酰胺纳米乳的制剂评价与透皮吸收

为提高光甘草定和烟酰胺的透皮吸收性能,利用两种高能乳化法制备了纳米乳(HPH-NE和HSSU-NE),对其形态、粒径、Zeta电位、稳定性和皮肤渗透性能进行了评价与考察.结果表明:两种纳米乳颗粒均为规则球形,未见聚集现象,平均粒径分别为51.60 nm和42.98 nm,Zeta电位分别为-50.44 mV和-68.50 mV,并且在离心、4℃和20℃以及加速试验条件下均具有较好的稳定性,两种方法制成的纳米乳相对普通乳液具有更好的皮肤渗透性能,光甘草定的平均渗透速率提高3~5倍,烟酰胺的平均渗透率提高1.6~2.6倍,为光甘草定的纳米制剂以及化妆品应用研究奠定了坚实基础.