Combination of a reaction cell and an ultra-high vacuum system for the in situ preparation and characterization of a model catalyst

An in-depth understanding of the structure-activity relationship between the surface structure,chemical composition,adsorption and desorption of molecules,and their reaction activity and selectivity is necessary for the rational design of high-performance catalysts.Herein,we present a method for studying catalytic mechanisms using a combination of in situ reaction cells and surface science techniques.The proposed system consists of four parts:preparation chamber,temperatureprogrammed desorption(TPD)chamber,quick load-lock chamber,and in situ reaction cell.The preparation chamber was equipped with setups based on the surface science techniques used for standard sample preparation and characterization,including an Ar+sputter gun,Auger electron spectrometer,and a low-energy electron diffractometer.After a well-defined model catalyst was prepared,the sample was transferred to a TPD chamber to investigate the adsorption and desorption of the probe molecule,or to the reaction cell,to measure the catalytic activity.A thermal desorption experiment for methanol on a clean Cu(111)surface was conducted to demonstrate the functionality of the preparation and TPD chambers.Moreover,the repeatability of the in situ reaction cell experiment was verified by CO_(2) hydrogenation on the Ni(110)surface.At a reaction pressure of 800 Torr at 673 K,turnover frequencies for the methanation reaction and reverse water-gas shift reaction were 0.15 and 7.55 Ni atom^(-1) s^(-1),respectively.

CSRm Ultra-High Vacuum System

The new accelerator project （ HIRFL-CSR ） constructed at the Heavy Ion Research Facility in Lanzhou （HIRFL） is approaching completion. It is a multipurpose cooler-storage-ring system, consisting of a maim ring （CSRm）, an experimental ring （CSRe） and two transfer beam lines. The UHV system of CSRm is the most representative subsystem in the project. To minimize the beam loss due to charge exchange of the heavy ions with the residual gas molecules, the pressure of the CSRm vacuum system should reach 3.5 × 10^-9 Pa （N2 equivalent） and the pressure of 8 × 10^-10 Pa is expected for very heavy ion such as uranium to make its lifetime longer than 50 s in the ring. Now, the vacuum system of CSRm has been completed and a pressure less than 5 × 10^-10 Pa has been obtained. In this paper the layout of the CSRm vacuum system, the vacuum equipment in CSRm, the treatment method for the CSRm vacuum chambers, and the installation and operation of the system will be reported.

Effect of Laser Welding on Properties of Dissimilar Joint of Al-Mg-Si and Al-Mn Aluminum Alloys

This study discusses the welding properties for the components of an aluminum-alloy ultra-high vacuum chamber and beam position monitor （BPM）.The welding parameters include the modes of laser output （pulsed wave and continuous wave）,welding speed,shield gas flow,welding bead structure,and focusing distance.The results showed that the welding defect rate of the pulsed wave type was larger than that of the continuous wave type.The crack in the welding bead reduced with decreasing welding speed.The fusion penetration of the welding bead was higher when the focusing distance was long enough to deepen into the welding material.Weld morphology during the experimental process revealed the proper flow of shield gas.The adaptability design of the welding bead structure in the preceding processes had more effect on overall welding structure and morphology.

Deposition and characterization of Pd-Ti thin film by sublimation

Introduction Pd/Ti double-layer thin film as non-evaporable getter(NEG)was deposited by sublimation,and its activation temperature was as low as 100℃.The Pd film was deposited in situ after Ti deposition to ensure no oxidization on Ti film.Pumping speed test and characterization method The pumping speed of the coated pipe was measured by a pumping speed test system.The sticking factor was calculated by Molflow.The surface morphology was observed by a scanning electron microscope(SEM).The chemical composition of the film was measured by an energy-dispersive spectrum inbuilt with the SEM.The crystalline structure of the film was measured using grazing incidence X-ray diffraction.Conclusion It was found that the pumping performance of the Pd/Ti film still remained high after 15 times of activation.The maximum pumping speed after heating at 100℃for 24 h was 1.1 L/s cm^(2)and 0.49 L/s cm^(2)for H_(2)and CO,respectively.It can be concluded that the key to reducing the activation temperature of NEG materials is to enhance the oxidation resistance of the surface of NEG.