Effect of Process Parameters on Tensile Strength of Friction Stir Welded Cast LM6 Aluminium Alloy Joints

This paper reports the effect of friction stir welding （FSW） process parameters on tensile strength of cast LM6 aluminium alloy. Joints were made by using different combinations of tool rotation speed, welding speed and axial force each at four levels. The quality of weld zone was investigated using macrostructure and microstructure analysis. Tensile strength of the joints were evaluated and correlated with the weld zone hardness and microstructure. The joint fabricated using a rotational speed of 900 r/min, a welding speed of 75 mm/min and an axial force of 3 kN showed superior tensile strength compared with other joints. The tensile strength and microhardness of the welded joints for the optimum conditions were 166 MPa and 64.8 Hv respectively.

GRAIN BOUNDARY SEGREGATION AND INTERGRANULAR BRITTLENESS IN HIGH STRENGTH ALUMINIUM ALLOY

ＧＲＡＩＮＢＯＵＮＤＡＲＹＳＥＧＲＥＧＡＴＩＯＮＡＮＤＩＮＴＥＲＧＲＡＮＵＬＡＲＢＲＩＴＴＬＥＮＥＳＳＩＮＨＩＧＨＳＴＲＥＮＧＴＨＡＬＵＭＩＮＩＵＭＡＬＬＯＹ￥Ｓｏｎｇ，Ｒｅｎｇｕｏ；Ｚｈｅｎｇ，Ｍｅｉｇｕａｎｇ（ＤｅｐａｒｒｍｅｎｔｏｆＭａｔｅｒｉ...

Effect of process parameters on tensile strength of friction stir welded cast A356 aluminium alloy joints

A356 is a high strength aluminium-silicon cast alloy used in food,chemical,marine,electrical and automotive industries.Fusion welding of this cast alloy will lead to many problems such as porosity,micro-fissuring,and hot cracking.However,friction stir welding（FSW） can be used to weld this cast alloy without above mentioned defects.An attempt was made to study the effect of FSW process parameters on the tensile strength of cast A356 aluminium alloy.Joints were made using different combinations of tool rotation speed,welding speed and axial force.The quality of weld zone was analyzed by macrostructure and microstructure analyses.Tensile strengths of the joints were evaluated and correlated with the weld zone hardness and microstructure.The joint fabricated using a rotational speed of 1000 r/min,a welding speed of 75 mm/min and an axial force of 5 kN showed a higher tensile strength compared to the other joints.

Mechanical property and corrosion behavior of aged Cu-20Ni-20Mn alloy with ultra-high strength

The ultra-high strength Cu-20Ni-20 Mn alloy was prepared by vacuum melting and its mechanical property and corrosion behavior were investigated. After thermomechanical treatment, the alloy exhibited an ultra-high tensile strength of 1204 MPa and the applicable elongation of up to 6.2%. With the increasing exposure time in 3.5% Na Cl solution, the corrosion current of the alloy decreased, while the polarization resistance and the charge-transfer resistance of the corrosion surface increased. The corrosion products formed on the surface of the alloy exposed for 1 d, and further corrosion made the corrosion product layer much dense, increasing the corrosion resistance and protecting the alloy from further corrosion.

Comparison of RSM with ANN in predicting tensile strength of friction stir welded AA7039 aluminium alloy joints

磨擦搅动(FSW ) 焊接是一种创新稳固的州的加入技术并且在太空，栏杆，为加入铝的汽车、海洋的工业，镁，锌和铜被采用了合金。FSW 过程参数象工具那样旋转速度，焊接速度，轴的力量，在决定焊接质量起一个主要作用。二个方法，反应表面方法论和人工的神经网络被用来预言磨擦的张力的强度搅动焊接 AA7039 铝合金。实验基于三个因素被进行，三水平、中央的合成的脸与完整的复制技术集中了设计，并且数学模型被开发。敏感分析被执行识别批评参数。通过反应表面方法论获得的结果与通过人工的神经网络的那些相比。

Strength properties examination of high zinc aluminium alloys inoculated with Ti addition

This paper includes studies on the influence of grain refinement treatment with respect to the composition and structure of high zinc aluminium casting alloys on the changes of their tensile properties. The Al-20 wt.%Zn alloy was inoculated with master alloys Al Ti5B1 and Al Ti3C0.15 to determine the impact of a variable titanium addition on the tensile properties of Al Zn20 alloy, and determine on this basis an optimal addition of Ti that would ensure the improvement of elongation of alloys cast in the sand mould, at the same time maintaining high tensile strength. Within the studies, light microscopy(LM) and strength tests were applied. Experimental results showed that the inoculation of high zinc aluminium alloy Al Zn20 with the master alloys Al Ti5B1 and Al Ti3C0.15 causes intensive structure refinement, while the intensity of reaction of both master alloys is comparable. The Al Ti3C0.15 master alloy addition, selected for further studies, introducing about 100 ppm Ti, enhances the tensile properties of the alloy; the elongation increases about 20% and tensile strength increases about 10% against the initial values(uninoculated alloy). Further increase of the Ti addition up to 500–600 ppm leads to the "overinoculation" effect that is accompanied by the decrease of elongation. Therefore,the Ti addition should be reduced to the level of about 100 ppm which ensures obtaining a set of optimal properties.

Heat treatment of 7xxx series aluminium alloys—Some recent developments

The 7xxx series alloys are heat treatable wrought aluminium alloys based on the Al-Zn-Mg（-Cu） system. They are widely used in high-performance structural aerospace and transportation applications. Apart from compositional, casting and thermo-mechanical processing effects, the balance of properties is also significantly influenced by the way in which the materials are heat-treated. This paper describes the effects of homogenisation, solution treatment, quenching and ageing treatments on the evolution of the microstructure and properties of some important medium to high-strength 7xxx alloys. With a focus on recent work at Monash University, where the whole processing route from homogenisation to final ageing has been studied for thick plate products, it is reported how microstructural features such as dispersoids, coarse constituent particles, fine-scale precipitates, grain structure and grain boundary characteristics can be controlled by heat treatment to achieve improved microstructure-property combinations. In particular, the paper presents methods for dissolving unwanted coarse constituent particles by controlled high- temperature treatments, quench sensitivity evaluations based on a systematic study of continuous cooling precipitation behaviour, and ageing investigations of one-, two- and three-step ageing treatments using experimental and modelling approaches, in each case, the effects on both the microstructure and the resulting properties are discussed.

Effect of Pulsed Current TIG Welding Parameters on Pitting Corrosion Behaviour of AA6061 Aluminium Alloy

Medium strength aluminium alloy （Al-Mg-Si alloy） has gathered wide acceptance in the fabrication of light weight structures requiring a high strength-to weight ratio, such as transportable bridge girders, military vehicles, road tankers and railway transport systems. The preferred welding process for aluminium alloy is frequently TIG （tungsten inert gas） welding due to its comparatively easier applicability and better economy.In the case of single pass TIG welding of thinner section of this alloy, the pulsed current has been found beneficial due to its advantages over the conventional continuous current process. The use of pulsed current parameters has been found to improve the mechanical properties of the welds compared to those of continuous current welds of this alloy due to grain refinement occurring in the fusion zone. A mathematical model has been developed to predict pitting corrosion potential of pulsed current TIG welded AA6061 aluminium alloy.Factorial experimental design has been used to optimize the experimental conditions. Analysis of variance technique has been used to find out the significant pulsed current parameters. Regression analysis has been used to develop the model. Using the developed model pitting corrosion potential values have been estimated for different combinations of pulsed current parameters and the results are analyzed in detail.

Microstructure and tensile properties of friction stir welded dissimilar AA6061-AA5086 aluminium alloy joints

The fusion welding of dissimilar heat treatable and non-heat treatable aluminium alloy faced many problems related to solidification. The difficulties can be overcome to achieve the combined beneficial properties of both aluminium alloys using friction stir welding(FSW). The microstructural features and tensile properties of friction stir welded(FSW) similar and dissimilar joints made of AA6061 and AA5086 aluminium alloys were investigated. The microstructures of various regions were observed and analyzed by means of optical and scanning electron microscopy. Microhardness was measured at various zones of the welded joints. The tensile properties of the joints were evaluated and correlated with the microstructural features and microhardness values. The dissimilar joint exhibits a maximum hardness of HV 115 and a joint efficiency of 56%. This was attributed to the defect free stir zone formation and grain size strengthening.

Developing friction stir welding window for AA2219 aluminium alloy

A friction stir welding window was developed for effective joining of AA2219 aluminium alloy. Joints were fabricated using different combination of process parameters such as rotational speed and welding speed. Based on macrostructural analysis, the friction stir welding window was constructed. The strength values of joints at different regions of friction stir welding window were analyzed using tensile properties, microstructural studies, and the fracture location of joints was correlated with the lowest hardness distribution profiles. These windows will act as reference maps for selecting appropriate friction stir welding process parameters to get good quality welds of AA2219 aluminium alloys.

Effect of tool tilt angle on strength and microstructural characteristics of friction stir welded lap joints of AA2014-T6 aluminum alloy

Friction stir welding(FSW)has been extensively adopted to fabricate aluminium alloy joints by incorporating various welding parameters that include welding speed,rotational speed,diameters of shoulder and pin and tool tilt angle.FSW parameters significantly affect the weld strength.Tool tilt angle is one of the significant process parameters among the weld parameters.The present study focused on the effect of tool tilt angle on strength of friction stir lap welding of AA2014-T6 aluminium alloy.The tool tilt angle was varied between 0°and 4°with an equal increment of 1°.Other process parameters were kept constant.Macrostructure and microstructure analysis,microhardness measurement,scanning electron micrograph,transmission electron micrograph and energy dispersive spectroscopy analysis were performed to evaluate the lap shear strength of friction stir lap welded joint.Results proved that,defect-free weld joint was obtained while using a tool tilt angle of 1°to 3°.However,sound joints were welded using a tool tilt angle of 2°,which had the maximum lap shear strength of 14.42 kN and microhardness of HV 132.The joints welded using tool tilt angles of 1°and 3°yielded inferior lap shear strength due to unbalanced material flow in the weld region during FSW.

Effect of tool pin profile on microstructure and tensile properties of friction stir welded dissimilar AA 6061e AA 5086 aluminium alloy joints

Joints between two different grades of aluminium alloys are need of the hour in many light weight military structures.In this investigation,an attempt has been made to join the heat treatable(AA 6061) and non-heat treatable(AA 5086) aluminium alloys by friction stir welding(FSW)process using three different tool pin profiles like straight cylindrical,taper cylindrical and threaded cylindrical.The microstructures of various regions were observed and analyzed by means of optical and scanning electron microscope.The tensile properties and microhardness were evaluated for the welded joint.From this investigation it is founded that the use of threaded pin profile of tool contributes to better flow of materials between two alloys and the generation of defect free stir zone.It also resulted in higher hardness values of 83 HV in the stir zone and higher tensile strength of 169 MPa compared to other two profiles.The increase in hardness is attributed to the formation of fine grains and intermetallics in the stir zone,and in addition,the reduced size of weaker regions,such as TMAZ and HAZ regions,results in higher tensile properties.

Impact strength and structural refinement of A380 aluminum alloy produced through gas-induced semi-solid process and Sr addition

Semi-solid processing of A380 aluminum alloy was performed by gas induced semi-solid(GISS)process.The effects of argon inert gas flow rate,starting temperature and duration of gas purging as key GISS parameters and also modification with Sr on the structural refinements,hardness and impact strength of GISS alloys were investigated.Microstructural evolution shows that there is an important effect of the pouring temperature and Sr addition on the morphology and size of primaryα(A1)in the alloy to change from coarse dendritic to fine globular structure.The best sample which has fine grains of 51.18μm in average size and a high level of globularity of 0.89 is achieved from a GISS processing of Sr modified alloy in which the gas purging started at 610℃.The impact strength of the GISS optimized samples((4.67±0.18)J/cm^(2))shows an increase of about 40%with respect to the as-cast sample due to the globular structure and fibrous Si morphology.Moreover,the hardness of the optimized GISS sample((89.34±2.85)HB)increases to(93.84±3.14)HB by modification with the Sr and GISS process.The fracture surface of Sr modified alloy is also dominated by complex topography showing typical ductile fracture features.

Process parameters optimization for friction stir welding of RDE-40 aluminium alloy using Taguchi technique

Taguchi approach was applied to determine the most influential control factors which will yield better tensile strength of the joints of friction stir welded RDE-40 aluminium alloy. In order to evaluate the effect of process parameters such as tool rotational speed, traverse speed and axial force on tensile strength of friction stir welded RDE-40 aluminium alloy, Taguchi parametric design and optimization approach was used. Through the Taguchi parametric design approach, the optimum levels of process parameters were determined. The results indicate that the rotational speed, welding speed and axial force are the significant parameters in deciding the tensile strength of the joint. The predicted optimal value of tensile strength of friction stir welded RDE-40 aluminium alloy is 303 MPa. The results were confirmed by further experiments.

Research and development of hot-rolled ultra-high strength steel at Baosteel

The effects of the composition and cooling process on the microstructures and properties of hot-rolled ultra-high strength low alloy （HSLA） steel, complex phase steel and martensite steel were studied in the laboratory. And S700MC and MP1200 ultra-high strength steels were trial produced at the 1 880 mm hot-rolling line of Baosteel. Compared with conventional hot-rolled high strength products,the idea that water is alloy was applied in the newly developed hot-rolled ultra-high strength steel. By the use of the economical composition design and controlled cooling after hot-rolling effectively,ultra-high strength steel of different steel grades can be obtained.

Effect of pre-recovery on microstructure and properties of rolled Al-12.18Zn-3.31Mg-1.43Cu-0.20Zr-0.04Sr aluminum alloy

The independently designed and manufactured ultra-high-strength aluminum alloy Al-12.18 Zn-3.31 Mg-1.43 Cu-0.20 Zr-0.04 Sr was investigated via scanning electron microscopy observations, X-ray diffraction analysis, hardness tests, electrical conductivity tests, tensile tests, intergranular corrosion tests, and exfoliation corrosion tests. The effect of pre-recovery on the microstructure and mechanical properties of this aluminum alloy was also studied. The results show that the pre-recovery heat treatment releases deformation energy, inhibits recrystallization, and decreases the dislocation density. Although the pre-recovery heat treatment has little effect on the hardness, electrical conductivity, and elongation of this aluminum alloy, it can dramatically improve the alloy's tensile strength(the maximum tensile strength increased from 785.0 MPa to 809.2 MPa). Moreover, the tensile properties of this aluminum alloy have a certain degree of isotropy, and the pre-recovery heat treatment does not affect this property. In addition, the rolled aluminum alloy exhibits good corrosion resistance, but the effect of the pre-recovery heat treatment on the alloy's resistance to intergranular and exfoliation corrosion is negligible.

高强铝合金腐蚀行为及评价方法研究进展

高强铝合金具有比强度高、加工性能好等特点,广泛应用于航空、航天等领域。腐蚀是影响高强铝合金服役安全稳定的重要因素。本文从高强铝合金的制备工艺出发,重点讨论热处理引起的组织结构变化对高强铝合金耐腐蚀性能的影响,分析高强铝合金的组织结构与腐蚀行为之间的对应关系,提出增强高强铝合金耐蚀性的研究方向。高强铝合金中的元素及相偏析,易导致其组织结构的电化学不均匀,引发基体腐蚀。因此,在合金成分优化的基础上,调控高强铝合金的熔融铸造工艺、加工成形工艺、热处理工艺,制备出元素及第二相分布均匀、电化学性质均一的组织结构,对改善高强铝合金的耐蚀性至关重要。此外,合金中无析出相区域的宽度及晶界析出相间的距离、分布等对合金的腐蚀敏感性具有重要的影响,深入研究并阐明无析出相区域等各类组织结构对合金腐蚀行为的影响规律及机制,是制备高耐蚀高强铝合金的前提。通过优化时效、形变热处理等热处理方法,开发新型的复合热处理方法以平衡高强铝合金的力学性能和耐腐蚀性能。同时,本文论述了高强铝合金耐腐蚀性能的实验方法及评价方法。为了更加高效正确地评估高强铝合金的耐蚀性及服役安全,未来还需要在传统评价方法与数字孪生、虚拟仿真实验、机器学习等现代化数据处理技术的联合使用方面开展进一步的研究工作。

时效温度对7050铝合金屈服强度的影响与本构模型研究

目的预测不同时效条件下7050铝合金力学性能的演化规律,为多级快速时效热处理工艺提供理论基础。方法分别在120、160、180℃温度下对7050铝合金进行0~8h时效热处理,并进行室温单拉试验,获得相应时效条件组合的应力-应变曲线及屈服强度演化曲线,建立统一时效本构模型,模拟微观组织(沉淀半径、溶质浓度)的演化规律,根据微观组织的演化规律,模拟由析出强度与固溶强度组成的屈服强度的演化规律。结果在不同时效温度下,模拟的屈服强度演化规律与试验结果基本保持一致,模拟的微观组织演化规律与理论分析结果基本保持一致。在160℃时效热处理8h和180℃时效热处理2h条件下得到了试验峰值屈服强度,分别为578.6MPa和555.8MPa,在模拟结果中也得到了相应的演化结果。在120℃下,屈服强度的试验结果与模拟结果均呈上升趋势。结论所建立的统一本构模型考虑了时效温度、时效时间的影响,成功预测了不同时效温度条件下析出相半径、溶质浓度等微观变量的演化规律,这些变量都有助于预测合金析出强度与固溶强度的演化规律,进而成功预测了由这2个强度分量组成的屈服强度的演化规律。

Mechanical and fatigue properties of self-piercing riveted joints in high-strength steel and aluminium alloy

Static tensile and fatigue tests were performed on shear and tensile self-piercing riveted aluminium-steel structures to evaluate their mechanical and fatigue properties. The influences of the thickness and the strength of the high strength steel on mechanical and fatigue performances were investigated based on the tensile and F-N curves of the joints. The results show that mechanical and fatigue properties of the shear self-piercing riveted joints are much better than those of the tensile self-piercing riveted joints. Mechanical and fatigue performances of the two joints were significantly influenced by the thickness and strength of the steel sheet, and were markedly improved when the thickness of steel sheet increased. The steel strength showed significantly different effects on shear and tensile riveted structures, i. e. , when the steel strength increased, the strength of the shear structure greatly increased while the tensile structure just had a slight increase in the strength. Fatigue failure generally occurred in the sheet materials and the fatigue crack location changed with increasing the sheet thickness and the sheet strength.

多道次拉伸和感应电流处理5052铝合金的力学性能和显微组织演变

提出一种多道次拉伸和感应电流处理(IEPT)相结合的复合成形方法,采用TEM和EBSD揭示感应电流对材料显微组织和力学性能的影响规律。结果表明,采用4次拉伸5%和拉伸后放电,材料伸长率比原始材料增加145%。预拉伸试样经过IEPT处理后,强度下降、塑性提高,材料的位错密度下降,晶粒变形结构向亚结构转变,同时晶粒尺寸略有增加。感应电流减弱材料的各向异性,出现新的<111>//TD织构。电塑性效应和焦耳热效应的结合增强位错运动和空位移动。采用ANSYS软件模拟板料的温度分布,最高温度达到144.7℃。材料强度的理论计算结果与实验数据一致。