China is quite poor in argent resource. Roughly 80% of this industrial argent is imported every year. In order to improve the situation, we took advantage of rare earth (RE) mineral resource and successfully developed...China is quite poor in argent resource. Roughly 80% of this industrial argent is imported every year. In order to improve the situation, we took advantage of rare earth (RE) mineral resource and successfully developed the non-argent Lanthanum-tellurium-copper alloy as a substitute for industry argent-copper. In our research, we were able to successfully apply rare earth lanthanum to copper alloy. The defects as porosity, inclusion, etc. originating from nonvacuum melting processing were controlled. Fine grain was obtained. Meanwhile, the comprehensive properties of the copper alloy, such as strength, conductivity and thermal conductivity were improved. The research results in increasing conductivity and thermal conductivity by 5% and 15%, respectively, while the tensile strength is increased by 6% higher than Ag-Cu alloy. The anti-electric corrosion property is good, and there is no argent-cadmium steam population originating from the electric arc effect. The addition of lanthanum further reduces the content of oxygen and hydrogen. The optimum quantity of the addition of RE lanthanum in the copper alloy is 0.010% - 0.020% .展开更多
An attempt was made to optimize friction welding parameters to attain a minimum hardness at the interface and a maximum tensile strength of the dissimilar joints of AISI 304 austenitic stainless steel （ASS） and copp...An attempt was made to optimize friction welding parameters to attain a minimum hardness at the interface and a maximum tensile strength of the dissimilar joints of AISI 304 austenitic stainless steel （ASS） and copper （Cu） alloy using response surface methodology （RSM）. Three-factor, five-level central composite design matrix was used to specify experimental conditions. Twenty joints were fabricated using ASS and Cu alloy. Tensile strength and interface hardness were measured experimentally. Analysis of variance （ANOVA） method was used to find out significant main and interaction parameters and empirical relationships were developed using regression analysis. The friction welding parameters were optimized by constructing response graphs and contour plots using design expert software. The developed empirical relationships can be effectively used to predict tensile strength and interface hardness of friction welded ASS-Cu joints at 95% confidence level. The developed contour plots can be used to attain required level of optimum conditions to join ASS-Cu alloy by friction welding process.展开更多
The ultra-high strength Cu-20Ni-20 Mn alloy was prepared by vacuum melting and its mechanical property and corrosion behavior were investigated. After thermomechanical treatment, the alloy exhibited an ultra-high tens...The ultra-high strength Cu-20Ni-20 Mn alloy was prepared by vacuum melting and its mechanical property and corrosion behavior were investigated. After thermomechanical treatment, the alloy exhibited an ultra-high tensile strength of 1204 MPa and the applicable elongation of up to 6.2%. With the increasing exposure time in 3.5% Na Cl solution, the corrosion current of the alloy decreased, while the polarization resistance and the charge-transfer resistance of the corrosion surface increased. The corrosion products formed on the surface of the alloy exposed for 1 d, and further corrosion made the corrosion product layer much dense, increasing the corrosion resistance and protecting the alloy from further corrosion.展开更多
The effects of the composition and cooling process on the microstructures and properties of hot-rolled ultra-high strength low alloy （HSLA） steel, complex phase steel and martensite steel were studied in the laborat...The effects of the composition and cooling process on the microstructures and properties of hot-rolled ultra-high strength low alloy （HSLA） steel, complex phase steel and martensite steel were studied in the laboratory. And S700MC and MP1200 ultra-high strength steels were trial produced at the 1 880 mm hot-rolling line of Baosteel. Compared with conventional hot-rolled high strength products,the idea that water is alloy was applied in the newly developed hot-rolled ultra-high strength steel. By the use of the economical composition design and controlled cooling after hot-rolling effectively,ultra-high strength steel of different steel grades can be obtained.展开更多
Age hardening in Cu-3.2Ni-0.75Si (wt pct) and Cu-1.0Ni-0.25Si (wt pct) alloys from 723 to 823 K is studied. After an incubation period strengthening appears which is due to precipitates in the Cu-l.ONi-0.25Si (wt pct)...Age hardening in Cu-3.2Ni-0.75Si (wt pct) and Cu-1.0Ni-0.25Si (wt pct) alloys from 723 to 823 K is studied. After an incubation period strengthening appears which is due to precipitates in the Cu-l.ONi-0.25Si (wt pct) alloy. On other hand an immediate increase of the yield strength characterizes the aging of the alloy. This is followed by the regions of constant yield strength and further by a peak. The microstructure of the alloy was studied by, means of transmission electron microscope (TEM) and X-ray diffraction (XRD). Spinodal decomposition takes place followed by nucleation of the ordering coherent (Cu,Ni)3Si particles, further precipitation annealing coherent δ-Ni2Si nucleated within the (Cu,Ni)3Si particle. Any change of the yield strength can be described by an adequate change of the structure in the sample. The nature of the aging curves with a 'plateau' is discussed. The formulas of Ashby and Labusch can be used to explain the precipitation.展开更多
The independently designed and manufactured ultra-high-strength aluminum alloy Al-12.18 Zn-3.31 Mg-1.43 Cu-0.20 Zr-0.04 Sr was investigated via scanning electron microscopy observations, X-ray diffraction analysis, ha...The independently designed and manufactured ultra-high-strength aluminum alloy Al-12.18 Zn-3.31 Mg-1.43 Cu-0.20 Zr-0.04 Sr was investigated via scanning electron microscopy observations, X-ray diffraction analysis, hardness tests, electrical conductivity tests, tensile tests, intergranular corrosion tests, and exfoliation corrosion tests. The effect of pre-recovery on the microstructure and mechanical properties of this aluminum alloy was also studied. The results show that the pre-recovery heat treatment releases deformation energy, inhibits recrystallization, and decreases the dislocation density. Although the pre-recovery heat treatment has little effect on the hardness, electrical conductivity, and elongation of this aluminum alloy, it can dramatically improve the alloy's tensile strength(the maximum tensile strength increased from 785.0 MPa to 809.2 MPa). Moreover, the tensile properties of this aluminum alloy have a certain degree of isotropy, and the pre-recovery heat treatment does not affect this property. In addition, the rolled aluminum alloy exhibits good corrosion resistance, but the effect of the pre-recovery heat treatment on the alloy's resistance to intergranular and exfoliation corrosion is negligible.展开更多
基金Project supported by the National Scientific and Technological Achievements Spread Project (2004EC00299)Science and Technology Type Middle and Small Business Technique Invention Fund (04C26225121390)
文摘China is quite poor in argent resource. Roughly 80% of this industrial argent is imported every year. In order to improve the situation, we took advantage of rare earth (RE) mineral resource and successfully developed the non-argent Lanthanum-tellurium-copper alloy as a substitute for industry argent-copper. In our research, we were able to successfully apply rare earth lanthanum to copper alloy. The defects as porosity, inclusion, etc. originating from nonvacuum melting processing were controlled. Fine grain was obtained. Meanwhile, the comprehensive properties of the copper alloy, such as strength, conductivity and thermal conductivity were improved. The research results in increasing conductivity and thermal conductivity by 5% and 15%, respectively, while the tensile strength is increased by 6% higher than Ag-Cu alloy. The anti-electric corrosion property is good, and there is no argent-cadmium steam population originating from the electric arc effect. The addition of lanthanum further reduces the content of oxygen and hydrogen. The optimum quantity of the addition of RE lanthanum in the copper alloy is 0.010% - 0.020% .
文摘An attempt was made to optimize friction welding parameters to attain a minimum hardness at the interface and a maximum tensile strength of the dissimilar joints of AISI 304 austenitic stainless steel （ASS） and copper （Cu） alloy using response surface methodology （RSM）. Three-factor, five-level central composite design matrix was used to specify experimental conditions. Twenty joints were fabricated using ASS and Cu alloy. Tensile strength and interface hardness were measured experimentally. Analysis of variance （ANOVA） method was used to find out significant main and interaction parameters and empirical relationships were developed using regression analysis. The friction welding parameters were optimized by constructing response graphs and contour plots using design expert software. The developed empirical relationships can be effectively used to predict tensile strength and interface hardness of friction welded ASS-Cu joints at 95% confidence level. The developed contour plots can be used to attain required level of optimum conditions to join ASS-Cu alloy by friction welding process.
基金Project(2017YFB0306105)supported by the National Key R&D Program of ChinaProjects(51601227,51701241)supported by the National Natural Science Foundation of China。
文摘The ultra-high strength Cu-20Ni-20 Mn alloy was prepared by vacuum melting and its mechanical property and corrosion behavior were investigated. After thermomechanical treatment, the alloy exhibited an ultra-high tensile strength of 1204 MPa and the applicable elongation of up to 6.2%. With the increasing exposure time in 3.5% Na Cl solution, the corrosion current of the alloy decreased, while the polarization resistance and the charge-transfer resistance of the corrosion surface increased. The corrosion products formed on the surface of the alloy exposed for 1 d, and further corrosion made the corrosion product layer much dense, increasing the corrosion resistance and protecting the alloy from further corrosion.
文摘The effects of the composition and cooling process on the microstructures and properties of hot-rolled ultra-high strength low alloy （HSLA） steel, complex phase steel and martensite steel were studied in the laboratory. And S700MC and MP1200 ultra-high strength steels were trial produced at the 1 880 mm hot-rolling line of Baosteel. Compared with conventional hot-rolled high strength products,the idea that water is alloy was applied in the newly developed hot-rolled ultra-high strength steel. By the use of the economical composition design and controlled cooling after hot-rolling effectively,ultra-high strength steel of different steel grades can be obtained.
基金supported by the National Natural Science Foundation of China under contract No.50071026.
文摘Age hardening in Cu-3.2Ni-0.75Si (wt pct) and Cu-1.0Ni-0.25Si (wt pct) alloys from 723 to 823 K is studied. After an incubation period strengthening appears which is due to precipitates in the Cu-l.ONi-0.25Si (wt pct) alloy. On other hand an immediate increase of the yield strength characterizes the aging of the alloy. This is followed by the regions of constant yield strength and further by a peak. The microstructure of the alloy was studied by, means of transmission electron microscope (TEM) and X-ray diffraction (XRD). Spinodal decomposition takes place followed by nucleation of the ordering coherent (Cu,Ni)3Si particles, further precipitation annealing coherent δ-Ni2Si nucleated within the (Cu,Ni)3Si particle. Any change of the yield strength can be described by an adequate change of the structure in the sample. The nature of the aging curves with a 'plateau' is discussed. The formulas of Ashby and Labusch can be used to explain the precipitation.
基金financially supported by the Jiangsu Provincial Industrial Science and Technology Support Program (No. BE2008118)the Basic Research on Isotropic Ultra-high Strength Aluminum Matrix Composite (No. 6140922010201)
文摘The independently designed and manufactured ultra-high-strength aluminum alloy Al-12.18 Zn-3.31 Mg-1.43 Cu-0.20 Zr-0.04 Sr was investigated via scanning electron microscopy observations, X-ray diffraction analysis, hardness tests, electrical conductivity tests, tensile tests, intergranular corrosion tests, and exfoliation corrosion tests. The effect of pre-recovery on the microstructure and mechanical properties of this aluminum alloy was also studied. The results show that the pre-recovery heat treatment releases deformation energy, inhibits recrystallization, and decreases the dislocation density. Although the pre-recovery heat treatment has little effect on the hardness, electrical conductivity, and elongation of this aluminum alloy, it can dramatically improve the alloy's tensile strength(the maximum tensile strength increased from 785.0 MPa to 809.2 MPa). Moreover, the tensile properties of this aluminum alloy have a certain degree of isotropy, and the pre-recovery heat treatment does not affect this property. In addition, the rolled aluminum alloy exhibits good corrosion resistance, but the effect of the pre-recovery heat treatment on the alloy's resistance to intergranular and exfoliation corrosion is negligible.
