Ultra-high cycle fatigue behavior of high strength steel with carbide-free bainite/martensite complex microstructure

The ultra-high cycle fatigue behavior of a novel high strength steel with carbide-free bainite/martensite （CFB/M） complex microstructure was studied. The ultra-high cycle fatigue properties were measured by ultrasonic fatigue testing equipment at a frequency of 20 kHz. It is found that there is no horizontal part in the S-N curve and fatigue fracture occurs when the life of specimens exceeds 10^7 cycles. In addition, the origination of fatigue cracks tends to transfer from the surface to interior of specimens as the fatigue cycle exceeds 10^7, and the fatigue crack originations of many specimens are not induced by inclusions, but by some kind of ＂soft structure＂. It is shown that the studied high strength steel performs good ultra-high cycle fatigue properties. The ultra-high fatigue mechanism was discussed and it is suggested that specific CFB/M complex microstructure of the studied steel contributes to its superior properties.

Microstructure and Mechanical Properties of Aer Met 100 Ultra-high Strength Steel Joints by Laser Welding

AerMet100 ultra-high strength steel plates with a thickness of 2 mm were welded using a COz laser welding system. The influences of the welding process parameters on the morphology and microstructure of the welding joints were investigated, and the mechanical property of the welding joints was analyzed. The experimental results showed that the fusion zone of welding joint mainly consisted of columnar grains and a fine dendrite substructure grew epitaxially from the matrix. With the other conditions remaining unchanged, a finer weld microstructure was along with the scanning speed increase. The solidification microstructure gradually transformed from cellular crystal into dendrite crystal and the spaces of dendrite secondary arms rose from the fusion line to the center of the fusion zone. In the fusion zone of the weld, the rapid cooling caused the formation of martensite, which led the microhardness of the fusion zone higher than that of the matrix and the heat affected zone. The tensile strength of the welding joints was tested as 1 700 MPa, which was about 87% of the matrix. However, the tensile strength of the welding joints without defects existed was tested as 1832 MPa, which was about 94% of the matrix.

Manifestations in Corrosion Prophase of Ultra-high Strength Steel 30CrMnSiNi2 A in Sodium Chloride Solutions

The corrosion behaviors of ultra-high strength steel 30CrMnSiNi2A in sodium chloride solution were studied by weight loss and electrochemical methods. The morphology of corrosion products was observed using scanning electron microscopy（SEM） and the composition was analyzed using an energy dispersive spectroscopy（EDS） and X-Ray diffraction （XRD）. The experimental results showed that the corrosion came from pitting corrosion and the rust layer was composed of outer rust layer γ-FeOOH and inner rust layer Fe_2O_3 with a little β-FeOOH. The correlation between corrosion rate and test time accorded with exponential rule. The corrosion current measured by polarization methods was higher than that calculated by weight loss method after a long-time immersion, the main reason was that,β-FeOOH and γ-Fe_2O_3 transformed by γ-FeOOH led to overestimating corrosion rate. The processes of corrosion prophase were obtained from XRD and EIS results. The corrosion product, Fe（OH）_2 formed at the initial stage stayed at a non-steady state and then consequently transferred to γ-FeOOH, γ-Fe_2O_3 or β-FeOOH.

Analysis of the effect of geometrical parameters on fatigue performance of spot-weld joint for ultra-high strength steel

This paper studied the spot welding structure of ultra-high strength steel 22MnB5.ANSYS software was adopted to simulate its static strength;BS5400 algorithm was used to calculate the fatigue life;and the grouping method was used to test the fatigue performance of tensile shear spot weld specimens.The simulation results were in good agreement with the experimental values.Based on the validation of the simulation method,influences of different structural parameters on static strength and fatigue life were explored by adopting single factor.The results showed that within the selected structure parameter range,increase of the sheet thickness,nugget diameter,sheet width and overlapping length can lead to longer fatigue life.Besides,the fatigue life of spot weld took on a linear relationship with the overlapping length,a DoseResp relationship with the sheet thickness,and a single exponential decay relationship with the sheet width and the nugget diameter.Moreover,in order to estimate the impact from various parameters on the fatigue life of the specimens,the Taguchi orthogonal design method was applied in the simulation design.The simulating result indicated that influence of the sheet thickness on fatigue life was the most significant.In addition,the effects of nugget diameter,sheet width and overlapping length on fatigue life were reduced in turn.

Neural network modeling to evaluate the dynamic flow stress of high strength armor steels under high strain rate compression

An artificial neural network(ANN) constitutive model is developed for high strength armor steel tempered at 500 C, 600 C and 650 C based on high strain rate data generated from split Hopkinson pressure bar(SHPB) experiments. A new neural network configuration consisting of both training and validation is effectively employed to predict flow stress. Tempering temperature, strain rate and strain are considered as inputs, whereas flow stress is taken as output of the neural network. A comparative study on Johnsone Cook(Je C) model and neural network model is performed. It was observed that the developed neural network model could predict flow stress under various strain rates and tempering temperatures. The experimental stressestrain data obtained from high strain rate compression tests using SHPB, over a range of tempering temperatures(500e650 C), strains(0.05e0.2) and strain rates(1000e5500/s) are employed to formulate Je C model to predict the high strain rate deformation behavior of high strength armor steels. The J-C model and the back-propagation ANN model were developed to predict the high strain rate deformation behavior of high strength armor steel and their predictability is evaluated in terms of correlation coefficient(R) and average absolute relative error(AARE). R and AARE for the Je C model are found to be 0.7461 and 27.624%, respectively, while R and AARE for the ANN model are 0.9995 and 2.58%, respectively. It was observed that the predictions by ANN model are in consistence with the experimental data for all tempering temperatures.

Research and development of hot-rolled ultra-high strength steel at Baosteel

The effects of the composition and cooling process on the microstructures and properties of hot-rolled ultra-high strength low alloy （HSLA） steel, complex phase steel and martensite steel were studied in the laboratory. And S700MC and MP1200 ultra-high strength steels were trial produced at the 1 880 mm hot-rolling line of Baosteel. Compared with conventional hot-rolled high strength products,the idea that water is alloy was applied in the newly developed hot-rolled ultra-high strength steel. By the use of the economical composition design and controlled cooling after hot-rolling effectively,ultra-high strength steel of different steel grades can be obtained.

Internal oxidation of hot-rolled ultra-high strength steel and its effect on the surface quality of cold-rolled sheets

In this study,the scale and internal oxidation of hot-rolled ultra-high strength steel sheets were characterized.It was found that both the formation of the scale and the internal oxidation of Si and Mn depended on the coiling temperature and position of the steel sample on the strip coil.At a relatively high coiling temperature,a large amount of internal oxidation was observed on the samples cut from the middle of the coil.The depth of the internal oxidation zone exceeded 10 μm and a thin iron layer covering the scale was observed in some cases.Pickling and cold-rolling experiments were conducted on selected samples.Scale pickling was found to be greatly delayed by the formation of an iron layer,which frequently resulted in under-pickled defects.In addition,pickling of the entire internal oxidation zone was difficult,except at the grain boundaries,where the degree of internal Si and Mn oxidation was enriched.The surface of the cold-rolled steel sheet was ruined by the remaining oxidation zone in the subsurface of the pickled steel.The internal oxidation of hot-rolled ultra-high strength steel must be precisely controlled to improve the subsequent surface quality of cold-rolled steel.

Corrosion Behavior of Ultra-high Strength Steel 300M in Different Simulated Marine Environments

Corrosion behavior of 300M in neutralcorrosion environments containing Na Clsimulated by totalimmersion（TI）,salt spraying（SS）and periodic immersion（PI）,was investigated by surface analysis techniques,corrosion weight-loss method,and electrochemicalmeasurements.In totalimmersion environment,rust on the steelconsisted of a porous outer rust layer with main constituent of γ-Fe OOH,and an inner rust layer of dense Fe_3O_4 film with network broad cracks.In salt spraying environment,outer rust with main composition of γ-Fe OOH/α-Fe OOH/Fe_3O_4 was compact,and inner rust showed dense Fe_3O_4 film.Rust formed by periodic immersion exhibited a compact outer rust layer with constituent of α-Fe OOH/γ-Fe OOH/Fe_3O_4 and an inner rust layer with composition of α-Fe OOH/α-Fe_2O_3;inner rust showed a ultra-dense film adherent to the steel.The corrosion rate showed a rule of vss（salt spraying）〉vti（totalimmersion）〉〉vpi（periodic immersion）in 0-240 h,and vss≈vti？vpiin 240-720 h.The rust formed by periodic immersion was dense and compact,with stable electrochemicalproperties,and had excellent protection on the steel.Humidity and oxygen concentration in allthe environments played major roles in rust formation.

Study on welding process performance of HG70D high strength steel plate

In this paper, the performance of HG70D welded joint of ultra-high strength steel plates is presented, and the performance of HG70D and Q345B welded joints is studied. The high strength steel plate HG70D showed excellent weldability. Through the X-ray inspection of welded joints, tensile strength, impact test and bending performance test, the comprehensive performance of the joint was excellent. The macroscopic and microscopic metallographic analysises of the welded joints show that the welding seams included pearlite, sorbite, ferrite, etc. The influence of stress annealing temperature on HG70D of high strength steel plate was analyzed by heat treatment.

IMPROVEMENT ON SUSCEPTIBILITY OF ULTAR-HIGH STRENGTH STEEL TO STRESS CORROSION CRACKING BY HIGH TEMPERATURE QUENCHING

The effect of quenching temperature on the stress corrosion cracking of 30Cr3SiNiMoV ultra-high strength steel in 3.5% NaCl aqueous solution has been studied.The threshold K_(ISCC) may continuously increase with the quenching temperature raised from 870 to 1200℃ . All of the fractures are intergranular.The analyses of the segregation along prior austenitic grain boundaries,grain size and other microstructural factors reveal that the inerease of K_(ISCC) is mainly due to the coarsening of prior austenitic grains.

Investigation on microstructure and properties of a combined precipitation hardening ultrahigh strength steel

The microstructure and properties of a combined precipitation hardening ultrahigh strength steel with nano-sized carbides and intermetallics were studied systematically.The results show that after tempering at 300℃lots ofε-carbides are precipitated in the martensite,the strength rises and the toughness falls slightly.After tempering at 430℃,much coarser cementite lamina are precipitated in martensitic laths,which causes the impact toughness falls to the minimum value.With temperature further increasing the cementites are dissolved and M_2C carbides,β-NiAl intermetallics and reverse austenite begin to precipitate.The tensile strength and yield strength achieve the peak value at 470℃,490℃respectively.The tested steel achieve a tensile strength of 2 120 MPa,a yield strength of 1 950 MPa and impact energy of 54 J/cm^2 after optimum tempering at 510℃.When tempering temperature is above 530℃the M_2C carbides and reverse austenite is coarsening.After tempering at 560℃the reverse austenite reaches the maximum volume fraction in present work.

Development of ultra high strength special steels and wrought nickel base superalloys

Ultra-high strength special steels and wrought Ni-base superalloys are been ever increasingly applied in aircraft and aerospace,power generation,oil-gas and other industries.The development of those materials is driven by tougher working conditions,higher efficiency,environment consideration,resource limitation and cost reduction. This presentation will focus on the development of ultra high strength special steels and wrought Ni-base superalloys in aircraft industry. The examples of ultra-high strength steels include: (1) Ultra-high strength stainless steels for landing gear and other structures; (2)High speed and high temperature main shaft bearing steels; (3) Ultra-high strength steels for jet engine main shaft. New and modified Ni-base superalloys will be discussed by examples of (1 )Low cost,process-friendly superalloys with higher performance; (2)Modification of hard-to-processed superalloys. Future development of those materials will be addressed.

Recent development of UHSS and its hot-dip galvanizing processes in Baosteel

Baosteel has excelled in automotive steel sheets in the past three decades.It has made a significant contribution to the development of China’s automotive industry by producing a wide range of high-quality steel products.Some milestones achieved by Baosteel automotive steel sheet were briefly reviewed.The current challenges in producing ultra-high strength steel(UHSS),especially hot-dip galvanized UHSS,were summarized.The most current advancements in UHSS and the corresponding hot-dip galvanizing processes were discussed.The galvanizability of Si-Mn-added QP steel and DP steel, Mn-added TWIP steel, and Al-added low-density steel has been improved by different techniques in Baosteel.

焊丝成分对超高强装甲钢焊接接头组织与性能的影响

利用气体保护电弧焊工艺完成了4.5 mm和9.0 mm超高强装甲钢的焊接,研究了焊丝(MG70S-6和ER307Si焊丝)成分对接头组织与性能的影响,通过光学显微镜(OM)、扫描电子显微镜(SEM)、能谱分析(EDS)、X射线衍射(XRD)等表征方法对焊接接头各区域进行微观组织和物相结构的分析,并测试了接头的硬度分布、拉伸性能和冲击韧性。结果表明,焊接接头成形质量良好,无明显未熔合、气孔、裂纹等缺陷,焊缝区组织为片状马氏体、针状铁素体和少量粒状贝氏体,完全淬火区组织为马氏体和贝氏体,不完全淬火区组织为马氏体和铁素体,回火区析出网状渗碳体。焊接接头的热影响区软化现象较为明显,接头难以达到与母材等强,断裂主要发生在焊缝区,呈现出脆性断裂特征。采用ER307Si焊丝焊接的9.0 mm装甲钢接头的焊缝室温冲击功达到94 J,完全满足使用要求。

不同焊接方法对超高强装甲钢焊接接头力学性能与组织的影响

装甲钢MAG工艺常采用奥氏体、铁素体不锈钢焊丝,使得焊接接头抗拉强度和硬度会大幅度降低,同时造成热影响区的局部软化,降低了装甲车辆的防护性能。为了满足超高强装甲钢焊接接头强度和硬度防护要求,该文对超高强装甲钢激光焊接工艺进行了研究,分别为MAG、激光自熔焊、激光填丝焊、激光‒电弧复合焊4种焊接方法,研究接头拉伸、弯曲、硬度等性能指标及接头组织。结果表明,激光焊接头的焊缝组织为粗大的板条马氏体,MAG焊缝组织为铁素体和粒状贝氏体;对于激光焊和MAG,淬火粗晶区均为粗针状马氏体,淬火细晶区为细小的针状马氏体,不完全淬火区为马氏体与铁素体的混合组织。激光焊接头的抗拉强度和硬度远高于MAG,激光焊接头的抗拉强度可达到母材的90%以上,硬度约为母材的82%,大大提高了防护型车辆的防护性能。然而,激光焊接头的抗弯强度要低于MAG,无论面弯还是背弯,激光焊弯曲试样通常在弯曲角度10°~30°之间即发生断裂,大大低于MAG弯曲角度90°(不断裂),从而限制了其使用场景。

Experimental Investigation of the Effect of the Material Damage Induced in Sheet Metal Forming Process on the Service Performance of 22MnB5 Steel

The use of ultra-high strength steels through sheet metal forming process offers a practical solution to the lightweight design of vehicles.However,sheet metal forming process not only produces desirable changes in material properties but also causes material damage that may adversely influence the service performance of the material formed.Thus,an investigation is conducted to experimentally quantify such influence for a commonly used steel（the 22MnB5 steel） based on the hot and cold forming processes.For each process,a number of samples are used to conduct a uniaxial tensile test to simulate the forming process.After that,some of the samples are trimmed into a standard shape and then uniaxially extended until fracture to simulate the service stage.Finally,a microstructure test is conducted to analyze the microdefects of the remaining samples.Based on the results of the first two tests,the effect of material damage on the service performance of 22MnB5 steel is analyzed.It is found that the material damages of both the hot and cold forming processes cause reductions in the service performance,such as the failure strain,the ultimate stress,the capacity of energy absorption and the ratio of residual strain.The reductions are generally lower and non-linear in the former process but higher and linear in the latter process.Additionally,it is found from the microstructure analysis that the difference in the reductions of the service performance of 22MnB5 by the two forming processes is driven by the difference in the micro damage mechanisms of the two processes.The findings of this research provide a useful reference in terms of the selection of sheet metal forming processes and the determination of forming parameters for 22MnB5.

FATIGUE PROPERTIES OF META-BAINITE IN STEEL 40CrMnSiMoVA

The microstructure,strength,toughness and fatigue properties of an ultra-high strength steel 40CrMnSiMoVA have been investigated.The so-called meta-bainite,composed of thin re- tained austenite films within or between the bainitic ferrite lathes was found in the steel after isothermally quenched at 300℃ for 1h.In comparison with the martensite structure obtained by isothermally quenching in martensite range,the meta-bainite has more excellent strength and plasticity,lower notch sensitivity,stronger strain harden ability,higher fatigue strength, longer strain or impact fatigue life,slower crack propagation rate and more remarkable overload effect on increasing fatigue life.

Influence of refined hierarchical martensitic microstructures on yield strength and impact toughness of ultra-high strength stainless steel

The hierarchical martensitic features in ultra-high strength stainless steel(UHSSS),including the prior austenite grains,martensite packets,blocks and laths with the descending size,were refined to various extents by employing different thermomechanical processes and then carefully characterized.Their relation to yield strength and impact toughness was analyzed.We conclude that the refinement of martensitic structures could lead to the significant increase of yield strength,which follows the Hall-Petch relation with the effect grain size defined by high angle boundaries(HABs).Impact toughness of UHSSS depends on the frequency and capability for retained austenite(RA)grains at both HABs and martensite lath boundaries to trap the propagating cracks via strain-induced transformation,in which the film-like RA grains at lath boundaries appear to make the greater contribution.

Influence of Rust Layers on the Corrosion Behavior of Ultra-High Strength Steel 300M Subjected to Wet–Dry cyclic Environment with Chloride and Low Humidity

The influence of rust layers on the corrosion behavior of ultra-high strength steel 300M subjected to a simulated coastal atmosphere was investigated by corrosion weight loss, surface analysis techniques, and electrochemical methods. The results exhibit the presence of a large proportion of γ-FeOOH and α-FeOOH and a small amount of Fe3O4 in the outer rust layer. During the wet-dry cyclic process, the bonding performance and the density of outer rust layer deteriorate with the thickness of outer rust. The inner rust layer plays a main role on protectiveness, which can be attributed to the formation of an ultra-dense and adherent rust film with major constituent of α-FeOOH and α-Fe2O3 on the steel.

Effect of Martensite Fine Structure on Mechanical Properties of an 1100 MPa Grade Ultra-high Strength Steel

An 1100 MPa grade ultra-high strength steel with different martensite fine structures, characterized by prior austenite grain size, martensite packet size, block width and lath width, was studied by various heat treatment processes. The result shows that with decreasing prior austenite grain size, both the packet size and block width decrease, while the lath width has virtually no change. Accordingly, both strength and toughness increase, while total elongation decreases. The yield strength has a Hall Petch type relationship with the prior austenite grain size, packet size and block width, and the block width may be regarded as a key factor influencing strength. On the other hand, the ductile to brittle transition temperature （DBTT） is found to be more related lo the packet size, which may be considered as a dominant factor influencing toughness.